[SOLVED] df -h does not reflect true root filesystem size

Why does df -h show root filesystem as being only 20G?
df -h
Filesystem Size Used Avail Use% Mounted on
/dev/mapper/cryptroot 20G 15G 4.6G 76% /
dev 7.7G 0 7.7G 0% /dev
run 7.7G 668K 7.7G 1% /run
tmpfs 7.7G 70M 7.7G 1% /dev/shm
tmpfs 7.7G 0 7.7G 0% /sys/fs/cgroup
tmpfs 7.7G 224K 7.7G 1% /tmp
/dev/sda1 239M 40M 183M 18% /boot
tmpfs 1.6G 8.0K 1.6G 1% /run/user/1000
That is what my df -h output looks like. My setup is full disk encryption using dm-crypt with LUKS, per the guide on arch wiki. I basically created one /boot partition and left the rest of the disk to be an encrypted partition for the root filesystem. So why is my system complaining about (and acting as if it's running out of space)? Have I forgotten something?
Thank you for reading this. Let me know if you need any more logs or info on my setup - I realise I haven't provided very much info here, but I can't think of what to provide.
Last edited by domentoi (2014-12-24 19:02:32)

This is lsblk:
NAME MAJ:MIN RM SIZE RO TYPE MOUNTPOINT
sda 8:0 0 465.8G 0 disk
├─sda1 8:1 0 250M 0 part /boot
└─sda2 8:2 0 465.5G 0 part
└─cryptroot 254:0 0 465.5G 0 crypt /
sdb 8:16 0 14.9G 0 disk
└─sdb1 8:17 0 14.9G 0 part
and fdisk -l
Disk /dev/sdb: 14.9 GiB, 16013942784 bytes, 31277232 sectors
Units: sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disklabel type: dos
Disk identifier: 0x5da5572f
Device Boot Start End Sectors Size Id Type
/dev/sdb1 2048 31275007 31272960 14.9G 73 unknown
Disk /dev/sda: 465.8 GiB, 500107862016 bytes, 976773168 sectors
Units: sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 4096 bytes
I/O size (minimum/optimal): 4096 bytes / 4096 bytes
Disklabel type: dos
Disk identifier: 0xa5018820
Device Boot Start End Sectors Size Id Type
/dev/sda1 * 2048 514047 512000 250M 83 Linux
/dev/sda2 514048 976773167 976259120 465.5G 83 Linux
Disk /dev/mapper/cryptroot: 465.5 GiB, 499842572288 bytes, 976255024 sectors
Units: sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 4096 bytes
I/O size (minimum/optimal): 4096 bytes / 4096 bytes
Disk /dev/sdc: 1.4 TiB, 1500301908480 bytes, 2930277165 sectors
Units: sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disklabel type: dos
Disk identifier: 0x445e51a8
And graysky: I thought I made the partition for /boot 250 MB and the encrypted partition 465.5 GB but I'm now quite sure I did something wrong...
Thank you all

Similar Messages

Updating Flash Player Does Not Reflect In Add-Ons Manager or Plug-In Check

The add-ons Manager shows I have Flashplayer version 11.3.300.265. The Plug-ins Check shows there is an update, and I downloaded and installed Flash Player version 11.3.300.268. Six times! Each time, the installation shows as successful on the Adobe site, but FF14 does not reflect the new version, and the Plug-in check continues to insist that the version is out of date.
I had no problems whatsoever updating to the latest Flashplayer version in IE (8). But FF is once again giving me trouble with this.
In addition, the add-ons manager shows a version of Flash 9.0.45.0, last updated Feb 20, 2007. There's a big red warning that it's out of date. This is in addition to Shockwave Flash (the correct one) and Shockwave for Director (which is current). It's been like this for awhile, and I disabled the antique version of Flash and it does not affect FF or Flashplayer performance.
I tried deleting my plug-ins database, but I just get all the same info when it is rebuilt. Any suggestions or solutions would be appreciated.

Such old version are usually located in the plugins folder in the Firefox program folder (C:\Program Files\Mozilla Firefox\).
You can enable the plugin and verify the path on the about:plugins page.
You can set the plugin.expose_full_path pref to true on the about:config page to see the full path of plugins on the about:plugins page.
*http://kb.mozillazine.org/Issues_related_to_plugins#Identifying_installed_plugins
*http://kb.mozillazine.org/about:plugins
*http://kb.mozillazine.org/about:config
It is best not to leave that pref set to true as it exposes that full path to web servers, so reset that pref to false after you are done with the about:plugins page.
See "Manually uninstalling a plugin":
*https://support.mozilla.org/kb/Troubleshooting+plugins

AR Down Payment Invoice Does Not Reflect in BP Master Data...

We have placed a sales order for a BP.
We select payment means and accept the payment
In the background a AP Down Payment Invoice is created
When we view the BP master data - the account ballance window does NOT reflect this "down payment"
If we select the golden arrow at account ballance, uncheck "reconciled transactions" you can see the payment and AP down payment and they clear each other out.
The problem is that when the final invoice is created it is not obvious that a down payment has been received. Even if you are simply working at the BP master data window, it is not obvious that a down payment has been received. I belive our process is correct because If you click the TDP box, the payment is listed and will be applied to the final invoice.
It simply does not alert the user that a payment had been received.
What are we doing wrong?????\
Thank you!
Edited by: Andrew Bleier on Feb 4, 2009 1:27 AM

Keith Taylor
You are right this feature is only available in Version 2007A. There account posting happen purely due to the pay SAP has been designed and the configuration of GL Accounts.
To make fundametal change to the core product is very difficult if you explain me your business process exactly as you do, I could think of alternatives.
Please let know.
Suda

Output error:the name of the package "greet" does not reflect the location of this file...

output error: The name of package 'greet' does not reflect the location of this file. Please change the package definition's name inside this file, or move the file. C:\Documents and Settings\Igal\My Documents\meiran\greet\Greeter.as
I keep on recieving this output error although my source path is set to C:\Documents and Settings\Igal\My Documents\meiran\greet.
any suggestions why this happens?

The classpaths you define in your Flash software tell the compiler where to look when it needs to find a class. According to your as file, the very top line indicates the Greeter.as file should be at a location specified by the path...
one-of-your-classpaths\com\example\quickstart\
So if one of your classpaths is: C:\Documents and Settings\Igal\My Documents\meiran\greet\
and you placed the file in the greet folder, then in your AS document you should not have the "com\example\quickstart" and your import statement in the fla should not be using that (should just be... import Greeter;)

Vendor listed in the batch does not reflect actual supplier.

Hi,
Vendor listed in the batch does not reflect actual supplier.
For some (STO's) it reflects the actual supplier & for some it is replaced by receving vendor.
Regards,
Sudakar

Great, that worked, thanks.
Now I have a small problem. I'm dispatching a MOVE event
manually at one point to force a listener to trigger, and it seems
that afterBounds is null. Here's how I'm dispatching the event:
nativeWindow.dispatchEvent(new
NativeWindowBoundsEvent('move'));
While the MOVE listener function is successfully called,
event.afterBounds.x throws a null reference exception.
Is there an easy workaround?

Query in MSS does not reflect selection on period

Hi group,
I have made a query in global area. In MSS I am calling the generated program from the query. This works fine. However, the selection on period in MSS does not reflect on the report. No matter what I choose, the report gives me the date period that I have set up in my variant in the background.
The selection screen for the report is the standard delivered with LDB PNPCE.
I have tried different date setup in my variant, but no matter what I do, I am not able to choose dynamically period from MSS.
Any help is appreciated
Kirsten

Solved this by saving the variant without passing values.

802.1x accounting does not reflect correct port status

Hi,
I've just discovered an issue when trying to use MSFT supplicant and Cisco 802.1x accounting. This makes 802.1x accounting completely unusable.
Facts:
1. MSFT supplicant does not send EAPOL-Logoff messages and there's no way to enable this (btw. Aegis client does not send it either, except when disabling interface).
2. I am doing machine authentication along with domain authentication.
3. Windows XP SP2 is used with EAP registry hacks applied.
4. PEAP/MS-CHAPv2 method is used.
Now when the computer is started it is logged into 802.1x with 'host/machine' account and RADIUS accounting start is sent by the switch. That's fine.
When a user logs on with its 'domain\user' identity, then EAPOL-Start is sent from the host triggering new EAP message exchange and the user is authenticated correctly. However the switch sends Interim Accounting still using 'host/machine' credentials which is obviously wrong.
Even more bizarre accounting happens when the user subsequently logs off from the machine. The EAPOL-Start is sent from the host triggering new authentication process for 'host/machine' identity and the host is authenticated ok. The accounting being sent is:
- first Accounting Stop for 'host/machine' User-Name
- then strange Interim Accounting with most attributes empty or missing
256970: Jul 10 15:56:41.211 MET-DST: RADIUS: authenticator 68 CA 1A 46 85 4F F5 95 - 87 B4 84 61 72 85 42 F3
256971: Jul 10 15:56:41.211 MET-DST: RADIUS: Acct-Session-Id [44] 10 "013F0000"
256972: Jul 10 15:56:41.211 MET-DST: RADIUS: Vendor, Cisco [26] 34
256973: Jul 10 15:56:41.211 MET-DST: RADIUS: Cisco AVpair [1] 28 "connect-progress=Auth Open"
256974: Jul 10 15:56:41.211 MET-DST: RADIUS: Acct-Session-Time [46] 6 0
256975: Jul 10 15:56:41.211 MET-DST: RADIUS: Acct-Input-Octets [42] 6 0
256976: Jul 10 15:56:41.211 MET-DST: RADIUS: Acct-Output-Octets [43] 6 0
256977: Jul 10 15:56:41.211 MET-DST: RADIUS: Acct-Input-Packets [47] 6 0
256978: Jul 10 15:56:41.211 MET-DST: RADIUS: Acct-Output-Packets [48] 6 0
256979: Jul 10 15:56:41.211 MET-DST: RADIUS: Acct-Authentic [45] 6 RADIUS [1]
256980: Jul 10 15:56:41.211 MET-DST: RADIUS: Acct-Status-Type [40] 6 Watchdog [3]
256981: Jul 10 15:56:41.211 MET-DST: RADIUS: Vendor, Cisco [26] 24
256982: Jul 10 15:56:41.211 MET-DST: RADIUS: cisco-nas-port [2] 18 "FastEthernet0/11"
256983: Jul 10 15:56:41.211 MET-DST: RADIUS: NAS-Port [5] 6 50011
256984: Jul 10 15:56:41.211 MET-DST: RADIUS: NAS-Port-Type [61] 6 Eth [15]
256985: Jul 10 15:56:41.211 MET-DST: RADIUS: Class [25] 27
256986: Jul 10 15:56:41.215 MET-DST: RADIUS: 43 41 43 53 3A 30 2F 32 39 32 66 2F 61 38 31 38 [CACS:0/292f/a818]
256987: Jul 10 15:56:41.215 MET-DST: RADIUS: 30 32 38 2F 35 30 30 31 31 [028/50011]
256988: Jul 10 15:56:41.215 MET-DST: RADIUS: Service-Type [6] 6 Framed [2]
256989: Jul 10 15:56:41.215 MET-DST: RADIUS: NAS-IP-Address [4] 6 10.129.128.40
256990: Jul 10 15:56:41.215 MET-DST: RADIUS: Acct-Delay-Time [41] 6 0
256991: Jul 10 15:56:41.239 MET-DST: RADIUS: Received from id 1646/238 10.129.128.38:1813, Accounting-response, len 20
256992: Jul 10 15:56:41.239 MET-DST: RADIUS: authenticator ED 8E 8B 15 28 5F E4 37 - BF A8 F5 9E 10 43 5E A8
So that the accounting sent from the switch does not reflect current status of the authenticated user on a given port.
How to deal with this issue? Any ideas?
thanks,
robert

Does your radius proxy-table is populated wrong for EAP- SIM users ?

Net Price does not reflect on Consignment PO even after maintaining info re

Dear Experts,
I have created consignment PO but the net price does not reflect on it. I have already maintained valid consignment info record for this material with reference to standard purchasing organization in ME11.
Would appreciate your views ...
Cheers !
Sachin Narvekar

Hi,
the system behaviour is correct here.
The basic concept of vendor consignment lies in this.
In this case PO is a request to put his stocks at the company.
The moment we uses( Transfer from vendor stock to Company's own stock, using 411, or direct issue to cost centres using 201K) this stock, liability will be generated.
Then the price from the info record will be used as well as the tax code.
Then u can run a settlement transation , for payment settlements.
Until the moment u uses the stock, it will be vendors stock only, thats why only Issue create liability.
So the system behaviour is correct.
Regards
Krishna

Business area does not reflecting in IT 0001

Dear Expert,
I have assign cost center to organization unit, then hire employee through PA40, so position assign into IT0001,
system pick up the cost center but does not reflecting the business area in infotype 0001.
i checked with FI consultant, there is proper intergation between cost center and business area.
Please tell me, how to resolved this issue.
Many Many Thanks
Urvashi

Hi Urvashi,
You will get the Default values for Company code, Personal area, Personal Sub Area and Business Area because of Account assignment infotype - IT1008 - for your position or Org Unit
check from PO10 or PO13 and infotype 1008.
You will have PA value defaulted on IT 0000 screen and others defaulted on IT 0001 screen.
You can change these values on respective screens. A warning will be issued but you can overwrite them.
Regards,
HARANATH

My WishList does not reflect current purchases

Ever since transferring my iTunes library from my PC to iMac, I have noticed that My WishList in iTunes store, while it lists all the previously "wished for" apps and songs, does not reflect which ones I have purchased. In other words, it used to be that the purchased apps were listed, and instead of a price it would just say "purchased." Now it just shows a price, as if I never purchased the app. Even when I open the app description in the itunes store, the price remains, as if I never purchased it. I have occasionally seen this happen when the iTunes store account took time to refresh the information it had, but this has been going on for several weeks.
Is there someway to "remind" my iTunes account of what purchases I have, so that my purchase history is correctly reflected? I've been using the same account the whole time, so I know that is not the problem.

Where did it show as a portable device? If in My Computer try:
Removing and reinstalling iTunes, QuickTime, and other software components for Windows Vista or Windows 7
iTunes: Syncing media content to iOS devices and iPod

Solved yet it does not appear to be so, when looking at the Category

Hello : )
This topic "Missing content - what's happening here?" in Safari.
http://discussions.apple.com/thread.jspa?threadID=652524&tstart=0
Is indeed Solved yet it does not appear to be so when looking at it in the Safari category. Little software bug ?
http://discussions.apple.com/category.jspa?categoryID=169
Thank you.
Eme

Hello Ali,
Many thanks for the reply. The OP speaks of marking it solved first and making the helpful stars disappear, but the helpful are there. so I just wondered.
http://discussions.apple.com/message.jspa?messageID=3164852#3164852
Yes, I realize the helpful & the solved stars will remain if then marked
not answered.
Thank you.
Eme;~[)

Compiled CHM File Does Not Reflect New Project Name

I have read many of the experts' responses to posts and found them extremely helpful. However, I have not seen one that addresses my issue.
I have RH HTML Version RH8. I renamed a project via 1) File - Rename Project and 2) Single Source Layouts - Primary Layout - Properties - Output Folder and File Name.
Two problems are: 1) The Project Folder name still reflects the old project name and 2) The CHM file still reflects the old project name.
As a result, the output Help that the user sees still has the old project name in the title bar.
All generated files as well as the RoboHelpHTML Project File were changed to the new project name, just as the RENAME PROJECTS Help says it should. However, the CHM file does not reflect the new project name as it says it should.
1) Can I change the Folder name that was created when I compiled the Help file to the correct name?
2) Can I change the FILENAME in the SELECT OUTPUT FOLDER AND FILENAME window?
3) Can I / should I rename the TOC and Index filenames from the old project name to the new project name? (Help says that changing the project name does not change these file names and it didn't.)
Will any of these actions correct the problem? I appreciate any help you can give.

Welcome to our community
Try File > Project Settings.
And if that doesn't get it, try the Project Set-up pod, windows and change the Window Caption.
Cheers... Rick
Helpful and Handy Links
RoboHelp Wish Form/Bug Reporting Form
Begin learning RoboHelp HTML 7, 8 or 9 within the day!
Adobe Certified RoboHelp HTML Training
SorcerStone Blog
RoboHelp eBooks

IPone 6, iOs 8.1.2 when removing the phone from the charging does not reflect the increase in the percent charge level , by reconnecting displays correctly

when removing the phone from the charging does not reflect the increase in the percent charge level , by reconnecting displays correctly

Addendum
Last night charging for around 3-4 hours only charged a dead phone by 55% then left it to charge overnight
Today the battery dropped from 6:15 am full charge to 53% at 10:38 am at time of writing this with
1 phone call out for 30 secs
1 incoming missed call,
Whatsapp fetched around 10 msgs
Email fetched around 20 ermail from 4 accounts but not viewed yet on phone

Itunes does not reflect Books purchased

I have purchased books over a year ago using my iPad 2. I can't see in Itunes books purchased over a year ago. When syncing Ipad to ITunes Books library does not reflect the books purchased, Why? Does anyone know?
Thank you.
Jaime

Hey there Fritzme,
It sounds like you are unable to download book purchases you made over a year ago. If you haven't already, I would check your purchased history with this article to see if you can find them there:
iTunes Store: See your purchase history and web order numbers
http://support.apple.com/kb/ht2727
If you see them there but cannot find them to redownload using the iBooks app, they may have been hidden and can be unhidden using this article:
iTunes Store: Hiding and unhiding purchases
http://support.apple.com/kb/ht4919
If you cannot find it there either, then per the first article you may need to contact the iTunes Store support directly:
For help with an older purchase, contact iTunes Store support and select Purchases, Billing, and Redemption
Thank you for using Apple Support Communities.
All the very best,
Sterling

I have inserted an image into my form that does not reflect when i save it a a pdf

I have insetred an image into my form that does not reflect when i save it as a pdf - please cna you assist?

Hi leannedatel,
There was a possible answer to this posted previously. Try this thread for a solution:
http://forums.adobe.com/docs/DOC-4144
Cheers!

[SOLVED] df -h does not reflect true root filesystem size

Similar Messages

Maybe you are looking for