[Solved] Lost sound with xMonad
Hello,
I lost the sound when I run xMonad. When I run gnome everything works fine. Someone from the xMonad mailing list said I must be forgetting to start alsa or pulseaudio daemons. How do I do that?
Thanks!
Last edited by eskatrem (2012-07-16 19:33:49)
I ran alsamizer and turned the volume to maximum for everything.
EDIT: I set myself in the audio group, but still unable to get any sound
speaker-test does this (before I interrupt it, it seems to do something forever):
speaker-test 1.0.25
Playback device is default
Stream parameters are 48000Hz, S16_LE, 1 channels
Using 16 octaves of pink noise
Rate set to 48000Hz (requested 48000Hz)
Buffer size range from 2048 to 16384
Period size range from 1024 to 1024
Using max buffer size 16384
Periods = 4
was set period_size = 1024
was set buffer_size = 16384
0 - Front Left
Time per period = 2.665351
0 - Front Left
Time per period = 2.986627
0 - Front Left
Time per period = 2.986616
0 - Front Left
Time per period = 2.986630
0 - Front Left
Last edited by eskatrem (2012-07-16 14:19:41)
Similar Messages
-
[SOLVED]No Sound with ALSA - Intel Corporation 82801G HD Audio
Hey all,
I've succesfully installed Arch Linux. My past two attempts have met with failure, all because of my own failure to read and follow directions correctly. This time everything is installed correctly. I am running Kdemod3 on my laptop with Arch and everything works great. I LOVE Pacman and the simplicity of Arch's configuration files. It's super fast and all together simple. My only remaining problem is this:
My sound with ALSA is not functioning. I followed the installation instructions at the arch wiki and after unmuting all of my channels I still would not get any sound. My sound module is snd_hda_intel and it is detected, loaded and the whole nine yards (as far as I can tell). My user is a member of the 'audio' user group also. I looked at the troubleshooting tips on the bottom of the Wiki but decided not to try them as they do not seem to pertain to my card (snd_hda_intel) but I will try them if anyone would like me to.
If anyone has any ideas, they'd be greatly appreciated!:D Anything I can provide that you need I will be more than willing to provide.
Thanks for such a great distribution,
Dan
Last edited by JazzDan (2008-06-29 05:06:35)Problem resolved. I ran alsaconf, selected my soundcard, and everything was working from there out. Thanks MisfitI38 on the IRC!!!
-
I'm getting no sound with vmware, not sure why
Here's what I've been trying to test things:
$ cat /dev/urandom | aplay
Playing raw data 'stdin' : Unsigned 8 bit, Rate 8000 Hz, Mono
Here's some alsa info, if it helps:
$ aplay -L
null
Discard all samples (playback) or generate zero samples (capture)
default:CARD=AudioPCI
Ensoniq AudioPCI, ES1371 DAC2/ADC
Default Audio Device
sysdefault:CARD=AudioPCI
Ensoniq AudioPCI, ES1371 DAC2/ADC
Default Audio Device
front:CARD=AudioPCI,DEV=0
Ensoniq AudioPCI, ES1371 DAC2/ADC
Front speakers
rear:CARD=AudioPCI,DEV=0
Ensoniq AudioPCI, ES1371 DAC1
Rear speakers
surround40:CARD=AudioPCI,DEV=0
Ensoniq AudioPCI, ES1371 DAC2/ADC
4.0 Surround output to Front and Rear speakers
iec958:CARD=AudioPCI,DEV=0
Ensoniq AudioPCI, ES1371 DAC2/ADC
IEC958 (S/PDIF) Digital Audio Output
Last edited by specular (2014-08-27 19:52:45)Don't think I was clear enough, but arch is installed as a vmware guest. Below is the requested output from the alsa-info script:
upload=true&script=true&cardinfo=
!!ALSA Information Script v 0.4.63
!!Script ran on: Wed Aug 27 18:29:05 UTC 2014
!!Linux Distribution
NAME="Arch Linux" ID=arch PRETTY_NAME="Arch Linux" HOME_URL="https://www.archlinux.org/" SUPPORT_URL="https://bbs.archlinux.org/" BUG_REPORT_URL="https://bugs.archlinux.org/"
!!DMI Information
Manufacturer: VMware, Inc.
Product Name: VMware7,1
Product Version: None
Firmware Version: VMW71.00V.0.B64.1310020058
!!Kernel Information
Kernel release: 3.14.2-1-ARCH
Operating System: GNU/Linux
Architecture: x86_64
Processor: unknown
SMP Enabled: Yes
!!ALSA Version
Driver version: k3.14.2-1-ARCH
Library version: 1.0.27.2
Utilities version: 1.0.28
!!Loaded ALSA modules
snd_ens1371
!!Sound Servers on this system
No sound servers found.
!!Soundcards recognised by ALSA
0 [AudioPCI ]: ENS1371 - Ensoniq AudioPCI
Ensoniq AudioPCI ENS1371 at 0x1000, irq 19
!!PCI Soundcards installed in the system
02:01.0 Multimedia audio controller: Ensoniq ES1371 [AudioPCI-97] (rev 02)
!!Advanced information - PCI Vendor/Device/Subsystem ID's
02:01.0 0401: 1274:1371 (rev 02)
Subsystem: 1274:1371
!!Loaded sound module options
!!Module: snd_ens1371
enable : Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y
id : (null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null)
index : -1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1
joystick_port : 0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0
lineio : 0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0
spdif : 0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0
!!AC97 Codec information
--startcollapse--
0-0/0: Cirrus Logic CS4297A rev 3
PCI Subsys Vendor: 0x1274
PCI Subsys Device: 0x1371
Flags: 4
Capabilities :
DAC resolution : 16-bit
ADC resolution : 16-bit
3D enhancement : No 3D Stereo Enhancement
Current setup
Mic gain : +0dB [+0dB]
POP path : pre 3D
Sim. stereo : off
3D enhancement : off
Loudness : off
Mono output : MIX
Mic select : Mic1
ADC/DAC loopback : off
0:00 = 0000
0:02 = 0e8e
0:04 = 0000
0:06 = 0000
0:08 = 0000
0:0a = 0000
0:0c = bfbf
0:0e = bfbf
0:10 = bfbf
0:12 = bfbf
0:14 = bfbf
0:16 = bfbf
0:18 = 28a8
0:1a = 0000
0:1c = 0808
0:1e = 0000
0:20 = 0000
0:22 = 0000
0:24 = 0000
0:26 = 000f
0:28 = 0000
0:2a = 0000
0:2c = 0000
0:2e = 0000
0:30 = 0000
0:32 = 0000
0:34 = 0000
0:36 = 0000
0:38 = 0000
0:3a = 0000
0:3c = 0000
0:3e = 0000
0:40 = 0000
0:42 = 0000
0:44 = 0000
0:46 = 0000
0:48 = 0000
0:4a = 0000
0:4c = 0000
0:4e = 0000
0:50 = 0000
0:52 = 0000
0:54 = 0000
0:56 = 0000
0:58 = 0000
0:5a = 0000
0:5c = 0000
0:5e = 0000
0:60 = 0000
0:62 = 0000
0:64 = 0000
0:66 = 0000
0:68 = 0000
0:6a = 0000
0:6c = 0000
0:6e = 0000
0:70 = 0000
0:72 = 0000
0:74 = 0000
0:76 = 0000
0:78 = 0000
0:7a = 0000
0:7c = 4352
0:7e = 5913
--endcollapse--
!!ALSA Device nodes
crw-rw----+ 1 root audio 116, 6 Aug 28 01:35 /dev/snd/controlC0
crw-rw----+ 1 root audio 116, 2 Aug 28 01:35 /dev/snd/midiC0D0
crw-rw----+ 1 root audio 116, 5 Aug 28 01:35 /dev/snd/pcmC0D0c
crw-rw----+ 1 root audio 116, 4 Aug 28 03:28 /dev/snd/pcmC0D0p
crw-rw----+ 1 root audio 116, 3 Aug 28 01:35 /dev/snd/pcmC0D1p
crw-rw----+ 1 root audio 116, 1 Aug 28 01:35 /dev/snd/seq
crw-rw----+ 1 root audio 116, 33 Aug 28 01:35 /dev/snd/timer
/dev/snd/by-path:
total 0
drwxr-xr-x 2 root root 60 Aug 28 01:35 .
drwxr-xr-x 3 root root 200 Aug 28 01:35 ..
lrwxrwxrwx 1 root root 12 Aug 28 01:35 pci-0000:02:01.0 -> ../controlC0
!!Aplay/Arecord output
APLAY
**** List of PLAYBACK Hardware Devices ****
card 0: AudioPCI [Ensoniq AudioPCI], device 0: ES1371/1 [ES1371 DAC2/ADC]
Subdevices: 1/1
Subdevice #0: subdevice #0
card 0: AudioPCI [Ensoniq AudioPCI], device 1: ES1371/2 [ES1371 DAC1]
Subdevices: 1/1
Subdevice #0: subdevice #0
ARECORD
**** List of CAPTURE Hardware Devices ****
card 0: AudioPCI [Ensoniq AudioPCI], device 0: ES1371/1 [ES1371 DAC2/ADC]
Subdevices: 1/1
Subdevice #0: subdevice #0
!!Amixer output
!!-------Mixer controls for card 0 [AudioPCI]
Card hw:0 'AudioPCI'/'Ensoniq AudioPCI ENS1371 at 0x1000, irq 19'
Mixer name : 'Cirrus Logic CS4297A rev 3'
Components : 'AC97a:43525913'
Controls : 26
Simple ctrls : 13
Simple mixer control 'Master',0
Capabilities: pvolume pswitch pswitch-joined
Playback channels: Front Left - Front Right
Limits: Playback 0 - 63
Mono:
Front Left: Playback 49 [78%] [-21.00dB] [on]
Front Right: Playback 49 [78%] [-21.00dB] [on]
Simple mixer control 'PCM',0
Capabilities: pvolume pswitch pswitch-joined
Playback channels: Front Left - Front Right
Limits: Playback 0 - 63
Mono:
Front Left: Playback 23 [37%] [0.00dB] [on]
Front Right: Playback 23 [37%] [0.00dB] [on]
Simple mixer control 'Line',0
Capabilities: pvolume pswitch pswitch-joined cswitch cswitch-exclusive
Capture exclusive group: 0
Playback channels: Front Left - Front Right
Capture channels: Front Left - Front Right
Limits: Playback 0 - 63
Front Left: Playback 0 [0%] [-34.50dB] [off] Capture [off]
Front Right: Playback 0 [0%] [-34.50dB] [off] Capture [off]
Simple mixer control 'CD',0
Capabilities: pvolume pswitch pswitch-joined cswitch cswitch-exclusive
Capture exclusive group: 0
Playback channels: Front Left - Front Right
Capture channels: Front Left - Front Right
Limits: Playback 0 - 63
Front Left: Playback 0 [0%] [-34.50dB] [off] Capture [off]
Front Right: Playback 0 [0%] [-34.50dB] [off] Capture [off]
Simple mixer control 'Mic',0
Capabilities: pvolume pswitch pswitch-joined cswitch cswitch-exclusive
Capture exclusive group: 0
Playback channels: Front Left - Front Right
Capture channels: Front Left - Front Right
Limits: Playback 0 - 63
Front Left: Playback 0 [0%] [-34.50dB] [off] Capture [on]
Front Right: Playback 0 [0%] [-34.50dB] [off] Capture [on]
Simple mixer control 'Mic Boost (+20dB)',0
Capabilities: pswitch pswitch-joined
Playback channels: Mono
Mono: Playback [off]
Simple mixer control 'Video',0
Capabilities: pvolume pswitch pswitch-joined cswitch cswitch-exclusive
Capture exclusive group: 0
Playback channels: Front Left - Front Right
Capture channels: Front Left - Front Right
Limits: Playback 0 - 63
Front Left: Playback 0 [0%] [-34.50dB] [off] Capture [off]
Front Right: Playback 0 [0%] [-34.50dB] [off] Capture [off]
Simple mixer control 'Phone',0
Capabilities: pvolume pswitch pswitch-joined cswitch cswitch-exclusive
Capture exclusive group: 0
Playback channels: Front Left - Front Right
Capture channels: Front Left - Front Right
Limits: Playback 0 - 63
Front Left: Playback 0 [0%] [-34.50dB] [off] Capture [off]
Front Right: Playback 0 [0%] [-34.50dB] [off] Capture [off]
Simple mixer control 'IEC958',0
Capabilities: pswitch pswitch-joined
Playback channels: Mono
Mono: Playback [off]
Simple mixer control 'Aux',0
Capabilities: pvolume pswitch pswitch-joined cswitch cswitch-exclusive
Capture exclusive group: 0
Playback channels: Front Left - Front Right
Capture channels: Front Left - Front Right
Limits: Playback 0 - 63
Front Left: Playback 0 [0%] [-34.50dB] [off] Capture [off]
Front Right: Playback 0 [0%] [-34.50dB] [off] Capture [off]
Simple mixer control 'Capture',0
Capabilities: cvolume cswitch cswitch-joined
Capture channels: Front Left - Front Right
Limits: Capture 0 - 15
Front Left: Capture 8 [53%] [12.00dB] [on]
Front Right: Capture 8 [53%] [12.00dB] [on]
Simple mixer control 'Mix',0
Capabilities: cswitch cswitch-exclusive
Capture exclusive group: 0
Capture channels: Front Left - Front Right
Front Left: Capture [off]
Front Right: Capture [off]
Simple mixer control 'Mix Mono',0
Capabilities: cswitch cswitch-exclusive
Capture exclusive group: 0
Capture channels: Front Left - Front Right
Front Left: Capture [off]
Front Right: Capture [off]
!!Alsactl output
--startcollapse--
state.AudioPCI {
control.1 {
iface MIXER
name 'Master Playback Switch'
value true
comment {
access 'read write'
type BOOLEAN
count 1
control.2 {
iface MIXER
name 'Master Playback Volume'
value.0 49
value.1 49
comment {
access 'read write'
type INTEGER
count 2
range '0 - 63'
dbmin -9450
dbmax 0
dbvalue.0 -2100
dbvalue.1 -2100
control.3 {
iface MIXER
name 'Phone Playback Switch'
value false
comment {
access 'read write'
type BOOLEAN
count 1
control.4 {
iface MIXER
name 'Phone Playback Volume'
value.0 0
value.1 0
comment {
access 'read write'
type INTEGER
count 2
range '0 - 63'
dbmin -3450
dbmax 6000
dbvalue.0 -3450
dbvalue.1 -3450
control.5 {
iface MIXER
name 'Mic Playback Switch'
value false
comment {
access 'read write'
type BOOLEAN
count 1
control.6 {
iface MIXER
name 'Mic Playback Volume'
value.0 0
value.1 0
comment {
access 'read write'
type INTEGER
count 2
range '0 - 63'
dbmin -3450
dbmax 6000
dbvalue.0 -3450
dbvalue.1 -3450
control.7 {
iface MIXER
name 'Mic Boost (+20dB)'
value false
comment {
access 'read write'
type BOOLEAN
count 1
control.8 {
iface MIXER
name 'Line Playback Switch'
value false
comment {
access 'read write'
type BOOLEAN
count 1
control.9 {
iface MIXER
name 'Line Playback Volume'
value.0 0
value.1 0
comment {
access 'read write'
type INTEGER
count 2
range '0 - 63'
dbmin -3450
dbmax 6000
dbvalue.0 -3450
dbvalue.1 -3450
control.10 {
iface MIXER
name 'CD Playback Switch'
value false
comment {
access 'read write'
type BOOLEAN
count 1
control.11 {
iface MIXER
name 'CD Playback Volume'
value.0 0
value.1 0
comment {
access 'read write'
type INTEGER
count 2
range '0 - 63'
dbmin -3450
dbmax 6000
dbvalue.0 -3450
dbvalue.1 -3450
control.12 {
iface MIXER
name 'Video Playback Switch'
value false
comment {
access 'read write'
type BOOLEAN
count 1
control.13 {
iface MIXER
name 'Video Playback Volume'
value.0 0
value.1 0
comment {
access 'read write'
type INTEGER
count 2
range '0 - 63'
dbmin -3450
dbmax 6000
dbvalue.0 -3450
dbvalue.1 -3450
control.14 {
iface MIXER
name 'Aux Playback Switch'
value false
comment {
access 'read write'
type BOOLEAN
count 1
control.15 {
iface MIXER
name 'Aux Playback Volume'
value.0 0
value.1 0
comment {
access 'read write'
type INTEGER
count 2
range '0 - 63'
dbmin -3450
dbmax 6000
dbvalue.0 -3450
dbvalue.1 -3450
control.16 {
iface MIXER
name 'PCM Playback Switch'
value true
comment {
access 'read write'
type BOOLEAN
count 1
control.17 {
iface MIXER
name 'PCM Playback Volume'
value.0 23
value.1 23
comment {
access 'read write'
type INTEGER
count 2
range '0 - 63'
dbmin -3450
dbmax 6000
dbvalue.0 0
dbvalue.1 0
control.18 {
iface MIXER
name 'Capture Source'
value.0 Mic
value.1 Mic
comment {
access 'read write'
type ENUMERATED
count 2
item.0 Mic
item.1 CD
item.2 Video
item.3 Aux
item.4 Line
item.5 Mix
item.6 'Mix Mono'
item.7 Phone
control.19 {
iface MIXER
name 'Capture Switch'
value true
comment {
access 'read write'
type BOOLEAN
count 1
control.20 {
iface MIXER
name 'Capture Volume'
value.0 8
value.1 8
comment {
access 'read write'
type INTEGER
count 2
range '0 - 15'
dbmin 0
dbmax 2250
dbvalue.0 1200
dbvalue.1 1200
control.21 {
iface MIXER
name 'IEC958 Playback Con Mask'
value '0fff000f00000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000'
comment {
access read
type IEC958
count 1
control.22 {
iface MIXER
name 'IEC958 Playback Pro Mask'
value cf00000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000
comment {
access read
type IEC958
count 1
control.23 {
iface MIXER
name 'IEC958 Playback Default'
value '0082000200000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000'
comment {
access 'read write'
type IEC958
count 1
control.24 {
iface MIXER
name 'IEC958 Playback Switch'
value false
comment {
access 'read write'
type BOOLEAN
count 1
control.25 {
iface PCM
name 'Playback Channel Map'
value.0 0
value.1 0
comment {
access read
type INTEGER
count 2
range '0 - 36'
control.26 {
iface PCM
device 1
name 'Playback Channel Map'
value.0 0
value.1 0
comment {
access read
type INTEGER
count 2
range '0 - 36'
--endcollapse--
!!All Loaded Modules
Module
fuse
vmw_vsock_vmci_transport
vsock
nls_iso8859_1
nls_cp437
vfat
fat
coretemp
hwmon
joydev
snd_ens1371
mousedev
snd_ac97_codec
hid_generic
ac97_bus
gameport
snd_rawmidi
snd_seq_device
snd_pcm
snd_timer
snd
crct10dif_pclmul
crc32_pclmul
crc32c_intel
ghash_clmulni_intel
soundcore
usbhid
aesni_intel
aes_x86_64
lrw
gf128mul
glue_helper
hid
psmouse
vmwgfx
ppdev
ablk_helper
cryptd
evdev
vmxnet3
mac_hid
pcspkr
vmw_balloon
i2c_piix4
serio_raw
ttm
microcode
drm
processor
i2c_core
intel_agp
intel_gtt
vmw_vmci
parport_pc
parport
battery
shpchp
ac
button
ext4
crc16
mbcache
jbd2
dm_mod
sd_mod
crc_t10dif
crct10dif_common
sr_mod
cdrom
ata_generic
pata_acpi
atkbd
libps2
ata_piix
libata
mptsas
scsi_transport_sas
mptscsih
uhci_hcd
ehci_pci
scsi_mod
ehci_hcd
usbcore
mptbase
usb_common
floppy
i8042
serio
!!ALSA/HDA dmesg
[ 5.342713] mousedev: PS/2 mouse device common for all mice
[ 5.345140] snd_ens1371 0000:02:01.0: enabling device (0000 -> 0001)
[ 5.391722] intel_rapl: domain package energy ctr 0:0 not working, skip
Last edited by specular (2014-08-27 18:45:55) -
[SOLVED] No sound (with flash)
Hello.
I have no sound with flash. It does work elsewhere.
I am using ALSA.
My flash should output audio correctly according to wiki: https://wiki.archlinux.org/index.php/Fl … d_in_Flash
# aplay -l
**** List of PLAYBACK Hardware Devices ****
card 0: PCH [HDA Intel PCH], device 0: ALC889 Analog [ALC889 Analog]
Subdevices: 1/1
Subdevice #0: subdevice #0
card 0: PCH [HDA Intel PCH], device 1: ALC889 Digital [ALC889 Digital]
Subdevices: 1/1
Subdevice #0: subdevice #0
card 1: Generic [HD-Audio Generic], device 3: HDMI 0 [HDMI 0]
Subdevices: 1/1
Subdevice #0: subdevice #0
EDIT: I'm retarded. I didn't add my user to audio group. And sound elsewhere was from speaker-test which needs SU.
Last edited by handl3r (2012-01-22 07:39:34)codemac wrote:
Orrrr it's because the flash plugin uses OSS.
run `aoss firefox` and be happy.
OSS does still work or at least the alsa backwards compatibility layer that emulates the old interfaces, right? did i miss anything?
for newer versions of flash (like version 9) simply install firefox in wine and let it install the plugin. that usually works great! -
[SOLVED] Lost Sound After Upgrade
Solved (for now at least). The problem appears to be a bug with alsa. Alsaconf writes a file called /etc/modprobe.d/50-sound.conf, which contains the aliases for the sound card. But for some reason it then wasn't reading the file. Copying the alias entries to /etc/modprobe.d/modprobe.conf to read directly from there seems to have worked.
Now to fix the frequency scaling.
===================== solved ===========================
I lost all sound after the last upgrade. I just rebooted because frequency scaling is also not working, and no sound.
all drivers seem to be there:
08:50 AM:~ $ lsmod |grep snd
snd_mpu401_uart 9264 0
snd_hda_codec_realtek 278132 1
snd_cs46xx 96800 1
snd_seq_dummy 3540 0
gameport 13760 2 snd_cs46xx
snd_hda_intel 31208 3
snd_hda_codec 82128 2 snd_hda_codec_realtek,snd_hda_intel
snd_hwdep 9976 1 snd_hda_codec
snd_rawmidi 26592 2 snd_mpu401_uart,snd_cs46xx
snd_ac97_codec 133560 1 snd_cs46xx
snd_seq_oss 36224 0
snd_seq_midi_event 8592 1 snd_seq_oss
snd_seq 64640 5 snd_seq_dummy,snd_seq_oss,snd_seq_midi_event
snd_seq_device 8324 4 snd_seq_dummy,snd_rawmidi,snd_seq_oss,snd_seq
snd_pcm_oss 47328 0
snd_pcm 90872 5 snd_cs46xx,snd_hda_intel,snd_hda_codec,snd_ac97_codec,snd_pcm_oss
snd_timer 25344 2 snd_seq,snd_pcm
snd_page_alloc 10784 3 snd_cs46xx,snd_hda_intel,snd_pcm
snd_mixer_oss 20976 2 snd_pcm_oss
snd 76744 21 snd_mpu401_uart,snd_hda_codec_realtek,snd_cs46xx,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_rawmidi,snd_ac97_codec,snd_seq_oss,snd_seq,snd_seq_device,snd_pcm_oss,snd_pcm,snd_timer,snd_mixer_oss
soundcore 8576 2 snd
ac97_bus 2160 1 snd_ac97_codec
I don't see anything in the updated packages that might cause this:
[2009-08-09 18:09] upgraded gawk (3.1.6-3 -> 3.1.7-1)
[2009-08-09 18:09] upgraded gimp (2.6.6-2 -> 2.6.6-3)
[2009-08-09 18:09] upgraded imagemagick (6.5.4.5-1 -> 6.5.4.8-1)
[2009-08-09 18:09] upgraded kdelibs3 (3.5.10-5 -> 3.5.10-7)
[2009-08-09 18:09] upgraded mkinitcpio (0.5.25-1 -> 0.5.26-1)
[2009-08-09 18:09] upgraded polkit-qt (0.9.2-1 -> 0.9.2-2)
[2009-08-09 18:09] upgraded psmisc (22.7-1 -> 22.8-1)
[2009-08-09 18:09] upgraded python-pygame (1.9.0-1 -> 1.9.1-1)
[2009-08-09 18:09] upgraded python-pysqlite (2.4.1-2 -> 2.5.5-1)
[2009-08-09 18:09] upgraded readline (6.0.003-3 -> 6.0.004-1)
[2009-08-09 18:09] Fixing gshadow file ...
[2009-08-09 18:09] upgraded shadow (4.1.4.1-1 -> 4.1.4.2-1)
I tried firefox, xine, mythfrontend, avidemux2, xmms and mpg123 - there's no sound in any app. If I play something where there are indicators, like in xmms, the eq indicator levels jump, the song progresses like it's playing, but no sound. I reran alsaconf, it seems to be configured properly. The mixer sliders work and aren't muted. It doesn't work either as root or as user.
I have another computer hooked up through the line out and the sound still works fine there, so it doesn't appear to be a hardware problem.
I'm completely stumped at this point. If it's a bug somewhere, what's it a bug in to cause global sound loss? Is there anything else I'm overlooking? All I can think is that it must be muted somewhere, but I can't find it. Or else it has something to do with the cpu and cpu freq scaling that's also broken now.
===================== solved ===========================
Last edited by userlander (2009-08-10 15:04:45)Try this - Reset the iPad by holding down on the Sleep and Home buttons at the same time for about 10-15 seconds until the Apple Logo appears - ignore the red slider - let go of the buttons. (This is equivalent to rebooting your computer.)
Check your settings. The iPads have a small switch on the right edge. It can be used as a rotation lock to keep the screen from automatically reorienting itself as you move around, but you need to have the tablet’s settings configured properly. That same switch, right above the volume buttons, can also be set to function instead as a mute button to silence certain types of audio.
If the switch is set to work as a mute button, you can change its purpose to “screen-rotation lock” by tapping the Settings icon on the home screen. On the Settings screen, tap General on the left side, and on the right side of the screen flick down to “Use Side Switch to.” Tap to select Lock Rotation or Mute to set the button’s function. Even if you set the side switch for your preferred use, you can still mute the Mini or lock the screen. Just double-click the Home button, and when the panel of apps appears along the bottom edge of the screen, flick the row from left to right with your finger. Tap the icon on the far left side of the row to either lock the iPad’s screen or mute the iPad’s alerts, notifications and sound effects. Music, podcasts and video are not muted unless you turn the volume all the way down.
iPhone: Can't hear through the receiver or speakers
http://support.apple.com/kb/ts1630
http://www.atreks.com/app-no-sound-on-ipad-4-%E2%80%93-what-to-do/
Cheers, Tom -
[solved] no sound with multimedia apps using Pulseaudio Dummy drive
It seems audio issues are kindof frequent atm, but I couldn't solve the strange issue using the informations provided in the threads nor the wiki
Issue:
One app plays audio just fine: Deadbeef Audio player, but no activity shows up in Pavucontrol while playing.
Deadbeef uses default Alsa outpput (currently Pulse audio server)
The other multimedia that I use or tried (mplayer, VLC and paplay test.wav) play files with no sound to be heard. Pavucontrol just shows 'dummy output' activity
as for mplayer that is the case with default pulse and alsa audio drivers
Context:
1/ Recently switched from ALSA to PulseAudio
Have no ~/.asoundrc
2/ First appeared when:
Installed software updates last week. I lazily hoped it will resolve itself with the next update which it didn't so far. None of the packets I updated had linux|pulse|alsa|sound|audio in its name.
Another issue appeared at the same time: no software is able to play any media from the DVD drive. The optical drive itself is well recognized whether by 'lsscsi' or /proc/sys/dev/cdrom/info
3/ PulseAudio did not start today after booting the system
$ pulseaudio --start
E: [pulseaudio] main.c: daemon startup failed
Started OK after commenting "/etc/pulse/default.pa" config line that remap microphone to mono for Skype (as per the Pulseaudio wiki)
System Audio info:
$ cat /proc/asound/cards
0 [PCH ]: HDA-Intel - HDA Intel PCH
HDA Intel PCH at 0xf7d00000 irq 46
$ lspci|grep -i audio
00:1b.0 Audio device: Intel Corporation 7 Series/C210 Series Chipset Family High Definition Audio Controller (rev 04)
$ aplay -l
carte 0: PCH [HDA Intel PCH], périphérique 0: ALC892 Analog [ALC892 Analog]
Sous-périphériques: 1/1
Sous-périphérique #0: subdevice #0
carte 0: PCH [HDA Intel PCH], périphérique 1: ALC892 Digital [ALC892 Digital]
Sous-périphériques: 1/1
Sous-périphérique #0: subdevice #0
# fuser -v /dev/snd/*
/dev/snd/controlC0: kozaki 20121 F.... pulseaudio
$ cat /proc/asound/modules;
0 snd_hda_intel
$ lsmod | grep ^snd;
snd_hda_codec_realtek 67127 1
snd_hda_codec_generic 63126 1 snd_hda_codec_realtek
snd_hda_intel 26327 3
snd_hda_controller 26727 1 snd_hda_intel
snd_hda_codec 108552 4 snd_hda_codec_realtek,snd_hda_codec_generic,snd_hda_intel,snd_hda_controller
snd_hwdep 17244 1 snd_hda_codec
snd_pcm 88487 3 snd_hda_codec,snd_hda_intel,snd_hda_controller
snd_timer 26614 1 snd_pcm
snd 69340 13 snd_hda_codec_realtek,snd_hwdep,snd_timer,snd_pcm,snd_hda_codec_generic,snd_hda_codec,snd_hda_intel
$ systool -vm relevant_snd_module
EDIT
$ systool -vm snd_hda_intel
Module = "snd_hda_intel"
Attributes:
coresize = "26327"
initsize = "0"
initstate = "live"
refcnt = "5"
taint = ""
uevent = <store method only>
Parameters:
align_buffer_size = "-1"
bdl_pos_adj = "1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1"
beep_mode = "Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y"
enable_msi = "1"
enable = "Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y"
id = "(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null)"
index = "-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1"
jackpoll_ms = "0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0"
model = "(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null)"
patch = "(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null)"
position_fix = "-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1"
power_save = "1"
power_save_controller= "Y"
probe_mask = "-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1"
probe_only = "0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0"
single_cmd = "N"
snoop = "Y"
Sections:
.bss = "0xffffffffa0365a80"
.data = "0xffffffffa0365000"
.data.unlikely = "0xffffffffa03657d0"
.exit.text = "0xffffffffa0362930"
.gnu.linkonce.this_module= "0xffffffffa0365800"
.init.text = "0xffffffffa0368000"
.note.gnu.build-id = "0xffffffffa0363000"
.rodata = "0xffffffffa0363040"
.rodata.str1.1 = "0xffffffffa0363f02"
.rodata.str1.8 = "0xffffffffa03642e0"
.smp_locks = "0xffffffffa0364618"
.strtab = "0xffffffffa036b508"
.symtab = "0xffffffffa0369000"
.text = "0xffffffffa0360000"
__mcount_loc = "0xffffffffa0364848"
__param = "0xffffffffa0364628"
__verbose = "0xffffffffa0365640"
I guess it might be a rather basic configuration step that I missed and am blind to see. If so, sorry for wasting your time :-/ Hint appreciated.
Last edited by kozaki (2014-09-01 19:43:16)Read how to post correctly to get English output.
kozaki wrote:$ systool -vm relevant_snd_module;
Really? What do you think relevant_snd_module is? When you copy something from another thread, maybe it would be wise to read through it first. I tried to explain that there is no relevant_snd_module, it is a hint to the user, yes you, to use the module that is relevant in users case, which often is snd_hda_intel, which again is also mentioned in the other thread. Read it and correct your post accordingly please.
As for the issue at hand, is module-suspend-on-idle loaded? If so, disable and unload it. Start PA with '-vvvv' switch and post the log here. You might want to try defaulting the configuration for PA, meaning delete your ~/.config/pulse. Does your GPU have a hdmi sound card?
Check if you can get sound output with PA killed through speaker-test:
speaker-test -c 8 -t wav -D plug:"dmix:{CARD PCH DEV 0}"
speaker-test -c 2 -t wav -D plug:"dmix:{CARD PCH DEV 0}"
Both should work launched in that order at the same time. -
[SOLVED]No sound with ALSA. I'm looking for help with troubleshooting.
Hi!
Recently I bought a new laptop (HP Probook 450 G1). For some reason I can't hear sound from the laptop's speaker or headphones. I already read the troubleshooting guide on wiki. Unfortunately none of the solutions described on the wiki helped. I'm not using PulseAudio and I'm out of ideas.
Additional information:
Alsamixer screenshot.
~ lsmod |grep snd
snd_hda_codec_realtek 54803 1
snd_hda_codec_generic 56366 1 snd_hda_codec_realtek
snd_hda_codec_hdmi 40396 1
snd_hda_intel 22831 6
snd_hda_controller 22975 1 snd_hda_intel
snd_hda_codec 104665 5 snd_hda_codec_realtek,snd_hda_codec_hdmi,snd_hda_codec_generic,snd_hda_intel,snd_hda_controller
snd_hwdep 6652 1 snd_hda_codec
snd_pcm 83207 6 snd_hda_codec_hdmi,snd_hda_codec,snd_hda_intel,snd_hda_controller
snd_timer 19294 3 snd_pcm
snd 61276 16 snd_hda_codec_realtek,snd_hwdep,snd_timer,snd_hda_codec_hdmi,snd_pcm,snd_hda_codec_generic,snd_hda_codec,snd_hda_intel
soundcore 5551 2 snd,snd_hda_codec
~ aplay -l
**** List of PLAYBACK Hardware Devices ****
card 0: SB [HDA ATI SB], device 0: ALC888 Analog [ALC888 Analog]
Subdevices: 0/1
Subdevice #0: subdevice #0
card 0: SB [HDA ATI SB], device 1: ALC888 Digital [ALC888 Digital]
Subdevices: 1/1
Subdevice #0: subdevice #0
card 1: HDMI [HDA ATI HDMI], device 3: HDMI 0 [HDMI 0]
Subdevices: 1/1
Subdevice #0: subdevice #0
~ speaker-test
speaker-test 1.0.28
Playback device is default
Stream parameters are 48000Hz, S16_LE, 1 channels
Using 16 octaves of pink noise
Rate set to 48000Hz (requested 48000Hz)
Buffer size range from 2048 to 16384
Period size range from 1024 to 1024
Using max buffer size 16384
Periods = 4
was set period_size = 1024
was set buffer_size = 16384
0 - Front Left
Time per period = 2.651060
0 - Front Left
lspci |grep Audio
00:14.2 Audio device: Advanced Micro Devices, Inc. [AMD/ATI] SBx00 Azalia (Intel HDA)
01:00.1 Audio device: Advanced Micro Devices, Inc. [AMD/ATI] Juniper HDMI Audio [Radeon HD 5700 Series]
~ cat /proc/asound/cards
cat /proc/asound/cards
0 [SB ]: HDA-Intel - HDA ATI SB
HDA ATI SB at 0xfe024000 irq 16
1 [HDMI ]: HDA-Intel - HDA ATI HDMI
HDA ATI HDMI at 0xfdffc000 irq 43
Last edited by Skitter (2014-09-01 06:22:30)brebs wrote:
emeres wrote:Why disable a card?
So that the right output becomes the all-important *default* output. And it's conveniently a simple one-liner.
I am very aware of that, why not use index instead? It is as convenient as enable. Why leave the user with a disabled device, when it can continue to work? I consider this highly inefficient, because it does not solve the actual issue and creates a potential problem in the future.
In this case, user interaction was the cause, so it does not matter.
Edit: Typo.
Last edited by emeres (2014-08-29 17:45:29) -
[Solved] Volume Notification with Xmonad
Hello everyone,
I'm trying to get this working for my environment.
http://dmwit.com/volume/
Now, i don't have xmonad-extras package installed so obviously the exact tutorial doesn't work for me. (I would like to avoid using cabal, i've had bad experiences with it, probably cuz i did a root install) Now I've tried the tutorial but when i change the volume i only get a large dzen square with this output "()". This is what i did for that to work on my xmonad.hs file:
, ((0, 0x1008FF12), spawn "amixer -q set Master toggle")
, ((0, 0x1008FF11), spawn "amixer -q set Master 10%-")
, ((0, 0x1008FF13), spawn "amixer -q set Master 10%+; ~/.xmonad/bin/volume.sh" >>= alert)
alert = dzenConfig centered . show
centered =
onCurr (center 150 66)
>=> font "-*-helvetica-*-r-*-*-64-*-*-*-*-*-*-*"
>=> addArgs ["-fg", "#80c0ff"]
>=> addArgs ["-bg", "#000040"]
The script volume.sh outputs the current value of the master. I currently use that script to output the volume to my xmobar. Of course output to screen and xmobar is redundant but i just like the visual .
Is there a way to output the value of the script into a function in xmonad? In this case the alert function.
After some googling i came accross this http://reddit.com.marqueefy.com/r/xmona … _spawpipe/
but unfortunately i can seem to have the readprocess to work. (really cant figure out the syntax for it)
Any input would be greatly appreciated.
Thank you
Dave
Last edited by davama (2015-03-23 12:03:52)This is solved.
The only solution i found was to install all my haskell programs using cabal exclusively as so:
pacman -S ghc cabal-install happy alex
cabal update
cabal install cabal-install
cabal install xmonad xmonad-contrib <<< here you should be using cabal from your local directory. ~/.cabal/bin/cabal
cabal install xmonad-extras
cabal install xmobar --flags="with_mpd"
got into trouble when mixing packages from the official repo with haskell ones. Since they all come from haskell there should be no issues with conflicts. Granted some libraries get updated which cause xmonad to break but a simple delete and reinstall will do the trick. (has happened only once so far):
remove ~/.ghc
#### rerun cabal update, cabal install.... etc
Hope it makes sense and it's useful to someone. -
No biggie but... when I upgraded to 10.4.9, all went well I except I lost my screensaver sound on all screensavers with sound. Reinstalling screensavers did not work. All other sound works fine. Any ideas on how to fix? Thanks for in advance for anyone's time!
try upgrading to 10.4.10 with software update (>Software Update...)
-
Hi! I'm using alsa on a laptop with master, speaker and PCM at 100%, and I still can't get an output as loud as I'd like.
On ubuntu with pulseaudio, I had the option of setting the volume to 120% on the sound preferences menu, which made a desirable volume level for me. Is there an equivalent thing in arch? Is this like setting PCM to something higher than 0b?
Cheers!
Last edited by orlox (2010-08-14 20:09:46)Just installed pulseaudio. Not really a solution to the name of this thread, since I didn't get a loud volume with ALSA, but it solves my problem of having low volume on my PC
-
[Solved] No sound with udev 173
After updating to udev 173, i don't have any sound. The problem resolves when downgrading to udev 172. I compared the permissions in /dev/snd:
< drwxr-xr-x 2 root root 60 by-path
< crw-rw----+ 1 root audio 116, 8 controlC0
< crw-rw----+ 1 root audio 116, 7 hwC0D2
< crw-rw----+ 1 root audio 116, 6 pcmC0D0c
< crw-rw----+ 1 root audio 116, 5 pcmC0D0p
< crw-rw----+ 1 root audio 116, 4 pcmC0D1c
< crw-rw----+ 1 root audio 116, 3 pcmC0D1p
< crw-rw----+ 1 root audio 116, 2 pcmC0D2c
< crw-rw---- 1 root audio 116, 1 seq
< crw-rw----+ 1 root audio 116, 33 timer
> drwxr-xr-x 2 root root 60 by-path
> crw-rw---- 1 root audio 116, 8 controlC0
> crw-rw---- 1 root audio 116, 7 hwC0D2
> crw-rw---- 1 root audio 116, 6 pcmC0D0c
> crw-rw---- 1 root audio 116, 5 pcmC0D0p
> crw-rw---- 1 root audio 116, 4 pcmC0D1c
> crw-rw---- 1 root audio 116, 3 pcmC0D1p
> crw-rw---- 1 root audio 116, 2 pcmC0D2c
> crw-rw---- 1 root audio 116, 1 seq
> crw-rw---- 1 root audio 116, 33 timer
I don't know if it's related, but i noticed a segfault in dmesg:
[ 209.583561] gnome-settings-[725]: segfault at b3aca160 ip b3aca160 sp bfcaeccc error 4
What should i do?
Edit: Fixed with 173-2.
Last edited by Wey (2011-07-31 15:25:53)Please mark your topic solved Wey.
-
[solved] No sound with ALC269VB on asus 1215b EeePC
Hello,
I've just finished the basic install on a Asus Eee PC 1215B (with an APU C-50) and I'm having problems to make the sound work. I've googled around without succes...
# aplay -l
**** List of PLAYBACK Hardware Devices ****
card 0: Generic [HD-Audio Generic], device 3: HDMI 0 [HDMI 0]
Subdevices: 1/1
Subdevice #0: subdevice #0
card 1: SB [HDA ATI SB], device 0: ALC269VB Analog [ALC269VB Analog]
Subdevices: 1/1
Subdevice #0: subdevice #0
# cat /proc/asound/card1/pcm0p/info
card: 1
device: 0
subdevice: 0
stream: PLAYBACK
id: ALC269VB Analog
name: ALC269VB Analog
subname: subdevice #0
class: 0
subclass: 0
subdevices_count: 1
subdevices_avail: 1
# cat /etc/modprobe.d/modprobe.conf
blacklist radeon
option snd-hda-intel mode=auto
I've runned alsaconf and rebooted several times and nothing helped...
When I run alsamixer, the default chip that appears is ATI R6xx HDMI, with only S/PDIF channel, when I change card to HDA ATI SB (chip Realtek ALC269VB) it appears the usual channels the change volume. Only mic is muted, the I run speaker-test:
# speaker-test -c 1
speaker-test 1.0.24.2
Playback device is default
Stream parameters are 48000Hz, S16_LE, 1 channels
Using 16 octaves of pink noise
ALSA lib pcm_dmix.c:1018:(snd_pcm_dmix_open) unable to open slave
Playback open error: -2,No such file or directory
I dont have ideas to solve this...
Could someone help me??
Gratefull,
Heitor.
Last edited by heitorpb (2012-01-22 20:00:19)New try. Check IDs with:
cat /proc/asound/card0/id
cat /proc/asound/card1/id
Then do something like
options snd-hda-intel id=SB,HDMI index=0,1
using the IDs you got with the commands above.
As for .asoundrc, I've seen one recently, but can't remember where. Edit - Found it:
pcm.!default {
type hw
card SB
ctl.!default {
type hw
card SB
However this will only play one sound at a time. Check here if you want to play around with this stuff: http://alsa.opensrc.org/FAQ026. Hopefully you won't need to.
Last edited by Gusar (2012-01-22 20:02:39) -
[SOLVED] No sound with Chromium, libpepflashplayer problem.
Hi,
I had problem with no sound in Chromium when using the flashplayer, but it all worked in Firefox.
The problem was the chromium-pepper-flash player that I used as described in the Wiki.
with that player I get following message when starting Chromium:
ALSA lib setup.c:565:(add_elem) Cannot obtain info for CTL elem (MIXER,'Audigy Analog/Digital Output Jack',0,0,0): No such file or directory
But if I use:
Shockwave Flash
Version: 11.2 r202
Location: /usr/lib/mozilla/plugins/libflashplayer.so
Type: NPAPI
I got sound ok, unfortunately the player crach much more often, something that was the reason I changed to chromium-pepper-flash player
Any ides why I do not get sound in Chromium with chromium-pepper-flash player?
Best regards.
Christer
Last edited by agkbill (2012-12-08 08:29:34)To share my findings.
The problem was a the settings in asound.conf.
My old "asound.conf."
# conver alsa API over jack API
# use it with
# % aplay foo.wav
# use this as default
pcm.!default {
type plug
slave { pcm "jack" }
ctl.mixer0 {
type hw
card 1
# pcm type jack
pcm.jack {
type jack
playback_ports {
0 system:playback_1
1 system:playback_2
capture_ports {
0 system:capture_1
1 system:capture_2
Left since I was playing around wirh PureData and Jack.
All my outher audio apps like mpd, xbmc worked just finde with this one but not libpepflashplayer.
My new asound.conf
# use this as default
pcm.!default {
type hw
card 0
device 0
ctl.mixer0 {
type hw
card 0
With the new one also libpepflashplayer works OK.
Using libflashplayer was a very bad option for me because it crash so often. libpepflashplayer much more stable for me.
All the best.
Christer -
[SOLVED] No sound with Asus Xonar DGX
I've got no sound so I've looked into journalctl and there were some bluez and pulseaudio related erros. So i.a.w. this topic https://bbs.archlinux.org/viewtopic.php?id=155714 I did `systemctl enable bluetooth.service`. No more errors but still no sound.
Other things I did:
- unplug/plug headphones
- check whether anything is muted in alsamixer and the gnome sound applet (note: nothing is greyed-out, microphone picks up signals)
snd_oxygen i.e. ASUS XONAR is the sound card I would like to use and I hook my headphones to.
# cat /proc/asound/cards
0 [DGX ]: CMI8786 - Xonar DGX
C-Media Oxygen HD Audio at 0xee00, irq 17
1 [HDMI ]: HDA-Intel - HDA ATI HDMI
HDA ATI HDMI at 0xfd7fc000 irq 30
# lsmod | grep '^snd' | column -t
snd_hda_codec_hdmi 49263 1
snd_hda_intel 26387 2
snd_hda_controller 26857 1 snd_hda_intel
snd_oxygen 23783 2
snd_hda_codec 112621 3 snd_hda_codec_hdmi,snd_hda_intel,snd_hda_controller
snd_oxygen_lib 36709 1 snd_oxygen
snd_hwdep 17244 1 snd_hda_codec
snd_mpu401_uart 13507 1 snd_oxygen_lib
snd_rawmidi 26806 1 snd_mpu401_uart
snd_seq_device 13307 1 snd_rawmidi
snd_pcm 88779 5 snd_hda_codec_hdmi,snd_oxygen_lib,snd_hda_codec,snd_hda_intel,snd_hda_controller
snd_timer 26614 1 snd_pcm
snd 73436 19 snd_oxygen,snd_hwdep,snd_timer,snd_hda_codec_hdmi,snd_pcm,snd_rawmidi,snd_oxygen_lib,snd_hda_codec,snd_hda_intel,snd_mpu401_uart,snd_seq_device
# journalctl -b | grep -i bluez
Apr 26 12:13:52 arch1411 dbus[326]: [system] Activating via systemd: service name='org.bluez' unit='dbus-org.bluez.service'
Apr 26 12:13:52 arch1411 dbus[326]: [system] Successfully activated service 'org.bluez'
Apr 26 12:14:31 arch1411 /usr/lib/gdm/gdm-x-session[359]: Activating service name='org.bluez.obex'
Apr 26 12:14:31 arch1411 /usr/lib/gdm/gdm-x-session[359]: Successfully activated service 'org.bluez.obex'
[root@arch1411 hg1]# journalctl -b | grep -i audio
Apr 26 12:13:50 arch1411 kernel: snd_hda_intel 0000:01:00.1: Handle VGA-switcheroo audio client
Apr 26 12:13:52 arch1411 rtkit-daemon[432]: Successfully made thread 431 of process 431 (/usr/bin/pulseaudio) owned by '1000' high priority at nice level -11.
Apr 26 12:13:52 arch1411 rtkit-daemon[432]: Successfully made thread 456 of process 431 (/usr/bin/pulseaudio) owned by '1000' RT at priority 5.
Apr 26 12:13:52 arch1411 rtkit-daemon[432]: Successfully made thread 497 of process 431 (/usr/bin/pulseaudio) owned by '1000' RT at priority 5.
Apr 26 12:13:52 arch1411 rtkit-daemon[432]: Successfully made thread 498 of process 431 (/usr/bin/pulseaudio) owned by '1000' RT at priority 5.
Apr 26 15:37:00 arch1411 vlc.desktop[876]: [00007ffabc009ee8] mpgatofixed32 audio converter error: libmad error: bad main_data_begin pointer
Apr 26 15:37:02 arch1411 vlc.desktop[876]: [00007ffae0c244f8] mpgatofixed32 audio converter error: libmad error: bad main_data_begin pointer
# systemctl status pulseaudio.service
● pulseaudio.service
Loaded: not-found (Reason: No such file or directory)
Active: inactive (dead)
# systemctl start pulseaudio.service
Failed to start pulseaudio.service: Unit pulseaudio.service failed to load: No such file or directory.
Should I proceed per https://bbs.archlinux.org/viewtopic.php?id=149501 and remove pulseaudio daemon from the /etc/rc.conf file?
Last edited by bbarcher (2015-05-01 07:42:36)systemctl --all --no-pager|grep -i pulse
returns nothing.
Thank you for your input, V1del.
$ pacmd list-cards
2 card(s) available.
index: 0
name: <alsa_card.pci-0000_01_00.1>
driver: <module-alsa-card.c>
owner module: 6
properties:
alsa.card = "0"
alsa.card_name = "HDA ATI HDMI"
alsa.long_card_name = "HDA ATI HDMI at 0xfd7fc000 irq 30"
alsa.driver_name = "snd_hda_intel"
device.bus_path = "pci-0000:01:00.1"
sysfs.path = "/devices/pci0000:00/0000:00:02.0/0000:01:00.1/sound/card0"
device.bus = "pci"
device.vendor.id = "1002"
device.vendor.name = "Advanced Micro Devices, Inc. [AMD/ATI]"
device.product.id = "aa88"
device.product.name = "Barts HDMI Audio [Radeon HD 6800 Series]"
device.string = "0"
device.description = "Barts HDMI Audio [Radeon HD 6800 Series]"
module-udev-detect.discovered = "1"
device.icon_name = "audio-card-pci"
profiles:
output:hdmi-stereo: Digital Stereo (HDMI) Output (priority 5400, available: unknown)
output:hdmi-surround: Digital Surround 5.1 (HDMI) Output (priority 300, available: unknown)
output:hdmi-surround71: Digital Surround 7.1 (HDMI) Output (priority 300, available: unknown)
off: Off (priority 0, available: unknown)
active profile: <output:hdmi-stereo>
sinks:
alsa_output.pci-0000_01_00.1.hdmi-stereo/#0: Barts HDMI Audio [Radeon HD 6800 Series] Digital Stereo (HDMI)
sources:
alsa_output.pci-0000_01_00.1.hdmi-stereo.monitor/#0: Monitor of Barts HDMI Audio [Radeon HD 6800 Series] Digital Stereo (HDMI)
ports:
hdmi-output-0: HDMI / DisplayPort (priority 5900, latency offset 0 usec, available: no)
properties:
device.icon_name = "video-display"
index: 1
name: <alsa_card.pci-0000_04_04.0>
driver: <module-alsa-card.c>
owner module: 24
properties:
alsa.card = "1"
alsa.card_name = "Xonar DGX"
alsa.long_card_name = "C-Media Oxygen HD Audio at 0xee00, irq 17"
alsa.driver_name = "snd_oxygen"
device.bus_path = "pci-0000:04:04.0"
sysfs.path = "/devices/pci0000:00/0000:00:05.0/0000:03:00.0/0000:04:04.0/sound/card1"
device.bus = "pci"
device.vendor.id = "13f6"
device.vendor.name = "C-Media Electronics Inc"
device.product.id = "8788"
device.product.name = "CMI8788 [Oxygen HD Audio]"
device.string = "1"
device.description = "CMI8788 [Oxygen HD Audio]"
module-udev-detect.discovered = "1"
device.icon_name = "audio-card-pci"
profiles:
input:analog-stereo: Analog Stereo Input (priority 60, available: unknown)
output:analog-stereo: Analog Stereo Output (priority 6000, available: unknown)
output:analog-stereo+input:analog-stereo: Analog Stereo Duplex (priority 6060, available: unknown)
off: Off (priority 0, available: unknown)
active profile: <output:analog-stereo+input:analog-stereo>
sinks:
alsa_output.pci-0000_04_04.0.analog-stereo/#1: CMI8788 [Oxygen HD Audio] Analog Stereo
sources:
alsa_output.pci-0000_04_04.0.analog-stereo.monitor/#1: Monitor of CMI8788 [Oxygen HD Audio] Analog Stereo
alsa_input.pci-0000_04_04.0.analog-stereo/#2: CMI8788 [Oxygen HD Audio] Analog Stereo
ports:
analog-input-front-mic: Front Microphone (priority 8500, latency offset 0 usec, available: unknown)
properties:
device.icon_name = "audio-input-microphone"
analog-input-mic: Microphone (priority 8700, latency offset 0 usec, available: unknown)
properties:
device.icon_name = "audio-input-microphone"
analog-input-linein: Line In (priority 8100, latency offset 0 usec, available: unknown)
properties:
analog-input-aux: Analog Input (priority 8000, latency offset 0 usec, available: unknown)
properties:
analog-output-headphones: Headphones (priority 9000, latency offset 0 usec, available: unknown)
properties:
device.icon_name = "audio-headphones"
$ pacmd list-sinks
2 sink(s) available.
index: 0
name: <alsa_output.pci-0000_01_00.1.hdmi-stereo>
driver: <module-alsa-card.c>
flags: HARDWARE DECIBEL_VOLUME LATENCY FLAT_VOLUME DYNAMIC_LATENCY
state: SUSPENDED
suspend cause: IDLE
priority: 9050
volume: front-left: 65536 / 100% / 0.00 dB, front-right: 65536 / 100% / 0.00 dB
balance 0.00
base volume: 65536 / 100% / 0.00 dB
volume steps: 65537
muted: no
current latency: 0.00 ms
max request: 0 KiB
max rewind: 0 KiB
monitor source: 0
sample spec: s16le 2ch 44100Hz
channel map: front-left,front-right
Stereo
used by: 0
linked by: 0
configured latency: 0.00 ms; range is 0.50 .. 1999.82 ms
card: 0 <alsa_card.pci-0000_01_00.1>
module: 6
properties:
alsa.resolution_bits = "16"
device.api = "alsa"
device.class = "sound"
alsa.class = "generic"
alsa.subclass = "generic-mix"
alsa.name = "HDMI 0"
alsa.id = "HDMI 0"
alsa.subdevice = "0"
alsa.subdevice_name = "subdevice #0"
alsa.device = "3"
alsa.card = "0"
alsa.card_name = "HDA ATI HDMI"
alsa.long_card_name = "HDA ATI HDMI at 0xfd7fc000 irq 30"
alsa.driver_name = "snd_hda_intel"
device.bus_path = "pci-0000:01:00.1"
sysfs.path = "/devices/pci0000:00/0000:00:02.0/0000:01:00.1/sound/card0"
device.bus = "pci"
device.vendor.id = "1002"
device.vendor.name = "Advanced Micro Devices, Inc. [AMD/ATI]"
device.product.id = "aa88"
device.product.name = "Barts HDMI Audio [Radeon HD 6800 Series]"
device.string = "hdmi:0"
device.buffering.buffer_size = "352768"
device.buffering.fragment_size = "176384"
device.access_mode = "mmap+timer"
device.profile.name = "hdmi-stereo"
device.profile.description = "Digital Stereo (HDMI)"
device.description = "Barts HDMI Audio [Radeon HD 6800 Series] Digital Stereo (HDMI)"
alsa.mixer_name = "ATI R6xx HDMI"
alsa.components = "HDA:1002aa01,00aa0100,00100200"
module-udev-detect.discovered = "1"
device.icon_name = "audio-card-pci"
ports:
hdmi-output-0: HDMI / DisplayPort (priority 5900, latency offset 0 usec, available: no)
properties:
device.icon_name = "video-display"
active port: <hdmi-output-0>
* index: 1
name: <alsa_output.pci-0000_04_04.0.analog-stereo>
driver: <module-alsa-card.c>
flags: HARDWARE HW_MUTE_CTRL HW_VOLUME_CTRL DECIBEL_VOLUME LATENCY FLAT_VOLUME DYNAMIC_LATENCY
state: SUSPENDED
suspend cause: IDLE
priority: 9059
volume: front-left: 65536 / 100% / 0.00 dB, front-right: 65536 / 100% / 0.00 dB
balance 0.00
base volume: 65536 / 100% / 0.00 dB
volume steps: 65537
muted: no
current latency: 0.00 ms
max request: 0 KiB
max rewind: 0 KiB
monitor source: 1
sample spec: s16le 2ch 48000Hz
channel map: front-left,front-right
Stereo
used by: 0
linked by: 0
configured latency: 0.00 ms; range is 0.50 .. 1837.50 ms
card: 1 <alsa_card.pci-0000_04_04.0>
module: 24
properties:
alsa.resolution_bits = "16"
device.api = "alsa"
device.class = "sound"
alsa.class = "generic"
alsa.subclass = "generic-mix"
alsa.name = "Multichannel"
alsa.id = "Multichannel"
alsa.subdevice = "0"
alsa.subdevice_name = "subdevice #0"
alsa.device = "0"
alsa.card = "1"
alsa.card_name = "Xonar DGX"
alsa.long_card_name = "C-Media Oxygen HD Audio at 0xee00, irq 17"
alsa.driver_name = "snd_oxygen"
device.bus_path = "pci-0000:04:04.0"
sysfs.path = "/devices/pci0000:00/0000:00:05.0/0000:03:00.0/0000:04:04.0/sound/card1"
device.bus = "pci"
device.vendor.id = "13f6"
device.vendor.name = "C-Media Electronics Inc"
device.product.id = "8788"
device.product.name = "CMI8788 [Oxygen HD Audio]"
device.string = "hw:1"
device.buffering.buffer_size = "352800"
device.buffering.fragment_size = "352800"
device.access_mode = "mmap+timer"
device.profile.name = "analog-stereo"
device.profile.description = "Analog Stereo"
device.description = "CMI8788 [Oxygen HD Audio] Analog Stereo"
alsa.mixer_name = "CMI8786"
alsa.components = "CS4245 CMI8786"
module-udev-detect.discovered = "1"
device.icon_name = "audio-card-pci"
ports:
analog-output-headphones: Headphones (priority 9000, latency offset 0 usec, available: unknown)
properties:
device.icon_name = "audio-headphones"
active port: <analog-output-headphones>
After all of the recommended solutions from the wiki I still get
$ systemctl status pulseaudio.service
● pulseaudio.service
Loaded: not-found (Reason: No such file or directory)
Active: inactive (dead)
$ pulseaudio -vvvv
I: [pulseaudio] main.c: setrlimit(RLIMIT_NICE, (31, 31)) failed: Operation not permitted
I: [pulseaudio] main.c: setrlimit(RLIMIT_RTPRIO, (9, 9)) failed: Operation not permitted
D: [pulseaudio] core-rtclock.c: Timer slack is set to 50 us.
D: [pulseaudio] core-util.c: RealtimeKit worked.
I: [pulseaudio] core-util.c: Successfully gained nice level -11.
I: [pulseaudio] main.c: This is PulseAudio 6.0
D: [pulseaudio] main.c: Compilation host: x86_64-unknown-linux-gnu
D: [pulseaudio] main.c: Compilation CFLAGS: -march=x86-64 -mtune=generic -O2 -pipe -fstack-protector-strong --param=ssp-buffer-size=4 -Wall -W -Wextra -Wno-long-long -Wno-overlength-strings -Wunsafe-loop-optimizations -Wundef -Wformat=2 -Wlogical-op -Wsign-compare -Wformat-security -Wmissing-include-dirs -Wformat-nonliteral -Wpointer-arith -Winit-self -Wdeclaration-after-statement -Wfloat-equal -Wmissing-prototypes -Wredundant-decls -Wmissing-declarations -Wmissing-noreturn -Wshadow -Wendif-labels -Wcast-align -Wstrict-aliasing -Wwrite-strings -Wno-unused-parameter -ffast-math -fno-common -fdiagnostics-show-option -fdiagnostics-color=auto
D: [pulseaudio] main.c: Running on host: Linux x86_64 3.19.3-3-ARCH #1 SMP PREEMPT Wed Apr 8 14:10:00 CEST 2015
D: [pulseaudio] main.c: Found 6 CPUs.
I: [pulseaudio] main.c: Page size is 4096 bytes
D: [pulseaudio] main.c: Compiled with Valgrind support: no
D: [pulseaudio] main.c: Running in valgrind mode: no
D: [pulseaudio] main.c: Running in VM: no
D: [pulseaudio] main.c: Optimized build: yes
D: [pulseaudio] main.c: FASTPATH defined, only fast path asserts disabled.
I: [pulseaudio] main.c: Machine ID is d36c9fa4b78f4c8cae7f7ad7897683e3.
I: [pulseaudio] main.c: Session ID is c1.
I: [pulseaudio] main.c: Using runtime directory /run/user/1000/pulse.
I: [pulseaudio] main.c: Using state directory /home/hg1/.config/pulse.
I: [pulseaudio] main.c: Using modules directory /usr/lib/pulse-6.0/modules.
I: [pulseaudio] main.c: Running in system mode: no
E: [pulseaudio] pid.c: Daemon already running.
E: [pulseaudio] main.c: pa_pid_file_create() failed.
Last edited by bbarcher (2015-04-27 19:16:41) -
[SOLVED] No Sound with ALSA & Pulseaudio
Recently I made the transition from Debian to Arch, installed on a
seperate partition using the chroot install method.
All went smoothly, with the exception that there is no audio whatsoever.
Over the last week I've read through the related topics on the wiki and searched the forum,
but to no avail
Any assistance would be appreciated.
Here are some details;
lspci | grep audio
00:1b.0 Audio device [0403]: Intel Corporation 82801FB/FBM/FR/FW/FRW
(ICH6 Family) High Definition Audio Controller [8086:2668] (rev 03)
lsmod | grep snd
snd_intel8x0m 9736 0
snd_ac97_codec 89404 1 snd_intel8x0m
ac97_bus 910 1 snd_ac97_codec
snd_hda_codec_realtek 35187 1
snd_hda_intel 31255 0
snd_hda_codec 128666 2 snd_hda_codec_realtek,snd_hda_intel
snd_hwdep 4750 1 snd_hda_codec
snd_pcm_oss 33509 0
snd_mixer_oss 12450 1 snd_pcm_oss
snd_pcm 63880 5
snd_pcm_oss,snd_ac97_codec,snd_hda_codec,snd_hda_intel,snd_intel8x0m
snd_page_alloc 5978 3 snd_pcm,snd_hda_intel,snd_intel8x0m
snd_seq_dummy 1131 0
snd_seq_oss 25116 0
snd_seq_midi 4104 0
snd_seq_midi_event 4484 2 snd_seq_oss,snd_seq_midi
snd_rawmidi 14828 1 snd_seq_midi
snd_seq 41044 6
snd_seq_midi_event,snd_seq_oss,snd_seq_dummy,snd_seq_midi
snd_seq_device 4256 5
snd_seq,snd_rawmidi,snd_seq_oss,snd_seq_dummy,snd_seq_midi
snd_timer 14946 2 snd_pcm,snd_seq
snd 44566 14
snd_hda_codec_realtek,snd_pcm_oss,snd_ac97_codec,snd_hwdep,snd_timer,snd_pcm,snd_se$
soundcore 4386 1 snd
ls /dev/snd/*
/dev/snd/controlC0
/dev/snd/hwC0D2
/dev/snd/seq
/dev/snd/timer
/dev/snd/by-path:
pci-0000:00:1b.0
cat /proc/asound/modules
0 snd_hda_intel
aplay -lL
null
Discard all samples (playback) or generate zero samples (capture)
pulse
PulseAudio Sound Server
default
Default ALSA Output (currently PulseAudio Sound Server)
**** List of PLAYBACK Hardware Devices ****
Screenshots of alsamixer
http://www.imgbin.org/index.php?page=image&id=15874
http://www.imgbin.org/index.php?page=image&id=15875
pavucontrol shows no devices for configuration
Last edited by naesk (2013-12-13 08:11:44)a couple of days i had a similar problem, because sound modules for my internal modem were loaded. maybe you can try to blacklist the snd_hda_codec_realtek module, which looks like a network card.
you can achieve that by putting
blacklist snd_hda_codec_realtek
in /etc/modprobe.d/modprobe.conf and reboot.
rgds
hcjl
Last edited by hcjl (2013-12-13 08:39:48)
Maybe you are looking for
-
BAPI_PROJECT_MAINTAIN problem while creating milestone
Hi all, We created the milestone by using the function module. BAPI_PROJECT_MAINTAIN We get a success message such as milesone 00000020 created but the same is not getting displayed either in CJ20N or MLST table. Guess there is some problem with the
-
I recently updated my Ipad2 to iOS7 and suddenly have 794 emails in my inbox which were previously reviewed and deleted. How can I get rid of them without doing one at a time?
-
Apple replaced the logic board, wiped the computer, did a fresh instal of the OS, and also a fresh instal of all the programs during the beginning of 2015. The GeekBench scores are the highest of any of the similar computers (at least on the day of m
-
Grand Total not coming correctly in Tabular report
Hi, When I extract in Answers the following information: Dimension 1 Dimension 2 Dimension 3 Metric 1 (sum)(sum i defined in RPD) Metric 2 (count distinct)(count is defined in RPD) When doing this, I get the right result for every value of the dimens
-
Hi to All, I want to migrate the Standard WBS elements,Network from one syatem to another SaP system.. Can u specify,which is the best method to migrate the data... If it is ALE,Pls give the details of process code and message type..i didnt g