[SOLVED] Missing acpi hwmon sysfs interface on Eeepc 1000H

Hi,
I am running a fresh install using Linux 3.15.8-1-ARCH kernel on Asus Eeepc 1000H and there is a problem with the detected thermal sensors.
After configuring sensors using sensors-detect (yes to all answers, full detection), I only get this:
$ sensors
coretemp-isa-0000
Adapter: ISA adapter
Core 0:        +4.0°C  (crit = +90.0°C)
eeepc-isa-0000
Adapter: ISA adapter
fan1:         970 RPM
It misses the acpitz-virtual-0 corresponding to the acpi thermal zone which temperature can be read in /sys/class/thermal/thermal_zone0/temp and with "acpi -t" command.
Unfortunately, the temperature reported by coretemp-isa-0000 sensor is wildly wrong, and cannot be used to drive fancontrol, whereas the acpi temperature is correct.
I checked that hwmon, thermal_sys, coretemp and eeepc_laptop modules are loaded.
I also tried to add /etc/sensors.d/EeePC-0123456789 as said in https://forums.archlinux.fr/topic14506.html (french):
chip "acpitz-virtual-0"
  label temp1 "temp1"
  compute temp1 @-20,@-20
  label temp2 "Core 0"
  compute temp2 @-20,@-20
but I am not able to get the desired output of sensors -u. all I get is that:
$ sensors -u
coretemp-isa-0000
Adapter: ISA adapter
Core 0:
  temp2_input: 2.000
  temp2_crit: 90.000
  temp2_crit_alarm: 0.000
eeepc-isa-0000
Adapter: ISA adapter
fan1:
  fan1_input: 980.000
I also tried to install acpi-eeepc-generic from AUR, but unsurprisingly, it did not change anything.
All I can tell about former behaviour is that I had no problem running sensors and using fancontrol with Xubuntu 12.04 which uses 3.2.0 kernel.
Can someone give me a clue of what is going on here about missing acpitz-virtual-0 sensor ?
Best regards,
archer38
Last edited by archer38 (2015-06-03 14:53:13)

The computer is now broken, so marking thread as solved even if the issue has not been really solved.

Similar Messages

  • Missing ACPI driver

    I bought an hdtv capture card: Fusion HDTV7 RT Gold, for which the drivers already exist in the kernel, and the small firmware file is available for placement in /lib/firmware. No problem -- put the card in, started xine and got a brilliant hdtv picture. The sensitivity of this card is remarkable, since I am in a difficult reception area. But trying to fine tune the antenna led to difficulties neither femon or atscap worked any longer. The following from dmesg suggests that I have an ACPI driver conflict, and that a driver is missing:
    Linux video capture interface: v2.00
    cx88/0: cx2388x v4l2 driver version 0.0.6 loaded
    cx8800 0000:00:08.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19
    cx88[0]: subsystem: 18ac:d610, board: DViCO FusionHDTV 7 Gold
    [card=65,autodetec
    ted], frontend(s): 1
    cx88[0]: TV tuner type 76, Radio tuner type -1
    cx2388x alsa driver version 0.0.6 loaded
    cx88/2: cx2388x MPEG-TS Driver Manager version 0.0.6 loaded
    tuner' 0-0061: chip found @ 0xc2 (cx88[0])
    xc5000 0-0061: creating new instance
    xc5000: Successfully identified at address 0x61
    xc5000: Firmware has not been loaded previously
    xc5000: waiting for firmware upload (dvb-fe-xc5000-1.1.fw)...
    i2c-adapter i2c-0: firmware: requesting dvb-fe-xc5000-1.1.fw
    xc5000: firmware read 12332 bytes.
    xc5000: firmware upload
    cx88[0]: Calling XC5000 callback
    cx88[0]/0: found at 0000:00:08.0, rev: 5, irq: 19, latency: 32, mmio:
    0xdc000000
    IRQ 19/cx88[0]: IRQF_DISABLED is not guaranteed on shared IRQs
    input: i2c IR (FusionHDTV) as /devices/virtual/input/input8
    ir-kbd-i2c: i2c IR (FusionHDTV) detected at i2c-0/0-006b/ir0 [cx88[0]]
    cx88[0]/0: registered device video0 [v4l2]
    cx88[0]/0: registered device vbi0
    cx88_audio 0000:00:08.1: PCI INT A -> GSI 19 (level, low) -> IRQ 19
    IRQ 19/cx88[0]: IRQF_DISABLED is not guaranteed on shared IRQs
    cx88[0]/1: CX88x/0: ALSA support for cx2388x boards
    cx88[0]/2: cx2388x 8802 Driver Manager
    cx88-mpeg driver manager 0000:00:08.2: PCI INT A -> GSI 19 (level, low)
    -> IRQ 1
    9
    cx88[0]/2: found at 0000:00:08.2, rev: 5, irq: 19, latency: 32, mmio:
    0xde000000
    IRQ 19/cx88[0]: IRQF_DISABLED is not guaranteed on shared IRQs
    ACPI: I/O resource vt596_smbus [0x400-0x407] conflicts with ACPI region
    SMOV [0x
    400-0x406]
    ACPI: Device needs an ACPI driver
    cx88/2: cx2388x dvb driver version 0.0.6 loaded
    cx88/2: registering cx8802 driver, type: dvb access: shared
    cx88[0]/2: subsystem: 18ac:d610, board: DViCO FusionHDTV 7 Gold
    [card=65]
    cx88[0]/2: cx2388x based DVB/ATSC card
    cx8802_alloc_frontends() allocating 1 frontend(s)
    xc5000 0-0061: attaching existing instance
    xc5000: Successfully identified at address 0x61
    xc5000: Firmware has been loaded previously
    DVB: registering new adapter (cx88[0])
    DVB: registering adapter 0 frontend 0 (Samsung S5H1411 QAM/8VSB
    Frontend)...
    Any suggestions on how to fix the problem would be a great help.

    Double post: http://bbs.archlinux.org/viewtopic.php?id=72610

  • [svn:cairngorm3:] 16142: Insync Refactorings, Module lib: Added missing parameters from IModuleInfo interface.

    Revision: 16142
    Revision: 16142
    Author:   [email protected]
    Date:     2010-05-16 14:21:40 -0700 (Sun, 16 May 2010)
    Log Message:
    Insync Refactorings, Module lib: Added missing parameters from IModuleInfo interface. Maven: Take Persistence out.
    Modified Paths:
        cairngorm3/trunk/libraries/Module/src/com/adobe/cairngorm/module/ModuleInfo.as
        cairngorm3/trunk/libraries/ModuleTest/.actionScriptProperties
        cairngorm3/trunk/libraries/lib-parent/pom.xml
        cairngorm3/trunk/samples/insync/insync-basic/src/InsyncContext.mxml
        cairngorm3/trunk/samples/insync/insync-basic/src/insync/application/RefreshSearchAfterSav eController.as
        cairngorm3/trunk/samples/insync/insync-basic/src/insync/presentation/ContactList.mxml
        cairngorm3/trunk/samples/insync/insync-basic/src/insync/presentation/ContactsNavigator.mx ml
        cairngorm3/trunk/samples/insync/insync-basic/src/insync/presentation/PictureInput.mxml
        cairngorm3/trunk/samples/insync/insync-basic/src/insync/presentation/Toolbar.mxml
        cairngorm3/trunk/samples/insync/insync-basic/src/insync/presentation/ToolbarPM.as
        cairngorm3/trunk/samples/insync/insync-basic/test/insync/application/RefreshSearchAfterSa veControllerTest.as
        cairngorm3/trunk/samples/insync/insync-basic/test/insync/presentation/ToolbarPMTest.as
        cairngorm3/trunk/samples/insync/insync-modularExtended-contacts/.actionScriptProperties
        cairngorm3/trunk/samples/insync/insync-modularExtended-contacts/src/insync/contacts/appli cation/RefreshSearchAfterSaveController.as
        cairngorm3/trunk/samples/insync/insync-modularExtended-contacts/src/insync/contacts/prese ntation/ContactFormPM.as
        cairngorm3/trunk/samples/insync/insync-modularExtended-contacts/src/insync/contacts/prese ntation/PictureInput.mxml
        cairngorm3/trunk/samples/insync/insync-modularExtended-contacts/test/insync/contacts/appl ication/RefreshSearchAfterSaveControllerTest.as
        cairngorm3/trunk/samples/insync/insync-modularExtended-expenses/.actionScriptProperties
        cairngorm3/trunk/samples/insync/insync-modularExtended-expenses/src/ExpensesModule.mxml
        cairngorm3/trunk/samples/insync/insync-modularExtended-expenses/src/ExpensesModuleRig.mxm l
        cairngorm3/trunk/samples/insync/insync-modularExtended-expenses/src/ExpensesRigContext.mx ml
        cairngorm3/trunk/samples/insync/insync-modularExtended-messaging/.actionScriptProperties
        cairngorm3/trunk/samples/insync/insync-modularExtended-messaging/src/ComposeMessageModule .mxml
        cairngorm3/trunk/samples/insync/insync-modularExtended-messaging/src/ComposeMessageModule Rig.mxml
        cairngorm3/trunk/samples/insync/insync-modularExtended-messaging/src/ComposeMessageModule RigContext.mxml
        cairngorm3/trunk/samples/insync/insync-modularExtended-shell/src/insync/application/Compo seMessageController.as
        cairngorm3/trunk/samples/insync/insync-modularExtended-shell/src/insync/presentation/Cont entViewStack.mxml
        cairngorm3/trunk/samples/insync/insync-modularExtended-shell/src/insync/presentation/Tool bar.mxml
        cairngorm3/trunk/samples/insync/insync-modularExtended-shell/src/insync/presentation/Tool barPM.as
        cairngorm3/trunk/samples/insync/insync-modularExtended-shell/test/insync/presentation/Too lbarPMTest.as

  • Eeepc 1000H and elantech/synaptics result in no tapping

    Hi,
    since an update some days ago my touchpad isn't working anymore the way I want it. I use an uptodate archlinux and a custom compiled 2.6.31.5 kernel. I have no xorg.conf and this is my 11-x11-synaptics.fdi :
    <?xml version="1.0" encoding="ISO-8859-1"?>
    <deviceinfo version="0.2">
    <device>
    <match key="info.product" contains="ETPS/2 Elantech Touchpad">
    <append key="info.capabilities" type="strlist">input.touchpad</append>
    </match>
    <match key="info.capabilities" contains="input.touchpad">
    <merge key="input.x11_driver" type="string">synaptics</merge>
    <merge key="input.x11_options.TapButton1" type="string">1</merge>
    <merge key="input.x11_options.TapButton2" type="string">2</merge>
    <merge key="input.x11_options.TapButton3" type="string">3</merge>
    <!-- Arbitrary options can be passed to the driver using
    the input.x11_options property since xorg-server-1.5. -->
    <!-- EXAMPLES:
    Switch on shared memory, enables the driver to be configured at runtime
    <merge key="input.x11_options.SHMConfig" type="string">true</merge>
    Maximum movement of the finger for detecting a tap
    <merge key="input.x11_options.MaxTapMove" type="string">2000</merge>
    Enable vertical scrolling when dragging along the right edge
    <merge key="input.x11_options.VertEdgeScroll" type="string">true</merge>
    Enable vertical scrolling when dragging with two fingers anywhere on the touchpad
    <merge key="input.x11_options.VertTwoFingerScroll" type="string">true</merge>
    Enable horizontal scrolling when dragging with two fingers anywhere on the touchpad
    <merge key="input.x11_options.HorizTwoFingerScroll" type="string">true</merge>
    If on, circular scrolling is used
    <merge key="input.x11_options.CircularScrolling" type="string">true</merge>
    For other possible options, check CONFIGURATION DETAILS in synaptics man page
    -->
    </match>
    </device>
    </deviceinfo>
    And this my 9-x11-elantech.fdi:
    <?xml version="1.0" encoding="ISO-8859-1"?>
    <deviceinfo version="0.2">
    <device>
    <match key="info.capabilities" contains="input.touchpad">
    <match key="info.product" contains="Elantech Touchpad">
    <merge key="input.x11_driver" type="string">synaptics</merge>
    <merge key="input.x11_options.SHMConfig" type="string">on</merge>
    <merge key="input.x11_options.MaxSpeed" type="string">1.00</merge>
    <merge key="input.x11_options.MinSpeed" type="string">0.75</merge>
    <merge key="input.x11_options.Emulate3Buttons" type="string">on</merge>
    <merge key="input.x11_options.VertTwoFingerScroll" type="string">1</merge>
    <merge key="input.x11_options.HorizTwoFingerScroll" type="string">1</merge>
    <merge key="input.x11_options.TapButton1" type="string">1</merge>
    <merge key="input.x11_options.TapButton2" type="string">2</merge>
    <merge key="input.x11_options.TapButton3" type="string">3</merge>
    <merge key="input.x11_options.LockedDrags" type="string">11</merge>
    </match>
    </match>
    </device>
    </deviceinfo>
    Some lines of my Xorg.log:
    (II) LoadModule: "synaptics"
    (II) Loading /usr/lib/xorg/modules/input//synaptics_drv.so
    (II) Module synaptics: vendor="X.Org Foundation"
    compiled for 1.6.3, module version = 1.1.3
    Module class: X.Org XInput Driver
    ABI class: X.Org XInput driver, version 4.0
    (II) Synaptics touchpad driver version 1.1.3
    (**) Option "Device" "/dev/input/event6"
    (II) ETPS/2 Elantech Touchpad: x-axis range 8 - 1144
    (II) ETPS/2 Elantech Touchpad: y-axis range 8 - 760
    (II) ETPS/2 Elantech Touchpad: device does not report pressure, will use touch data.
    (II) ETPS/2 Elantech Touchpad: finger width range 0 - 0
    (II) ETPS/2 Elantech Touchpad: buttons: left right middle double triple
    (**) Option "SHMConfig" "on"
    (**) Option "VertTwoFingerScroll" "1"
    (**) Option "HorizTwoFingerScroll" "1"
    (WW) Option "LockedDrags" requires a boolean value
    (**) Option "TapButton1" "1"
    (**) Option "TapButton2" "2"
    (**) Option "TapButton3" "3"
    (**) Option "MinSpeed" "0.75"
    (**) Option "MaxSpeed" "1.00"
    (--) ETPS/2 Elantech Touchpad: touchpad found
    (**) ETPS/2 Elantech Touchpad: always reports core events
    (II) XINPUT: Adding extended input device "ETPS/2 Elantech Touchpad" (type: TOUCHPAD)
    (**) ETPS/2 Elantech Touchpad: (accel) keeping acceleration scheme 1
    (**) ETPS/2 Elantech Touchpad: (accel) filter chain progression: 2.00
    (**) ETPS/2 Elantech Touchpad: (accel) filter stage 0: 20.00 ms
    (**) ETPS/2 Elantech Touchpad: (accel) set acceleration profile 0
    (--) ETPS/2 Elantech Touchpad: touchpad found
    (II) config/hal: Adding input device AT Translated Set 2 keyboard
    (II) LoadModule: "evdev"
    The behavior now is: scrolling works the way I want it but tapping doesn't work at all. I have to start the gsynaptics gui to make tapping work but gsynaptics-settings aren't remembered when I reboot. Also executing gsynaptics-init with gnome doesn't solve that problem.
    How can I make tapping work again by default, so I don't have to execute gsynaptics after each boot and activate it?
    greetings

    I have an eeepc 1000h with standard install, I did the upgrade to kernel 2.6.31.
    now my touchpad has no tapping, neither three fingers scrolling. the weird thing is that the right side of the touchpad is working like a scrolling wheel...
    Also the tapping is working when I select my session or user in GDM, and afterwards it's gone, kaput, finito...
    sorry im not bringing any solution, but as we are in more or less the same situation...
    Last edited by henaken (2009-10-29 18:53:23)

  • [SOLVED] proc/acpi/button/power missing

    I have been unable to trigger an event when the power button is pressed on my laptop.
    # uname -a
    Linux julia 3.0-ARCH #1 SMP PREEMPT Tue Aug 30 08:53:25 CEST 2011 x86_64 AMD Turion(tm) 64 X2 Mobile Technology TL-50 AuthenticAMD GNU/Linux
    acpid version 2.0.10-2, started through rc.conf as daemon.
    dbus is active, HAL is not installed.
    # tail -f /var/log/messages.log
    Sep 6 14:48:03 localhost -- MARK --
    Sep 6 15:08:03 localhost -- MARK --
    Sep 6 15:28:03 localhost -- MARK --
    Sep 6 15:36:02 localhost acpid: client 1328[0:100] has disconnected
    Sep 6 15:36:02 localhost acpid: client connected from 2084[0:100]
    Sep 6 15:36:02 localhost acpid: 1 client rule loaded
    Sep 6 15:48:03 localhost -- MARK --
    Sep 6 16:08:03 localhost -- MARK --
    Sep 6 16:28:03 localhost -- MARK --
    Sep 6 16:48:03 localhost -- MARK --
    Sep 6 16:59:43 localhost logger: PowerButton pressed: PWRF
    # acpi_listen
    button/power PWRF 00000080 00000002
    That output indicates the power button is recognized by the kernel, but it have no idea what i should put in /etc/acpi/handler.sh to shutdown the laptop when the powerbutton is pressed.
    Last edited by Lone_Wolf (2011-09-07 12:02:23)

    button/power PWRF 00000080 00000002
    These are the arguments passed to the handler script ($1 to $4).
    handler.sh from acpid package:
    case "$1" in
    button/power)
    #echo "PowerButton pressed!">/dev/tty5
    case "$2" in
    PBTN|PWRF) logger "PowerButton pressed: $2" ;;
    *) logger "ACPI action undefined: $2" ;;
    esac
    Replace the logger "PowerButton [...]" command (which is responsible for the message.log line you quote) with a shutdown invocation.

  • Some fields missing from the Information interface

    On iTunes 12 I can’t find the "Description" field that was in the Video page.
    The field still shows in the list of songs, but it doesn’t appear on the new "Information" interface. And I don't think this is the only field missing compared to the previous Information interface. Can anyone help? Thank you.

    ... before you click Get Info.
    tt2
    YES!
    Thank you turing! That really helped.
    (it seems a bit of a complication to me, the system was just fine as it was, but what do I know?)

  • Access Restriction tab is missing on e3000 web interface

    I am quite sure that this tab has been there before but now its missing - could it be because I have activated  Parent Control on Cisco Connect ?
    If so - how do I 'get It back'
    (I thing parent control in Cisco connect is too limited)
    Regards
    Fleohans
    Solved!
    Go to Solution.

    Yes, the Access Restrictions tab goes away when the Parental Controls section is activated. According to the faqs, a hard reset is the only way to restore it.

  • [SOLVED]Missing /usr/lib/libgssapi.so when using conserver client

    With newly MIT krb5 in [Core] repo, everything I using console ( the client of conserver: http://aur.archlinux.org/packages.php?ID=27856), I got a compain about missing /usr/lib/libgssapi.so error.
    I recompiled it, but not work.
    Manaully create a link from /usr/lib/libgssapi_krb5.so will solve this problem.
    But still confusing about why recompile the software don't goes to correct lib file.
    Anyone can give me a clue?
    Last edited by cathay4t (2011-05-12 11:23:49)

    Where did you get that 0.1-4?
    I get this error when starting cups
    # /etc/rc.d/cups start
    :: Starting CUPS Daemon [BUSY]
    /usr/sbin/cupsd: error while loading shared libraries: libgssapi.so.2: cannot open shared object file: No such file or directory
    [FAIL]
    Last edited by markuman (2011-05-12 16:41:17)

  • After Deploying an Image: Windows Boot Manager - Missing ACPI.sys

    Hi,
    I am currently working on deploying a Windows 7 Pro x64 image to a number of clients over our network using FOG. We used KVM in Ubuntu to build the base image. The image has a small virtual disk for the Windows installation and is deployed to clients with larger
    drives. Prior to capture the image, we ran sysprep /generalize /shutdown /oobe /unattend:unattend.xml, then boot the VM to the FOG client and let FOG save off the disk image. We then deploy the image to clients over FOG.
    FOG successfully copies the image over, then reboots the PC. The computer attempts to boot from the local hard drive, then fails at the Windows Boot Manager screen, saying:
    Windows boot manager
    Windows failed to start. A recent hardware or software change might be the cause....
    File: \Windows\system32\drivers\ACPI.sys
    Status: 0xc0000098
    Info: Windows failed to load because a critical system driver is missing or corrupt.
    I've updated the client's BIOS, tried a different hard drive, used ATA secure erase to wipe the drive before formatting, and still encounter this same issue with certain client computers. Are there any other steps I can take to resolve this issue?
    What files in Panther should I look at (or post) to troubleshoot? I don't see anything too obvious in diagerr, and sestuperr.log is just about empty.

    We're using two models of 120GB SSDs, and deploying to 5 different motherboards (4 Intel models + 1 MSI model). The issue is most common with the DH55TC Intel boards.
    We're using FOG due to budget limits--otherwise, WDT definitely would have been considered.

  • [SOLVED] Missing mixer device in /dev/snd??

    I'm trying to get the gkrellm volume plugin working. When I try to configure it, the plugin can't find any mixer devices. My next step was to check the plugin source which notes that "enable_alsa=1" should be an argument to make. Since this wasn't in the PKGBUILD script, I added it and rebuilt the package. After updating and installing, I restarted gkrellm, but was still unable to locate a mixer. Since sound is working just fine, i started digging deeper.
    8< Here's the output of several diagnostic commands... >8
    $ cat /proc/asound/cards
    0 [SB             ]: HDA-Intel - HDA ATI SB
                          HDA ATI SB at 0xfe7f0000 irq 16
    1 [HDMI           ]: HDA-Intel - HDA ATI HDMI
                          HDA ATI HDMI at 0xfe8e8000 irq 19
    $ cat /proc/asound/devices
      1:        : sequencer
      2: [ 0- 1]: digital audio playback
      3: [ 0- 0]: digital audio playback
      4: [ 0- 0]: digital audio capture
      5: [ 0- 0]: hardware dependent
      6: [ 0]   : control
      7: [ 1- 3]: digital audio playback
      8: [ 1- 0]: hardware dependent
      9: [ 1]   : control
    33:        : timer
    $ l /dev/snd
    total 0
    drwxr-xr-x  2 root root       80 Jul 25 10:44 by-path/
    crw-rw----+ 1 root audio 116,  6 Jul 25 10:44 controlC0
    crw-rw----+ 1 root audio 116,  9 Jul 25 10:44 controlC1
    crw-rw----+ 1 root audio 116,  5 Jul 25 10:44 hwC0D0
    crw-rw----+ 1 root audio 116,  8 Jul 25 10:44 hwC1D0
    crw-rw----+ 1 root audio 116,  4 Jul 25 10:44 pcmC0D0c
    crw-rw----+ 1 root audio 116,  3 Jul 26 03:36 pcmC0D0p
    crw-rw----+ 1 root audio 116,  2 Jul 25 10:44 pcmC0D1p
    crw-rw----+ 1 root audio 116,  7 Jul 25 10:44 pcmC1D3p
    crw-rw----+ 1 root audio 116,  1 Jul 27 03:44 seq
    crw-rw----+ 1 root audio 116, 33 Jul 25 10:44 timer
    # lsmod |grep snd
    snd_seq                50785  0
    snd_seq_device          5372  1 snd_seq
    snd_hda_codec_hdmi     22784  1
    snd_hda_codec_realtek   297871  1
    snd_hda_intel          22186  1
    snd_hda_codec          77543  3 snd_hda_codec_hdmi,snd_hda_codec_realtek,snd_hda_intel
    snd_hwdep               6342  1 snd_hda_codec
    snd_pcm                73736  3 snd_hda_codec_hdmi,snd_hda_intel,snd_hda_codec
    snd_timer              19488  2 snd_seq,snd_pcm
    snd                    57256  11 snd_seq,snd_seq_device,snd_hda_codec_hdmi,snd_hda_codec_realtek,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm,snd_timer
    soundcore               6178  1 snd
    snd_page_alloc          7161  2 snd_hda_intel,snd_pcm
    $ pacman -Qs alsa
    local/alsa-lib 1.0.24.1-1
        An alternative implementation of Linux sound support
    local/alsa-plugins 1.0.24-2
        Extra alsa plugins
    local/alsa-utils 1.0.24.2-1
        An alternative implementation of Linux sound support
    8< end of command output >8
    I've been unable to locate a snd_mixer module for the kernel and there is no /dev/snd/mixerC?D?
    I thought that the ALSA interface had changed since I last compiled from scrath (I was a Slacker from kernel 1.2 until I migrated to Ubuntu, and now to Arch), but according to http://www.alsa-project.org/main/index. … ibrary_API, /dev/snd/mixerCXDX is still part of the interface specification.
    Did I miss an ALSA pacakage that's required to get /dev/snd/mixerCXDX?
    Or has the ALSA implementation changed (/dev/snd/mixerCXDX deperecated), in which case the gkrellm plugin needs to be updated? Google didn't turn up anything definitive and the alsa-driver-1.0.2 source tarball doesn't include a changelog.
    Thanks!
    Last edited by barthel (2011-07-29 03:07:07)

    That's what I was afraid of. I switched to Ubuntu at Dapper Drake, so I've not been up to speed with the details of program changes the way I was with Slackware. I don't want to install the OSS layer only for the sake of a volume widget.
    Thanks for the reply. I'm taking a look at Conky now as a potential replacement for gkrellm, since it hasn't been updated in years.

  • [SOLVED] "Loading Modules" Slow after Latest Upgrade (EeePC 901)

    After the latest upgrade, my EeePC is taking an incredibly long time (20+ seconds) at the "Loading Modules" stage of the boot process. I cannot find any error messages, and after the pause, the machine boots normally. This process used to be almost instantantaneous before the upgrade. The modules being loaded are rfkill and eeepc_laptop.
    Can anyone help?
    Thanks in advance
    Last edited by myrlin (2011-06-27 10:28:21)

    Hi Jason, thank you for helping me.
    Here is my rc.conf:
    # /etc/rc.conf - Main Configuration for Arch Linux
    # LOCALIZATION
    # LOCALE: available languages can be listed with the 'locale -a' command
    # DAEMON_LOCALE: If set to 'yes', use $LOCALE as the locale during daemon
    # startup and during the boot process. If set to 'no', the C locale is used.
    # HARDWARECLOCK: set to "UTC" or "localtime", any other value will result
    # in the hardware clock being left untouched (useful for virtualization)
    # Note: Using "localtime" is discouraged.
    # TIMEZONE: timezones are found in /usr/share/zoneinfo
    # KEYMAP: keymaps are found in /usr/share/kbd/keymaps
    # CONSOLEFONT: found in /usr/share/kbd/consolefonts (only needed for non-US)
    # CONSOLEMAP: found in /usr/share/kbd/consoletrans
    # USECOLOR: use ANSI color sequences in startup messages
    # VERBOSE: Verbose level (from 1 to 8). man 3 syslog for level info
    LOCALE="en_GB.UTF-8"
    DAEMON_LOCALE="no"
    HARDWARECLOCK="UTC"
    TIMEZONE="Europe/London"
    KEYMAP="uk"
    CONSOLEFONT=
    CONSOLEMAP=
    USECOLOR="yes"
    VERBOSE="3"
    # HARDWARE
    # MODULES: Modules to load at boot-up. Blacklisting is no longer supported.
    # Replace every !module by an entry as on the following line in a file in
    # /etc/modprobe.d:
    # blacklist module
    # See "man modprobe.conf" for details.
    MOD_AUTOLOAD="yes"
    MODULES=(rfkill eeepc_laptop)
    # Udev settle timeout (default to 30)
    UDEV_TIMEOUT=30
    # Scan for FakeRAID (dmraid) Volumes at startup
    USEDMRAID="no"
    # Scan for BTRFS volumes at startup
    USEBTRFS="no"
    # Scan for LVM volume groups at startup, required if you use LVM
    USELVM="no"
    # NETWORKING
    # HOSTNAME: Hostname of machine. Should also be put in /etc/hosts
    HOSTNAME="eeepc"
    # Use 'ip addr' or 'ls /sys/class/net/' to see all available interfaces.
    # Wired network setup
    # - interface: name of device (required)
    # - address: IP address (leave blank for DHCP)
    # - netmask: subnet mask (ignored for DHCP)
    # - gateway: default route (ignored for DHCP)
    # Static IP example
    # interface=eth0
    # address=192.168.0.2
    # netmask=255.255.255.0
    # gateway=192.168.0.1
    # DHCP example
    # interface=eth0
    # address=
    # netmask=
    # gateway=
    interface=eth0
    address=
    netmask=
    gateway=
    # Setting this to "yes" will skip network shutdown.
    # This is required if your root device is on NFS.
    NETWORK_PERSIST="no"
    # Enable these netcfg profiles at boot-up. These are useful if you happen to
    # need more advanced network features than the simple network service
    # supports, such as multiple network configurations (ie, laptop users)
    # - set to 'menu' to present a menu during boot-up (dialog package required)
    # - prefix an entry with a ! to disable it
    # Network profiles are found in /etc/network.d
    # This requires the netcfg package
    #NETWORKS=(main)
    # DAEMONS
    # Daemons to start at boot-up (in this order)
    # - prefix a daemon with a ! to disable it
    # - prefix a daemon with a @ to start it up in the background
    # If something other takes care of your hardware clock (ntpd, dual-boot...)
    # you should disable 'hwclock' here.
    DAEMONS=(syslog-ng dbus hal networkmanager privoxy netfs rfkill eeepc_laptop @ufw @crond @alsa !bluetooth @samba @cups)
    Here is my blacklist.conf (I have restored the framebuffer one):
    blacklist rt2800pci
    blacklist rt61pci
    blacklist rt2x00pci
    blacklist rt2800usb
    blacklist rt2800lib
    blacklist rt2x00usb
    blacklist rt2x00lib
    And here is the output of lsmod:
    Module Size Used by
    fuse 58669 3
    ipt_REJECT 2029 1
    ipt_LOG 6518 5
    xt_multiport 1498 2
    xt_limit 1423 7
    xt_tcpudp 1883 7
    xt_addrtype 2393 4
    nf_conntrack_ipv4 9601 7
    nf_defrag_ipv4 1023 1 nf_conntrack_ipv4
    xt_state 971 7
    ip6table_filter 1072 1
    ip6_tables 10461 1 ip6table_filter
    ipv6 249260 12
    nf_conntrack_netbios_ns 801 0
    nf_conntrack_broadcast 961 1 nf_conntrack_netbios_ns
    nf_conntrack_pptp 3857 0
    nf_conntrack_proto_gre 3241 1 nf_conntrack_pptp
    nf_conntrack 50208 6 nf_conntrack_ipv4,xt_state,nf_conntrack_netbios_ns,nf_conntrack_broadcast,nf_conntrack_pptp,nf_conntrack_proto_gre
    iptable_filter 1100 1
    ip_tables 9186 1 iptable_filter
    x_tables 11774 11 ipt_REJECT,ipt_LOG,xt_multiport,xt_limit,xt_tcpudp,xt_addrtype,xt_state,ip6table_filter,ip6_tables,iptable_filter,ip_tables
    btusb 9897 0
    bluetooth 115465 1 btusb
    uvcvideo 55020 0
    videodev 70734 1 uvcvideo
    media 8545 1 videodev
    joydev 7535 0
    snd_hda_codec_realtek 225687 1
    i915 557262 2
    snd_hda_intel 19261 1
    snd_hda_codec 66793 2 snd_hda_codec_realtek,snd_hda_intel
    snd_hwdep 4919 1 snd_hda_codec
    drm_kms_helper 24245 1 i915
    snd_pcm 60311 2 snd_hda_intel,snd_hda_codec
    drm 147653 3 i915,drm_kms_helper
    uhci_hcd 19344 0
    snd_timer 15542 1 snd_pcm
    ehci_hcd 34847 0
    rt2860sta 479236 1
    intel_agp 8664 1 i915
    psmouse 55927 0
    snd 43527 8 snd_hda_codec_realtek,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm,snd_timer
    usbcore 119004 5 btusb,uvcvideo,uhci_hcd,ehci_hcd
    i2c_algo_bit 4431 1 i915
    iTCO_wdt 10333 0
    i2c_i801 7039 0
    serio_raw 3430 0
    pcspkr 1415 0
    sg 21022 0
    i2c_core 16665 6 videodev,i915,drm_kms_helper,drm,i2c_algo_bit,i2c_i801
    evdev 7310 15
    intel_gtt 11417 3 i915,intel_agp
    crc_ccitt 1103 1 rt2860sta
    iTCO_vendor_support 1553 1 iTCO_wdt
    soundcore 5018 1 snd
    battery 8905 0
    processor 21884 0
    eeepc_laptop 12452 0
    atl1e 24804 0
    button 3654 1 i915
    sparse_keymap 2636 1 eeepc_laptop
    thermal 6603 0
    ac 2545 0
    video 9852 1 i915
    snd_page_alloc 5909 2 snd_hda_intel,snd_pcm
    pci_hotplug 21978 1 eeepc_laptop
    agpgart 22160 3 drm,intel_agp,intel_gtt
    rfkill 12510 2 bluetooth,eeepc_laptop
    ext4 334626 3
    mbcache 4321 1 ext4
    jbd2 59098 1 ext4
    crc16 1077 2 bluetooth,ext4
    sd_mod 25515 5
    ata_piix 18569 3
    pata_acpi 2396 0
    libata 154349 2 ata_piix,pata_acpi
    scsi_mod 110670 3 sg,sd_mod,libata
    I hope this all means more to you than it does to me!!!!

  • Missing ACPI\TOS6205 Driver

    I have a Z930 laptop. Installed clean Windows 7x64. And missing one driver.ACPI\TOS6205 as unknowndriver. After some searching this comes up as a BT ACPI driver. I was able to find a driver on line and after installing the driver is properly indentified in the device manager. However after the reboot system goes in the repair mode and then reboots and driver is still missing. None on the blue tooth drivers from the toshiba website resolve the issue.
    Some other forums say that this might be HDD driver. I tried downloading HDD drivers for the Toshiba website but none of them work. Z930 has an SSD drive. SSD driver "Intel Rapid Storage Technology Driver
    " does not help either.Thanks for the help. Running HHD protection i get an error that "HHD Protection is not supported on tbhis model"

     
    Downloads for 64-bit Windows 7
    reinstall windows 64 ultimate 
    When you reinstall Windows 7, all the applicable drivers and utilities must be installed in order for the laptop to work as designed. And the order matters. So start over with a clean install of Windows.
    You should install the Intel chipset software and the Intel display driver prior to any other drivers. That sets up the motherboard. I would install the Intel Management Engine and Storage driver next.
    If the wireless or Bluetooth doesn't work after that, I expect you have a hardware malfunction.

  • IDSM missing traffic on trunk interface

    Hi
    I have a scenario where an IDSM with IPS 6 is triggering on traffic from a non-trunk interface but when the same traffic passes over another VLAN on a trunk.
    Monitor setup is like this
    monitor session 10 source interface Gi1/2
    monitor session 10 source interface Gi7/1
    monitor session 10 filter vlan 22 - 23 , 208
    monitor session 10 destination intrusion-detection-module 5 data-port 1
    where 1/2 is the non-trunk interface and 7/1 is the trunk. Traffic from VLAN 23 is firewalled/NATed and sent out on VLAN 208 towards our edge network.
    The exact case is that when I browse an external web site with SQL code in the HTML I get an SQL Injection alert from VLAN 208 only. I never get the alert for the same traffic passing behind the firewall over the trunk. When I set a sniffer as source for the SPAN session I see the HTTP request with the SQL code passing through the trunk interface as well as VLAN 208.
    Am I missing something here? Shouldn't and IPS report ALL occurrences of bad traffic?
    Regards
    Fredrik Hofgren

    What has to be upgraded, the Catalyst IOS or the software on the IDSM? Our Catalyst has IOS 12.2(18)SXF5 and the IDSM the latest version 6.0(3)E1.
    It seems odd that it would be a problem with missing VLAN tags. When I set the IDSM to manually capture traffic from an IP in the inside VLAN passing over the trunk the VLAN tag is present when I view the packets in Ethereal.
    /Fredrik

  • [SOLVED] Recipe for target 'src/Interface/openxcom-ComboBox.o' failed

    I've been having some problems with installing openxcom, most of which appear to come from a problem with yaml-cpp 0.5.2-2, and thus, the git file in the AUR (https://aur.archlinux.org/packages/openxcom-git/) was updated with a rollback yaml-cpp.
    When I tried to build this package, there was an error involving some recipe.
    CXX src/Interface/openxcom-ComboBox.o
    src/Interface/ComboBox.cpp: In member function ‘size_t OpenXcom::ComboBox::getHoveredListIdx() const’:
    src/Interface/ComboBox.cpp:245:9: error: comparison between signed and unsigned integer expressions [-Werror=sign-compare]
    if (-1 == ret)
    ^
    cc1plus: all warnings being treated as errors
    Makefile:5043: recipe for target 'src/Interface/openxcom-ComboBox.o' failed
    make[1]: *** [src/Interface/openxcom-ComboBox.o] Error 1
    make[1]: Leaving directory '/home/sailol/Downloads/AUR/openxcom-git/src/OpenXcom'
    Makefile:7157: recipe for target 'all-recursive' failed
    make: *** [all-recursive] Error 1
    [1m[31m==> ERROR:[m[1m A failure occurred in build().[m
    [1m Aborting...[m
    After finding this post, I think it may have something to do with a header file that is missing, but I'm not sure.
    Thank you for your time.
    Last edited by Sailol (2015-06-08 01:00:46)

    Mmm, the git package (maintained by me) frequently fails due to warnings since it's a developmental package. You can override the warnings by changing enable_werror to no in configure.ac (before you run autogen.sh in the prepare function).
    sed -i 's:werror=yes:werror=no:' configure.ac
    Should do it.
    EDIT: I'd avoid the -git package for the time being, seems like a lot of stuff isn't getting installed correctly at the moment. I'll try to fix it up and upload a new PKGBUILD tomorrow.
    Last edited by WorMzy (2015-06-07 23:08:29)

  • [solved] missing latest backups for iPhone after getting replacement phone

    Thought I would share this one in case anyone else runs into it.
    My the speaker on my wife's iPhone 4 on Verizon had stopped working for phone calls for the second time and a restore didn't fix it, so she returned the phone and they gave her a new one at the store. We had made several backups over the last few days, the most recent was this morning.
    So tonight we hooked up the new phone to iTunes and got ready to restore it, but iTunes said the restore was last updated in FEBRUARY. What?! My wife freaked out thinking all her photos etc. were now lost for good.
    I held off on the restore and decided to do some checking around before doing anything. I found the folder where the restore files are, and sure enough I found files from today. I copied that folder just in case. I also checked in iTunes itself and the backups were listed. So what was up?!
    It finally occured to me that we had recently upgraded her phone to iOS 5, but that the new iPhone 4 from the store was probably still on iOS 4 -- maybe iTunes was not smart enough to see this situation and tell us about it, and maybe it won't listed iOS 5 backups for an iOS 4 phone.
    Well that turned out to be the case. But what to do to fix it? I figured if I could get iOS 5 onto the phone, we would be all set. But I didn't want to tell iTunes to label it as a new phone either -- I'm not sure if that would be permanent or what. So I took a leap of faith and held down the power button and home button simultaneously for a while, past the power off notification, until the phone prompted to be connected to iTunes to be restored.
    Then I plugged it back into the computer (this is Windows 7, by the way). Sure enough iTunes said it detected a phone in recovery mode, and would I like to have iTunes restore it to factory settings and put on the latest iOS? I sure would, so I did that and waited...
    After that was done, iTunes wanted me to active the phone with Verizon. We had already done that an hour earlier over the phone, but tried it anyway, and it failed. We ignored that failure and went into the phone in iTunes -- it now asked if it was a new phone or if we should restore it -- and the backup from this morning was listed. Phew!
    Finally completed the restore. I noticed that all of the passwords for all apps were lost -- unlike with a normal restore/backup on the same phone -- but everything else (pcitures, apps, etc.) was there. Thank goodness!
    So, if you have upgraded the iOS version and have to replace your phone and the nreplacement has an older iOS verison, then that may explain why your backups appear to be missing...

    Yes, I tried. But nothing is working. I am feeling bad as such a costly phone stop working in 1.4 year ?
    I am just sharing my experience.
    I am not ranting but yes angry as I am eligible for upgrade in Nov 2012 so don't want to pay $149 for replacement as I can upgrade to iPhone 5.
    Apple expert please help me how can I fix it. It's completely software issue.

Maybe you are looking for

  • Using CLOB in 8.1.7

    Hi, Well, everything here seems simple with the use of CLOB. But unfortunately, it springs up a surprise,to me atleast, when compiled. l_clob clob := '<?xml version = "1.0"?>      <ROWSET>      <ROW num="1">      <EMPNO>7369</EMPNO>      <ENAME>SEAND

  • IPhoto Slideshow to iDVD - Audio problem

    I created a slideshow in iPhoto and added music from iTunes. The slidewhow is about 40 minutes long and I set the length of the slideshow to match the music (about 10 songs). I shred the show from iPhoto to iDVD using the Share option. When I preview

  • Text document search

    I have 2 text files that I need to compare a child list and a parent list. The problem is leading zeros in one of the files. For example. Child (600 mb) 123 134 4241 456Parent (1.5 gb) 0000123 00456 000789I have to find which numbers in the child lis

  • JDeveloper 3.0 debugging problem

    I switched JDeveloper to use JDK 1.1.7 and I got a message that the debugger does not support that JDK version. Then I switched back to the original preconfigured JDK1.1.8_JDeveloper. This was done by setting the value in field Project/Project proper

  • More than one records merge into one record

    Hi, I would like to merge multi records into one record. For example program_id campus_code 12345 ABC 56789 ABC 56789 EFG 56789 XYZ 98765 XYZ the output is as follows: program_id campus_code 12345 ABC 56789 ABC EFG XYZ 98765 XYZ How can I get this re