Sound problems after upgrade to OS4

Good morning,
Anyone else who has sound problems while phoning after the upgrade to OS4? I have a 3Gs. Sound while phoning has been reduced to absolute minimum.

Same here as well - I have an iPhone 3GS and noticed this morning, when connected to my in-car bluetooth phone system, if I am running a iOS4 application like TomTom which is multi-tasking in the background, the sound quality is crackly, however if I kill the TomTom apps from the task manager, after a few seconds, sound quality is fine.
Starting up TomTom again, immediately reduces the sound qulaity back to crackling.
Not sure if the iOS4 or TomTom to blame.
If I used a the Speaker option, sound is fine. It appears that only bluetooth is affected.

Similar Messages

Sound problem after upgrading to 10.6.3

I'm not 100% sure, if this is related to 10.6.3 but it occured after upgrading today (as far as I remember).
I often use the headphone with my MacBook - and sometimes I use the normal speakers... it happened earlier, that my computer "forgot" that it has built-in speakers, but plugging in the headphone jack and removing it helped.
But today, after updating to 10.6.3. my MacBook refused to play sounds of movies etc. permanently. Changing the volume displays a "not available" sign, System Prefs don't now anything about built-in speakers.
Restarting the Mac plays the normal boot sound on these very speakers, but even repairing permissions or resetting the parameter ram didn't solve the issue.
I even recognized a red LED light shining out of the headphone socket for a few minutes...
Anyone expereincing the same problem? Or any idea what else I could try?
Cheers
Dirk

Hurray!! Solved!
The QTip was the solution. I couldn't see any dirt inside, and compressed air didn't help either. Also the first round or QTipping wasn't working - but then, gently turning and even more gently pressing turned out to be it.
A little grey color on the white cotton showed, that something definately was not right here. And now it works.
Thanks guys.
P.S. Even though I'm lucky to have one of three german Apple Stores nearby, I'm happy to not needing a new logic board..

Sound problem after upgrading to Yosemite.

After upgrading to Yosemite, Sound driver suddenly stopped working as you see in the image.

There are many possible causes for this issue. Take each of the following steps that you haven't already tried. Some may not apply to your model. Back up all data before making any changes.
1. Start with the steps recommended in this support article. Don't skip any of the steps. It's the starting point for further efforts to solve the problem.
2. Run Software Update and make sure you have a fully up-to-date installation of OS X.
3. If you've installed an application called "Memory Clean" or any other third-party software that is supposed to "clean" or "purge" memory automatically, remove it according to the developer's instructions and restart. You should do that even if the software is not causing the problem, because it's useless.
4. Other third-party software that has been reported to interfere with sound output includes "Boom" and "Samsung Kies." If applicable, uninstall according to the developer's instructions (not by dragging something to the Trash.)
5. If an AirPlay device is selected for sound output from iTunes (or from other applications via third-party software such as "Airfoil"), deselect it.
6. Launch the application "Audio MIDI Setup" by entering the first few letters of its name in a Spotlight search and selecting it in the results (it should be at the top.) Select Built-in Output from the list on the left. If the Mute boxes are checked, uncheck them.
7. If a red light is visible in the audio-out port when sound should be playing, the internal switch is stuck in the position for digital output. You may be able to free it by inserting and removing a mini-stereo jack of the proper size. Inserting any kind of tool in the port may cause damage that won't be covered by the warranty.
If there's no red light, the switch may still be stuck in the headphone position. Try to free it the same way.
8. Disconnect all wired peripherals except keyboard and mouse, if applicable. If more than one display is connected, disconnect all extra ones. Restart and test.
9. If you have a MacBook Air, turn off Bluetooth and restart.
10. Start up in safe mode. Don't log in; just restart as usual when the login screen appears. When you do, make sure the words "Safe Boot" do notappear in the login screen. If they do, the system is still in safe mode and sound won't work.
11. Reset the NVRAM.
12. Reset the SMC.
13. Triple-click anywhere in the line below on this page to select it:
/Library/Preferences/Audio
Right-click or control-click the highlighted line and select
Services ▹ Reveal in Finder (or just Reveal)
from the contextual menu.* A folder should open with an item selected. Move the selected item to the Trash. You may be prompted for your administrator login password. Restart the computer and empty the Trash. Recreate your settings in the Sound preference pane.
*If you don't see the contextual menu item, copy the selected text to the Clipboard by pressing the key combination command-C. In the Finder, select
Go ▹ Go to Folder...
from the menu bar and paste into the box that opens by pressing command-V. You won't see what you pasted because a line break is included. Press return.
14. Reinstall OS X after backing up all data.
15. Make a "Genius" appointment at an Apple Store.

Sound problems after upgrading to 7.1 and Pro

I have recently upgraded to Quicktime Pro and installed the 7.1 update, to create Podcasts at work. The only problem is now that non of my quicktimes will play sound. I have checked all volume control sections and mutes etc, its definitely a problem with the software. Also once a movie plays through, or if I try and use the play controls, other than initially pressing play, the player crashes and have to go to task manager to close it properly. The same occurs when you try and close the program.
I was going to uninstall and try again, but I was worried this might cause problems with the Quicktime Pro info.
Anyone else had these problems or have any advice.
pc amd 2.8 Windows 2000

I'm also having sound problems with Quicktime v7.1 Pro. If I play a .swf file in Quicktime, the video and audio play great. If I play an .avi file, the video plays but there is no sound. If I play a .mov created by Camtasia Studio using either the default compression or the H.264 compression format, the video plays but there is no sound. The graphic display indicates that the audio is present in all cases.
Is there an issue with this new version of Quicktime Pro v7.1?

[SOLVED] Sound problems after upgrading

Forgive me in advance for any vagueness on my part. I confess that I'm not entirely clear on how the sound on my system is set up - I've generally just been taking the path of least resistance, and as long as it works I don't worry about it too much.
I did an upgrade a couple days ago that pulled in a ton of new packages, new kernel, etc. Afterwards my sound is (partly) gone. It seems like maybe PulseAudio is working but Alsa isn't? Clementine, native HTML5 videos in Firefox, and speaker-test all have sound. Mplayer, flashplugin, and aplay do not have sound. I'm plugged into a Creative X-fi. There's also a card on the motherboard, but I don't use that one.
I checked alsamixer and unmuted anything that I thought might be to blame, still no luck.
https://i.minus.com/ibqvIkM70QjWVn.png
Here's the default option in alsa.
https://i.minus.com/idY2usYPGY6El.png
Here's the mixer for the Creative.
https://i.minus.com/ibpRAR9h7SBy2b.png
Here's the audio mixer applet with the various options. Both Creative options are unmuted and turned up.
$ sudo aplay -l
**** List of PLAYBACK Hardware Devices ****
card 0: XFi [Creative X-Fi], device 0: ctxfi [Front/WaveIn]
Subdevices: 255/256
Subdevice #0: subdevice #0
Subdevice #1: subdevice #1
<snip>
Subdevice #255: subdevice #255
card 0: XFi [Creative X-Fi], device 1: ctxfi [Surround]
Subdevices: 256/256
Subdevice #0: subdevice #0
Subdevice #1: subdevice #1
<snip>
Subdevice #255: subdevice #255
card 0: XFi [Creative X-Fi], device 2: ctxfi [Center/LFE]
Subdevices: 256/256
Subdevice #0: subdevice #0
Subdevice #1: subdevice #1
<snip>
Subdevice #255: subdevice #255
card 0: XFi [Creative X-Fi], device 3: ctxfi [Side]
Subdevices: 256/256
Subdevice #0: subdevice #0
Subdevice #1: subdevice #1
<snip>
Subdevice #255: subdevice #255
card 0: XFi [Creative X-Fi], device 4: ctxfi [IEC958 Non-audio]
Subdevices: 1/1
Subdevice #0: subdevice #0
card 1: Intel [HDA Intel], device 0: AD198x Analog [AD198x Analog]
Subdevices: 1/1
Subdevice #0: subdevice #0
card 1: Intel [HDA Intel], device 1: AD198x Digital [AD198x Digital]
Subdevices: 1/1
Subdevice #0: subdevice #0
card 2: NVidia [HDA NVidia], device 3: HDMI 0 [HDMI 0]
Subdevices: 1/1
Subdevice #0: subdevice #0
card 2: NVidia [HDA NVidia], device 7: HDMI 0 [HDMI 0]
Subdevices: 1/1
Subdevice #0: subdevice #0
card 2: NVidia [HDA NVidia], device 8: HDMI 0 [HDMI 0]
Subdevices: 1/1
Subdevice #0: subdevice #0
card 2: NVidia [HDA NVidia], device 9: HDMI 0 [HDMI 0]
Subdevices: 1/1
Subdevice #0: subdevice #0
$ lsmod | grep '^snd' | column -t
snd_hda_codec_hdmi 27848 4
snd_hda_codec_analog 79922 1
snd_ctxfi 97609 3
snd_hda_intel 34194 6
snd_hda_codec 102453 3 snd_hda_codec_hdmi,snd_hda_intel,snd_hda_codec_analog
snd_hwdep 6428 1 snd_hda_codec
snd_pcm 78146 4 snd_ctxfi,snd_hda_codec_hdmi,snd_hda_codec,snd_hda_intel
snd_page_alloc 7426 3 snd_ctxfi,snd_pcm,snd_hda_intel
snd_timer 18934 1 snd_pcm
snd 60156 26 snd_ctxfi,snd_hwdep,snd_timer,snd_hda_codec_hdmi,snd_pcm,snd_hda_codec,snd_hda_intel,snd_hda_codec_analog
Please let me know if there's anything else I can add to help troubleshoot. Being inexperienced with sound stuff, I don't know where to look.
-- mod edit: read the Forum Etiquette and only post thumbnails http://wiki.archlinux.org/index.php/For … s_and_Code [jwr] --
Last edited by youngian (2014-01-03 07:21:28)

Ok, I finally figured it out. Will document here in hopes that it helps others. Please excuse any vagueness or minor inaccuracies, this stuff is not my area of specialization.
As I expected, the key was gaining a better understanding of what roles each package plays. ALSA sits close to the hardware and drivers. It's the thing responsible for actually pumping sound into my sound card and out the speakers. PulseAudio sits on top of ALSA, and handles mixing different audio streams coming in from different sources, plus does a bunch of other fancy stuff if you ask it to. So Pulse mixes stuff into one sensible audio stream and pumps that into ALSA, which handles the hardware. Now one final layer: some legacy applications will only work with an ALSA device, but Pulse doesn't want to share ALSA with anyone - it wants everything to go through Pulse first. So Pulse provides an emulated ALSA device for these applications that looks like a sound card, but actually routes through Pulse. That's what the stuff in asound.conf is doing; setting the system's default audio device to be the emulated Pulse device.
Now to my specific problem. Pulse, for whatever reason, was using the wrong "sink" for audio output. It has several different sinks listed for my soundcard, but only one works. So with asound.conf intact, sound was being routed into Pulse and then out the wrong sink, thus no sound for me. When I added the line to my ~/.asoundrc, I was (I think) actually overwriting the default device so that it was no longer the emulated Pulse device. So even though the Pulse server was running, I was bypassing it and sending all my system sound straight to ALSA. This also explains some weird behavior I was seeing in my web browsers, where I got audio fine from Flash, but not from native HTML5 video.
To fix it, I got rid of my ~/.asoundrc, and left /etc/asound.conf as is. Then I had Pulse list all the available sinks for my sound card:
pactl list sinks
I tested each sink to find one that worked:
paplay /tmp/volumeTest.wav -d alsa_output.pci-0000_01_00.1.hdmi-stereo
Once I knew which one was the correct one, I set it as the default sink:
pactl set-default-sink alsa_output.pci-0000_05_00.0.analog-stereo
And then tested to make sure that Pulse was working, and that ALSA was routing things into Pulse:
paplay /tmp/volumeTest.wav
aplay -D default /tmp/volumeTest.wav

Very strange Sound problem after upgrade.

For the past several months I've been using both onbaord and a second soundcard on my MSI K8N Neo 4 SLI and have had no problems. Yesterday I upgraded from an AMD Atlhon 64 3000+ venice to 3200+ venice and went from a IDE hdd to a SATA 3g/b hdd. Now I can't get sound to work on either soundcard.. I have formatted several times and tried supplied drivers and ones from Creative and MSI. I just can't get the sound to work anymore.. Also I'm powering my SATA drive through Legacy 4pin Molex the same as my previous IDE drive. i can't figure out WHY this is happening, I have the same PSU as before and that should not effect a PCI sound blaster either..

Try the nvidia drivers
http://www.nvidia.com/content/drivers/drivers.asp
Platform Nforce Drivers / Nforce Audio Driver..
that supports your board

Got problems after upgrade to OS4? try this.....

For all of you out there who are having problems and are still searching for answers and havn't found solutions, then try this. Hook up your phone back to itunes and do a factory reset, and set the phone up as BRAND NEW, not restore.
This is gonna be a little more time consuming but i think it will correct alot of problems. When its all done, you'll have a phone basically out of the box with OS 4.0 on it. It might ask you to do a carrier update if available from your cell phone provider.
Itunes then can re-sync all your stuff that you still have in itunes, including the re-install of your apps, music sync, photos, etc. You will lose your camera roll pics. And if you allready sync your contacts from another source, then you won't have the problem of re-entering them.
I initially just did a simple upgrade, i noticed a couple of odd ball problems later on. I did the factory reset and brand new setup, its been over 24 hours and she's purring like a kitten.

Hello,
first i would recommend backing up somewhere your camera roll pics because they will be gone, and we hope you have your contacts sync with google or similiar, and calender with google. Or else you'll have to enter all that stuff in again.
I will assume you upgraded to os 4 allready, and times are not that great. Ruling out any hardware issues, lets say your phone was working great with the previous firmware.
Anyways, when u hook up your phone to itunes and in the same section where you pressed the button to upgrade it, press the button below it, this will start the reset procedure. Let it do what it does, eventually it will ask u, if u want to set the phone up as 'brand new' or restore from backup. Select 'brand new', it will continue and finish up. When it finishes, its like you just bought the phone with OS4 on it all ready. Brand new condition. This process is very quick, takes less than 15 minutes. You might get a notice of a carrier update either in itunes or the phone itself, accept it.
You do not need a new apple id, nothing here changes.
At this point in itunes the default sync settings might have changed, all you music is still listed in itunes, your apps are still listed in itunes, your photos are here also. You can start the procedure to sync all your stuff. This will take the longest. It will copy your music, optimize your photos, and re-install your apps.
You can also do the settings to sync your contacts with google, or similar service. If u don't then you should start doing this since this way you'll never ever lose or have to enter your contacts again. All you need is a gmail account.
Same applies for syncing iphone calender with google calender. For calendar, follow instructions here...
http://www.iphonedownloadblog.com/2009/06/30/how-to-sync-google-calendar-with-ip hone-calendar/
works great.

Sound problems after upgrading

Hi,
After installing the pay upgrade on my iPodTouch last week I can't control the volume. It plays everything on max. There's no way I can use my touch now without losing my hearing. What gives?
thanks
alf

Yeah, a 32 gig.
It's clearly stuck, but no matter what I try, I can't get it to lower. I thought maybe changing the volume limit in the music settings would fix it, but alas, no.
I just don't want to have to reset it, and lose everything on there, although I suppose in the end that's what I might have to do.
Anyway, thanks for your reply.
alf

Problems after upgrade: Leopard to Leopard no longer works

My sister upgraded to Leopard on her iMac(c2d) to Leopard yesterday. Earlier in the day we were able to do video chats with a number of people(her machine Tiger to Fathers machine Leopard). However, since upgrading, we've experienced weird behavior for video chats. Basically in her window she won't see her image(the small one), and I don't see her at all. We've tested this out with a number of other iChat accounts and get the same results. Btw, all machines that are chatting with her are using Leopard. Also, all other forms/capabilities work: screen sharing, sharing of pictures, audio chats.
Anyone out there have similar problems after upgrading from Tiger to Leopard? I have done the usual adjustments of bandwidth and QT settings, as well as restarts. What else should I try?
tia,
n

I finally resolved this problem: I think the issues/steps would be helpful for anyone who experiences iSight off or not working problems after upgrading to Leopard(then to 10.5.1) on a intel 20" iMac :
Problem:
-If you have an internal iSight on an iMac and your camera works fine in Tiger
-If you upgrade to Leopard
-If Chat camera doesn't show your image (iSight off) even though the green light is on
-You can see the other persons video on iChat
-Your friends can here you and you can share screens, files, etc.....everything but have them see you
These are the initial steps I took:
- Deleted the pLists(or stored preferences for the Application) described at the top of this thread
- Was told it might be slow internet connection so did various things: disconnected other computers, changed wireless to "G" only
- Specifically Opened of ports spec'd for Leopard on router (even though I hadn't needed to do this under Tiger)
- Tried chats with various people on various fast/slow networks
- Restarted all aspects of the network: router, wireless access point, computer
- Checked to see if the iSight was shown in 'System Profiler'. It was found in 'About This Mac->More Info->System Profiler->USB'
- Clicked Video icon in iChat Buddies window(to the right of your name) and coudn't see my image
- Opened 'PhotoBooth' and coudn't see my image(black screen)
- Opened iMovie and couldn't capture video via the iSight(black screen)
- Opened iChat->Preferences->Video and couldn't see my image
- Validated that 'Camera is Enabled' in iChat->Video->Camera is Enabled
If you are experiencing a similar problem with you built-in iSight, I would probably focus on the last 5 things that I did. What they showed me was that the iSight was just not capturing video even though it was capturing sound in 3 different applications.
The solution to iSight Off or iSight Not Responding or No Video is......reset your computer! I had thought my sister performed this but it turns out she hadn't. Here's the link to this procedure:
http://docs.info.apple.com/article.html?artnum=303446
Very easy to do though: Power off computer and unplug all cables, including power cable for at least 15 seconds. Plug everything back in and power up the computer and retry clicking on the 'Video' icon next to your login name. If you see yourself then...problem is solved.
While I eventually found posts in several other forums, it took me the better part of a week. To try this simple step. I wish I had done so straight away. Oy. I guess I learned a lot about ports, speed etc.
I hope this helps.

I have problems after upgrade my firefox

I have problems after upgrade my firefox
<i>(Suspected spam link removed by Moderator. Please read the [[Forum rules and guidelines]] -m)</i>

Hey there Noel,
It sounds like you are unable to activate your iPhone after you reset it. I recommend the steps from the following article to help you get that resolved:
Get help activating your iPhone
If your carrier provided a SIM card, make sure it's in your iPhone.
Restart the iPhone.
Try to reach the activation server another way, then try to activate.
Try connecting to a known-good Wi-Fi network if you can't activate using a cellular data connection.
Try connecting to iTunes if you can't activate using Wi-Fi.
Restore the iPhone.
Check the system status for iOS Device Activation. If the iOS Device Activation status isn't green, try activating your iPhone later.
If you receive an alert message when you try to activate your iPhone, place the iPhone in recovery mode and perform a restore. If you still can't complete the setup assistant due to an activation error, contact Apple for assistance.
Thank you for using Apple Support Communities.
All the best,
Sterling

Problems after upgrade bios to v4.3 - P67A-GD65

Hi to everybody,
I was having a problems after upgrade bios to v4.3 of my mainboard P67A-GD65.
After upgraded bios version (FW) its interface was changed and seemed better. also some specifiactions upgraded that i am now able to follow information of bios in my windows. with Control Center.
1) first of all after bios upgrade XMP memory section can only be enable şf ş choose OC geniue on. but with this my cpu warm till 98C degree. because i have only stock cpu cooler of intel.
in normal mode xmp can not be activated so that my memory that corsair vengeance dd3 1600mhz works at 1333mhz only.
Also there was information about what is new in this version of bios fw as:
- Enhanced PCI-E display card performance.
- Improved memory compatibility.
2) second problem that i have i wanted to turn cpu leds which were located above cpu slot blue leds. once i turn them off and it is ok. but when shutdown computer and restart it turn on itself.
so may be there have benn occured a problem that mb can not save edited settings correctly?
3) For last i could not find Winki 3 OS/linuz anywhere is there a link to it to integrate to my mb?
Thanks for your replies from now on.
Greetings.

Quote from: momosala on 02-April-13, 17:54:22
I think you had better to flash back to beta 4.39 bios, here : https://forum-en.msi.com/index.php?topic=164135.msg1214789#msg1214789
And use and install on USB key MSI Forum HQ USB flashing tool from here : https://forum-en.msi.com/index.php?topic=108079.msg800577#msg800577
Flash using method 1.
And tell us if that works.
thank you for reply that fast i will try asap and tell here.
Btw, have you ever face a problem as i wrote above?

Problems after upgrading to iTunes version 6

Hello,
I've been going through the threads a lot since I have had problems after upgrading to iTunes v. 6. It looks like a lot of people have had the same issues, and I have tried some things that were recommended. After I upgraded, iTunes would not open. I tried:
1. deleting sidb file
2. doing the msconfig thing suggested in discussion boards
3. going into safe mode and deleting 4 and 6 letter weird files in DOS - I found 3 that I deleted
iTunes worked after this -- then I bought a song and it said my computer was not authorized, after I authorized computer (that never happened before), iTunes worked for about 15 more minutes and then closed down abruptly. I haven't been able to open it since.
I also downloaded Spybot search & destroy and that did not find anything. I am using McAfee, and have scanned for viruses with McAfee and AdAware.
Now, when I restart my computer, a bunch of windows pop up with Chinese/Japanese looking characters and say that device (I think) was not found. I seem to be able to use everything except iTunes and Quicktime. When I open the Task Manager, iPodService.exe and iTunesHelper.exe and qttask.exe are there, but when I click on Quicktime or iTunes the file flashes in Task Manager and then disappears.
I'm not sure where to go from here.
Any help would be apppreciated -- I'd like to be able to open iTunes!

Hello,
I used Nickroo's post:
I was able to get iTunes launched (with the help of Tech Support) in a very unsafe environment. I owe it to those who may need this after me. It will get you going, but you will be extremely vulnerable to internet virus assaults. Please do not use this approach, until you have exhausted every other available solution for your issue in the KB.
There are three Steps 1) Uninstall 2) Disble and 3) Reinstall.
UNISTALL Uninstall iTunes using Windows utility Add Remove Program available in Control Panel.
DISABLE Disable all third party System Services and Startup Items using using MSCONFIG utility as described in Service Document http://docs.info.apple.com/article.html?artnum=302538
RE-INSTALL Re-install iTunes6 + QT7. Launch it under the Selective Startup Option.
It worked ! You realize among other things at this point you have your Antivirus and Firewall disabled. When I started my computer in the Normal Startup Option, iTunes fails to work again. So I have ahead of me the long and ardous task of ruling out the service that is causing conflict with iTunes6. Then work with the software vendor to arrive at a solution.
This seems to have worked so far- I haven't started to go through ruling out what made iTunes not work; I also haven't tried to connect my iPod or burn a CD, so we'll see.
Windows XP

Permission problems after upgrade to 10.5 on early Power PC G5 Tower

Permissions problems after upgrading to 10.5 on a client power PC (early) G5 tower.
Problems include folders that are created on XServe via this client do not allow any one else including this client to access. All other clients running 10.5, which happen to be newer Intel machines do not have this problem. Repairing permissions, updating to 10.5.1, try to manually correct permissions have all failed to repair the situation. All clients log onto the XServe with the same user/password. This client has since been downgraded back to 10.4.9 and has no issues.
The Xserve runs 10.3.9, any help would be greatly appreciated.
We have read through the forums regarding permission problems after upgrading and even tried some tips found here.

You really should check things out first before speaking.
Here are the requirements for 10.5;
Mac OS X v10.5 Leopard requires:
A Mac computer with an Intel, PowerPC G5, or Power PC G4 (867 MHz or faster) processor
512 MB memory or more
A DVD drive for installation
9 GB of available disk space or more
Some features require a compatible Internet service provider, fees may apply.
Some features require Apple's MobileMe service; fees apply.
Allan

Layouts problem after upgrade

Hello, I have a problem after upgrade from 2007 to 8.81 PL 05.
Since we upgrade SAP, the layout changed.
For example, in a credit note if it has 3 lines, in the layout will appear 2 lines in a page and 1 in other page.
if the credit note has 4 lines, in the layout will appear 3 lines in a page and 1 in other page.
What could it be?
Thanks in advance.

Hi!
lines are not duplicated, they just printed on different pages:
- if doc has just 2 lines - printed form is good
- if doc has 3 items, two of them are printed on the first page, 3d - on the second page
- if doc has 4 items, 3 of them are printed on the first page, 4th - on the second page
When we are printing directly from the server everything is working fine. But printing from all Clients gives us this issue that is described above.
SAP re-installation for all users will take too much time. May be exist any other option that we can try?
we really appreciate your help
Natalia

Problem after upgrading to ICS 4.0.4

i have different problem after upgrading my SE Live with Walkman to ICS 4.0. After upgrading, my sd card always full. I have try to remove some files but after that it full again. Finaly i found that there are tumbnail file with size precisely same with my empty space. I delete that file, but the empty space not recover, its only recover after unmounting sd card. But its not hold for long time, after one minutes its happen again, my sd card is back fully again, and the same file is back to exist. Please help me, is that a virus or bugs from ICS?? i very frustation with this case
thanx for your help

Do you have many pictures?
Have your tried to reinstall the phone software using SUS to check if the problem remains?
http://www.sonymobile.com/gb/tools/update-service/
- Community Manager Sony Xperia Support Forum
If you're new to our forums make sure that you have read our Discussion guidelines.
If you want to get in touch with the local support team for your country please visit our contact page.

Sound problems after upgrade to OS4

Similar Messages

Maybe you are looking for