SPARC10 not booting after 2.5.1 Recommended Patch Cluster Install

Hi everyone,
Just finished installing the "latest" patch cluster on my ancient SPARC10, and now it doesn't boot. Here's what I see:
ok boot /iommu/sbus/espdma@f,400000/esp@f,800000/sd@0,0
screen not found.
Can't open input device.
Keyboard not present. Using tty for input and output.
SPARCstation 10 (1 X 390Z55), No Keyboard
ROM Rev. 2.25, 112 MB memory installed, Serial #6332710.
Ethernet address 8:0:20:12:7f:99, Host ID: 7260a126.
Rebooting with command: /iommu/sbus/espdma@f,400000/esp@f,800000/sd@0,0
Boot device: /iommu/sbus/espdma@f,400000/esp@f,800000/sd@0,0 File and args:
not found: abort_enable
not found: abort_enable
not found: tod_validate
not found: tod_fault_reset
krtld: error during initial load/link phase
Memory Address not Aligned
Type help for more information
ok
At first I thought I had a RAM problem. I've swapped RAM, but that didn't make it boot. I then thought I had a system board problem. I've swapped that as well, and still no dice. I wish I'd have kept the list of patches that successfully installed like my gut told me to, but I didn't. Searching Google and the Sun websites didn't turn up any fixes to the problem, so I'm hoping I can find help here.
Did the patches clobber something the machine needs to boot? I believe the OS disks are mirrored, and I've tried booting off each submirror, but the result is the same.
If I can avoid booting off of CD-ROM, that would be ideal since I don't have an external CD-ROM available to boot from.
Thanks for any help!

Ouch !
Haven't seen that one in years !
It's your choice of that ancient Operating Environment, combined with a cpu faster than 419MHz.
I hope you still have the extra OECD disk that was packed with that system when it was first shipped from Sun.
Otherwise you may just be out of luck with using Solaris 2.5.1
Here's a link at a non-Sun 3rd party web site to SRDB document *20576*
http://www.sunshack.org/data/sh/2.1/infoserver.central/data/syshbk/collections/intsrdb/20576.html
Perhaps MAAL and haroldb can contribute their thoughts on this.

Similar Messages

Mac Mini will not boot after Security Update 2008-007

Hello,
A G4 Mac Mini machine I was asked to take a look at will not boot after the owner (succesfully) installed Security Update 2008-007 from Software Update. Booting always hangs at the blue screen after the Apple logo, and booting in verbose mode reveals that WindowServer is crashing repeatedly. Permissions and filesystems have been repaired, PRAM reset, etc. Safe boot also exhibits the same problem, but it is possible to boot to single user mode. Hardware checks out fine with diagnostic utilities.
Any suggestions on how to fix this? Unfortunately, backups are not available (it's not my machine =).

Hi Arkku , and a warm welcome to the forums!
I'd certainly give Sig's advice a try first.
If that should fail...
applesetupdone...
This was Posted by: JoseAranda at September 9, 2006 3:48 AM
"OK, restart your computer, hold down Command-s and type in the following:
/sbin/fsck -fy Enter
/sbin/mount -uaw Enter
rm /var/db/.applesetupdone Enter
# The rm command is the remove command which deletes the file.
# Robert: I'd rename the file via: mv /var/db/.applesetupdone /var/db/.applesetupdone.old
reboot Enter
Once you've done that the computer reboots and it's like the first time you used the machine. Your old accounts are all safe. From there you just change all other account passwords in the account preferences!!
end of posted by: JoseAranda"
Reset OS X Password Without an OS X CD...
http://theappleblog.com/2008/06/22/reset-os-x-password-without-an-os-x-cd/

MacBook Pro will not boot after software update

MacBook Pro will not boot after doing an Apple Software Update (of course they will not help you). MONEY, MONEY, MONEY is the name of the game. They can cause your computer to crash and still charge you!
Does anyone have an answer to why my computer is showing a little gear spinning for hours? I have tried several things with NO luck.
Thanks-

Run through the list of fixes here
Step by Step to fix your Mac

HP Pavilion 15-n268sa will not boot after windows update (windows 8.1)

After a series of windows update (windows 8.1) my HP Pavilion 15-n268sa will not boot up, no fan noises, no lights no nothing.
I have tried a "hard reset" a number of times with no success.
When the battery is present the white LED flashes 3 times when the power button is pressed.
Please please help.

Hello Cuffy,
Welcome to the HP Forums!
I understand you notebook will not boot after a series of Windows updates.
Can you tell me if you are able to access the HP Recovery Manager by repeatedly tapping the F11 key while the notebook turns on? If you can access this, try doing a system restore to before you installed the updates. If not I would suggest you go through this document: Computer Does Not Start and the LEDs Blink or the Computer Beeps.
If it's the Caps Lock light that is blinking this document will tell you exactly what the error is (spoiler: 3 beeps is a memory failure). This could also explain the failed updates. The updates are stored in the RAM before being applied to the operating system.
You can try reseating the RAM, or using only 1 of the RAM cards, as you have 2x4GB cards. If it still doesn't work with 1 card, try the other card to confirm it has failed.
You can replace defective cards via HP Phone Support if covered under warranty or at the HP Part Store if not covered. You can contact HP Technical Support at 1-800-474-6836 in North America. For all other regions click here.
Hopefully this information helps!
Please click the "Kudos, Thumbs Up" at the bottom of this post if you want to say "Thanks" for helping!
Please click "Accept as Solution" if you feel my post solved your issue, it will help others find the solution.
The Great Deku Tree
I work on behalf of HP.

Not Booting after recent Security Patch/Java update

My wife has experienced what many have experienced with the recent update.
MacBook not booting after update (i.e. - "I have no name!")
I have tried everything posted on this topic since 2/13/09, but without any success. Does anyone have the fix for this yet?
Things I have tried:
* I can boot in safe mode (holding "Shift" while restarting)
* I cannot boot from an install disk(s) (holding C while restarting) - I have both a black one from purchase, and two gray ones with purchase from MiniMac
* Booting with verbose - gets stuck at same place as everyone else
Operating in safe mode:
* I can run DU and "repair" drive
* I can see and access the CD/DVD
* I cannot see drive in target drive mode (doesn't ever connect the 2 systems)
* I downloaded the update files from apple and reinstalled them individually (via USB ext Drive) with a reboot in between
* I attempted to update & archive, but I cannot run install CD from any systems disks (see above)
Has anyone figured out how to fix this yet?

Same problem than the other guy who is not mentioning the update in the title.
Powerbook 1.67.
System log said "No user defined computer name" and "using blah blah name" or so.
Mac Os X report (for apple) says:
Unresolved kernel trap(cpu 0): 0x300 - Data access DAR=0x000000003900FF1C PC=0x00000000008FC020
Latest crash info for cpu 0:
Exception state (sv=0x4299D280)
PC=0x008FC020; MSR=0x00009030; DAR=0x3900FF1C; DSISR=0x40000000; LR=0x008FE348; R1=0x2C47B9F0; XCP=0x0000000C (0x300 - Data access)
Backtrace:
0x008FE348 0x008E0014 0x002E9A80 0x002EB94C 0x0008C248 0x00029234
0x000233F8 0x000ABEAC 0xFF9BA29B
Kernel loadable modules in backtrace (with dependencies):
com.apple.ATIRadeon9700(4.1.8)@0x8d8000
dependency: com.apple.iokit.IOPCIFamily(1.7)@0x48d000
dependency: com.apple.iokit.IOGraphicsFamily(1.4.2)@0x85a000
dependency: com.apple.iokit.IONDRVSupport(1.4.2)@0x87e000
Proceeding back via exception chain:
Exception state (sv=0x4299D280)
previously dumped as "Latest" state. skipping...
Exception state (sv=0x43D0D000)
PC=0x9000AF48; MSR=0x0200F030; DAR=0x0ECA77FE; DSISR=0x42000000; LR=0x9000AE9C; R1=0xBFFFD6C0; XCP=0x00000030 (0xC00 - System call)
Kernel version:
Darwin Kernel Version 8.11.0: Wed Oct 10 18:26:00 PDT 2007; root:xnu-792.24.17~1/RELEASE_PPC
panic(cpu 0 caller 0xFFFF0003): 0x300 - Data access
Latest stack backtrace for cpu 0:
Backtrace:
0x000954F8 0x00095A10 0x00026898 0x000A8204 0x000ABB80
Proceeding back via exception chain:
Exception state (sv=0x4299D280)
PC=0x008FC020; MSR=0x00009030; DAR=0x3900FF1C; DSISR=0x40000000; LR=0x008FE348; R1=0x2C47B9F0; XCP=0x0000000C (0x300 - Data access)
Backtrace:
0x008FE348 0x008E0014 0x002E9A80 0x002EB94C 0x0008C248 0x00029234
0x000233F8 0x000ABEAC 0xFF9BA29B
Kernel loadable modules in backtrace (with dependencies):
com.apple.ATIRadeon9700(4.1.8)@0x8d8000
dependency: com.apple.iokit.IOPCIFamily(1.7)@0x48d000
dependency: com.apple.iokit.IOGraphicsFamily(1.4.2)@0x85a000
dependency: com.apple.iokit.IONDRVSupport(1.4.2)@0x87e000
Exception state (sv=0x43D0D000)
PC=0x9000AF48; MSR=0x0200F030; DAR=0x0ECA77FE; DSISR=0x42000000; LR=0x9000AE9C; R1=0xBFFFD6C0; XCP=0x00000030 (0xC00 - System call)
Kernel version:
Darwin Kernel Version 8.11.0: Wed Oct 10 18:26:00 PDT 2007; root:xnu-792.24.17~1/RELEASE_PPC

HT4623 iPhone 4s will not boot after trying to install ios7 beta 4. Stops at apple logo with progress line under it. how can I reset it or get it back up to do a restore then try the iOS 7 beta 4 install again. Issue was probably caused by disconnection

iPhone 4s will not boot after trying to install ios7 beta 4. Stops at apple logo with progress line under it. how can I reset it or get it back up to do a restore then try the iOS 7 beta 4 install again. Issue was probably caused by disconnection

Obviously since you have iOS 7 you're a developer. As a developer, you signed a NDA with Apple not to discuss the iOS on a public forum. Please log in to the Developer Forum using your credentials and ask for help there, lest you risk having your credentials terminated.
Thanks, and best of luck to you.
GDG

Macbook Pro Will Not Boot After Full Timemachine Restore

Hope someone can help. I upgraded my HD and attempted to restore from time machine. Everything appears to have worked well and the restoration was a success according to what the computer says. However, when I go to reboot I hear the startup sound then the apple pops up on the screen followed by a kernal panic error and the black box telling me that I need to hold down the start button and restart. I've tried resetting the pram, reinstalling from TM again and a couple of other things but it won't start up. I tried doing a clean install and it worked fine then I migrated files from my TM backup and that worked fine as well. However, that's not what I'm looking for, I wanted to get the machine exactly the way it looked before the upgrade and I thought TM was supposed to do that. I've read other forums were people have done it with no problems and am completely stumped at why it is not working. If anyone can shed some light I'd appreciate it.

I booted with the CD and after selecting the language, went to the utilities pane and used the partition feature.
Last night in desperation, I booted back to the CD and once again told it to do a full restore from TM. This was the third time that I had done it so far. The previous two times I had gone into the partition feature and partitioned the drive first. This time I skipped that step and just told it to restore from TM. It said if it did this it would erase everything on the drive. I agreed and let it do its work. This morning it once again, as in both previous times, said it had restored from TM successfully. I told it to restart and lo and behold, it booted and everything is just as I had it on the other drive.
Needless to say, I'm confused but happy. I just wish I knew why it would not boot after restoring the previous two times? Maybe it just wanted me to spend more money:) I tried booting today only after I had gone to frys electronics and bought a SATA to USB cable and cloning software.
Anyway, thanks for your help and if anyone knows why it wouldn't boot, let me know. It would be good to know for the future just in case. For anyone else having this trouble, keep trying. Third time was a charm for me.

My mac mini does not boot, after backing the enire system onto an external drive with Carbon Copy Clone

My Mac Mini does not boot, after backing the enire system onto an external drive with Carbon Copy Clone. I had switched the start-up disk back to the original of course. Now all I see is the Apple logo. What should I do? Thanks in advance.

Try disconnecting any external devices, especially hard drives
and try rebooting.
If that doesn't help, then :
If you are running Lion, boot to the Recovery HD and run a
Repair Disk on the OSX partition.
If Snow Leopard, boot to the installl DVD and run Repair Disk.
Also, you may want to bookmark this:
http://reviews.cnet.com/8301-13727_7-57345273-263/troubleshooting-the-boot-proce ss-for-intel-macs/?tag=txt;title
for future reference. It is a pretty good explanation of the
Mac boot process and how to identify where problems may be.

Power Book G 4 wil not boot after oz update Snow leapard os

Power book G4 did not boot after Lastesat Mozilla update, Runing snow leapard, message updatenis not compatable with computer tried to delete update, and will not boot from then on?

You can't run Snow Leopard on a PowerBook G4.
Please straighten your story out.

My mac book pro is not booting after sleep

My mac book pro is not booting after sleep...Pls anyone help me!!!

Hello adibah2731,
We've an article that proivdes a host of useful tips that can get your Mac booting up again.
Troubleshooting: My computer won't turn on
http://support.apple.com/kb/TS1367
Cheers,
Allen

My Laptop B490 not booting after bios update

My laptop not booting after updating bios i used windows 8 OS.
I downloaded Bios from following link.
Bios Download Link
After updating bios, system restarted automaticaly, after that only power led is glowing, screen stays blank.
Help me solve it.
Solved!
Go to Solution.

hi sathish291
Welcome to the Forums.
Can you try the following:
1. Power down the machine, remove the AC adapter and battery.
2. Hold the power button for 30secs and reconnect the AC adapter only then turn the computer ON.
If the machine still doesn't power up normally and boot into WIndows then it's likely that something went wrong (could be a bad BIOS flash or an internal component might have gone defective during or after the BIOS update). In this case, you may need to contact lenovo on how to go about getting the unit serviced.
Support phone list
Regards
Did someone help you today? Press the star on the left to thank them with a Kudo!
If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"! This will help the rest of the Community with similar issues identify the verified solution and benefit from it.
Follow @LenovoForums on Twitter!

MB.ACT light OFF --- after Solaris 9 recommended patch cluster applied

After applying the recommended patch cluster to several SunFire V210s/V240s the "system ready" or "activity" light on the front panel no longer illuminates. The systems come up fine and are fully functional, just no light.
While this has absolutely no impact on usability it is a bit disconcerting for the folks in the server room when glancing at the rack and not seeing the typical green light.
I first noticed the problem in mid 2007 and have tried patch clusters as recent as last month, but the light remains out.
One interesting discovery is that if I reset (hard) the ALOM module the light comes back on. However, if the system is subsequently rebooted for any reason the light does not come back on...
If anyone can shed some light on the issue I would greatly appreciate it!
-Sap

continued.
I removed patch 138217-01 (svccfg & svcprop patch) and re-applied it.
Then, after booting into S-mode, I tried to continue with the broken patch 139555-08 (kernel).
It ends with
! root@jumpstart:/var/spool/patch # patchadd 139555-08
Validating patches...
Loading patches installed on the system...
Done!
Loading patches requested to install.
Preparing checklist for non-global zone check...
Checking non-global zones...
This patch passes the non-global zone check.
139555-08
Summary for zones:
Zone oem
Rejected patches:
None.
Patches that passed the dependency check:
139555-08
Patching global zone
Adding patches...
Checking installed patches...
Executing prepatch script...
Installing patch packages...
Pkgadd failed. See /var/tmp/139555-08.log.21103 for details
Patchadd is terminating.
! root@jumpstart:/var/spool/patch #the logfile shows
! root@jumpstart:/var/spool/patch # vi /var/tmp/139555-08.log.21103
Dryrun complete.
No changes were made to the system.
This appears to be an attempt to install the same architecture and
version of a package which is already installed. This installation
will attempt to overwrite this package.
pkgadd: ERROR: couldn't lock in /var/run/.patchSafeMode/root/var/sadm/install (s
erver running?): Resource temporarily unavailable
Installation of <SUNWarc> failed (internal error).
No changes were made to the system.Help!
-- Nick

System will not boot when Aironet 802.11a/b/g adapter installed

I have an HP 8000 Elite sff that will not boot after installing the adapter. I am running XP sp3. As soon as I remove the adapter, it boots fine.???

Which adapter ? Aironet 350 or CB21 ?
Do you have another similar adapter to put in the laptop to try ?
Is the problem new ? did it suddenly happen ?
Nicolas.
===
Please rate answers that you find useful

Solaris reboot loop after recommended patch cluster

Hi,
I have a problem with my solaris 10 x86 install on my intel notebook. after installing the latest recommended patch cluster and the necessary reboot my latop stays in a loop.
one of the last lines I was able to see:
panic[cpu0]/thread=fec1d660: boot_mapin():No pp for pfnum=20fff
fec33b4c genunix:main+1b ()
skipping system dump - ....
rebooting...
any ideas ?
cu+thx

This horrible patch caught me out too. I found this and it fixed my problem.
http://weblog.erenkrantz.com/weblog/software/solaris
<snip>
[...at the Solaris boot prompt; enable kmdb, debugging, and single-user
so that you can remove the patch and reboot...]
boot -kds
[...wait for it to boot...]
physmax:w
:c
[...you'll see 'stop on write of'...]
physmax/X
[...you'll see something like the following line:
physmax: bff7f
this is a hex number; add one; so if you see bff7f,
your next line will need to be bff80...]
physxmax/W bff80
:c
[...system will boot and go into single user mode...
now, go toss those patches...]
patchrm 118844-19 120662-03 118345-12 118376-04 \
118565-03 118886-01 119076-10 118813-01 \
118881-02 120082-07 119851-02
shutdown -i6 -y -g0 "sun should test their patches"
</snip>

Mic Jack not working after Driver Update, Console unavailable, can't install

LMic Jack not working after Driver Update, Console unavailable, can't install? I've had nothing but problems after downloading the latest updates via the auto-updater.
I'm currently using the Creative SB X-Fi Pro Series card. I've had it for close to 6 months and have not had any issues until I ran the auto-updater last night, and while it downloaded over 250Mb of updates, all of them failed to install as described below.
I'm running on Windows Vista Ultimate, 64-bit
My main issue is the fact that my microphone is no longer working. I've done a lot of searching and I think the problem has to do with flexijack not being a microphone jack, but instead is an 'in-line' jack. I can no longer find my audio control console, which allows me to switch between gaming and entertainment modes, ect. The solution I found on the KB says that you can switch the blue jack on the back of the card from an in-line jack to a mic jack within the Audio console. I tried downloading it, but while going through the install, I get an error saying the files could not be found and a prompt which asks for a disk or file location. The same thing pretty much happens with all of the items I attempted to download and install.
I was able to run console fine, as well as use my mic yesterday before I attempted any updates. I attempted the updates because since I've had the card, I've had issues where after I exit a game, all my sound will become crackly and static. Before, I would simply open up the console and switch back-and-forth from gaming to entertainment, which would fix the problem most of the time. If that didn't work, a restart would fix it, but now I've opened up a whole new set of issues.
Any help would be greatly appreciated.
I also want to say that the support tickets should not require a serial number to submit a new ticket. My product is registered, so I got rid of the box which contains all that information, leaving me at the mercy of these boards...

Hello all. Fisrt of all, this are my specs: Yoga 2 pro 13". WiFi card: Intel(R)Dual Band Wireless-AC 7260. I bought it from Best Buy on November 27, 2014. If you aquired your Yoga before this date, you may have the single band WiFi card. As many of you have experienced, I also had a bunch of issues with my WiFi connectivity and this is how I was able to solve it. At least it has been a couple of days that I haven't had any issues. The first symptom was the usual connection drops every X amount of time. For me it was about every 2 hours. I first unchecked the "Allow the computer to turn off this device to save power" option in the Power Management tab of device manager and disabled U-APSD support in the Advanced tab of device manager. This action did not solve the problem. I then downloaded and updated the driver from the Intel web site (http://www.intel.com/p/en_US/support/detect) and this seemed to solve the drops; however, a new problem arised: Everytime my Yoga would wake up from sleeping mode, all my wifi networks were gone and the adapter showed as disabled in Device Manager. I would have to anable it to have my networks back. It was a solution but a pain the butt to have to do this everytime. After hours of reading post after post in several forums, I read a repy from Lenovo asking to try leaving the "Allow the computer to turn off this device to save power" CHECKED if you were using the latest version of the driver. I went back to device manager and checked it back and that seems to have solved the problem. So far I haven't had any drops and everytime my laptop comes back from sleeping mode the WFi connection is still there! Here is a recap of how everything ended up: -The driver version I installed is 17.1.0.19-The driver date is 7/21/2014-In device manager|Advanced, U-APSD support is Disbled.-In device manager|Power Management, "Allow the computer to turn off this device to save power" is checked. Hope this helps somebody else.

SPARC10 not booting after 2.5.1 Recommended Patch Cluster Install

Similar Messages

Maybe you are looking for