SpeedGrade 2014.2 will not send output via BlackMagic Intensity Pro HDMI to my external monitor.

I occasionally can get a few pixels near the left side of the monitor, and 2014.1 would display the lower half of the frame, but now, after the 2014.2 update, I can't even get that much. Premiere is monitoring perfectly. Any suggestions welcome!

I am having the same problem. I am on Speedgrade version 2014.1 currently and it won't output to either of the monitors I've tried. Both are connected via HDMI.
One is a 22' ASUS monitor, which reads "Out of Range" when I connect it to my blackmagic Intensity Pro output. From what I've read this has to do with the frame size coming out of SP being too large for the monitor.
Next I tried to output to a 50' HD TV. I don't get the "Out of Range" message on this one, instead the monitor is black with an occasional flicker when I hover over a clip or an option in Speedgrade. By flicker I mean the screen flashes a garbled purple mess for less than a second, then goes black again.
I'm running the Creative Cloud Suite on a Mid 2012 Mac Desktop with a 2 x 2.66 GHz 6-Core Intel Xeon processor, 52GB of RAM, and ATI Radeon HD 5770 1024 MB graphics card. OSX version 10.8.5.
Been waiting for this capability for a while, any advice would be much appreciated.
Thanks!
Josh

Similar Messages

  • AU Lab will not send output to Focusrite Saffire 6 USB - Suggestions?

    Macbook Air 13" (2012)
    AU Lab will not route audio to Saffire 6. I'm creating an EQ for the overall audio on my Mac - if I set to output through internal speakers, it works perfectly - but if output is set to Saffire 6, AU Lab won't even recognise an input from Soundflower, let alone send an output to the interface.
    Ideas?

    Hey all, first I am SOOO glad I found this as I was going nuts trying to figure this out.. The post from addressler is totally correct, however I just wanted to chime in that if you are using ARC 2 room correction plugin within AU Lab, you should not forget to change your DAW input/output to "Soundflower (2ch)" as well so your mixes are going through the plugin, but bouncing of your audio is not being affected. I am using AU Lab to listen to music, produce music in my DAW and correct my room acoustics so this is important.
    Additionally, and perhaps this is an anomaly on my system, but I noticed that I had duplicate (slightly delayed) audio playing causing some phasing issues on playback when using soundflower. I fixed this by leaving all routing the same, but simply quitting Soundflower. I know it sounds crazy, but I quit soundflower and still have my Preferences audio ouput, Au Lab input, and DAW (Logic Pro 9) input AND output set to Soundflower (2 ch) and it works like a charm.
    I have AU Lab set to open on startup. Only thing to remember is that when it comes time to track or use your interface to record into the DAW, you must switch the DAW input/output to Saffire (or interface of choice), otherwise your interface is merely your playback device (Soundcard) and does not offer any preamp input options.
    Hope this helps someone!

  • Blackmagic Intensity Pro problem plackback on external LCD TV

    Hi there,
    Recently installed Intensity Pro card on my Mac Pro and trying to work on FCP6. I use a 1280x720 9 sec footage for testing but there's a problem to playback on a external LCD TV via HDMI cable. The playback on FCP canvas plays fine but the LCD TV just showing a still image. I've tried to test on a SD 720x480 footage which works fine both on FCP canvas and LCD TV even a general CRT 4:3 TV. Sure I have select the Video Playback under View to "Intensity HDTV 720p 60". Are there any other settings need. Will anyone knows what happen or need any settings? Please advice.
    Many Thanks.
    Kory

    Kory - the BlackMagic card is temperamental.
    With FCP, I've found that if I capture using the card, for a few seconds, that the output to the HDMI monitor gets 'fixed'.
    Or, sometimes it will just start working on its own. Maybe after I stop and re-start FCP.
    I even returned my card for replacement. Unsure why they have such issues. But once you figure, by trial an error, a technique for getting the display to work, it does basically work. It's just quirky.
    With Motion output, sometimes I have to use the wrong output rate to see the output, and - then suddenly it will decide it wants the correct output rate.
    But, I'm going out at 1920 x 1080 - and haven't tried other resolutions.
    Good luck. Try complaining to BlackMagic and see if you can escalate the problem up the food chain. Maybe if enough complain they will fix it (they were telling me that it wasn't supposed to display 1080p, but it certainly does - well, somehow converted to 1080i by the card or by FCP).
    One other thing you might try, is an HDMI switch from monoprice. Might help with locking on the hdmi output. I use one of those for monitoring from hdmi input of camera, and I seem to remember playing with it while dealing with the no picture, or still picture issues of HDMI output to my monitor.

  • Despite following all the requested protocols elements 9 will not send photos via photomail

    I had this problem once before in elements 8 and I cant remember how the problem was resolved in the end. I've just replaced my PC, so had to re-download elements 9 . This particular copy didn't automatically import my pictures as usual and once I got over that problem immediately ran into the photomail refusal  
    I have gone through preferences/sharing and chosen windows live mail ( I'm on win 7) managed to import my contacts  but I just keep getting the message
    " elements was unable to finish your e-mail - Alternatively use adobe e-mail service! . I did try there method and after waiting half an hour, got one of there
    ridiculously long serial No checked it goodness knows how many times but still it wouldn't work. I do hope someone knows what to do because sending pics is the most important thing (to me) in photoshop

    Hope you have configured the Windows mail on your new PC, because the error you mentioned is received when the Email is not configured on the system.

  • My Photoshop 9 will not send pictures via email. " services are currently unavailable" error 400  e

    Cannot share photos via email, get sign in then "Photoshop services are currently unavilable, try later. error 400.

    You can stop trying. Photoshop.com is dead and gone, as are the things that relied on it, like the downloadable content in the editor and your contact book in the organizer and so on. If you had any photos stored on photoshop.com, you should have received a bunch of emails about their getting moved to adobe revel, but revel is not a direct equivalent to the services that were available in photoshop.com. More info here:
    http://barbarabrundage.com/2013/09/16/pse-8-9-10-cant-sign-in-error-404/

  • IPhone will not send pictures via iMessage

    My iPhone 5 sends and receives text iMessages just fine, but I cannot send any pictures.  
    Whenever I try to send a picture, iMessage indicates at first that the picture has been "delivered".  Then, about 10 seconds later, it changes the status to "not sent".  The picture never goes through.   I can send the picture as an MMS/Text, just not as an iMessage.
    I've tried resetting my carrier/network settings, turning off/on iMessage, rebooting the phone multiple times, removing the SIM card and everything else I can think of without any success.   Has anyone else had this problem?  What did you do to fix it?

    I had the same Problem with my iPad 4th Gen.
    Here is the fix...
    settings > iMessage > turn off
    Now restart the phone, then  back to settings > iMessage > turn it on
    ...and wait for iMessage to activate and check  if you can send a pic.
    It worked for me, I hope you get the same results.
    Good Luck
    Snoop...

  • TS4006 my macpro will send information to my computor but my iphone will not send information to my macbook pro

    When i enter information into my Macbook pro it goes to my phone, but when i enter from my phone it does not go to my laptop

    For your calendar, go to Settings>Mail,Contacts,Calendars>Default Calendar.  Here make sure you have selected a calendar under you iCloud account name as your default.  If you haven't, make this change, then enter a new event on your phone and see if it syncs now.
    If your settings are correct and it still isn't syncing, enter any events on your phone that are not already on your iCloud calendar to your iCloud calendar so it is up to date.  Then go to Settings>iCloud, turn Calndars to Off.  When prompted, choose Delete from My iPhone.  Then after a minute or so, turn it back On and allow your iCloud calendars to sync back to your phone.  Then enter a new event on your phone and see if it syncs now.
    For your notes, save any notes on your phone that are not already in iCloud by emailing them to yourself.  Then go to Settings>iCloud, turn Notes to Off, then after a minute turn it back to On.  Then create a new note on your phone and see if it syncs properly now.

  • What are the FINAL CUT STUDIO capture presets using a "Blackmagic Intensity Pro HDMI PCI Express Capture Card"

    A S-VHS cable and a/v cables are connected to the breakout box. 
    What are the presets:
    1) Sequence Preset?
    2) Capture Preset?
    3) Device Control Preset?
    thanks

    1) Sequence Preset?
    2) Capture Preset?
    3) Device Control Preset?
    Is this realted to your other question? Don't post more than once, please. GEt it right the first time and then wait. Patiently.
    1. Your sequence rpeset will be determined by the production's output taarget, it has nothing to do with the Balckmagic capture unless you alreday know what that will be. And you do, in fact, because VHS only comes in one way. When you bring your fist captured clip into a sequence, FCP7 will aks if you want to confrom the sequence to the clip's settings. Say yes. Done.
    2. Your capture is going to be regular ol' DV. There's no reason to try to use any other advanced codec for VHS. But you probalby hsould have a time base corrector or frame sync in the loop to help correct and stabilize ancient tapes. Your preset if NTSV DV
    3. There is not control for a VHJS deck. So une unctrolled device.

  • MMS is on but still will not send picture messages

    Every now and then I have a problem where my iPhone 4 will not send picture messages. I have checked MMS and it is on as well as cellular data and everything else involving sending or revieving data (except for mobile hotspot, but that's irrelevant).
    It will send pictures via iMessage (I sent a picture to an iTouch)
    it will not send pictures via text message.
    it WILL send text messages.
    turning WiFi off or on does not affect outcome
    turning MMS off to try to send via iMessage through WiFi results in the picture icon going away
    I've tried turning the phone on and off.
    I'm thinking there might be an error with the SIM card, where it may not think I can send picture messages...
    When sending to someone who has an iPhone, it will not try to send via iMessage it goes straight to text message.
    nothing works
    please help
    thanks.

    nevermind, I got it to work. Still don't know what happened, though...

  • My iPhone 5 will not send photos but will send text. I went to settings and everything seems good to go but I cannot send photos to anyone via messages...please help

    My iPhone 5 will not send photos but will send text. I went to settings and everything seems good to go but I cannot send photos to anyone via messages...please help

    When you said you went to Settings and everything seems good. Does that mean the MMS was turned on? If so, and this is only being experienced when dealing with SMS/MMS, then you should contact your carrier to have them check to make sure your account is provisioned for MMS, and that everything is alright with your account. SMS/MMS is a carrier function.

  • TS3899 iPhone 5 email will not send however emails sent via Pages or yahoo are sending ok? Help

    iPhone 5 email will not send however emails sent via Pages or yahoo are sending ok? Help

    I inserted the code and i am still getting the same error. Here's what i'm getting.
    Developer Details:
    E-mail couldn't be sent. Error returned: authentication failure [SMTP: Invalid response code received from server (code: 535, response: 5.7.3 Authentication unsuccessful)]. (EMAIL_FAILED)
    tNG Execution Trace - VIEW
    * tNG_insert.executeTransaction
    o STARTER.Trigger_Default_Starter
    o tNG_insert.doTransaction
    + BEFORE.Trigger_Default_FormValidation
    + BEFORE.Trigger_Registration_CheckUniqueUsername
    + BEFORE.Trigger_Registration_CheckPassword
    + BEFORE.Trigger_Registration_PrepareActivation
    + tNG_insert.prepareSQL
    + tNG_insert.executeTransaction - execute sql
    + tNG_insert.postExecuteSql
    + AFTER.Trigger_Registration_AddDynamicFields
    Error--> + AFTER.Trigger_ActivationEmail*
    + ERROR.Trigger_Default_Insert_RollBack
    * tNG_insert.getRecordset
    * tNG_insert.getFakeRsArr
    * tNG_insert.getLocalRecordset
    * tNG_insert.getFakeRecordset
    * tNG_insert.getFakeRecordset
    Are there any other file I can alter for authentication? Or perhaps i need to insert the code sting I was given into another file?

  • Thunderbird will not send or receive email in Windows 8.1 unless I re-install. The next time I open Thunderbird it is again broken.

    Thunderbird will not send or receive email in Windows 8.1 unless I re-install it. The next time I open Thunderbird it is again broken. So, I have to repeat the un-install / re-install process. Currently I am using Version 31.0, but this was happening the the previous version as well.
    Here are some of the messages in the error console:
    Could not read chrome manifest 'file:///C:/Program%20Files%20(x86)/Mozilla%20Thunderbird/chrome.manifest'.
    Could not read chrome manifest 'file:///C:/Program%20Files%20(x86)/Mozilla%20Thunderbird/extensions/%7B972ce4c6-7e08-4474-a285-3208198ce6fd%7D/chrome.manifest'.
    Timestamp: 8/3/2014 8:02:29 AM
    Warning: mutating the [[Prototype]] of an object will cause your code to run very slowly; instead create the object with the correct initial [[Prototype]] value using Object.create
    Source File: resource://gre/components/steelApplication.js
    Line: 783
    Timestamp: 8/3/2014 8:02:57 AM
    Warning: Use of getPreventDefault() is deprecated. Use defaultPrevented instead.
    Source File: https://www.mozilla.org/thunderbird/js/jquery/jquery-1.5.1.min.js
    Line: 16
    Thanks for the help.
    Joe

    That really sounds like anti virus scanning to me. Try rebooting your machine into safe mode with networking and see if it works correctly then.

  • IMa  Mac. HD    MY QUESTION:   LOST EVERYTHING ON COMPUTER.  HAVE USED DISK 1 AND 2 AND REINSTALLED.  IMAIL AND ICHAT WILL NOT SEND.

    IMac OS X, version 10.5.8; GHzIntel Core 2 Duo;  Memory of GB 800 MHz DDR2 SDRAM; MAC HD;
    MY QUESTION:   LOST EVERYTHING ON COMPUTER.  BACKUP DID NOT OR WAS NOT WORKING.  I HAVE REINSTALLED DISC 1 & 2 THAT CAME WITH THE COMPUTER.  IMAIL WILL NOT SEND OR RECEIVE NOR WILL ICHAT.   I HAVE USED APPLE SUPPORT FOR IMAC MAIL AND STILL NO PROGRESS.   ??????
    DOUGGEN

    Hmmm, their info may be out of date, but their site said SSL should be OFF & Port 110.
    Some notes on mail...
    Open Keychain Access in Utilities, use Keychain First Aid under the Keychain Menu item, then either check the Password under that item, change it, or delete it and start over.
    You may have multiple entries.
    Open Keychain Access in Utilities, enter the part after the @ sign in the search bar, hit enter
    The Password rejection can confuse people since it's a catch all meaning...
    This Password, Username, Authentication method... is not recognized on this Port to this Server, more than one entry in Keychain for each in/out entry, or a server end problem.
    If using a browser to login via WebMail works it's not Name or Password, but one of the other ones.
    The receiving email ports are:
    IMAP is port 143
    IMAP-SSL is port 993
    POP is port 110
    POP-SSL is port 995
    Outgoing ports are...
    SMTP and SMTP-SSL is on ports 25, 587 and 465. Port 587 has to be SSL, and port 465 is enforced TLS-wrapped and is generally used by Outlook users.

  • Since the upgrade my iphone periodically will not send iMessages to other iPhones. I am able to receive them and can send from my iPad. When I push send the bar goes 3/4 of the way and the stops and will not send at all

    Since the upgrade my phone will not send iMessage to other iPhones. I can send from my iPad. When I try and send the message sends 3/4 of the way and then stops and does not send at all

    SharmFarm wrote:
    Good ev Ning Mario49    firstly I would like to say a great thank you for your attention to trying to help me,,,,,    i have looked at the links and will try everything stated first thing…
    Hi Mario,,,,
    I tried everything in your reply,,, thank you again,, I had done that once before and all was working great,,
    I have just now tried the Reinstall via iTunes, about 20 into the download, the iTunes logo on the phone disappeared, and the Apple Logo appeared again,,, I waited until the iTunes stated that the download had finished, and the install was in progress,,,
    Nothing happened, still the Apple Logo was visual on the screen, iTunes never recognised the phone which it was on my iTunes account previously,,,
    Still just a bunch of lines, maybe 5 or 6 so small writing,, I personally can not read what it is telling me, someone said it reads, incorrect shutdown,,,????????
    Please advise,???
    I am now at a loss,,, I really became excited when I saw the iTunes icon after putting the phone into restore,,,???
    Thank you again
    D

  • After accepting the carrier update yesterday my iPhone 5s will not receive emails via my work Exchange system.

    After accepting the carrier update yesterday my iPhone 5s will not receive emails via my work Exchange system.  I can send emails, but can not receive.  I deleted my account and added it back with the directed provided by our Corporate IT, but I still can't receive emails.  I've hard booted and soft booted my phone several times to no avail.  What else can I do to help remedy this situation?

    I don't have any other email accounts on my phone and I don't get any type of error message.  It just says "Checking for Mail" and I receive nothing, so I know that it is accessing my work email system.  I haven't made any changes to my account.  I only accepted the message to update my carrier system.....I do have an appointment with the local Verizon store to see if they can help.
    Just FYI, my Exchange email account still works on my iPad, so I'm pretty sure the settings are correct.

Maybe you are looking for