SSH timeout not available while on ssh connection

Hi Everyone,
I found that ssh timeout command is  only available when you console to ASA.
It is not available when you do the ssh connection to ASA is this default behaviour? or any reason behind it?
Thanks
Mahesh

Hi Jennifer,
My bad actually i overlooked the command.
it does have  option
ciscoasa(config)# ssh                         ?
configure mode commands/options:
  Hostname or A.B.C.D  The IP address of the host and/or network authorized to
                       login to the system
  X:X:X:X::X/<0-128>   IPv6 address/prefix authorized to login to the system
  scopy                Secure Copy mode
  timeout              Configure ssh idle timeout ?????????????
  version              Specify protocol version to be supported
exec mode commands/options:
  disconnect  Specify SSH session id to be disconnected after this keyword
Thanks for help.
MAhesh

Similar Messages

  • HT4623 I am updating my school's operating system for my iPads.  I have been able to complete 2 carts of 30 (60 total). The next cart I was able to download the IOS6.3.1 update but it states the install is not available. Good internet connection.

    I am updating my school's operating system for my iPads.  I have been able to complete 2 carts of 30 (60 total). The next cart I was able to download the IOS6.3.1 update but it states the install is not available. Good internet connection.  Please advise.....
    Thanks!

    Hi nytesinger,
    Welcome to the Support Communities!
    The article below may be able to help you with this issue.
    Click on the link to see more details and screenshots. 
    Apple Configurator Help: About Apple Configurator
    http://help.apple.com/configurator/mac/1.3/#cadf1802aed
    Apple Configurator Help: Prepare devices
    http://help.apple.com/configurator/mac/1.3/#cad96c7acd6
    Cheers,
    - Judy

  • The scanner is not available while in use by another application?

    i have canon lide 100..whn i scan..its shows mgs the scaner is not available while use in another aplication..plz help me

    Hi carenson,
    To isolate the issue you describe, please follow these instructions to put your computer in a Selective Startup:
     1.  Press the Windows key on the keyboard and then press R.
     2.  In the Open box of the Run window, type msconfig and and then click OK.
     3.  In the General tab of the System Configuration Utility window, click on the Selective Startup radio button.
     4.  Remove the check in the Load Startup Items box.
     5.  Click the Services tab.
     6.  At the bottom of the Services tab, click Hide all Microsoft Services box.  The window will refresh.
     7.  Under Service column, uncheck each box that is left in this tab.
     8.  Click Apply and then Close.
     9.  Click Restart.
    10.  Proceed to use your scanner to see if the issue you described has been corrected.
    11.  After using your scanner, repeat steps 1 and 2, click Normal Startup and then restart your computer.
    Are you able to use the scanner while in selective startup?
    Did this answer your question? Please click the Accept as Solution button so that others may find the answer as well.

  • HT4060 My USB charger is not supporting while i am connecting from PC to iPad for charging (showing as " Not Charging"), Kindly advice me

    My USB charger is not supporting while i am connecting from PC to iPad for charging (showing as " Not Charging"), Kindly advice me

    Hi Folks,
    I have tried most of what have been said here ( thank you for the great Job) but unforunatally it didn't solve the issue.
    However, now the "Not Charging" message in the right corner disappeared and my iPad is charging normally from my laptop.
    The reason behind that is using the USB3.0 port in my Dell inspiron N5110. Earlier, I was using the USB 2.0  ports and that is why it was showing that message but as sooon as I pluged it in the eSATA USB 3.0 port , the message disapeared and the iPad started charging normally.
    So don't waste ur time here and there try to plug it to USB 3.0 port and it will works, Insha ALLAH.
    Cheers
    KoRn

  • ORACLE not available!problem in connecting the oracle-xe-10g.

    SQL> conn
    Enter user-name: chris
    Enter password:
    ERROR:
    ORA-01034: ORACLE not available
    ORA-27101: shared memory realm does not exist
    Linux Error: 2: No such file or directory
    SQL>

    Hi,
    I have the same problem during XE installation on Windows 2003 R2 SP 2 Enterprise edition. I have uninstall the oracle xxe and the result still the same. Finally I uninstall the windows and start all over again, surprisingly the result still the same. FYI, we normally has no issue during installation because this is part of our system we sell to our customer which require oracle xe. This is the first time we have seen this issue.
    ORA-01034 : Oracle Not available
    ORA-27101 : Shared memory realm doesn't exist.
    Oracle XE and listener services is started in the windows services.
    if we try to do startup the following message occured.
    SQL> connect /as sysdba
    Connected to an idle instance.
    SQL> startup
    ORA-44412: XE edition memory parameter invalid or not specified
    SQL>I can send you the oracle_xe log, init ora, and OpsBuildAll.log to create the database.
    When we compare with the working installation, we saw that the size of oraclexe folder is less, it's just 233MB while the working one is over 1GB. After investigation, found out that the .dbf files is not avaiable in the oradata folder, i have tried to copy those files from the working one but the problem stay the same, probably there are a lot of files more missing.
    Appreciate your help on this.
    Thanks,
    Agus

  • When I go to install OS X on the disk utility I got a prompt telling me that Mac 10.7 is not available. I am connected to the internet. What do I do in order to install OS?

    My laptop was running slow while in the regular mode, but in safe mode it would work fine. I deleted all of the content through the disk utility. Once I would go back to the recovery mode prompt and click on install os I go to the next page and get a prompt that says mac os x 10.7 is not available. There also is no picture to the left of the OS system like most people have on their recovery mode screen on the install option. Please help!
    Thanks!

    cernstes wrote:
    I was planning on buying one of those lens cleaners discs here soon and then see what happens.
    That might do.  There is the 'poor man's' alternative.  Take a fine microfiber cloth (eyeglasses cleaning cloth) and wrap it around a business card.  Insert it gently into the slot.  Some times it works.  Do not dismiss the possibility that the DVD drive is kaput.
    I did purchase this laptop from my brother a couple years ago. He told me the first operating system that was on the laptop was OS X 10.6. He gave me the disc to install,
    According to the information that I have, a Mid 2009 MBP came with Leopard (10.5).  You will have to install Leopard (if you have the original disk) or purchase from the online store a Snow Leopard (10.6.3) retail disk.
    http://store.apple.com/us/product/MC573Z/A/mac-os-x-106-snow-leopard
    This disk is a requisite in order to install and run Lion (10.7) or any other newer OSX.  You have to update Snow Leopard to 10.6.8 before downloading and installing Lion.
    Ciao.

  • System Type ERP not available while creating Buisness System For ECC in SAP Sourcing 9.0

    Hi,
    I need to import Master data in SAP Sourcing but when i am uploading master data i am getting this errror
    Business system ECQCLNT340 does not match with local SAP Sourcing System ID SOURCING.
    i have followed the steps in config guide of SAP ERP with SAP Sourcing.
    when i am creating business system in SAP Sourcing system type ERP is not available.
    i have also attached the error file, please check
    --------------Version---------------
    ECC 6.0 Ehp6
    SAP Sourcing 9.0 on NW7.3 Ehp1 on IBM DB2
    Thanks and Regards,
    Murtaza Najmi

    Thanks you Prasad,
    this issue has been resolved and i have completed the installation part of SAP Sourcing and Contract generation.
    Now , I am getting error while uploading clause document,  my functional team member are not able to upload clause document. kindly suggest.
    ----------------------Error Description---------------
    Login with buyer link into the system-> it has all authorizations
    then Goto -> Contract Management -> Clause Library -> Clause list -> Click on New button -> Click on Add button -> Browse Document
    it is showing POPUP with Error that "There is a problem with the Contract Generation web service Contact your system administrator"
    Thanks and Regards,
    Murtaza Najmi

  • I get the message 'You are not connected to the internet.  Online functionality is not available'  But I am connected to the Internet

    I get the message'You are not connected to the internet.  Online functionality is not available'  I am connected so what can I do?

    Try:
    - A reset. Nothing is lost
    Reset iPod touch: Hold down the On/Off button and the Home button at the same time for at
    least ten seconds, until the Apple logo appears.
    - Power off and then back on the router
    - Reset Network Settings: Settings>General>Reset>Reset Network Settings
    - iOS: Troubleshooting Wi-Fi networks and connections
    - iOS: Recommended settings for Wi-Fi routers and access points
    - DId the iPod ever successfully connect to the network?
    - Does the iPod successfully connect to other networks?
    - Do other devices successfully connect with your network?

  • Change connection timeout, not found waiting for dialup connection

    Using Firefox 6.02 on Vista 32.
    The dial-up connection is slow connecting which cause Firefox to time out with a page not found while waiting. Is there a setting to extend the time out?

    Mark,
    This has been implemented in Headstart PATCH6530_for_6i and PATCH6530_for_9i.
    Regards,
    Marcel

  • 0db* iobj are not available while installing 0sd_c03 update rules

    Hi all,
    i am facing this problem while installing the update rules of 0sd_c03.
    the following objects are could not be collected and they are not avialable in version d.
    all the objects are the nav attributes of 0sold_to
    they are 0sold_to_0dbareacod
    0sold_to_0dbctrycod
    0sold_to_0dbctrynam
    0sold_to_dbcustat
    0sold_to_0dbdistrcod
    0sold_to_0dbempbnd
    0sold_to_0dbhqduns
    0sold_to_0dblglgstat
    0sold_to_0dblocacod
    0sold_to_0dbregcod
    0sold_to_0dbsalnd
    0sold_to_0dbsectcod
    0sold_to_0dbmaktcod
    0sold_to_0db_mktcds
    How can i fix this issue?
    can anyone please throw a light on this one?
    Thanks & regards,
    V. Vijay

    hi,
    these objects are not available as a nav attr of 0sold_to ., while i am seeing in that iobj.
    it is showing only the 0dbduns_num only obj as a nav attr of sold_to. the remaining iobj are not showing..
    i have tried to install 0sold_to as a seperate also, but invain..
    these objects are not showing...
    any ideas..
    Regards,
    V. Vijay.

  • Service not Available while trying to update the D...

    Hi,
    I am trying to update the device software of my Nokia E5.
    In Ovi Suite it shows that 1 software update for the device is available.
    However, while trying to update the device it creates a backup and says "Service Not Available" -- Try Again Later. This is happening for quite a long time.
    Please help in this matter.
    Thanks.

    wezzyd wrote:
    might be the nokia servers down
    No issues 13.00hrs GMT 30/01/12
    Happy to have helped forum with a Support Ratio = 42.5

  • If "ORACLE not available" how to refresh connection pool

    Hi,
    Sometimes i'm getting this error "ORACLE not available" , but the connection pool was not refreshigng.
    so after the oracle connection comes, my program is using old connection in pool and not picking the data from the database, until i restart the tomcat server.
    can anyone give better solution rather than restarting the server.
    thanks in advance,
    regards,
    NeelimaSridhar

    i got the answer
    Have to specify the query �select 1 from dual� in validation query column.

  • Oracle not available while creating RAC database

    Hi,
    I have got 2node Oracle 10gR2 RAC installed on solaris 10 and am using NFS for keeping clusterware and database files.
    cluvfy with pre dbinst option ran successfully.
    Now while creating RAC database through DBCA, I am getting Oracle not Available error message. No relevant message written in alert log.
    Can you suggest me as to what to do to resolve the issue please.
    Thanks in advance.

    Do you see any kind of logs under $OH/cfgtool*/dbca/..may be it will help with some pointers. If that doesn't give any useful information, try to startup nomount the instance using a sample init.ora file to see if reports anything in the alert log.
    Thanks
    -Chandra

  • Partner profile not available while sending mail

    Hi Experts,
    I have used a customized program which is called by tcdoe va41, where once when i click on issue output to..
    I need to send email to the customer, but i get a message that Partner profile not available.
    Can any one help me in this issue

    hi
    you can create  the parnter profile using tcode WE20. hope it will help you .  
    ~linganna

  • Error 'Program not registered' while testing RFC connection PI_RFC

    Hi Basis Experts
    I am having problems while testing an RFC connection PI_RFC in one of our PI quality system.
    Here is the Error log
    Logon Connection Error
    Error when opening an RFC connection
    ERROR: program PI_RFC not registered
    LOCATION: SAP-Gateway on host bp1xeuaa202 / sapgw01
    DETAIL: TP PI_RFC not registered
    Details COMPONENT: SAP-Gateway
    COUNTER: 15866
    MODULE: gwr3cpic.c
    Details RETURN CODE: 679
    We tried restarting the JCO-RFC provider service in VA,also tried restarting the Gateway service, tried registering the RFC using below command
    rfcexec u2013g PI_RFC -a bp1xeuaa202 -x sapgw01
    rfcexec u2013D PI_RFC
    the command didnt gave any output also in SMGW tcode we didnt get the entry(PI_RFC) under system type as registered server.
    Also we tried changing the Gateway hostname and service name in SM59.
    Still we are facing the same issue, can anyone please help us in resolving this issue.
    Regards
    Syed

    Hi,
    It seems to like problem with your program is not registered.  As suggested by spantaleoni, you can go through.
    Here Program Id  must be case sensitive.  Once again check with your program Id.
    And, you have to register your program id in Visual Administrator.
    Goto  Visual Administrator:
    In that Select Cluster>Server>Services-->JCo RFC Provider
    Then enter the Program Id and gw host & service.
    Hope this helps to you.
    Regards,
    P.Rajesh

Maybe you are looking for

  • Use of planning file entries

    hi pp gurus can any one explain me what is the use of planning file entries one moree problem when i converting existing planning file entries into new file entries. system gives the resullt converted planning file entries-0 so why it is happening re

  • What cable to use for this?

    I am trying to hook up my xbox 360 to my Macbook pro, and I am unsure of what cable to use for this. Composite cables.

  • Creating a pdf link instead of html

    i want to ensure i have a pdf of web pages i wrote rather than just a link to the existing website -- that way, when/if the website goes down, there is still record of my work -- how do you create this?

  • Issue  with programmatic clipboard access in IE7

    I have a J2EE application. The application is an intranet application. We have an ActiveX component (Far point Spread control) in the web page to display the data. We had recently upgraded the IE from 6 to 7 version. After that, we are not able to co

  • CM Repository using content server.

    Hi Experts,           I am currently setting up KM in SAP EP 7.0. I have installed both Trex 7.1 and Content Server 6.40. Would like to check with you guys on how to create a CM repository that points to content server 6.40? Thanks.