Still having problems with my hpC3180 - printing "gobbeldy"
can anyone explain why my printer is printing all kinds of weird stuff when I print from the internet?
when I preview before printing everything looks OK but when I print i get lots of things like $3!sf e and dvul27
Put the device in DFU mode (google it) and restore as new.
Similar Messages
-
I had already update mi new factory unlocked iPhone 4S to iOS 5.1.1 and I still having problems with "invalid sim". I'm from Argentina and here we don't have official service. PLEASE HELP ME, WHAT CAN I DO??? In Argentina is too expensive an iPhone 4S. Please I need help to continue believing in Apple. Thanks a lot. If anybody speak spanish better.
Was it purchased from an official Apple Store, not a reseller? Only Apple Stores sell official factory unlocked phones. The others sell hacked to unlock phones, and the unlocking is unstable.
Try these steps, as needed:
1. Reset phone - press both home and on/off buttons for at least 10 seconds until the Apple logo appears.
2. Settings > General > Reset > Reset Network Settings.
3. Replace SIM card (and reset network settings again)
4. Restore Phone in iTunes using a backup
5. Restore in iTunes as new, without using a backup -
I'm frustrated, I am doing everything you recommend, I use only two channels, have plenty of memory in my hard disk, and external hard drive, no effects, and still having problems with Garage band. Giving messages as you ave too many live channels, the disk is slow prepare...can you help?
Quote from: Richard on 15-November-07, 20:33:05
tornado2003,
What you need to do is boot into Safe Mode. Then delete the VGA Drivers.
After that boot normally and install the latest nVidia ForceWare Drivers
Take Care,
Richard
i guess you missed that:
Quote from: tornado2003 on 15-November-07, 17:26:52
ive tryed booting xp in safe mode but it just freezes after it loads up a couple of needed files .
ive even formatted my hard drive and tryed installing a fresh xp on it but it just keeps locking up when it gets to the "starting windows setup" .(this is just after it loads all the drivers from the xp cd) -
I am still having problems with my music videos freezing (all purchased on iTunes) since the update. The first day of the update, no problems...played 6 hours of music videos and no freezing. Today...every single video froze!!! So frustrating! I rebooted, restarted, powered down and no help. I would appreciate any suggestions. Thanks.
I don't know how to do this without using a mouse point.
This may help, http://www.computerhope.com/issues/ch000542.htm
As for question #2, you call tell how iTunes is sorting songs by the up or down arrow next to a header name.
Even the original order that the songs were entered or date added or last played can be sorted.
Much easier with a mouse or touch pad. -
Still having problems with my security questions as they were not the ones I answered and now I'm confused.
Howdy Paul,
If you are having an issue with your Apple ID security questions, you can reset them using the steps in this article -
If you forgot the answers to your Apple ID security questions - Apple Support
Thanks for using Apple Support Communities.
Best,
Brett L -
Still having problems with wireless connections with the new lions os
is anyone else still having problems with there wireless connections on the new lions os? What a poor job apple did
No.
-
Still having ******* problems with downloading apps
Still having ******* problems with downloading apps
I know. Alot of people think that 1.1.2 solved it. Looks like it didn't.
lenn -
Hi everyone ive put up a few posts as regards to my iphone, im still currently having problems with windows recognizing it the usb cord an the itunes logo appears on the phone along with the message on my computer USB Device not Recognized, One of the USB Devices attached to this computer has malfunctioned an Windows does not recognize it "Unknown Device Properties comes up an in the genral properties Device Status box says no drivers are currently installed for this device please help
Put the device in DFU mode (google it) and restore as new.
-
Still having Problems with yamaha USB UX16 midi device can anyone help??
I have setup drivers on my computer which have installed successfully. In logic I have setup environment so Physical input sequenser and keyboard are all connected up in Click and Ports layer.
When I am trying to play keyboard I still have no input or outport signal in transport window I am stuck on what to do??
please can someone help???I take back all I said. After reading reviews of this product, take it back to wherever you bought it and buy something else, anything else, everyone hates this thing, and is having problems with it. get a midisport instead.
http://www.midiman.com/index.php?do=products.list&ID=usbmidiinterfaces
here are a couple of reviews:
Dec 12, 2006 - It is hit or miss as far as compatability goes and you don't know until it is too late if the full instruction set is going to be sent/recieved intact. Tried it on various Macs, PCs and inconsistent in every situation. Yamaha needs to issue a full recall on this POC called the UX-16.
Nov 6, 2004 - The first Yamaha UX 16 that I bought worked okay for a day, then started to cause a buzzing noise. The next day, it was not recognized at all by my laptop. I returned it to the retailer, hoping to find a competitive portable USB/MIDI interface at another store. After failing to find an alternative at the other store, I bought the Yamaha UX16 again, hoping that the first dud was a fluke.
The second UX16 also worked for one day before giving out.
Avoid the UX16.
Apr 12, 2004 - This thing only works for a short period of time then quits being detectable to windows for random periods of time. Totally unreliable. -
Still having problems with images
I am still having problems putting images into an Oracle 9i database and fetching them back out.
I think I have finally managed to force a blob image into the database, but can't seem to get it back out into a byte array.
After many iterations, I have come up with something that might be getting close.
The code is listed below.
Everything has been simplified as much as I can.
The function get_user_picture_func1 returns a single blob for a specified index.
In this case, I have hardcoded the index = 3 and I think there is an image in the database for that index. (it says there are bytes there anyway).
The byte array to store the image is defined outside the method fetchImage().
byte[] imageData;
When I call fetchImage() I get the following exception:
Invalid argument(s) in call: getBytes().
at the line
imageData = picture.getBytes(zro, k);
It looks like getBytes has two parameters, Long offset, int length.
I had diagnostic statements and I confirmed that the statement:
int k = (int)picture.length(); returned k=4198 (the same size as the image).
I am at a loss to understand what the exception is trying to tell me.
I'be been trying to get this to work for a week now and am really getting burned out trying to find anything that works.
void fetchImage()
Blob picture;
String query = "{ ? = call get_user_picture_func1( ? ) }";
try
CallableStatement cs = con.prepareCall( query );
cs.registerOutParameter(1, OracleTypes.BLOB);
cs.setInt(2,3);
cs.execute();
picture = cs.getBlob(1);
if( picture != null)
InputStream in = picture.getBinaryStream();
int k = (int)picture.length();
imageData = new byte[k];
long zro = 0;
imageData = picture.getBytes(zro, k);
catch( Exception e)
}I have been using my iPad mini with keynote to make slide presentations in my classes.There has been no problem until I upgraded to Keynote 5.3. Now the refresh rate on the iPad mini is so slow and out of sync with the projected image that I was forced to not use keynote! I have 2 years of work invested that I will have to toss unless this gets fxed. I have not had this problem with this equipment/files before. Only change was upgrade to keynote 5.3. ( Some details: I connect to the projector with a VGA cable and Apple lightining adaptor to the iPad Mini. All updates current on theiPad Mini.) Yes I did turn on and off all equipment. And I did check all cable connections. Thanks for any help you may give!
-
Still having problems with VPN access
Hello!
I am having problems with my VPN clients getting access to the networks over a MPLS infrastruture. I can reach these resources form my Core network (172.17.1.0/24) and my Wifi (172.17.100.0/24) but not from my VPN network (172.17.200.0/24). From the VPN I can reach the Wifi network (which is behind a router) and the rule that allows that also allows access to the other networks but for some reason it is not working.
When I ping inside the core network from VPN I can connect and get responses. When I ping to the Wifi network, I can get responses and connect to resources there. A tracert to the wifi network shows it hitting the core switch (a 3750 stack) @ 172.17.1.1, then the Wifi router (172.17.1.3) and then the host. A tracert to a resource on the MPLS network from the VPN shows a single entry (the destination host) and then 29 time outs but will not ping that resource nor connect.
I've posted all the info I can think of below. Any help appreciated.
*** Here is a tracert from a core network machine to the resource we need on the MPLS:
C:\Windows\system32>tracert 10.2.0.125
Tracing route to **************** [10.2.0.125]
over a maximum of 30 hops:
1 1 ms <1 ms <1 ms 172.17.1.1
2 1 ms <1 ms <1 ms 172.17.1.10
3 5 ms 5 ms 5 ms 192.168.0.13
4 31 ms 30 ms 31 ms 192.168.0.5
5 29 ms 30 ms 29 ms 192.168.0.6
6 29 ms 29 ms 29 ms 192.168.20.4
7 29 ms 29 ms 29 ms RV-TPA-CRMPROD [10.2.0.125]
Trace complete.
172.17.1.10 is the mpls router.
**** Here is the routing table (sh ip route) from the 3750 @ 172.17.1.1
Gateway of last resort is 172.17.1.2 to network 0.0.0.0
S 192.168.30.0/24 [1/0] via 172.17.1.10
172.17.0.0/24 is subnetted, 3 subnets
S 172.17.200.0 [1/0] via 172.17.1.2
C 172.17.1.0 is directly connected, Vlan20
S 172.17.100.0 [1/0] via 172.17.1.3
172.18.0.0/24 is subnetted, 1 subnets
S 172.18.1.0 [1/0] via 172.17.1.10
S 192.168.11.0/24 [1/0] via 172.17.1.10
10.0.0.0/8 is variably subnetted, 4 subnets, 2 masks
S 10.2.0.0/24 [1/0] via 172.17.1.10
S 10.10.10.0/24 [1/0] via 172.17.1.10
S 10.20.0.0/24 [1/0] via 172.17.1.10
S 10.3.0.128/25 [1/0] via 172.17.1.10
S 192.168.1.0/24 [1/0] via 172.17.1.10
S* 0.0.0.0/0 [1/0] via 172.17.1.2
*** Here is the firewall config (5510):
ASA Version 8.4(1)
hostname RVGW
domain-name ************
enable password b5aqRk/6.KRmypWW encrypted
passwd 1ems91jznlfZHhfU encrypted
names
interface Ethernet0/0
nameif Outside
security-level 10
ip address 5.29.79.10 255.255.255.248
interface Ethernet0/1
nameif Inside
security-level 100
ip address 172.17.1.2 255.255.255.0
interface Ethernet0/2
shutdown
no nameif
no security-level
no ip address
interface Ethernet0/3
shutdown
no nameif
no security-level
no ip address
interface Management0/0
nameif management
security-level 100
ip address 172.19.1.1 255.255.255.0
management-only
banner login RedV GW
ftp mode passive
dns server-group DefaultDNS
domain-name RedVector.com
same-security-traffic permit inter-interface
same-security-traffic permit intra-interface
object network WiFi
subnet 172.17.100.0 255.255.255.0
description WiFi
object network inside-net
subnet 172.17.1.0 255.255.255.0
object network NOSPAM
host 172.17.1.60
object network BH2
host 172.17.1.60
object network EX2
host 172.17.1.61
description Internal Exchange / Outbound SMTP
object network Mail2
host 5.29.79.11
description Ext EX2
object network NETWORK_OBJ_172.17.1.240_28
subnet 172.17.1.240 255.255.255.240
object network NETWORK_OBJ_172.17.200.0_24
subnet 172.17.200.0 255.255.255.0
object network VPN-CLIENT
subnet 172.17.200.0 255.255.255.0
object-group service DM_INLINE_TCP_1 tcp
port-object eq www
port-object eq https
object-group network DM_INLINE_NETWORK_1
network-object object BH2
network-object object NOSPAM
object-group network VPN-CLIENT-PAT-SOURCE
description VPN-CLIENT-PAT-SOURCE
network-object object VPN-CLIENT
object-group network LAN-NETWORKS
network-object 10.10.10.0 255.255.255.0
network-object 10.2.0.0 255.255.255.0
network-object 10.3.0.0 255.255.255.0
network-object 172.17.100.0 255.255.255.0
network-object 172.18.1.0 255.255.255.0
network-object 192.168.1.0 255.255.255.0
network-object 192.168.11.0 255.255.255.0
network-object 192.168.30.0 255.255.255.0
object-group network VPN-POOL
network-object 172.17.200.0 255.255.255.0
object-group protocol DM_INLINE_PROTOCOL_1
protocol-object ip
protocol-object icmp
access-list Outside_access_in extended permit tcp any object-group DM_INLINE_NETWORK_1 eq smtp
access-list Outside_access_in extended permit tcp any object BH2 object-group DM_INLINE_TCP_1
access-list global_mpc extended permit ip any any
access-list Inside_access_in extended permit object-group DM_INLINE_PROTOCOL_1 any any
pager lines 24
logging enable
logging asdm informational
no logging message 106015
no logging message 313001
no logging message 313008
no logging message 106023
no logging message 710003
no logging message 106100
no logging message 302015
no logging message 302014
no logging message 302013
no logging message 302018
no logging message 302017
no logging message 302016
no logging message 302021
no logging message 302020
flow-export destination Inside 172.17.1.52 9996
mtu Outside 1500
mtu Inside 1500
mtu management 1500
ip local pool VPN 172.17.1.240-172.17.1.250 mask 255.255.255.0
ip local pool VPN2 172.17.200.100-172.17.200.200 mask 255.255.255.0
no failover
icmp unreachable rate-limit 1 burst-size 1
no asdm history enable
arp timeout 14400
nat (Inside,Outside) source static EX2 Mail2
nat (Inside,Outside) source static any any destination static NETWORK_OBJ_172.17.1.240_28 NETWORK_OBJ_172.17.1.240_28
nat (Inside,Outside) source static any any destination static NETWORK_OBJ_172.17.200.0_24 NETWORK_OBJ_172.17.200.0_24
nat (Inside,Outside) source static inside-net inside-net destination static NETWORK_OBJ_172.17.1.240_28 NETWORK_OBJ_172.17.1.240_28
nat (Inside,Outside) source static LAN-NETWORKS LAN-NETWORKS destination static VPN-POOL VPN-POOL
object network inside-net
nat (Inside,Outside) dynamic interface
object network NOSPAM
nat (Inside,Outside) static 5.29.79.12
nat (Outside,Outside) after-auto source dynamic VPN-CLIENT-PAT-SOURCE interface
access-group Outside_access_in in interface Outside
access-group Inside_access_in in interface Inside
route Outside 0.0.0.0 0.0.0.0 5.29.79.9 1
route Inside 10.2.0.0 255.255.255.0 172.17.1.1 1
route Inside 10.3.0.0 255.255.255.128 172.17.1.1 1
route Inside 10.10.10.0 255.255.255.0 172.17.1.1 1
route Inside 172.17.100.0 255.255.255.0 172.17.1.3 1
route Inside 172.18.1.0 255.255.255.0 172.17.1.1 1
route Inside 192.168.1.0 255.255.255.0 172.17.1.1 1
route Inside 192.168.11.0 255.255.255.0 172.17.1.1 1
route Inside 192.168.30.0 255.255.255.0 172.17.1.1 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-record DfltAccessPolicy
aaa-server RedVec protocol ldap
aaa-server RedVec (Inside) host 172.17.1.41
ldap-base-dn DC=adrs1,DC=net
ldap-group-base-dn DC=adrs,DC=net
ldap-scope subtree
ldap-naming-attribute sAMAccountName
ldap-login-password *****
ldap-login-dn CN=Hanna\, Roger,OU=Humans,OU=WPLAdministrator,DC=adrs1,DC=net
server-type microsoft
aaa authentication ssh console LOCAL
http server enable
http 192.168.1.0 255.255.255.0 management
http 172.17.1.0 255.255.255.0 Inside
http 24.32.208.223 255.255.255.255 Outside
snmp-server host Inside 172.17.1.52 community *****
snmp-server location Server Room 3010
snmp-server contact Roger Hanna
snmp-server community *****
snmp-server enable traps snmp authentication linkup linkdown coldstart warmstart
crypto ipsec ikev1 transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
crypto map Outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map Outside_map interface Outside
crypto ikev1 enable Outside
crypto ikev1 policy 10
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 30
authentication crack
encryption 3des
hash sha
group 2
lifetime 86400
telnet 172.17.1.0 255.255.255.0 Inside
telnet timeout 5
ssh 172.17.1.0 255.255.255.0 Inside
ssh timeout 5
console timeout 0
dhcpd address 172.17.1.100-172.17.1.200 Inside
dhcpd dns 172.17.1.41 172.17.1.42 interface Inside
dhcpd lease 100000 interface Inside
dhcpd domain adrs1.net interface Inside
threat-detection basic-threat
threat-detection statistics
threat-detection statistics tcp-intercept rate-interval 30 burst-rate 400 average-rate 200
webvpn
group-policy RedV internal
group-policy RedV attributes
wins-server value 172.17.1.41
dns-server value 172.17.1.41 172.17.1.42
vpn-tunnel-protocol ikev1
default-domain value ADRS1.NET
group-policy RedV_1 internal
group-policy RedV_1 attributes
wins-server value 172.17.1.41
dns-server value 172.17.1.41 172.17.1.42
vpn-tunnel-protocol ikev1
split-tunnel-policy tunnelspecified
default-domain value adrs1.net
username rparker password FnbvAdOZxk4r40E5 encrypted privilege 15
username rparker attributes
vpn-group-policy RedV
username mhale password 2reWKpsLC5em3o1P encrypted privilege 0
username mhale attributes
vpn-group-policy RedV
username dcoletto password g53yRiEqpcYkSyYS encrypted privilege 0
username dcoletto attributes
vpn-group-policy RedV
username rhanna password Pd3E3vqnGmV84Ds2 encrypted privilege 15
username rhanna attributes
vpn-group-policy RedV
tunnel-group RedV type remote-access
tunnel-group RedV general-attributes
address-pool VPN2
authentication-server-group RedVec
default-group-policy RedV
tunnel-group RedV ipsec-attributes
ikev1 pre-shared-key *****
class-map global-class
match access-list global_mpc
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect ip-options
inspect icmp
class global-class
flow-export event-type all destination 172.17.1.52
service-policy global_policy global
prompt hostname context
call-home
profile CiscoTAC-1
no active
destination address http https://tools.cisco.com/its/service/oddce/services/DDCEService
destination address email [email protected]
destination transport-method http
subscribe-to-alert-group diagnostic
subscribe-to-alert-group environment
subscribe-to-alert-group inventory periodic monthly
subscribe-to-alert-group configuration periodic monthly
subscribe-to-alert-group telemetry periodic daily
hpm topN enable
Cryptochecksum:202ad58ba009fb24cbd119ed6d7237a9Hi Roger,
I bet you already checked it, but does the MPLS end router has route to VPN client subnet 172.17.200.x (or default) pointing to core rtr)?
Also, if the MPLS link has any /30 subnet assigned, you may need to include that as well in Object group LAN-NETWORKS.
Thx
MS -
I'm still having problems with XUL Runner - please help am getting desperate!
I recently sought help over a problem I am having with FF. When I try and load it, I get a message telling me that XUL runner 1.9.2.11 is not compatible with 1.9.2.12. The advice I received was to do a clean install. I have done this a number of times - using the Uninstall option in Control Panel as well as running the uninstall utility in the Firefox program folder. Each time I reinstall, and get the same problem. The only difference is that a few days ago I was installing FF 3.6.10, and that gave the error message that XUL runner 1.9.2.11 was not compatible with 1.9.2.10.
I have FF set as my default browser, so when I click on links in e-mails, etc. I get the same failure to load symptoms. However, I found by chance that FF works OK in conjunction with System Mechanic 10 - a maintenance utility I have on my machine. If I select the on-line help option from that Menu, FF loads and runs OK. I can open new tabs and have no problem loading other pages. However, even with FF open, if I click a link in an e-mail, I get the XUL Runner error message.
Although not all symptoms are the same, I am also having problems with IE8. When I run the program it loads, shows a 'connecting' message in the tab header, then closes. If I uninstall FF, then System Mechanic selects IE8 as the default browser, and as with FF, loads OK.
Chrome and Safari both run OK (thankfully). there must be someone out there who knows what this all points to - is that person you?!
Note: Trouble shooting information retrieved using FF when opened with System Mechanic.If you have such problems then you need remove the Firefox program folder before installing a new copy of the full Firefox installer.
It is important to delete the Firefox program folder to remove all the files and make sure that there are no problems with files that were leftover after uninstalling. -
Having problem with wi-fi printing
I had a Macbook Pro running 10.6.8, a Time Capsule (TC), and an HP 6980 printer connected via the TC so I could print wirelessly from the laptop.
In June, I replaced the Macbook Pro with a newer Macbook Pro running Mavericks (10.9.2). I was still able to print to the printer without any problems. In July, I had to replace the TC and by then the laptop had been upgraded to 10.9.4. I was able to setup the printing through the TC the same as I did before. I was able to print. I'm still able to print... sort of...
The problem I'm having is that after I print something (or several somethings if all of them enter the queue while the first thing is still printing), the laptop can no longer print through the TC unless I power cycle the printer (the printer queue says "looking for printer"). Essentially, it seems that as soon as the printer goes "idle" the OS can no longer see it unless I power cycle the printer. It's gotten annoying. If I go into "Printers and Scanners" in the System Preferences app, and select "Open Print Utility", it opens up the HP print utility, finds the printer, and displays information about it including ink level. But the print queue still says "looking for printer". I don't know if the problem is with the OS, the TC or the printer and I don't know how to figure it out for certain but the way it looks to me is that the problem is in the OS since the HP printer utility sees the printer. I've contacted HP but since the printer is old, they won't help. I'm trying to avoid having to buy a new printer because after buying a new laptop and TC, I'm broke. :-)
Some more information: the TC has the IP address of 10.0.1.2, the printer has an IP address of 10.0.1.3 so I know they are on the same subnet, but I have no idea what IP address/subnet the laptop is on. I don't see anything in the preferences to let me see or set that. It's possible that routing is somehow not working correctly.
Also, if I go into the system information panel and select "printer" under the "hardware" heading, it lists the printer but says it's "offline".
Can anyone tell me what is going on and help me fix this?
Thanks.How is the printer connected to the TC?? Is it plugged in by ethernet or is it wirelessly connected or bottom of lowest.. Plugged in by USB?
http://h10032.www1.hp.com/ctg/Manual/c00591192.pdf
From the date in the manual this is a very old printer. And old stuff and new macs OS.. are often not a great combo.
I think a lot of the issue if you are using wireless is the networking of Mavericks.. which IMHO can be compared unfavourably to tin cans with wet string.
Did you start over on the print drivers.. ??
I would delete all printers in your computer. Download the latest drivers from HP and install them.
I would also factory reset the TC.
Which model is it and running what firmware?? 7.7.3 in the newest TC you are stuck.. if you have an older TC.. gen4 or earlier you might find earlier firmware, 7.6.1 superior to 7.6.4 .. I sure do.
Please try the following.
1. Factory reset.
The Factory Reset universal
Unplug your TC/AE. Hold in reset. and power the TC/AE back on.. all without releasing reset and keep holding in for about 10sec. The time is not important.. it is the front LED rapid flashing that indicates you are in factory mode.
Release reset.
If it doesn’t flash rapidly you have released reset at some point and try again.
Be Gentle! Feel the switch click on. It has a positive feel.. add no more pressure after that.
TC/AE will reboot after a couple of minutes with default factory settings and will wipe out previous configurations.
No files are deleted on the hard disk.. No reset of the TC deletes files.. to do that you use erase from the airport utility.
2. Set IPv6 to link local only in your computer.. this is crucial.
3. Use all short names in the TC.. so base station name.. try TCgenx (I replace the x with the actual gen).
Wireless name. TCwifi
You don't need to do this if you already have compliant names.. but please do not use names like
Fred Blog's Airport Time Capsule (it is wrong on many levels).
Mavericks took a new step in the direction of windows by changing to SMB protocol default. This causes unending issues.
4. Reinstall the printer to the newly renamed wireless or ethernet setup..
Always use ethernet if it is available.. it stands head and shoulders above everything else.
Wireless is second best.. USB is worst.
5. Test and see if you have got anywhere. If not directly plug the printer into the laptop by USB and ignore the problem!! When you have some money buy a new printer. -
Still Having Problems With Applets!!!!
First i'd like to thank all who responded to my last post regarding a downloadable copy of the J2SE API Documentation. I have downloaded it and am quite content.
I am still, however having a problem with my applets (all applets at that). Like i said before. I can view any applets i want through the command prompt using appletviewer. My problem is residing in execution directly through Microsoft Internet Explorer 5.x.
When i open the .html file containing my applet, the file loads in the browser but the applet does nothing. When i mouseover the applet a message is displayed in the browser's status bar stating "loading class. classname: class not found".
I have tried every applet i can get my hands on including downloaded applets from applet resource sites (even the example applets that came with the JDK1.4 when i downloaded it). They all react the same way, but will execute fine with the direct command prompt reference to appletviewer.
It's getting very irritating. I have tries everything including setting the classpath in the command prompt. I'm loosing hope of a solution so if anyone might have an idea of what i need to do to fix my problem, or anything i am doing wrong or haven't done, please give me a hint or help.
I am loving the java language and wish to further my knowledge and farmiliarity with it but i need to make sure everything works.
Sorry for rambling and i thank whoever offers a reply in advance.
ChanceH1. Check the codebase parameter in the html file that calls the applet
for example if you have an applet named MyApplet.class inside a directory applets and your html file outside that directory you should have a codebase like this "applets/".
<applet CODE="MyApplet.class" codebase="applets/" WIDTH=640
HEIGHT=480 ALIGN= center>
</applet>
2. Be sure that your IE support java check the properties and enable the JVM.
3. If your JVM version does not support Java 2, applets build on Java 2 will not work. -
Still Having Problem with Battery Overheating with Car Dock/Charger when using Maps/Navigation
I'm having a problem with the battery overheating when using Google Navigation in the OEM Samsung car dock and car charger. On a trip last weekend, I started off with a fully charged battery (because posts on other sites have complained that the Charge cannot keep up with the power draw of the Google nav app while using the car charger). About an hour into my trip, I got a message that the battery was overheating and to unplug the charger which I did. I then had to contend with the screen going out because it was running on the battery. I let the phone discharge to about 70% then tried the car charger again. Within a few minutes, I got the same overheating message. It was not an overly hot day and the car A/C was set at 68 degrees.
This morning (with the battery at about 85%) I tried to use the Navigation without the car dock while charging and got the same results...the phone battery overheated and I had to unplug the charger. The battery temperature reached 116 degrees. (also, the battery level was also dropping while using the Maps or Nav application even though it was hooked up to the car charger).
I'm very disappointed with this situation since I was hoping I could replace my old Garmin GPS with the Charge. But between the phone dimming the screen while running on battery, and having a depleted battery in the phone at the end of the trip, its just not a viable option. I really like this phone, but I'm running against the "return" clock.
Any ideas?
Could this be a software problem that will be corrected by an update in the future?
fyi: other Charge problems in the last 5 days:
- dropping audio on calls to other Verizon phones.
- use of camera flash causing the phone to reboot.
(I do have the 'class 4' 32gb card in my Charge)
Thanks in advance,
RichJerry:
Yes, the phone is charging while in the car dock. I confirmed it both under the "about phone-status-battery status" menu and by my battery widget. By watching the battery widget, I also noticed that the voltage steadily increased over the ride home. It started at about 3.90 volts and ended at 4.02 volts. I don't know if that is significant. This time the battery did not overheat. The Max temp was 110 degrees, but no notice to disconnect came up. This might be because the sun was behind me on the drive home rather than beating down on the dash like it was this weeked.
I've ordered a cheap universal dock from Amazon for about $15.00 which clips onto the a/c vent. I want to see if this keeps the temperature down. If this works, I can still return the fancy-schmantzy Samsung OEM car dock. (The car-dock interface wasn't that impressive anyway).
Please let me know if the volt change means anything.
And thanks again for your help!
Rich
Maybe you are looking for
-
Smart List not updating on iPod (Classic)
I've got an iPod Classic with my entire iTunes library syncing to it. I'm running iTunes 11.0.1.12 on Windows 7. I have a Smart Playlist that I have been using for several years, and until recently, when I sync the playlist to the iPod, it updates wh
-
use a MyBook for Mac external hard drive. I need space on garageband or the entire hard drive, since I am getting the "need space on the hard drive" messages. It's scary to move my precious music files! How should I move them to the external and feel
-
I recently bought a refurbished Mac Pro (4,1) 2.93ghz Quad core and I'm trying to get 2 monitors working with it like I had with my G5. The problem is that I cannot get either monitor to work with the Minidisplay port. I've tried using a MDP to VGA a
-
Hi All, Does OSB's business service supports dynamic JCA connection JNDI using ws-addressing. I mean, dynamically i am going to get JNDI value, which i need to pass it using ws-addressing in connecting to back-end. Something like dynamic partner link
-
Firefox 5.0.1 hangs with mac os x 10.6.8
Ever since the lastest update to firefox 5 (and 6) for mac, I'm finding that FF is often hanging when scrolling or typing. I have tried booting into safe mode and I have tried disabling all my add-0ns but it is still hanging. My other browsers are no