STP Configuration for SG300/SF300

I have configured RSTP on a set of switches I managed and just want to confirm I have done this correctly.
These switches are used within a business centre all in L2 mode with around 30 VLANs to keep each suites traffic seperate along with VoIP and wireless seperated. Each switch has RSTP enabled, the trunk link ports for data-sw2/voice-sw1/voice-sw2/voice-sw3 have been set to a cost of 64 all other ports have a cost of 128. The data-sw1 STP priority is set to 4096 with all other switches set to 8192.
Main reason I have enabled RSTP is due to a couple of occasions when a cable has been connected from one of the data ports to the voice ports such as data-sw2 to voice-sw1 which has caused the root port to change from the trunk port.
Does this look to be the correct configuration to always keep the trunk ports indicated in the diagram above set to forwarding?
Thanks.

Colin
Setting the STP priority on the root switch should work fine. When you say -
Main reason I have enabled RSTP is due to a couple of occasions when a cable has been connected from one of the data ports to the voice ports such as data-sw2 to voice-sw1 which has caused the root port to change from the trunk port
i'm assuming that this type of thing happened before you set the port costs and the STP priorities ?
If so i'm not sure how that happended. Assuming with no extra configuration data-sw1 had the lowest priority then it would be elected as the root bridge. So all uplinks to data-sw1 from the other switches would be the root ports. If you then connected a cable between the data-sw2 and voice-sw1 switches that should not have changed the root port ie.
data-sw2 now receives BPDU's direct from data-sw1. It also receives BPDUs from voice-sw1 but the cost of those BPDUs would be worse as they have gone through an extra switch so the root port should not have changed. Actually what should have happened is one of the ports on the connection between data-sw2 and voice-sw1 should have been blocked as connecting that cable would cause a loop and the other port would be the designated port.
So it's not clear, to me at least, how connecting that cable changed the root ports on either data-sw2 or voice-sw1.
Jon

Similar Messages

Snmp configuration for SG300

Hi,
Am trying to configure SNMP functionality for the first time on an SG300-28 switch so I can use mrtg to monitor it. I've defined no users, 2 groups (mrtg and mrtg2 for SNMPv1 and SNMPv2 respectively), both with No authentication required. Default View of Read. I also defined a Basic Community type and called it sg300, with the View Name of Default. Under Views I changed nothing; the Default has 1 Object ID subtree included.
The mrtg CFGMaker in cannot retrieve any information from the switch. I've used it before with routers, Windows servers, etc. with no problem so I have to be overlooking something specific to this switch.
Much appreciated.
--Ben

Agreed Jonathan was correct, that was the part I missed the first time through. I walked through again to make sure there wasn't anything else and have attached the notes I took, mostly so I'll have them next time I have to do it :)
Steps to configure SNMP for MRTG on SG200-26
***Note*** These are minimum steps only for a lab environment additional security settings may be required for production use.
Switch is starting at factory reset configuration state
Login to the switch
Default ip 192.168.1.254
Username: cisco
Password: cisco
Change Password
Expand SNMP Section on bottom of left navigation
Highlight communities on the expanded SNMP section
Click the Add button
Enter the IP address of the system that will be making SNMP requests to your switch
Community string: mrtg (or whatever you want to use)
Ensure Read Only is selected for your access mode
Click Apply
Click Close
Expand the Security Section on the left navigation bar
Highlight TCP/UDP Services
Click the Checkbox to enable SNMP Service at the top of the screen
Click Apply
In the top right hand corner you should see a flashing save button, make sure to save your config if your happy with it.
“Snmpwalk –c mrtg 192.168.1.254” Should now run and return
***Note*** If your looking for port numbers in the output they start with .49 for port 1 and go to .74 for port 26.
IF-MIB::ifHCOutOctets.49 = Counter64: 0
IF-MIB::ifHCOutOctets.50 = Counter64: 0
IF-MIB::ifHCOutOctets.51 = Counter64: 0
IF-MIB::ifHCOutOctets.52 = Counter64: 0
IF-MIB::ifHCOutOctets.53 = Counter64: 0
IF-MIB::ifHCOutOctets.54 = Counter64: 0
IF-MIB::ifHCOutOctets.55 = Counter64: 0
IF-MIB::ifHCOutOctets.56 = Counter64: 0
IF-MIB::ifHCOutOctets.57 = Counter64: 0
IF-MIB::ifHCOutOctets.58 = Counter64: 0
IF-MIB::ifHCOutOctets.59 = Counter64: 2849723
IF-MIB::ifHCOutOctets.60 = Counter64: 0
IF-MIB::ifHCOutOctets.61 = Counter64: 0
IF-MIB::ifHCOutOctets.62 = Counter64: 0
IF-MIB::ifHCOutOctets.63 = Counter64: 0
IF-MIB::ifHCOutOctets.64 = Counter64: 0
IF-MIB::ifHCOutOctets.65 = Counter64: 0
IF-MIB::ifHCOutOctets.66 = Counter64: 0
IF-MIB::ifHCOutOctets.67 = Counter64: 0
IF-MIB::ifHCOutOctets.68 = Counter64: 0
IF-MIB::ifHCOutOctets.69 = Counter64: 0
IF-MIB::ifHCOutOctets.70 = Counter64: 0
IF-MIB::ifHCOutOctets.71 = Counter64: 0
IF-MIB::ifHCOutOctets.72 = Counter64: 0
IF-MIB::ifHCOutOctets.73 = Counter64: 0
IF-MIB::ifHCOutOctets.74 = Counter64: 0

TDS Configuration For Qatar

Hello SAP TDS Experts,
i am working for client in Qarar recently qatar government is implimented 5% TDS on sub-controctors for that can i go for Extended withhoulding tax configuration . i have worked on configuration for india is the same congiguration setting have done for qatar also but expect bussines place and section code .
while i am posting vendor invoice system is giving withhoulding tax pup-up box in simulation according to tax code rate system should callacute and credited to TDS Payable account this thing is not happening,
while i am posting vendor invoice system is giving withhoulding tax pup-up box in that withhoulding base amount and tax amount if i am entring manualy in simulation mode enterd tax amount getting credited to TDS Payable account.
I am not able to find the mistake for automatic callucatin of tax amount based on the given withhoulding code
Please help me out

Hi Guru,
can you share stps to be follow TDS configuration for qatar, my client wants it from sap now.
if anybody configured for qatar, please share with me how to follow the procedure, is it similar to India TDS or any thing new steps to add.
it is great helpful
Regards
Anil

SAP DMS - How to do an external DMS configuration for the existing system ?

Hi All.
Greetings.
Request help and understanding.
Am new to the world of SAP. And request SOME clarity for understanding of DMS.
We are wanting to put an external DMS server and wish to configure for the same.
So that the load on the production SAP R/3 database is reduced.
We are now wanting to test the same on Dev environment.
From SDN Link :
I understand that :
DMS basically has a content server. which stores documents.
That can be accessed through Web, SAP R/3 Gui , SAP Portal.
I have gone thro various links and the following links i have found to be informative and helpful :
http://help.sap.com/saphelp_erp60_sp/helpdata/en/c1/1c31a243c711d1893e0000e8323c4f/frameset.htm
http://wiki.sdn.sap.com/wiki/display/PLM/DMS+Customizing
http://help.sap.com/saphelp_nw70/helpdata/en/59/fba637fcf7dc39e10000009b38f8cf/frameset.htm
However, would like to know the following because am not getting the clarity :
1) Is there any supported platform / compatibility guide for DMS ?
if yes, can someone send me the link?
2) We have oracle 11g as our for SAP R/3 backend.
Windows 2003 server 64 bit system.
When i check the system status on the dev server of sap.
It says. ECC 6.0 Rel 7.00 update 20 (hOpe am reading it correctly)
After much search on the SMP site,
we finally discovered and downloaded the DMS software for unicode and / 64 bit.
Which we saw under the maintenance components separately seen for DMS 7.0
Now for this DMS content server which we would like to make it external for storage of documents -
do we need to have a separate database for this purpose as a repository.
If i run a setup of DMS - will that automatically install any default repository for this or
will it allow me to choose any other repository for the same ?
Can anyone advise on this.
Because this link says content server is based on Instance of MAXDB : http://help.sap.com/saphelp_nw70/helpdata/en/59/fba637fcf7dc39e10000009b38f8cf/frameset.htm
3) I read some thing like this on some of the SDN links :
P40 - Integration of DMS
P62 - R&D Document Manage¬ment and Workflow
P71 - Document management
What are they referring to.
4) We would be accessing these thro web, gui, customised portal.
This content server configuration is a bit confusing.
5) Is SNC configuration required to be done for the separate DMS server setup.
If yes, how to do that ? any configuration link for that please ?
Can anyone advise on the things to do.
Steps to do.
What all are the pre-requisites to check, before we start the set up of DMS.
Can anyone help me understand this whole thing regarding the DMS installation and configuration.
Step-wise.. from the start to end.
Because it gives me a lot of uneasiness without having everything in place before we could say we could start the whole process of configuration / installation.
Many thanks for your help in advance.
Wishing you a happy and relaxed weekend.
Kind regards
Indu

Thanks christoph & pradeep kumar.
did a few more research and atleast have come to understand that.
DMS server installation has content server which works only with MAXDB.
So my understanding is correct.
And what we see as Easy DMS is a client installation.
which probably i would look at at a later stage.
Found this link to be a little more informative :
http://www.sapfans.com/forums/viewtopic.php?f=12&t=330558
I really wish. That life were to be so easy. To call a consultant and finish it off
Wishful thinking
thanks and cheers
indu

How to have Multiple Configurations for a Flex Application

Hi All,
I've seen this question asked in various forms multiple times, but never answered: How do you set up a FLEX configuration to have different configurations for development (local), test server, staging server, beta server, and production server? I cannot imagine that Adobe has not accounted for this, something that is very standard in most development teams. Zend Framework has a very elegant solution for this: in the configuration file you define all aspects that can be configured, as well as the various environments (development, staging, beta, live, etc.). Then, in the bootstrap file you specify which environment you want to work in, and you're all set.
How can something like this be achieved in FLEX?
Many thanks!
-Mike

Maybe my setup is unconventional, I doubt it, though:
1) SVN repo stores FLEX and PHP codebases in separate projects.
2) Developer gets code from repo, and runs on local machine. -> need to configure FLEX to point to local PHP code here for Remote Objects.
3) Developer then publishes Flex app to staging server. -> need to configure FLEX to point to staging PHP code here.
4) Flex app then gets published to live server. -> need to configure FLEX to point to live PHP code here.
Now, using ANT, the scenario would look like this:
1) SVN repo stores FLEX and PHP codebases in separate projects.
2) Developer gets code from repo, and runs on local machine. -> need to configure FLEX to point to local PHP code here for Remote Objects.
3) Code is good and developer checks it back into SVN.
4) ANT extracts latest build from SVN and builds it, then publishes to staging server. -> need to configure FLEX to point to staging PHP code.
I am using PHPUnderControl as my build server for PHP.
I am also unclear as to how my goal could be achieved using ANT?
Thanks!
Mike

ASA 5505 configured for WebVPN connecting to Citrix Web Interface

ASA 5505 configured for WebVPN connecting to Citrix Web Interface.
i have a ASA 5505 that I am attempting to configure for WebVPN with passthrough into Web Interface . The user authenticates into WebVPN OK and gets the option to click on the Citrix Link (which is i add bookmark citrix server http:// 172.30.40.5.) i enter the citrix and then for example i want to open to outlook it can not open. (when i want to open some application no application is open)).there is no alarm at asa. how i solve this issue?
thanks.

Teymur,
Can you confim that after disabling the ssl/tls on the Citrix server (secure connectivity) that you are getting exactly the same error. It is possible that it is generating a different error.
The bug where we have see the existing error was CSCtf06303 but that has been fixed in 8.4.1. Can you confirm the exact version of code you are running on the ASA.
If you have confirmed the above two notes it may be adventageous to open a TAC case as we may need to do some live additional troubleshooting.
Thanks
-Jay

Financial Reporting Studio 11.1.2.1 PDF not Configured for Web Server

I have installed EPM 11.1.2.1, and HFM, Planning, Essbase, Financial Reporting are all working fine except when I do a report preview in the Workspace an error is received that PDF has not been configured for this Web Server.
I have uninstalled PDF and Financial Reporting then re-installed them but I am still getting the same error. Also, I when I tried to view report from Workspace in Financial Reporting Studio, I received the following error:
error number 400 Error Description:Form already displayed; can't show modally. Function: ShowMsg. Module:GblMethods.
Your help would be gracefully appreciated.

You should review all installation guides, readmes, and the certification matrix before performing a Hyperion Installation and/or Upgrade.
Version 9.0 of Ghostscript is not supported, install ghostscript 8.6.3 - 32-bit.
From the 11.1.2.1 Certification Matrix: "Either: --Adobe Acrobat Distiller Server 8.0 or 6.0 --GPL Ghostscript 8.63; AFPL Ghostscript 8.54 or 8.51; or GNU Ghostscript 7.0.6"
From the 11.1.2.1 Installation Guide Page 110: "Ensure that a supported 32-bit version of Ghostscript is installed."
See http://www.oracle.com/technetwork/middleware/bi-foundation/oracle-hyperion-epm-system-certific-131801.xls
http://download.oracle.com/docs/cd/E17236_01/epm.1112/epm_install_11121.pdf
Regards,
John A. Booth
http://www.metavero.com

Want to use an iPod photo configurated for Mac on a PC

I want to use my old iPod photo (configurated for Mac) on a PC (but do not need to keep my songs and photos). Is this possible? If so, what do I do?
iMac G5 Mac OS X (10.4.8) iPod 5th generation 60 GB

If your iPod is formatted for Mac it won't run natively on a PC because the Windows OS does not support the HFS Plus file system and therefore will not see the drive. Macs can read Windows drives so you could restore and format the iPod on a PC, this would also mean any future software updates would have to be done on Windows. This will erase your drive so you need to have your songs and photos backed up. Alternatively there are third party programs that will allow you to use a Mac formatted iPod on Windows, this is one for instance gets good reviews and has the functionality to let you copy content from the iPod to the PC. Not sure if it does photos but have a look: XPlay 2
You can read another user's experience of using XPlay at this link: iPod on Mac and Windows

SAP IDES ECC 6.0 configuration for ess/mss

Hi,
Iam new to sap . i want to practice various scenarios in ess/mss in my own pc which is installed with ecc 6.0 . what are the configuration to be made in ecc 6.0 for maintaining about 10-20 users for using ess/mss scenarios. i have a knowledge on webdynpro java and little knowledge on ep and using r/3 server. The 10-20 users created should be able to use ess/mss through portal .
So, list the steps configuring for 10-20 users for using ess/mss in ecc ides 6.0 server.
Thanks & regard
prasad

<< Do not post the same question across a number of forums >>

Is it possible to run TWO parellel configurations for one Object??

SAP Gurus,
We have a strange requirement from the client to have to configurations established in the system for one configuration object.
Without taking much of your time let me paraphrase the requirements.
The client is having two different types of putaway strategies in their current business process. And they toggle between these putaway strategies by reaching out to their production support group and they make configuration changes to have the other put away strategy
One Step Putaway: GR area --> High Rack Storage
Two Step Putaway: GR area --> Interim storage (area at the end of each aisle of high rack storage) --> High Rack
Client wants to have two parallel configurations for both of these put away strategies and needs an ability to switch from one to another. This switching ability should be accessed from SAP screen without any IT intervention (no configuration)
- Switching ability should allow the warehouse manager to change from one step to two step put away strategies without any IT intervention.
- Switching ability should be accessed my SAP Screen (Z-transaction or something with a radio button to toggle around)
Is it possible to have two configuration made for Putaway Strategies and switch them on/off depending on the warehouse needs??
Your invaluable feedback on this will be highly appreciated.
Thanks again folks,
Dhaval
Edited by: Dhaval Joshi on Mar 4, 2008 12:09 PM

Q1--I don't believe it is possible. An organization can have multiple licenses tied to its main email address, for example, but then they are assigned to the individual users.
Q2--Yes, you would just need to log out of your account within the CC desktop app prior to logging in on the other account.
If you have any questions, feel free to reach out.

How can I list all the domains configured for Weblogic Servers?

How can I list all the domains configured for Weblogic Servers?
I saw a note, which says the following:
"WebLogic Server does not support multi-domain interaction using either the Administration Console, the weblogic.Admin utility, or WebLogic Ant tasks. This restriction does not, however, explicitly preclude a user written Java application from accessing multiple domains simultaneously."
In my case, I just want to list all the domains, is that possible by using any scripts?
Thanks
AJ

If you use WLS Node Manager and the Config Wizard was used to create the domains, then the list of domains should be in a location like this:
<MIDDLEWARE_HOME>\wlserver_10.3\common\nodemanager\nodemanager.domains
Enterprise Manager Grid Control also has support for multi-domain management of WLS in a console.

How to get the number of decimal places configured for a site column

Hi,
I have a column 'SampleNumCol' of type Number, the number of decimal places to be displayed is configured as 2.
The column conatins a value, but when retrieved programatically is displayed as 5.00000000 instead of 5.00.
I am retrieving this column using listitem.Properties[field.InternalName].
I need to trim the decimals based on number of decimal places configured for the site column.
How to get the number of decimal places configured for a site column?
Thanks in advance,
dhijit

Get the field as SPFieldNumber and then check DisplayFormat which returns
SPNumberFormatTypes
SPFieldNumber numberField = list.Fields.GetFieldByInternalName("YourNumberFieldName") as SPFieldNumber;
SPNumberFormatTypes numFormatType = numberField.DisplayFormat;

Getting SPWeb.CurrentUser as null with Windows Authentication (AD), when configured for Claims Authentication

Hi All,
We recently migrated to SP 2013 from SP 2010. We are using most of the OOB features, with a few custom code. We have implemented a custom ASP.NET Membership Provider that authenticates against a web service. This was working fine on SP 2010.
The entire code base was migrated to SP 2013 (with .net fw 4.5, etc) and any issues Compile / Runtime were fixed. However, we are stuck at one bug, which seems to be occuring only while trying to login with Windows Authentication. When a user tries to login
with Forms Authentication, the error is never noticed.
Scenrio: Login as Windows Authentiction.
Result: The user is signed into the system and is authenticated against the AD. For random page loads - it throws access denied (even though he is a site collection admin). While attaching a debugger, we found that, at times the SPWeb.CurrentUser is null (weird).
At the same time, the HttpContext.Current.Request.IsAuthenticated returns true. Which means the User is Authenticated, but not available in the SPWeb.CurrentUser object.
Attached are couple of ULS Logs that we found. The line which says IsAuthenticated=True, UserIdentityName=, ClaimsCount=0 is a little disturbing. Can you please let me know what is happening here? I am not able to access the root site (http://win2012d2:1234/)
however, i am able to access (http://win2012d2:1234/SitePages/Home.aspx) just fine, without any issues.
Please note, this error is only when the user is logged into sharepoint as a windows user. The forms user faces no such issues.
ULS Logs:
Name=Request (GET:http://win2012d2:1234/)
Non-OAuth request. IsAuthenticated=True, UserIdentityName=, ClaimsCount=0
Application error when access /, Error=Exception of type 'System.ArgumentException' was thrown. Parameter name: encodedValue
at Microsoft.SharePoint.Administration.Claims.SPClaimEncodingManager.DecodeClaimFromFormsSuffix(String encodedValue)
at Microsoft.SharePoint.Administration.Claims.SPClaimProviderManager.GetProviderUserKey(IClaimsIdentity claimsIdentity, String encodedIdentityClaimSuffix)
at Microsoft.SharePoint.Administration.Claims.SPClaimProviderManager.GetProviderUserKey(String encodedIdentityClaimSuffix)
at Microsoft.SharePoint.Utilities.SPUtility.GetFullUserKeyFromLoginName(String loginName)
at Microsoft.SharePoint.ApplicationRuntime.SPHeaderManager.AddIsapiHeaders(HttpContext context, String encodedUrl, NameValueCollection headers)
at Microsoft.SharePoint.ApplicationRuntime.SPRequestModule.PreRequestExecuteAppHandler(Object oSender, EventArgs ea)
at System.Web.HttpApplication.SyncEventExecutionStep.System.Web.HttpApplication.IExecutionStep.Execute()
at System.Web.HttpApplication.ExecuteStep(IExecutionStep step, Boolean& completedSynchronously)
Getting Error Message for Exception System.ArgumentException: Exception of type 'System.ArgumentException' was thrown. Parameter name: encodedValue
at Microsoft.SharePoint.Administration.Claims.SPClaimEncodingManager.DecodeClaimFromFormsSuffix(String encodedValue)
at Microsoft.SharePoint.Administration.Claims.SPClaimProviderManager.GetProviderUserKey(IClaimsIdentity claimsIdentity, String encodedIdentityClaimSuffix)
at Microsoft.SharePoint.Administration.Claims.SPClaimProviderManager.GetProviderUserKey(String encodedIdentityClaimSuffix)
at Microsoft.SharePoint.Utilities.SPUtility.GetFullUserKeyFromLoginName(String loginName)
at Microsoft.SharePoint.ApplicationRuntime.SPHeaderManager.AddIsapiHeaders(HttpContext context, String encodedUrl, NameValueCollection headers)
at Microsoft.SharePoint.ApplicationRuntime.SPRequestModule.PreRequestExecuteAppHandler(Object oSender, EventArgs ea)
at System.Web.HttpApplication.SyncEventExecutionStep.System.Web.HttpApplication.IExecutionStep.Execute()
at System.Web.HttpApplication.ExecuteStep(IExecutionStep step, Boolean& completedSynchronously)
[Forced due to logging gap, Original Level: Verbose] Looking up {0} site {1} in the farm {2}
Unknown SPRequest error occurred. More information: 0x80070005
SPRequest.GetPageListId: UserPrincipalName=, AppPrincipalName= ,bstrUrl=http://win2012d2:1234/
System.UnauthorizedAccessException: Access is denied. (Exception from HRESULT: 0x80070005 (E_ACCESSDENIED)), StackTrace:
at Microsoft.SharePoint.SPContext.get_ListId()
at Microsoft.SharePoint.SPContext.get_List()
at Microsoft.SharePoint.WebControls.ScriptLink.InitJs_Register(Page page)
at Microsoft.SharePoint.WebControls.ScriptLink.RegisterForControl(Control ctrl, Page page, String name, Boolean localizable, Boolean defer, Boolean loadAfterUI, String language, Boolean injectNoDefer, Boolean controlRegistration, Boolean loadInlineLast,
Boolean ignoreFileNotFound)
at Microsoft.SharePoint.WebControls.ScriptLink.Register(Control ctrl, Page page, String name, Boolean localizable, Boolean defer, Boolean loadAfterUI, String language, String uiVersion, String ctag)
at Microsoft.SharePoint.WebControls.ScriptLink.Register(String uiVersion, Control ctrl, Page page, String name, Boolean localizable, Boolean defer)
at Microsoft.SharePoint.WebControls.ScriptLink.Register(Control ctrl, Page page, String name, Boolean localizable, Boolean defer)
at Microsoft.SharePoint.WebControls.ScriptLink.GetOnDemandScriptKey(String strKey, String strFile, Boolean registerDependencies, Control ctrl, Page page)
at Microsoft.SharePoint.WebControls.ScriptLink.RegisterOnDemand(Control ctrl, Page page, String strKey, String strFile, Boolean localizable)
at Microsoft.SharePoint.WebControls.ScriptLink.RegisterOnDemand(Page page, String strFile, Boolean localizable)
at Microsoft.SharePoint.WebControls.ScriptLink.RegisterForControl(Control ctrl, Page page, String name, Boolean localizable, Boolean defer, Boolean loadAfterUI, String language, Boolean injectNoDefer, Boolean controlRegistration, Boolean loadInlineLast,
Boolean ignoreFileNotFound)
at Microsoft.SharePoint.WebControls.ScriptLink.Register(Control ctrl, Page page, String name, Boolean localizable, Boolean defer, Boolean loadAfterUI, String language, String uiVersion, String ctag)
at Microsoft.SharePoint.WebControls.ScriptLink.RegisterOnDemand(Control ctrl, Page page, String strKey, String strFile, Boolean localizable)
at Microsoft.SharePoint.WebControls.ScriptLink.OnLoad(EventArgs e)
at System.Web.UI.Control.LoadRecursive()
at System.Web.UI.Control.LoadRecursive()
at System.Web.UI.Control.LoadRecursive()
at System.Web.UI.Control.LoadRecursive()
at System.Web.UI.Control.LoadRecursive()
at System.Web.UI.Page.ProcessRequestMain(Boolean includeStagesBeforeAsyncPoint, Boolean includeStagesAfterAsyncPoint)
at System.Web.UI.Page.ProcessRequest(Boolean includeStagesBeforeAsyncPoint, Boolean includeStagesAfterAsyncPoint)
at System.Web.UI.Page.ProcessRequest()
at System.Web.UI.Page.ProcessRequest(HttpContext context)
at System.Web.HttpServerUtility.ExecuteInternal(IHttpHandler handler, TextWriter writer, Boolean preserveForm, Boolean setPreviousPage, VirtualPath path, VirtualPath filePath, String physPath, Exception error, String queryStringOverride)
at System.Web.HttpServerUtility.Execute(String path, TextWriter writer, Boolean preserveForm)
at System.Web.HttpServerUtility.Transfer(String path)
at Microsoft.SharePoint.Utilities.SPUtility.TransferToErrorPage(String message, String linkText, String linkUrl)
at Microsoft.SharePoint.ApplicationRuntime.SPRequestModule.ErrorHandler(HttpApplication app, Boolean errorIsOnErrorPage)
at Microsoft.SharePoint.ApplicationRuntime.SPRequestModule.ErrorAppHandler(Object oSender, EventArgs ea)
at System.EventHandler.Invoke(Object sender, EventArgs e)
at System.Web.HttpApplication.RaiseOnError()
at System.Web.HttpApplication.PipelineStepManager.ResumeSteps(Exception error)
at System.Web.HttpApplication.BeginProcessRequestNotification(HttpContext context, AsyncCallback cb)
at System.Web.HttpRuntime.ProcessRequestNotificationPrivate(IIS7WorkerRequest wr, HttpContext context)
at System.Web.Hosting.PipelineRuntime.ProcessRequestNotificationHelper(IntPtr rootedObjectsPointer, IntPtr nativeRequestContext, IntPtr moduleData, Int32 flags)
at System.Web.Hosting.PipelineRuntime.ProcessRequestNotification(IntPtr rootedObjectsPointer, IntPtr nativeRequestContext, IntPtr moduleData, Int32 flags)
at System.Web.Hosting.UnsafeIISMethods.MgdIndicateCompletion(IntPtr pHandler, RequestNotificationStatus& notificationStatus)
at System.Web.Hosting.UnsafeIISMethods.MgdIndicateCompletion(IntPtr pHandler, RequestNotificationStatus& notificationStatus)
at System.Web.Hosting.PipelineRuntime.ProcessRequestNotificationHelper(IntPtr rootedObjectsPointer, IntPtr nativeRequestContext, IntPtr moduleData, Int32 flags)
at System.Web.Hosting.PipelineRuntime.ProcessRequestNotification(IntPtr rootedObjectsPointer, IntPtr nativeRequestContext, IntPtr moduleData, Int32 flags)
SPRequest.OpenWeb: UserPrincipalName=, AppPrincipalName= ,bstrUrl=http://win2012d2:1234/
System.UnauthorizedAccessException: Access is denied. (Exception from HRESULT: 0x80070005 (E_ACCESSDENIED)), StackTrace:
at Microsoft.SharePoint.SPWeb.InitWeb()
at Microsoft.SharePoint.SPWeb.get_WebTemplateConfiguration()
at Microsoft.SharePoint.WebControls.ScriptLink.InitJs_Register(Page page)
at Microsoft.SharePoint.WebControls.ScriptLink.RegisterForControl(Control ctrl, Page page, String name, Boolean localizable, Boolean defer, Boolean loadAfterUI, String language, Boolean injectNoDefer, Boolean controlRegistration, Boolean loadInlineLast,
Boolean ignoreFileNotFound)
at Microsoft.SharePoint.WebControls.ScriptLink.Register(Control ctrl, Page page, String name, Boolean localizable, Boolean defer, Boolean loadAfterUI, String language, String uiVersion, String ctag)
at Microsoft.SharePoint.WebControls.ScriptLink.Register(String uiVersion, Control ctrl, Page page, String name, Boolean localizable, Boolean defer)
at Microsoft.SharePoint.WebControls.ScriptLink.Register(Control ctrl, Page page, String name, Boolean localizable, Boolean defer)
at Microsoft.SharePoint.WebControls.ScriptLink.GetOnDemandScriptKey(String strKey, String strFile, Boolean registerDependencies, Control ctrl, Page page)
at Microsoft.SharePoint.WebControls.ScriptLink.RegisterOnDemand(Control ctrl, Page page, String strKey, String strFile, Boolean localizable)
at Microsoft.SharePoint.WebControls.ScriptLink.RegisterOnDemand(Page page, String strFile, Boolean localizable)
at Microsoft.SharePoint.WebControls.ScriptLink.RegisterForControl(Control ctrl, Page page, String name, Boolean localizable, Boolean defer, Boolean loadAfterUI, String language, Boolean injectNoDefer, Boolean controlRegistration, Boolean loadInlineLast,
Boolean ignoreFileNotFound)
at Microsoft.SharePoint.WebControls.ScriptLink.Register(Control ctrl, Page page, String name, Boolean localizable, Boolean defer, Boolean loadAfterUI, String language, String uiVersion, String ctag)
at Microsoft.SharePoint.WebControls.ScriptLink.RegisterOnDemand(Control ctrl, Page page, String strKey, String strFile, Boolean localizable)
at Microsoft.SharePoint.WebControls.ScriptLink.OnLoad(EventArgs e)
at System.Web.UI.Control.LoadRecursive()
at System.Web.UI.Control.LoadRecursive()
at System.Web.UI.Control.LoadRecursive()
at System.Web.UI.Control.LoadRecursive()
at System.Web.UI.Control.LoadRecursive()
at System.Web.UI.Page.ProcessRequestMain(Boolean includeStagesBeforeAsyncPoint, Boolean includeStagesAfterAsyncPoint)
at System.Web.UI.Page.ProcessRequest(Boolean includeStagesBeforeAsyncPoint, Boolean includeStagesAfterAsyncPoint)
at System.Web.UI.Page.ProcessRequest()
at System.Web.UI.Page.ProcessRequest(HttpContext context)
at System.Web.HttpServerUtility.ExecuteInternal(IHttpHandler handler, TextWriter writer, Boolean preserveForm, Boolean setPreviousPage, VirtualPath path, VirtualPath filePath, String physPath, Exception error, String queryStringOverride)
at System.Web.HttpServerUtility.Execute(String path, TextWriter writer, Boolean preserveForm)
at System.Web.HttpServerUtility.Transfer(String path)
at Microsoft.SharePoint.Utilities.SPUtility.TransferToErrorPage(String message, String linkText, String linkUrl)
at Microsoft.SharePoint.ApplicationRuntime.SPRequestModule.ErrorHandler(HttpApplication app, Boolean errorIsOnErrorPage)
at Microsoft.SharePoint.ApplicationRuntime.SPRequestModule.ErrorAppHandler(Object oSender, EventArgs ea)
at System.EventHandler.Invoke(Object sender, EventArgs e)
at System.Web.HttpApplication.RaiseOnError()
at System.Web.HttpApplication.PipelineStepManager.ResumeSteps(Exception error)
at System.Web.HttpApplication.BeginProcessRequestNotification(HttpContext context, AsyncCallback cb)
at System.Web.HttpRuntime.ProcessRequestNotificationPrivate(IIS7WorkerRequest wr, HttpContext context)
at System.Web.Hosting.PipelineRuntime.ProcessRequestNotificationHelper(IntPtr rootedObjectsPointer, IntPtr nativeRequestContext, IntPtr moduleData, Int32 flags)
at System.Web.Hosting.PipelineRuntime.ProcessRequestNotification(IntPtr rootedObjectsPointer, IntPtr nativeRequestContext, IntPtr moduleData, Int32 flags)
at System.Web.Hosting.UnsafeIISMethods.MgdIndicateCompletion(IntPtr pHandler, RequestNotificationStatus& notificationStatus)
at System.Web.Hosting.UnsafeIISMethods.MgdIndicateCompletion(IntPtr pHandler, RequestNotificationStatus& notificationStatus)
at System.Web.Hosting.PipelineRuntime.ProcessRequestNotificationHelper(IntPtr rootedObjectsPointer, IntPtr nativeRequestContext, IntPtr moduleData, Int32 flags)
at System.Web.Hosting.PipelineRuntime.ProcessRequestNotification(IntPtr rootedObjectsPointer, IntPtr nativeRequestContext, IntPtr moduleData, Int32 flags)

Hi Mohamed,
According to your description, my understanding is that the error occurred when users login with Windows Authentication.
From the error message, I recommend to check if the anonymous access is enabled for the web application.
And please also make sure that the users all are available and have permission to access the site.
Here is a similar thread for you to take a look:
http://social.technet.microsoft.com/Forums/en-US/28623bdc-a2f0-4876-9be4-9a764f106366/getting-spwebcurrentuser-as-null-with-windows-authentication-ad-when-configured-for-claims?forum=sharepointdevelopment
Best regards.
Thanks
Victoria Xia
TechNet Community Support

MM configurations for SAP AFS System

Hi,
        I'm working in MM configuration for SAP AFS production system, After uploading AFS Materials successfully and also created Purchase order to make a stock for that material, but PO created successfully but not able to do Goods receipts for created PO.
       Errors : Purchase order xxxxx has no items,
Once created sales order for the same material again we got the error while GR but error is different.
      GR is not possible for this PO number.
But material type is ROH , and its external procurement only.
Please let me know when we will get this type of errors.
Thanks and regards
Nisar.

Hi Nasir;
Some possible causes are;
1.     Defining inbound delivery (Or kind of a confirmation) in the PO LI level and not maintaining the document subsequently
2.     Not releasing the PO before the GRN
3.     Creating the PO with a material with Grids (AFS Basic Data Screen) and not maintaining the grid value at item detail level of the PO
Azwath Mohammad
http://www.sapafs.net

SCOM 2012 R2 Error The connector the module is configured for no longer exists

Hi All,
The Microsoft Operations Manager Connector Framework Alert Forwarding module failed to mark an alert for forwarding because the connector the module is configured for no longer exists.
Connector Id: 57a14deb-a74b-520e-ac32-ba8d340d112d

Hi Mark,
You can try the following steps,
This is because we have deleted a connector that still had a live subscription associated with it. We need to go and delete that subscription to clean this up. The problem is – the connector is gone, so the subscription is no longer available
in the UI.
Therefore – we will have to delete it manually. This subscription (as all subscriptions) is kept in the “Notifications Internal Library” MP. You need to export that MP to XML. FIRST MAKE A BACKUP COPY OF THIS FILE IN CASE YOU MESS UP, then
open it for editing in Notepad, or your XML editor of choice.
All subscriptions in this MP are kept in the <Monitoring> <Rules> section. To identify which connector subscription RULE is causing the problem – you can search for the connector ID, from the event 11502 above. In my example – my connector
ID from this event is: b7a64deb-f7ff-440e-bc30-d08d340dfe8d.
So – I search the XML for that string – and find b7a64deb-f7ff-440e-bc30-d08d340dfe8d in the <WriteActions> section of a specific <Rule>:
<WriteActions>
<WriteAction ID="WA" TypeID="SystemCenter!Microsoft.SystemCenter.ConnectorFrameworkAlertWriteAction">
<ConnectorId>{b7a64deb-f7ff-440e-bc30-d08d340dfe8d}</ConnectorId>
</WriteAction>
</WriteActions>
Good – I have identified the problem. Now – I need to do two things:
Find the rule ID – to identify the display string associated with it… then delete that display string.
Delete the orphaned subscription rule.
So – I move up in the XML section of this rule – and I find my Rule ID. (here is mine:)
<Rule ID="ProductConnectorSubscription2850f8e3_afe7_4c36_84d2_ee258bd086eb"
I then search for the part above which I bolded in blue (yours will be different – search for your string)
What this finds – is the display string section of the XML – which maps this GUID ID to the common name that you gave the subscription. (here is mine:)
<DisplayString ElementID="ProductConnectorSubscription2850f8e3_afe7_4c36_84d2_ee258bd086eb">
<Name>Process All New Alerts</Name>
</DisplayString>
So – I need to DELETE this section from the XML…. just the section above, from my very specific <DisplayString ElementID="ProductConnectorSubscription2850f8e3<GUID> line, to the very next </DisplayString>.
Next – I need to delete the entire <rule> which contains the subscription we want to remove. Mine will be from:
<Rule ID="ProductConnectorSubscription<GUID> line to the very next </Rule>
When you are happy – you can import this XML MP back into the management group. It should import with no errors. If you get an error – you made a mistake when editing the XML. You can look on the RMS event log for the specific problem – there
will be a critical event there if it fails to import.
second part for this link
http://blogs.technet.com/b/kevinholman/archive/2009/09/10/removing-an-old-product-connector.aspx
Regards, Ibrahim Hamdy

STP Configuration for SG300/SF300

Similar Messages

Maybe you are looking for