Strange behavior with Cisco AP and Intel 3945 wireles card

Hi,
I have an interesting problem with an Intel 3945 A/G card, and my cisco APs.
1. Given:
Cisco 1100 and 1200 AP running IOS 12.3.8-JEA
Two laptop, one with Intel 2200 MPCI Card, the other with Intel 3945 MPCI Card
Microsoft AD with IAS radius server
a. 1 SSID with Simple EAP-TLS configuration Enterprise WPA/TKIP, no vlans, broadcast SSID. both card associate correctly and operate normally.
b. 2 SSID, 1 with simple EAP-TLS configuration Enterprise WPA/TKIP (broadcast), and 2nd SSID Open/No encryption/No authentication (not broadcasted), both cards associate correctly and operate normally.
c. 2 SSID, 1 with simple EAP-TLS configuration Enterprise WPA/TKIP (broadcast), and 2nd SSID WPS-PSK (not broadcasted), both cards operate normally.
Now it gets interesting:
c. 2 SSID, 1 with EAP-TLS/WPA Enterprise on its own VLAN 102, 2nd SSID Open/No Encryption/No authentication on a separate VLAN 105, VLAN 1 is used for admin and radius backhaul to IAS.
If both SSID are broadcasted via mbssid guest-mode both Intel cards work as expected
If neither SSID are broadcasted, both Intel cards work as expected
If either SSID is broadcasted via normal guest-mode command, the Intel 2200 associates and works correctly, but the Intel 3945 refuses to assocate to the AP.
Has anyone heard of side-effect?
Alan

I'm seeing a similar issue with the 3945 right now. However in my example the following is the case;
APs are 1200 series IOS upgraded running 802.11b interfaces only. There are multiple SSIDs NONE of which are broadcasting.
We've got a few different client types. The Cisco CB21ABG cards are fine, as are the Intel 2200 and 7920 phones. It's only the 3945 that has a problem and it's running Intel's 10.5.1.68 driver which is the latest. I'm considering downgrading it to an older driver.
Anybody got a definate fix for this Intel card???

Similar Messages

WRT110 crashes with Vista SP1 and Intel 3945

I have a WRT110 with the latest firmware 1.0.4, an a Dell XPS1330 with the Intel 3945abg wireless card and the latest drivers in Intel. When ever my laptop tries to connect the router crashes and drops all other connections with other wireless devies and wired devices. I also have another laptop running XP that works great on the wireless connection. It's same to say the problem is limited to the Vista machine and the Intel 3945 wireless card. Now sure what to do?

I have the same problem. Took me a while to figure out that when i connected my Toshiba laptop with Vista and Intel 3945 Router and network crashed couldnot even get the router accessed on hardwired computer. Everything returns back to normal when laptop disconnected from wireless network
Customer support was not able to help, called them twice. I solved by connecting an old wireless router to one of the ports of Linksys and connect my Vista laptop on that wireless network. That is not really a solution but if you'd like to, return the router until they can at least admit that there is a problem with compatibility, upgrading firmware on wireless adaptor did not help.
(Mod note: Edited for guideline compliance.)
Message Edited by kent07 on 11-06-2008 06:33 PM

Strange behavior with Quick Cluster and one shared machine

Hi, I've been struggling for a while with my compressor 4.0.7 distributed processing setup... Here is my configuration:
1 Mac Mini running as a Quick Cluster with services (3 instances of compressor shared)
1 Macbook Pro running Services Only (7 instances of compressor shared)
1 Macbook Pro (much older) running Services Only (2 instances of compressor shared)
All 3 systems are running Mavericks, but I had this same problem when all 3 were Mountain Lion.. Had to trash the app and all of the prefs in Library\Application Support\Apple Qmaster and Compressor and reinstall to get the app running on all of the upgraded machines, so a fresh start didn't fix this issue.
The Mac Mini and the older Macbook Pro can see the cluster, submit jobs and are both utilized for rendering when jobs are submitted from the Mini or the older Macbook Pro
The newer MBP can see the cluster in Share Monitor and in qadministrator, but cannot see any of the jobs in the history (the other Macbook Pro can see all details identically to the Mac Mini). When a job gets submitted from this system it appears as "Not Available" on the Mac Mini share monitor and it only utilizes 1 local process to do the rendering, which stalls out after about 1 minute. Activity Monitor shows all 7 instances of compressord are running and not frozen but have no activity.
Jobs submitted from the Mini and older MBP attempt to use the newer MBP for distributed rendering but stall out after about 30 seconds with a host error. The shared volume never appears on the newer MBP. Qadministrator on the Mini can see the newer MBP and all of the listed services as available.
Now here is the part that really blows my mind:
After submitting a job to the cluster from the newer MBP, which will stall out and need to be cancelled as mentioned above; submitting a job from the mini will actually successfully use the services on the newer MBP. Share monitor on the newer MBP still does not display any jobs on the server cluster. Rebooting the newer MBP puts me right back in the "I won't play with those other macs" tantrum.
Anyone else see this issue and have a fix for it? Workarounds are nice but this is very, very annoying when I get into crunch time.

Do you have log files?
          - Prasad
          Chris Dempsey wrote:
          > We have 2 WebLogic 4.5.1 servers in a cluster with none of the Service
          > Packs installed. When a client uses the deployed entity beans or
          > servlets they work every other time. The times they do not work nothing
          > happens. No exceptions, no responses to the client ( i.e. HTTP 404s ),
          > nothing. I suspect something in the cluster setup since we do not have
          > these same problems on non-clustered entity beans or servlets. We have
          > made sure all the entity beans have the Shared Database flag set on and
          > added the delayUpdatesUntilEndOfTx false to the enviroment of the DD.
          > That didn't fix the problem. Any ideas?
          >
          > Thanks in advance,
          > Dallas Dempsey
          > DEM - Houston, TX

Strange behavior with entity beans and servlets in a cluster

We have 2 WebLogic 4.5.1 servers in a cluster with none of the Service
          Packs installed. When a client uses the deployed entity beans or
          servlets they work every other time. The times they do not work nothing
          happens. No exceptions, no responses to the client ( i.e. HTTP 404s ),
          nothing. I suspect something in the cluster setup since we do not have
          these same problems on non-clustered entity beans or servlets. We have
          made sure all the entity beans have the Shared Database flag set on and
          added the delayUpdatesUntilEndOfTx false to the enviroment of the DD.
          That didn't fix the problem. Any ideas?
          Thanks in advance,
          Dallas Dempsey
          DEM - Houston, TX


Do you have log files?
          - Prasad
          Chris Dempsey wrote:
          > We have 2 WebLogic 4.5.1 servers in a cluster with none of the Service
          > Packs installed. When a client uses the deployed entity beans or
          > servlets they work every other time. The times they do not work nothing
          > happens. No exceptions, no responses to the client ( i.e. HTTP 404s ),
          > nothing. I suspect something in the cluster setup since we do not have
          > these same problems on non-clustered entity beans or servlets. We have
          > made sure all the entity beans have the Shared Database flag set on and
          > added the delayUpdatesUntilEndOfTx false to the enviroment of the DD.
          > That didn't fix the problem. Any ideas?
          >
          > Thanks in advance,
          > Dallas Dempsey
          > DEM - Houston, TX

Strange behavior with DefaultCellEditor

Hello everybody,
I found a strange behavior with DefaultCellEditor using a JTextField in a JTable. The following line will show, what I mean:
setDefaultCellEditor(String.class,new DefaultCellEditor(new JTextField()));
Imho this should do the same as JTable does already, when it installs a JTextField as default cell editor for cell values of the String class. But, it seems, that it is not the same:
When I add this line in the constructor of a JTable subclass the editor component seems to be less wide and less high to the right and bottom - it looks so with Win95 with JDK 1.4.0 - but with Win2000 it is correct for example.
My question is - how can it be, that the normal default cell editor does not have this behavior but when I use the line above, it is displayed in the wrong way?- What does the default cell editor in another way than I do it, that it has not this ugly display?
I would like to look in the sources, but unfortunately I can't find the source code in JDK 1.4.0 - perhaps you have a hint, where to find it.
greetings Marsian

It seems the Label doesn't like it, that it is in a GridCell with rowspan = 2
If it is in a normal cell (no rowspan), it works.
If I add ColumnConstraints to the gridpane, it kind of works, but the Label still occupies more space than it should.
Edited by: csh on 19.07.2012 03:51

Strange behavior with Collections

Hello!
I have a - from my point of view - strange behavior with a List (same also applies to Vector, LinkedList, and others):
List<String> myList = new myList<String>;
myList.add("One");
while (true) {
try {
System.out.println(myList.size());
throw new Exception();
} catch (Exception e) {
e.printStackTrace();
}And the result is 1, 2, 2, 2, ...although I added only one element. The two elements in the List point to the same object.
What could case this issue?
Regards,

len00x wrote:
List<String> myList = new myList<String>;This doesn't even look like it will compile for at least one reason, easily two.

Strange behavior with Label#setWrapText(true) in GridPane.

I've got a strange behavior with a Label, which has setWrapText(true) in a GridPane.
Check out the sample and click the button.
You see, that the GridPane suddenly behaves as if it had GridPane.setVGrow and HGrow set for the lblStatus.
(it takes the full available space).
Furthermore the first column shrinks to a minimum, so that lblText1 can't display its text anymore.
Tested with 2.1 GA.
Any help with that?
import javafx.application.Application;
import javafx.event.ActionEvent;
import javafx.event.EventHandler;
import javafx.geometry.Insets;
import javafx.scene.Scene;
import javafx.scene.control.Button;
import javafx.scene.control.Label;
import javafx.scene.layout.GridPane;
import javafx.stage.Stage;
public class TestApp4 extends Application {
    public static void main(String[] args) {
        launch(args);
    @Override
    public void start(final Stage stage) throws Exception {
        GridPane gridPane = new GridPane();
        gridPane.setPadding(new Insets(2, 2, 2, 2));
        Label lblText1 = new Label();
        lblText1.textProperty().set("Some text");
        Label lblText2 = new Label();
        lblText2.textProperty().set("Some other text");
        Button btnClick = new Button();
        btnClick.textProperty().set("Click me");
        final Label lblStatus = new Label();
        lblStatus.setWrapText(true);
        gridPane.add(lblText1, 0, 0, 1, 1);
        gridPane.add(lblText2, 1, 0);
        gridPane.add(lblStatus, 0, 2, 2, 1);
        gridPane.add(btnClick, 0, 3, 2, 1);
        btnClick.setOnAction(new EventHandler<ActionEvent>() {
            @Override
            public void handle(ActionEvent actionEvent) {
                lblStatus.setText("very long text, very long text, very long text, very long text,very long text, very long text");
        gridPane.setGridLinesVisible(true);
        Scene scene = new Scene(gridPane, 300, 300);
        stage.setScene(scene);
        stage.show();
}Edited by: csh on 19.07.2012 03:35

It seems the Label doesn't like it, that it is in a GridCell with rowspan = 2
If it is in a normal cell (no rowspan), it works.
If I add ColumnConstraints to the gridpane, it kind of works, but the Label still occupies more space than it should.
Edited by: csh on 19.07.2012 03:51

Strange behavior with Bindings??

Hello to all JavaFX 2 Binding experts,
I have a strange behavior with Bindings in JavaFX 2.2 (Java 1.7 update 21). Please have a look at the following source code:
package test;
import javafx.application.Application;
import javafx.beans.binding.BooleanBinding;
import javafx.beans.property.SimpleBooleanProperty;
import javafx.beans.value.ChangeListener;
import javafx.beans.value.ObservableValue;
import javafx.fxml.FXML;
import javafx.fxml.FXMLLoader;
import javafx.scene.Parent;
import javafx.scene.Scene;
import javafx.scene.control.Label;
import javafx.scene.control.RadioButton;
import javafx.stage.Stage;
public class BindingVsProperty extends Application
    @FXML
    private RadioButton opt11;
    @FXML
    private RadioButton opt12;
    @FXML
    private RadioButton opt21;
    @FXML
    private RadioButton opt22;
    @FXML
    private Label lbl11And21;
@Override
    public void start(Stage arg0) throws Exception
        FXMLLoader l_loader = new FXMLLoader();
        l_loader.setLocation(BindingVsProperty.class.getResource("BindingVsproperty.fxml"));
        l_loader.setController(this);
        l_loader.load();
        Scene l_scene = new Scene((Parent)l_loader.getRoot());
        arg0.setScene(l_scene);
        useBinding1();
        //useBinding2();
        //useBinding3();
        arg0.show();
    private void useBinding1() // NOT WORKING - ChangeListener.changed(..) is not called
        BooleanBinding l_andOpt11Opt21 = opt11.selectedProperty().and(opt21.selectedProperty());
        l_andOpt11Opt21.addListener(new ChangeListener<Boolean>()
            @Override
            public void changed(ObservableValue<? extends Boolean> arg0, Boolean arg1, Boolean arg2)
                System.out.println("Opt 1.1 AND Opt 2.1 changed to: " + arg2);
    private void useBinding2() // OK - ChangeListener.changed(..) is called
        BooleanBinding l_andOpt11Opt21 = opt11.selectedProperty().and(opt21.selectedProperty());
        lbl11And21.visibleProperty().bind(l_andOpt11Opt21);
        l_andOpt11Opt21.addListener(new ChangeListener<Boolean>()
            @Override
            public void changed(ObservableValue<? extends Boolean> arg0, Boolean arg1, Boolean arg2)
                System.out.println("Opt 1.1 AND Opt 2.1 changed to: " + arg2);
    private void useBinding3() // NOT WORKING - ChangeListener.changed(..) is not called
        BooleanBinding l_andOpt11Opt21 = opt11.selectedProperty().and(opt21.selectedProperty());
        new SimpleBooleanProperty(false).bind(l_andOpt11Opt21);
        l_andOpt11Opt21.addListener(new ChangeListener<Boolean>()
            @Override
            public void changed(ObservableValue<? extends Boolean> arg0, Boolean arg1, Boolean arg2)
                System.out.println("Opt 1.1 AND Opt 2.1 changed to: " + arg2);
    public static void main(String[] args)
        launch(args);
<?xml version="1.0" encoding="UTF-8"?>
<?import java.lang.*?>
<?import java.util.*?>
<?import javafx.scene.control.*?>
<?import javafx.scene.layout.*?>
<?import javafx.scene.paint.*?>
<BorderPane id="BorderPane" maxHeight="-Infinity" maxWidth="-Infinity" minHeight="-Infinity" minWidth="-Infinity" prefWidth="371.0" xmlns:fx="http://javafx.com/fxml">
<center>
    <AnchorPane prefHeight="200.0" prefWidth="200.0">
      <children>
        <Label id="lblAnd" fx:id="lbl11And21" layoutX="82.0" layoutY="121.0" text="Group1 Opt1 AND Group2 Opt1 is true" textFill="#41cc00" visible="false" />
        <RadioButton fx:id="opt21" layoutX="216.0" layoutY="24.0" mnemonicParsing="false" text="Group 2 - Opt 1">
          <toggleGroup>
            <ToggleGroup fx:id="group2" />
          </toggleGroup>
        </RadioButton>
        <RadioButton fx:id="opt22" layoutX="216.0" layoutY="67.0" mnemonicParsing="false" text="Group 2 - Opt 2" toggleGroup="$group2" />
        <RadioButton fx:id="opt11" layoutX="29.0" layoutY="24.0" mnemonicParsing="false" text="Group 1 - Opt 1">
          <toggleGroup>
            <ToggleGroup fx:id="group1" />
          </toggleGroup>
        </RadioButton>
        <RadioButton fx:id="opt12" layoutX="29.0" layoutY="67.0" mnemonicParsing="false" text="Group 1- Opt 2" toggleGroup="$group1" />
      </children>
    </AnchorPane>
</center>
</BorderPane>
What I need for my application is the use case in useBinding1(), i.e., a BooleanBinding where several listeners are attached to. The problem is that I never get a callback in the ChangeListener if one of the RadioButton.selectedProperty() is changed.
Now I tried what happens if I use the same BooleanBinding for another binding to a property plus the listener, now the listener gets callbacks as expected! (see useBinding2() )
Than I thought may be Bindings must be bound in order to trigger listeners and tried useBinding3() where I bind the BooleanBinding to a new BooleanProperty, in this case the listener doesn't get callback anymore...
And now I'm very frustrated and hope that anyone out there can help me to understand this strange behavior.
Thanks a lot!
WhiteAntelope

All these work just fine for me: the listeners are all called as expected. Note that the listener is only invoked when the value of the binding actually changes, which doesn't happen every time a radio button is pressed. (For example, if both buttons are unselected, the binding is false. If one button is selected, the binding remains false and the listener is not invoked. When the second button is selected, the binding becomes true, and the listener is invoked.)

Strange behavior with "insertTextAsContent"

Hi,
I've got a strange behavior with this loop :
for (j = 0; j < myParagraph.characters.length-1; j++) {
     var myCharacter = myParagraph.characters[j];
     if (myCharacter.appliedFont.fontStyleName == "Regular") {
          alert(myCharacter.contents);
          myXmlElement.insertTextAsContent(myCharacter.contents, XMLElementPosition.ELEMENT_END);
I loop through every characters of a paragraph, test if they are "regular", "italic", "bold"..., and store them in different xmlElement. Everything is fine except that every double characters (in french : homme, cette, elle, ville...) output in my xmlElement as one only character (home, cete, ele, vile...). I try with "aaaaaazzzzzzeeeeeerrrrrtttttyyyyy" and it give me, the same way, "azerty" ?!
The "alert" line output the correct full sentences character by character ("h", "o", "m", "m", "e"...).
If you have any idea to explain, you are more than welcome
Thanks
** edit : don't know if it's important but I'm using CS6 **

Hi
Have you seen this in the object model viewer?
XMLElement.insertTextAsContent (using:varies, position: XMLElementPosition ): Text
Adobe InDesign CC (8.0) Object Model
Inserts the specified text as content before, in, or after the XML element.
using: Data Type: varies
The text to be inserted. Can accept: String or SpecialCharacters enumerator.
position: Data Type: XMLElementPosition
The position at which to insert the text. Note that text inserted before or after the element does not become part of the content of the element. Instead, it becomes content of the parent of the element.
Don't ask me why it works when there is no doubled character
So i tried the following and it worked. I hope this will solve your problem.
function main() {
     if (app.documents.length != 0) {
        var myDoc = app.activeDocument;
        var myParagraph = myDoc.textFrames[0].paragraphs[0];
        var myXmlElement = myDoc.xmlElements[0];
        for (j = 0; j < myParagraph.characters.length-1; j++) {
            var myCharacter = myParagraph.characters[j];
            if (myCharacter.appliedFont.fontStyleName == "Regular") {
                alert(myCharacter.contents);
                myXmlElement.contents += myCharacter.contents;
                alert(">" + myXmlElement.contents+ "<");
            }     // if
        }     //for
    }     // if
}   // main()
Kind regards
Dani (from Switzerland)

Strange behavior with csv flat file integration

Hi,
i've a real strange behavior with csv flat file integration.
I've defined the file inbound with | as separator
Here is the sender payload result, extra columns appears !
<row>
<VAL1>D</VAL1>
<VAL2 />
<VAL3>01</VAL3>
<VAL4 />
<VAL5 />
<VAL6>003160000</VAL6>
<VAL7 />
<col>003160001</col>
<col />
<col>2</col>
<col />
<col>91200604212</col>
<col />
<col>VIRTUAL DJ HOME EDITION</col>
<col />
<col>2</col>
<col />
<col>2</col>
<col />
<col />
<col>2</col>
<col />
</row>
When i changed the separator to ; in my file and in the file inbound it gives the following.
Everything is ok.
<row>
<VAL1>D</VAL1>
<VAL2>01</VAL2>
<VAL3 />
<VAL4>003160000</VAL4>
<VAL5>003160001</VAL5>
<VAL6>7</VAL6>
<VAL7>91200604212</VAL7>
<col>VIRTUAL DJ HOME EDITION</col>
<col>10</col>
<col>10</col>
<col />
<col>10</col>
</row>
Why using a different separator would change the payload ?
It will be a good thing for me if I could use the pipe separator.
Thanks

Can you give the steps you're using to get this error? I'm not seeing any problem here.
1) Create a new audio project (44.1 KHz).
2) Arm the record head in track 1 by pressing the "R" button in that track. Verify audio levels.
3) Record by pressing the record button in the audio controls.
4) Stop recording by pressing the stop button.
5) Play back the resulting audio. Sounds fine.
6) Select File > Export.
7) Change the file format to WAVE file. Change the bit depth to 16 bit, change the sample rate to 44.1 KHz.
8) Type the name SAVETEST.wav and click on the Export button.
9) Play back the resulting WAV file in QuickTime Player, Apple Loops Utility, etc. and it seems just fine.
What am I missing that you're doing?

Strange issue with USB mouse and USB headset.

Good day everyone.
I was experiencing a rather strange issue with my mouse and headset(both USB).
I am using KDE and ALSA, if that matters.
They are working just fine, but sometimes, when I try to lower\raise volume, my mouse derps out. I can move it around, but I can't click on anything(sometimes though, I can click on stuff in window that was active before and sometimes only on KDE panel) until I re-plug my headset. Then, nothing can use my headset until I reboot.
Anybody ever had that problem?

I've had similar problems for some time now. Unfortunately, I don't know what the issue is either, but perhaps we can come up with some setup similarities and narrow it down. I have similar trouble with just alsa or with pulseaudio, so that's not it. It is unrelated to the DE, as it happened for me in both gnome 2 and xfce 4. It is not related to the machine either, as the same quirks occur in other machines with the same headset. I have had inconclusive results with downgrading to kernel26-lts, the ancient kernel. I thought at some point it messed up and I was sure the older kernel didnt help, but after trying recently-ish, I had no trouble for days -- until I found that I didn't have trouble on the main kernel either. ... then a few days later, it showed up again. Very irritating!
https://bbs.archlinux.org/viewtopic.php?id=122475
Does my old thread sound like your issue somewhat?
Essentially, at times, if the headset (wireless) is changed into a different power state (unplugged/plugged) or the mic state is toggled (mute/unmute), things that could be clicked on normally cant unless theyre in the window already focused -- mostly.
What headset are you using? 32 or 64 bit arch? Have you tried downgrading to kernel26-lts?

I have like a paper gift card i got with a purchase and it has "gift card number" and "pin" and i want to redeem it but when i go to redeem a gift card on itunes it says "code" i i don't have that! please help i want to redeem this

i have like a paper gift card i got with a purchase and it has "gift card number" and "pin" and i want to redeem it but when i go to redeem a gift card on itunes it says "code" i i don't have that! please help i want to redeem this

coIt is a code. See:
iTunes Store: How to redeem a code
Apple - iTunes - Inside iTunes - How to Redeem Free Download Codes and Gift Cards In the App Store and iTunes

Strange behavior with Zoom and Image control

HELP - I have a strange behavior (bug?) with using Zoom
effect on an Image that has been placed on a Canvas. I am using
dynamically instantiated images which are placed on a canvas inside
a panel. I then assign a Zoom IN and Zoom Out behavior to the
image, triggered by ROLL_OVER and ROLL_OUT effect triggers. THE BUG
is that the image jumps around on the Zoom OUT and lands on a
random place on the canvas instead of coming back to the original
spot. This is especially true if the mouse goes in and out of the
image very quickly. HELP -- what am I doing wrong? Computer = Mac
OS X 10.4.9 Flex 2.0.1
Here's a simple demo of the bug -- be sure to move the mouse
in and out rapidly:
<?xml version="1.0" encoding="utf-8"?>
<mx:Application xmlns:mx="
http://www.adobe.com/2006/mxml"
layout="absolute" creationComplete="setUp();">
<mx:Script><![CDATA[
import mx.events.EffectEvent;
import mx.effects.Fade;
import mx.effects.Zoom;
import mx.rpc.events.ResultEvent;
import flash.display.Sprite;
import mx.core.UIComponent;
import mx.controls.Image;
private var zoomIn:Zoom;
private var zoomOut:Zoom;
private function setUp():void {
var image:Image = new Image();
image.id = "album_1_1";
image.x = 200;
image.y = 200;
image.width = 64;
image.height = 64;
image.source = "
http://s3.amazonaws.com/davidmccallie/album-128.jpg";
image.addEventListener(MouseEvent.ROLL_OVER, doZoom);
image.addEventListener(MouseEvent.ROLL_OUT, doZoom);
myCanvas.addChild(image);
zoomIn = new Zoom();
zoomIn.zoomHeightTo = 2.0;
zoomIn.zoomWidthTo = 2.0;
zoomIn.captureRollEvents = true;
zoomIn.suspendBackgroundProcessing = true;
zoomOut = new Zoom();
zoomOut.zoomHeightTo = 1.0;
zoomOut.zoomWidthTo = 1.0;
zoomOut.captureRollEvents = true;
zoomOut.suspendBackgroundProcessing = true;
private function doZoom(event:MouseEvent):void {
var image:Image = Image(event.currentTarget);
if (event.type == MouseEvent.ROLL_OVER) {
zoomIn.target = event.currentTarget;
zoomIn.play();
} else if (event.type == MouseEvent.ROLL_OUT) {
zoomOut.target = event.currentTarget;
zoomOut.play();
]]>
</mx:Script>
<mx:Panel width="100%" height="100%"
layout="absolute">
<mx:Canvas id="myCanvas" width="100%" height="100%">
</mx:Canvas>
</mx:Panel>
</mx:Application>

There must be bugs in the Zoom effect code -- I changed the
Zoom to Resize in the above code, and it works perfectly. Of
course, Resize is not as nice as Zoom because you can't set the
resize to be around the center of the image, but at least it works.
Does anyone know about bugs in the Zoom effect?

Strange Behavior with gMSA in Server 2012 R2

Greetings,
I have been doing some testing with gMSA Accounts in a Server 2012 R2 environment (two separate environments, actually), and I have noticed something very strange that occurred in both environments, which does not appear to be occurring in one of our customer's
self-managed environments.
We created a Group Managed Service Account using the following article:
http://blogs.technet.com/b/askpfeplat/archive/2012/12/17/windows-server-2012-group-managed-service-accounts.aspx
Everything went smoothly, and the account installs/tests successfully on both of the hosts that we are testing on. I am able to set my services to run under the account, and most of them appear to work fine. I am having some issues with a few of my services,
and I believe that the strange behavior I am seeing may have something to do with this - described below:
As soon as I set the service's Log On Account (via the Log On Tab under the Service's Properties), the entirety of the "Log On" tab changes to "greyed out," and I am unable to change the Log On account back via the GUI (Screenshot
attached).
I found that I am able to successfully change the account via Command Line using sc.exe, but the Log On tab remains greyed out! So far, I have found nothing to remedy this, but confirmed that it happens for any service I set to use the gMSA as the Logon
Account, and that it happens in 2 separate test environments, but not in a Customer's production environment - very strange.
All servers in this environment are running Server 2012 R2, and domain Functional Level is currently Server 2012.
I have been unable to find any information online about this behavior, so I am hoping someone has seen this before, and can explain why this is happening.
Nick

VIvian,
Yes, we used the Install-AdServiceAccount gMSA command on each host using the gMSA account, and then ran Test-AdServiceAccount gMSA, which returned "True."
However, one thing I noticed is that if I run Test-ADServiceAccount gMSA as a Local Administrator, it fails with the following:
PS C:\Users\Administrator> Test-AdServiceAccount gMSA$
Test-AdServiceAccount : The server has rejected the client credentials.
At line:1 char:1
+ Test-AdServiceAccount gMSA$
+ ~~~~~~~~~~~~~~~~~~~~~~~~~~~
    + CategoryInfo          : SecurityError: (:) [Test-ADServiceAccount], AuthenticationException
    + FullyQualifiedErrorId : ActiveDirectoryCmdlet:System.Security.Authentication.AuthenticationException,Microsoft.A
   ctiveDirectory.Management.Commands.TestADServiceAccount
If I run Test-ADServiceAccount gMSA as Domain Administrator, it returns true:
PS C:\Users\Administrator.<domainname>> Test-AdServiceAccount gMSA$
True
Is this normal?
Overall, I think the issue I am running into is at the Application Level, and not a problem with the gMSA, as it appears to be working. (Can Start/Stop services without any issues). I will be investigating my issue further with 3rd-party vendors, unless
you think there is something wrong with my gMSA accounts based on the information I have provided.
Nick

Strange behavior with NI 9401

Hi everyone!
I think I have a strange problem with the NI 9401 modules.
My hardware is a CompactRIO and I'm using Labview 8.0.
I'm reading a 13 bit encoder with two NI 9401 modules: the first for 8 input channels and the second for the other remaining 5. input channels.
13 bits means that the slots in the outest part of the counter are 8192 so i expect my encoder to count up/down till 8192. What instead happens is that the counter goes up to 7934, then suddenly to 7860, then from 0 to 254 and then finally to 0 again and up again to 7934 and the story always goes on like this. I put the true/false outputs of the encoder in a boolean array and then, from the boolean array to a number. (see the attacched VI)
Here's how I devided the inputs between the two modules
-NI 9401 2 :
DIO0= 2^0
DIO1= 2^1
DIO2= 2^2
DIO3= 2^3
DIO4= 2^4
DIO5= 2^5
DIO6= 2^6
DIO7= 2^7
- NI 9401
DIO0= 2^8
DIO1= 2^9
DIO2= 2^10
DIO3= 2^11
DIO4= 2^12
When running the VI I suddenly realized that every time all the input for each modules should be true ( i.e. five leds on for the second module or eight leds on for the first) , the value of all the inputs goes immediately to 0 i.e. all the leds switch off . To make an example: I see 4 leds on for the second module but when comes the time of the fifth, all the leds switch off so it means all the inputs are false which i can't understand. I tried to change the pin assignments in order to read the same inputs from different pins and this did'nt change anything. I tried to use only 4 inputs for the second module and this didn't work. Every time all the inputs for each module should be true it goes up to (n-1) inputs true and the n inputs zero. More information about this strange behaviour: while a normal false input produces a voltage of 0.036 V the voltage I measured from the last pin that should be true and that should give me all the leds on for one module, produces instead -0.146 V.
This is everything I tried in order to solve this problem but now I'm at a dead end.
Could it be a kind of module setting which I didn't consider?
Due to all the attempts I've made I excluded any disfunction of the encoder so I focused my attention to the modules.
Does anyone of you have any idea?
Thanks!!
Rob_F
Attachments:
Prova_encoder2.lvproj ‏14 KB
Prova_encoder2.vi ‏155 KB

Thanks a lot JMota!
We just sent back the encoder to the company who sells them. They want to be sure it's not a product defect or, even worse, a problem of conflict with the NI 9401.
In the meanwhile we built up the acquisition VI for the accelerometer and the encoder. One while loop sends the accelerometer data to a DMA FIFO and another parallel while loop is used to read the encoder outputs and send these data to another DMA FIFO. I did this because I know only 1 DMA FIFO can be used for each channel. When I read the data with two FIFO.read with two parallel loops in the Real-Time I discovered that I can't make them work indipendently as i thought i.e. reading settings of one FIFO.read ( number of elements and loop timing) affects also the other FIFO.read .
Any explanation for this behavior?
Thanks again JMota!

Strange behavior with Cisco AP and Intel 3945 wireles card

Similar Messages

Maybe you are looking for