Stuck in initial download in progress

I have swapped my upstairs and basement tv.  I never had problems before but haven't used the basement tv in several months.  It seems to be stuck in the" Starting up..one moment please initial download in progress ,it takes about a minute" except that it has been several hours.  Any suggestions?

The Initial Download in Progress screen appears to be the Interactive Media Guide (IMG) and its data being started and updated after an STB (Set Top Box) reset. But it should never take much more than a minute.
Did you swap your STBs or just the TVs? Was the box that is stuck working before the switch, or was it with the TV that has not been used in a while?
I would check all of your coaxial cable connections. Then I would reset the router. Then I would reset the STB. If you are using an HDMI connection to the TV, make sure that it is secure as well.
If the problem is still present, swap the STBs and see if the problem follows the box stays in the room. It could be a bad STB.
Find this post helpful, informative or just something you agree with? Click the red ‘thumbs-up’ button.
Did this post solve your problem? Click the green ‘Accept as Solution’ button.

Similar Messages

  • TS3694 hi i recently updated into ios 7.0.4 now i want to fully restore my ipad to resell but when i restore it it got stuck with apple logo and progress bar with 45% completed as firware file is downloaded using ipad 4 wifi itunes 11.3.8

    hi i rescently updated my ipad 4 in ios 7.0.4 and for resell purpose i want to restore my ipad via itunes but it got stuck at apple logo and progress bar of 45% completed i tried it 50 times but it stuck on that exact point for hours i cant able to restore it and had no errors it just like freezes at one point i also uses dfu mode but got stuck at same problem using windows 7 32 bits itunes 11.3.8 ipad 4 wifi please help

    My iPhone 5 wouldn't start after I turned it off a few minutes after writing this. It went into recovery mode and I had no choice but to connect to iTunes on PC and restore.
    I restored to factory setting first, just to validate my phone was okay. For a second consecutive iOS update, the  iPhone 5 did not update smoothly while connected to PC and iTunes - I had to retry two times before the progress bar for the update showed. (The exact same problem with the restart occured when I updated to 7.0.4.)
    The good news is that I was ultimately able to restore the iPhone 5 to factory settings while running iOS 7.0.6. I did have a backup from about a month ago lying around and was able to successfully restore with that as well, so the damage done is almost negligible since I had my contacts, notes, mail, etc. backed up to iCloud.
    Once I completed both restores, the sync with iTunes worked fine.

  • EM12 - Self-Update problem.  Stuck with 'download in progress' state..

    I just setup EM 12 and I'm having an issue with the self update. I attempted to download the linux 32bit agent in online mode. It ran for a few minutes than failed. The problem is self update thinks it's still in download progress even tho the job failed. I even deleted the job after it failed. It's still in "Download in progress.." state.
    So I decided to download the .sar file manually and to install it in offline mode using emcli. So when I use emcli import_update to install the .sar file I get "Entity already exists". Same resulsts even when using "-force". The entity actually doesn't exist, it was never downloaded.
    Any help is greatly appreciated!
    Thanks!
    Edited by: 928917 on Apr 19, 2012 12:54 PM

    Please log an SR from MOS and update this post with the SR number. I'll get this assigned to the appropriate team.
    Thanks
    Raghu

  • Stopped Initial download for Bupa_Main  in CRM in between

    Hi Experts,
    We have a problem in CRM. The initial download for the object BUPA_MAIN was accidently started by one of collegues.
    The job ran for almost 24 hour adn was still running. The queues went as high as to 40000 entries & the outbound queues started getting stuck in ISU system
    So we had to finally kill the job & things resumes as normal...
    Can anybody let me know as to what would be the impact of killing the job...

    Hi Rohit,
    Thanks for the info.
    Please let me know as to which table will i have to check to see if the download is successfully completed. ( for object BUPA_MAIN)
    And did u mean unlocking the queues by quoting 'clearing ' the queue. We we did clear the blocked queue (r3ad* ) but the queue R3AI* got cleared automatically...
    Also it seems that the R3AI* queue is still running even cancelling the job.
    Also shows as a error in SWMP tcode indicating a abort of initial download.  How do i get rid of it.

  • Installation - stuck on initializing

    Can't seem to get it to install, get as far as 'initializing installer' but progress bar just sticks there. Have tried restarting computer and trying again. Doesn't even let me cancel it, becomes non-responsive?

    Sorry you are having problems. Is this on mac or windows? Is it downloading from creative cloud correctly or is it not even getting that far? Are you using the latest version of the creative cloud app. It should be Version 1.7.1.418 released on 7/24/2014. Are you able to install other apps from the creative cloud app?
    Hopefully we can get you unstuck,
    Chris

  • When i open it gets stuck at "initializing installer" and the green bar doesnt move. How do i fix this so it installs?

    Adobe cloud setup downloaded off the internet just fine but when i open it gets stuck at "initializing installer" and the green bar doesnt move. How do i fix this so it installs?

    Multiredwolf123 have you utilized the steps listed in Error "Failed to Install" Creative Cloud Desktop application - http://helpx.adobe.com/creative-cloud/kb/failed-install-creative-cloud-desktop.html to resolve the current error?

  • Want to download Defauld Progress Bar from Oralce Site

    Hi,
    I am trying to download Defauld Progress Bar From Oracle Site, but it is showing message
    alt="Your browser understands the <APPLET> tag but isn't running the applet, for some reason." Your browser is completely ignoring the <APPLET> tag!
    Please suggest and how can I use that progress bar on my existing 6i form .
    thanks
    mohan

    then Applet will not work in any case....
    For 6i there is online help available for Progress bar
    To create a progress bar:
    1     In the Layout Editor, click the Text Item tool.  Drag to create a text item of the maximum size of the progress bar.  For a raised style bar, set the Bevel property of the item to raised.
    2     Click the Rectangle tool and create a rectangle slightly larger than the maximum size of the progress bar.  For a flood style bar, set the Bevel property of the rectangle to Lowered.
    3     Add trigger code to set the size of the progress bar as appropriate.  Change the size by programmatically adjusting the Width property.  Depending on your application you might do this within a PL/SQL loop, or in a WHEN-TIMER-EXPIRED trigger.  For example, use the Set_Item_Property built-in:
         DECLARE
       x NUMBER := Set_Item_Property(‘PROGRESS.PLAIN’, WIDTH);
    BEGIN
      if x <  120 then
        Set_Item_Property(‘PROGRESS.PLAIN’, WIDTH, x+5);
      else
        Delete_Timer(‘PROGRESS’);
      end if;
    END;
    Tip: Form Builder does not normally update the display while a trigger is executing.  To update the progress bar while a PL/SQL loop is executing, use the Synchronize built-in.
    To create the spinning wheel animation:
    1     Using a drawing tool such as Microsoft Paint, create an image file containing all of the different pictures, or frames, that you want to show for the animation.  To create a smooth animation, use at least four and preferably six frames. 
    2     In the Layout Editor, display the content canvas where you want the animation to be displayed. 
    3     Click the Stacked Canvas tool in the tool palette.  Click on the content canvas to create and position the stacked canvas.
    4     In the Property Palette, under the Physical node, set the Width and Height of the stacked canvas to the size of the image or larger, and set the Viewport X Position on Canvas and Viewport Y Position on Canvas to show the initial frame.  Under the Viewport node, set the Viewport Width and Viewport Height to the size of each frame. 
    5     In the Layout Editor, display the stacked canvas.  Choose FileImport to import the image file.  The image will appear in the upper left corner of the canvas.
         Tip:  If you have boilerplate images that you use frequently, such as a company logo, add them to your object library by dragging the boilerplate image object from the Canvas node in the Object Navigator and dropping it on the appropriate page of the object library.  To reuse a boilerplate image from an Object Library, simply drag it to the Object Navigator and drop it under the canvas where you want the image to appear.  This is faster and simpler than importing a file.  See the Gallery page in the DEMO20.OLB object library for an example.
    6     Add trigger code to show each frame as appropriate.  Depending on your application you might do this within a PL/SQL loop, or in a WHEN-TIMER-EXPIRED trigger.  Change the frame by programmatically adjusting the Viewport X Position on Canvas and Viewport Y Position on Canvas properties to position the viewport visible on the content canvas over the desired frame. 
    if responses are helpful or correct please mark it
    Baig,
    http://baigsorcl.blogspot.com

  • IOS7 Dictionary Trouble (stuck in mid-download?)

    I've noticed a few topics that sound similar to mine on the surface, but I seem to have an added layer of trouble going.
    I attempted to use the dictionary the other day while using Safari (highlight a word, select "define") and I got the "no definition found" screen. I realized that my dictionary(s) must be missing and I went to the "manage" screen to try to download them. Here's where things get weird:
    1) The Apple dictionary and New Oxford appear to be stuck in mid-download, showing an empty progress circle. (See image)
    2) I was able to download the Oxford British English dicitonary and I've been using that instead. It stays in my list consistently.
    3) I attempted to download the Japanese and Japanese/English dictionaries and they tend to work for a little while, then vanish, requiring me to redownload them.
    I'm kind of assuming the issue is at least partially caused by the two dictionaries at the top that appear to be caught in mid-download. Is there any way to reset those downloads/clear the cache? I've tried rebooting, turning airplane mode on/off, closing down apps that use the dictionary and rebooting again, etc. but nothing seems to change this.
    Would reseting network settings and restoring from backup do anything? Any other ideas?

    Glad you brought this up, I'm exhibiting the same exact issue but on my iPad 2. Both Apple and NOAD dictionaries are stuck where it wasn't before. I'm suspecting it's a bug. I'm actully thinking of nuking it with a fresh install.

  • ITunes installation always get stuck on "Initializing QuickTime types"

    Whenever i try to install iTunes and QuickTime it always get stuck on "Initializing QuickTime types."
    I am not able to update my software!
    Please Help!

    Me Too!!
    I have XP SP3. Intel pentium 4 2.6Ghz. 4Gb RAM. 116GB open on one HDD, 72GB open on the other.
    I'm on Admin access level.
    I'm trying to install iTunes 7.7 bundled with Quicktime 7.5.
    I emptied my temp folders.
    I shut down my antivirus and anti-spyware.
    I shut down all non-essential startup menu items.
    My folder names dont have unusual characters.
    I have uninstalled all versions of Quicktime and iTunes and iPod updaters from my machine.
    Still no luck.
    When Installing the Quicktime application, the entire machine locks up when it gets to the "Initializing Quicktime types" segment of the install.
    I have left the machine on its own for up to 14 hrs and it never does regain normal function.
    The only way to regain control is to reset or hard shutdown.
    Can someone please respond to this so my daughter can use her 2 month old graduation present?
    Thank you so very much.
    PS:
    How about standalone downloads for each application?
    And, how about patches so the download doesnt take so long and the installation doesn't need to be so intrusive?
    Message was edited by: Jeteye97

  • It is stuck on Initializing Installer???

    I am on PC and when I double click the icon to install I the green bar moves a little but stops after about 20 seconds and it is stuck on initializing installer. Tried restarting and re downloading nothing helped.

    Hi Poke,
    Please refer to the help document below to fix the error:
    Error: "Installer failed to initialize" | Windows
    You may also refer to the threads below where this issue has been addressed:
    Creative Cloud Installer not Initializing AGAIN.
    Installation - stuck on initializing
    Re: App Installer Freezes at "Initializing Installer"
    Regards,
    Sheena

  • Updater stuck on "initializing", iTunes wont recognize Ipod anymore

    Hi,
    Just got a new Ipod over a week ago, uploaded all my songs and everything seemed to be fine...until today - i've recharged it on my laptop and tried turning it on but it didn't work - went on the support site and finally restored the iPod to Factory Settings. When I connected my iPod again to the Laptop, iTunes didn't recognize my iPod. So I've downloaded the latest iTunes and tried updating the software.
    Now, when i try to update with the iPod Updater 2006-03-23, it gets stuck on "initializing" and iTunes won't recognize my iPod either.
    When I click on My Computer, it comes up as "Removable Disk E" and in Device Manager, it comes up under Disk Drives "Apple iPod USB Device"
    When i switch on my iPod, it seems to be working fine...but i just cannot download any music on it coz my iTunes won't recognize it...
    Please help!!!!
    I use Windows XP, Dell Inspiron 630m and iPod 30GB
    Thanks,
    Cornelia
    Dell Inspiron 630m   Windows XP  

    thanks, i'd appreciate that...
    i went to the ipod store today and have been told that my ipod is fine but my software causes the issues. I'm supposed to delete everything and restore again. Trying to do that now but it's still not working yet. I had Tunebite installed to convert wma to mp3s as well, that might have caused all the trouble. there might probably still some hidden files i didnt get rid of because when i reinstall iTunes, my iPod is still not recognized... i keep u posted as well...

  • Problem with initial download of a data object

    Dear All,
    I have created a data object named "EQUIPMENT", which has three nodes. EQUIPMENT is the header node, DETAILS is the child node to EQUIPMENT and LOCATION is the child node to DETAILS. I have also done explicit key mapping to DETAILS and LOCATION.
    I have selected the following as the BE Keys in the nodes.
    SERIAL NO in EQUIPMENT header node.
    TYPE in DETAILS node.
    ZIPCODE in LOCATION node.
    In the explicit key mapping of DETAILS node we have selected "SERIAL NO" field in this node.
    In the explicit key mapping of LOCATION node we have selected "SERIAL NO" and "TYPE" fields in this node.
    Data object contains no errors and i have activated the data object and it was successful.
    Then i have also created back adapter which has EQUIPMENT get list and get detail. Get list returns only serial numbers (which is the BE key in EQUIPMENT node). Get detail takes "serail no" as input, returns "DETAILS" and "LOCATION" data in tables parameter. I have tested the get list and get detail interfaces, they are working fine. Then i have activated back end adapter and that was successful.
    Now i have triggered an initial download for the  "EQUIPMENT" data object, but there is no data downloaded into the data object. I have checked the monitoring in administration portal, it is showing status "Ended with errors", but there is no details of an error.
    So can you please let me know what could be mistake i have done or how to check what is the error. Please help us to resolve the issue.
    Regards,
    Kiran.

    Hi Kiran
    Are you checking in the NWMA>>Monitoring>>Logs and Traces>>Backend Integration?  The logs should have the proper error.
    If not can you regenerate the DO, edit and activate your adapter and try again?
    Regards
    Rohith

  • Color Laserjet Pro MFP M177fw - stuck on initializing - fresh new printer not working

    http://h30434.www3.hp.com/t5/Printer-All-in-One-Install-Setup/Pro-MFP-M177fw-stuck-on-initializing/m-p/5097731/highlight/false#M194928 ==QTE==Two days ago I received my printer (same as in this thread) and I am experiencing the exact same problems which are described throughout this thread. The printer is stuck on initializing and makes continuous loud noises. Please let me know how this can be taken care of. I would either need to replace this product, or to have it fixed somehow. Await yours soonest.==UNQTE== ++ Ref to the question from the above thread, I also post it here as  a new question just to ensure that I get a response. Thanks beforehand and look forward to hearing from you. BrgdsErik

    Hi @SSAB ,
    I can send you that information in a private message.
    In the forum beside your handle name just click on the envelope to view it.
    What happened prior to this issue? (update, paper jam, changed toner)
    I would do a hard reset if you haven't tried this method.
    Leave the printer on and unplug the power cable from the printer and wall outlet for 60 seconds.
    Then reconnect the power cable to the printer and wall outlet rather than a surge protector.
    This ensures the printer is receiving full power and may help this situation.
    If you need further assistance, just let me know.
    Have a nice day!
    Thank You.
    Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
    Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
    Gemini02
    I work on behalf of HP

  • Problem with initial download from R/3 to CRM

    Hello All,
    Initial we were able to download & replicate all object from CRM to R/3  & vice versa such as product ,BP, sales documents & conditions etc. After that <<removed>> R/3 system was refreshed by Client itself. After refresh, connectivity between R/3 & CRM is disturbed.We have observed that while initial download we are facing problem in SMQ1 & SMQ2. After debugging we found that table entry  i.e. table :- CRMMLSGUID from CRM & CRMPRLS from R/3 have Logical system guid values different( which  should be identical). Because of this no replication is happening between CRM & R/3. How to rectify this?
    Regards
    Priyanka
    Edited by: Rob Burbank on Dec 9, 2011 4:37 PM

    Hello,
    see note 588701:
    "The queues are deliberately halted since the change of the logical       
    system name in the R/3 backend or the linking of new R/3 backend clients 
    to a client of the EBP/CRM Server with the same logical system name as a 
    client already linked to the R/3 backend would lead to severe data       
    inconsistencies in various CRM applications.                             
    For this reason, such changes are not allowed on principle. The halting  
    of the queues prevents such data inconsistencies. The following          
    situations may lead to the queues being halted:                                                                               
    o  The logical system of a client of an R/3 Backend system linked to 
           the EBP/CRM server was changed in current operation.                                                                               
    o  A new client of an R/3 Backend system or a client of a new R/3    
           Backend system was linked to an existing client of the EBP/CRM    
           server where the logical system name was already assigned to a    
           client of an R/3 Backend system linked to the CRM server before.  
    There are different cases in which different forms of processing are      
    required or where several options exist:                                                                               
    -  The logical system name of an R/3 Backend client was changed    
              in current operation. In this case, the data hangs in the       
              outbound queues of the R/3 Backend system as specified under    
              point 1 of the symptom. In this case, the logical system name   
                                                                     Seite 2                                                                               
    must be changed back to the original value. Then the outbound   
              queues can be reactivated. If no data was transferred to the    
              EBP/CRM server before the change, also a correctioin of the     
              check table is possible.                                                                               
    -  The same logical system name was used again in a new client of  
              an R/3 Backend system that was linked to the EBP/CRM server.    
              In this case, the data is in the inbound queue of the EBP/CRM   
              server with the exception GUID_FOR_LOGSYS_CHANGED. In this      
              case, the queue entries which have status SYSFAIL must be       
              rejected, however, not the entire queues. If the new client of  
              the R/3 Backend system you have linked has exactly the same     
              data as the old client and if it is meant to replace the old    
              client (that is, this was deactivated), also a correction of    
              the check tables is possible. In this case, the inbound queues  
              can be reactivated after the correction.                        
    The correction of the corresponding check tables or the correct           
    procecure in individual cases is to be agreed upon with the support of    
    SAP or SAP consultants at the customer site. In justified cases, SAP can  
    carry out the correction of the check tables.           "

  • Initial download of Z contract table from R/3 to CRM

    Hi,
    We have two contract tables called ZCONTRACTHEAD and ZCONTRACTITEM in our R/3 system which we bring to our CRM system to the same respective tables.
    We use a downloadable object ZZCONN_HEAD and ZZCONN_ITEM in transaction r3ac1 and do an initial download using r3as.
    My problem is that in CRD client 200 which is mapped to R/3 client 200, this download does not bring any data into CRM. The download says complete but I get a BDOC error in SMW01 saying validation error.
    This download works perfectly fine in CRD client 100 which is mapped to R/3 client 600.
    I know that this is custom table and not a SAP standard table. But I really don't understand why this would work in one client and not in the other client. I have checked the RFC destinations and also did some other initial downloads on CRD 200 which works fine except for this particular table.
    Could you please give me your opinion on how can I debug this and find where is the problem? After doing few debugging myself I found out that I am getting the validation error in BDOC in CRD client 200 is because the intitial download is not bringing any record from R/3.
    Due to this problem our contract pricing is not working on our DEV system and I am not able to do any further tests or enhancements.
    Any suggestion or insight on this will be very helpful.
    Thanks,
    Prasoon

    Hi Michael,
    Thanks for your reply. I tried to debug the initial trasfer from CRM to R/3 but I am not able to debug the function in R/3. Also when I do a Test Function module in R/3 I am not sure as what correct parameter to put. I did refer few OSS notes 656823and 573857 but was not able to debug it in R/3. We are on CRM 3.0 Service Pack 14. Could you please suggest as to how can I debug this initial download ?
    Since this initial load works perfectly fine in the other client(100) and not in in client 200, I am not sure what could be the problem.
    Any suggestions will be appreciated.
    Thanks,
    Prasoon

Maybe you are looking for