Swap PC Card Slot on T61P?

When I ordered my T61p I made the mistake of ordering the wrong option for the PC Card Slot. I accidentally ordered the Smart Card Slot instead of the Media Card Slot.
1. Is this swappable by me?
2. If yes, does anyone know the part # for the Media Card Slot and/or is it multiple parts?
I got a PCI-e 3G Card and I can't use it until I remedy this.
If a Lenovo Moderator knows the answer or anyone else in this forum I sure would be grateful for the help!
Cheers,
JIM

If you go to this Lenovo webpage, download your 14.1" or 15.4" Hardware Maintenance Manual.
In there you should find the proper part number.

Similar Messages

Swap Express Card/34 slot for SD Reader

Is there a way to swap the Express Card Slot for an SD card slot, like the current MacBooks have?

Short answer, no. Get a SD ExpressCard Adapter.
Dave M.
MacOSG Founder/Ambassador  An Apple User Group  iTunes: MacOSG Podcast
Macsimum News Associate Editor  Creator of 'Mac611 - Mobile Mac Support'

USB ports and memory card slots not working

My Pavilion a6120n desktop has worked brilliantly ever since I purchased it. As of last week the 2 usb ports in the front and the 2 unused usb ports in the back have stopped working. My printer is plugged into one rear port and my wireless mouse is plugged into a second rear port and these work fine. I generally use a memory stick for data swapping or the card reader slots (which have also stopped working). I no longer see the memory card icons in the "Computer" window. When installing something new the "New Hardware Found" statement pops up but the driver install always fails. I think it is a software issue but there are no usb drivers to download on the HP/support site that I can find. . . so . . . Below is what I have tried so far.Run antivirus software. Full scan & memory scan - no issuesRun malewarebytes full scan - no issues I have tried restarting several times with no success. Restore to several previous restore points = failedRestarting computer in repair mode = failedRun the repair disk that I had made = failedChecked the power management for each usb port to see if the power was routed properly = okRemoved the case cover and carefully inspected the wiring and connectors.finally I tried uninstalling the usb drivers = failed Upon restarting the computer the last time the startup file must have failed and after several hours of attempting a repair I had to reinstall the Window 7 completely. Still no usb or memory card function. Any help would be appreciated Thanks,MrBob38

Hello , Welcome to the HP Forums, I hope you enjoy your experience! To help you get the most out of the HP Forums I would like to direct your attention to the HP Forums Guide First Time Here? Learn How to Post and More. I have read your post on how the USB ports and memory card slots are not working, and I would be happy to assist you in this matter! Since you mentioned that you have already re-installed Windows 7 on your computer, and the USB ports still do not work, please contact our technical support for further assistance in this matter by clicking the link below to get the support number for your region.
www.hp.com/contacthp/
I hope this helps!
Regards

PC Card slot unusable after ejecting device

I use my TiBook's PC Card slot for a Linksys wireless G card, and a SanDisk compact flash card reader. For the past few days, OS X only recognizes the device that is in place when the system is started (cold start or restart). When I eject the device and swap in the other one, or even put the initial device back in, it is not usable. The PC Card menu icon appears, and clicking on it shows that the device is being properly identified (Broadcom 802.11 or SanDisk blah blah depending on the device) but OS X won't let me use it. In the case of the wireless card, Internet Connect says "no airport hardware detected". In the case of the compact flash card, it doesn't mount or show up in Disk Utility.
Any advice?
TiBook 867 Mac OS X (10.4.7)

Claudio Lis wrote:
Hi All,
I have a Powerbook Titanium G4 1GHz and an Adaptec AUA-1420a USB 2.0 2 Port CardBus. This card worked fine until Leopard instalation, I made all my backup in a external USB drive before start the Leopard setup.
Now, when I connect the card on PC Card slot, nothing happen. I tryed a Encore Ethernet Adapter and had the same status. In logs (system.log, or others in /var/log) nothing about, no errors, no warnings, no info, PC Card Slot is completly dead.
I tryed reinstall Tiger and Panther in other partition, because this card used work in those version, but, now CardBus doesn´t work anymore.
I tryed this card in another Powerbook G4 Aluminium running 10.4.11, and it works fine and system.log shows when it are connect or disconnect.
Can anyone help me?
Thanks!
Welcome to the Apple Boards:
Two things:
First, click on the little apple logo, top left whilst holding down the Option key and select System Profiler.
Check the POST diagnostic and also the other hardware. See if anything shows up
Secondly, zap our PRAM and see if that helps.

Card slot does not work after update (14/10/2011)

Card slot does not work after yesterday update (14/10/2011)! It works with my SD card month ago, but now it dosn't!!!
MacBook Pro 13 OS ver. 10.6.8

Thanks for your suggestion. I downloaded OnyX and ran the cleaning function. After restarting, I opened Help and once again the first screen appeared fine. But again most of the links did not work, though those under the "What's New" heading did work. I might add that I had previously tried a variety of suggestions posted in another thread, which included deleting from the caches folder in Home>Library several files such as com.apple.helpui and help.plist in the Preferences folder. (As noted in my previous post this evening, I also created another user but that also did not have any effect.) Any other ideas? Thanks

Hi, I have a Lenovo 3000 n100 that does not recognize the dvd player or SD memory card slot

Hi, this is my first time on here so forgive me if I don't give all of the right information, I will try. Until about a month ago my dvd player and SD memory card slot worked fine. I was attempting to download pictures from the SD memory card to my laptop when for some reason it not only stopped reading the memory card but it erased it also. I tried to watch a movie on it to see if it was working and it is not. I checked the computer to see if I could manually turn it on and neither the memory card slot or the dvd player show up at all. Is this a driver problem and if so how do I fix it. Any help would be greatly appreciated. Thanks, Linda

I have struggled with the same thing, until about 1/2 hour ago....And its real simple. I'm not a techy but here's what worked for me.
Since Lenovo doesn't send boot discs you are going to have to create one. I went to http://www.ntfs.com/boot-disk.htm and downloaded the trial version - good for 10 days. If this works for you then you should buy the software (that goes w/o saying).
Once loaded to your machine you will need to create a DVD (CD may work as well, all I had was DVD's handy). Just lauch the application and it will do this for you.
Then you need to insert the DVD/CD into your player and restart the machine.
Once lauched the Software will lauch the Active@ Boot Disk menu. One of the options (going from memory here) was to give you a windows prompt. I simply typed c: and took me to the C drive. Then I typed chkdsk /f c:
I was then told my c drive was locked (sounds familiar I bet) but this time I was given the option to dismount the volume which I did. And it finally ran chkdsk, found and corrected all errors.
I rebooted my machine, launched diskeeper, and guess what - I can finally defrag my harddrive now which is sorely overdue!
Good luck. I hope this works for you!

Memory speed and graphic card slot

Hi,
I have just built a system with a P67A-GD65 B3 board, everything works fine, but while double-checking on the system's specs and performances I came across two weird issues:
- I have 2 x G-Skill F3-17000CL7-2GBXHD RAM sticks at 2133MHz, I have enabled XMP in the BIOS (with leaving all other settings in automatic mode) and the BIOS indicates the RAM is running at 2133MHz, 7-10-7-27, however, when I run the MSI Control Center (latest version of the app) it says on the home screen of this app that my RAM is detected as "DDR3-1600 (800MHz)" in the speed field. I also ran CPU-Z and it says there that my DRAM frequency is 1064.4 MHz (the FSB:DRAM value is "1:8"), with the 7-10-7-27 timings values. Which one should I believe? The WEI gives a score of 7.9 for my memory which is ok, and I am not running in any performance issue nor I am looking to do any overclocking, but I just want to make sure that I am making the best out of my money and that I am using the RAM as it is supposed to be used... Can someone shed some light here?
- I have installed my graphic car on the slot that is the furthest possible from the CPU as I believe they both generate quite some heat and so they should be as far away as possible from eachother. In CPU-Z I have a link width for the graphic interface of "x8" with max supported of "x16". Is this something that is related to the slot and should I move the card to the slot closer to the CPU? Or is this something else? Is there a setting in the BIOS maybe that can address this?
Thanks!

Both are correct information. The detected '1600MHz' is actually the factory stock speed from the IC chip of the RAMs. The readings of "1064.4MHz" is the running speed that the RAM is currently on so for DDR calculation, you have to multiple 1064.4MHz by 2 to get 2133MHz.
The reasons for 2 readings to be detected is due to your RAM being factory overclocked by manufacturer before it went on the retail shelves, which is very common. Most or any RAMs that you see with speed above 1600MHz are generally overclocked by manufacturer using 1600MHz RAMs for speed boost.
The graphics card slot will still runs at x16 with your card.

Problem with memory card slot on nokia c5 03

Sir,
I have a Nokia C5 03 from the last 8 months.....
Working very well.
Recently, my memory card stopped working.
I thought that there might be a problem in the memory card and bought a new one.
Even though i inserted new card in my phone, i am getting the same error.
In file manager it is displaying as "Memory card Corrupted."
I have checked the new memory card by inserting in to another phone which was working normally.
There i have even formatted the new memory card and again inserted into my c5.
Then also i am getting the same error message........
Can any one suggest me what to do in this regard??????
Thanks in ADVANCE.
Solved!
Go to Solution.

Hi,
Welcome to the forum!
Have you also tried inserting the old memory card to another phone as well? What happened after inserting it to another phone? If it's working properly with another phone, the memory card slot of the C5-03 might have an issue so you should bring it to the repair facility to have it checked.
You can search for the nearest repair facility in your area from this link: http://www.nokia.com/in-en/care-point-finder/
Hope this helps.

I have a iPhone 4 which was on Verizon. I now want to start using it on Walmart Family Mobile. I know I have to get it jail broke but people are telling me that I can't use it as it has no sim card slot. Is there a way of getting around this problem?

How can I use a iPhone 4 without the sim card slot on Walmart family mobile?

The Verizon iPhone 4 is a CDMA only phone. It is not physically possible to use it on a GSM network. It doesn't have the right parts. Also, we can't discuss jailbreaking here.
Best of luck.

Looking for an inexpensive all in one HP printer that has an SD card slot. Any suggestions

Looking for an inexpensive all in one HP printer that has an SD card slot. Any suggestions

ChrisPbass,
I would suggest contacting HP Home & Home Office. They will be able to narrow down the field to what would be best for your particular use. There number is below.
1 (888) 999-4747.
↙-----------How do I give Kudos?| How do I mark a post as Solved? ----------------↓

What is use of sim card slot in hp pavilion dv4

i want to know how to use sim card slot in my HP Pavilion dv4 laptop

Hi,
It's a SIM card slot and it's for a SIM card. But to be able to fully utilize/utilise it you also need a WWAN card. What is the model of your machine ? dv4 is a series of many model, most of them do not have WWAN cards built-in.
Regards.
BH
**Click the KUDOS thumb up on the left to say 'Thanks'**
Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.

H430: Windows 8.1 is not recognizing SD card slot

I have Lenovo H430 and is working great for me.... yet i have a problem after upgraded windows from8 to 8.1
the SD card slot is not recognizable
can't be found in device manager
and when i try to add the device it is not found, so what i do is run the .exe and that is all
1st nothing happen when i insert the SD card (it is 8GB)
so i downloaded the device driver and now whenever i insert the SD card nothing happens more than turning the green light on!!
still not recognizable

@Sarahmarie
You can try out this process and see if it helps:
Troubleshooting Audio Problems with External Speakers, Headphones, and HDMI Sound Devices
I assume that you probably already have seen this, but for your convenience, here is the support page for your notebook: HP 15-r029wm Notebook PC Drivers
The newest audio driver I could find there for your notebook has these parameters:
Released: 2014-02-21
Version 6.0.1.7156
Realtek High-Definition (HD) Audio Driver
The version number matches the one you gave but the date is different.
You can always try the Realtek site, for their drivers, however, they are not going to be customized to match the components in your notebook, but you could try and then go back if it does not help.
Realtek Downloads
Another thing you can look at from the Microsoft support website:
Automatically diagnose and fix Windows audio playback problems
Malygris1
I work on behalf of HP
Please click Accept as Solution if you feel my post solved your issue, it will help others find the solution.
Click Kudos Thumbs Up on the right to say “Thanks” for helping!

I have a MacBook Pro 13inch 2.4GHz (Intel Core 2 Duo, 4Gb RAM, 250Gb HDD, NVIDIA GeForce 320M graphics, SD card slot, up to 10 hour battery life)bought in October 2010 in the UK. The charger has stopped working. Which model and voltage do I need please?

I have a MacBook Pro 13inch 2.4GHz (Intel Core 2 Duo, 4Gb RAM, 250Gb HDD, NVIDIA GeForce 320M graphics, SD card slot, up to 10 hour battery life) bought in October 2010. The charger has been playing up for a while now - the light going out but coming back on when I move the cable a bit - faulty connection it seems. It has now stopped working at all.
Apple UK charge a whopping £65 for a replacement - and the reviews are AWFUL for it!
I need to know which one I need - 45w, 60w and 80w are listed - can someone tell me please? If I'm going to pay this price I want to make sure I get the right one!
Also, is a genuine Apple one available on Amazon UK, does anyone know please?
Any help will be much appreciated.
Meanwhile my battery is going down.....

Thanks for that wjosten. Much appreciated.
I've read here on Apple's site that the 85W version will work, as you say, and that it would run cooler with a 13" Macbook - I have a 13" MBP of course but assume this would be the same with mine. I wonder if running cooler is a good thing (it sounds as if it is) and it would be better for me to get the 85W version than the 60W one?
Then I have to decide whether to pay the (extortionate as it seems to me, though I may be wrong) £65 from Apple (bearing in mind the rotten reviews here of the Apple product), or risk a cheaper alternative from Amazon UK, at around £20 (also with various rotten reviews)... Any suggestions? Please? :-)

I bought an iphone sprint carrier on ebay but i want to know if the phone is going to work for an international carrier movistar which is gsm due to the phone does have a sim card slot , what do i need to do ?

help me how can i get my phone to work in movistar which is my carrier in ecuador gsm . sprint iphones does have sim card slot but i'm not sure if it will work for gsm what do i need to do , how do i unlock it

IF the phone was unlocked by Sprint for international use, it will work on any compatible (non U.S.) GSM carrier.
If it was NOT unlocked before you acquired it, you will need to move to the US and establish service with Sprint, then wait the minimum amount of time specified by their policy before they will agree to unlock it for you.
If you are not a Sprint customer, you bought the wrong phone.

I can not open the microsim card slot and my ipad is brand new!

When i try to opne the microsim card slot to introduce the sim card nothing happpens. Can somebody tell where and how I introduce the microsim card in my ipad?

The trick is pushing the SIM eject tool in a 45 degree angle as was also the case with the iPad 2, as opposed to the iPad 1 (and all iPhones). Pushing it in a 90 degree angle won't open the tray, unlike in the listed models.
Also see the photo and description at http://support.apple.com/kb/HT4577 , which also shows this.

Swap PC Card Slot on T61P?

Similar Messages

Maybe you are looking for