SX 60 HS There is a flashing red camera icon
There is a flashing red camera icon after I press the shutter button halfway. I can't seem to find out what that means. I searched the user manual,. Perhaps, I am just missing it or calling it the wrong thing. Or perhaps it is so obvious that it doesn't need to be called out specifically.
Any help would be appreciated.
Solved!
Go to Solution.
Hi Scoles15,
That flashing camera icon is an indicator for camera shake and that you should probably use a tripod or flash since the shutter speed is most likely very slow. Page 175 of the user manual provides the following information to deal with the issue:
I hope that helps you!
Steve M.
Similar Messages
-
Large outside Junction/Control box has flashing red light - bad or normal?
There is a Verizon outside box that is large with a flashing red light on its side. It appears to be a junction or control box mounted on the ground. It has been there for years and I do not remember seeing a flashing red light until now. Plus, my DSL connection has been dropping recently. Can a tech rep from Verizon High Speed Internet answer? Thank you for yur patience.
Solved!
Go to Solution.These boxes are called Remote Terminals, and yes it is for DSL. The flashing light probably means that the battery backup has failed, so it shouldn't really affect your DSL unless your power goes out. And even then, the battery backup is only to power the voice line to make calls.
I would call 1-800-VERIZON and choose the option about "repair." I've had luck with getting poles replaced/repaired that way. Say that there's a flashing red light on the remote terminal, give the street address, and also give the central office you're out of (IE, your area code and first 3 digits of your phone number should tell the rep where you are). Also, stop by it and see if you can find any writing/markings on that, and tell them that too. Be as specific as possible. Make sure you get a ticket number from them, and make sure they have a call back number.
There was a tree laying on a wire near me, and I made sure I got a repair ticket; the next day a tech called me to say he was headed out that way and asked specific details about the location, what was wrong, etc. A few days later the tree was gone. -
I have a problem where there is a flashing red clip emblem in the middle of the frame for about two minutes at the start on a dvd. The clip is about 40 minutes total and I need to see if I can take this flashing emblem out. Since it is burned to the dvd and it is mpeg 2 is there anyway to take it out using final cut pro or some other program? I also have CatDV pro. Any ideas would be appreciated.
MarkI assume this red emblem is over a live background, right?
If you were to try retouching this in Photoshop or even a proper rotoscoping application, that's around 3600 frames for two minutes. Multiply that by how many minutes you need for a single frame and factor in your hourly rate...
Not saying it can't be done, but who is going to pay for it and how much is your sanity worth? -
Ipod flashes red when attempting to sync.
since 5.0 i have not been able to sync and i have lost 1200 songs from my ipod that are still showing in my itunes library. when i attempt a transfer the ipod icon in the margin of itunes flashes red then i get unknown error -69.
A) what does the flashing red ipod icon indicate?
B) to what does error -69 pertain?
3) would resetting my ipod and erasing everything solve the problem?
P.S. i just purchased an ipod mini for my wife and have been able to put songs on it from my itunes using the same cable that i use for my 40gb ipod.Its not your ipod it's a smorgasbord of probolems everyons been having with itunes 5. Wait till they get a patch for it. I have a probolem windows or itunes shutdown and dont recognise my pod when plugged in!
-
Flashing red Light on Photosmart D5160
I have a 3-4 year old Photosmart which know suddenly comes with flashing red light when i try to print.
In the display it says ERR and there are two commas or something on the bottom right. It does not match any of the problems which i can find on hp's pages.
I received an error message on my computer when trying to print - saying something like : do not recognize usb (code 043) Port_#003 Hub_#0003.
Can anyone help me out?
espenHi,
Flashing amber LED does not always point to fault. Please see this bug related to system
LED flashing amber.
CSCsh44884 Bug Details : Appliance: No Troubleshooting for System health LED
Status: NEW
Symptom: The appliance hardware has a "System health LED" that may go into amber status,
to indicate a hardware warning, and red to indicate a hardware failure.
Conditions:
In most situation the ACS appliance is still operative, when the light is in amber status.
The appliance should offer better information on what condition caused this alarm, and include this either by new CLI command, or included as additional information in pakage.cab file.
.Workaround:
-Reload appliance
-Verify enviromental conditions (temperature, power)
Alternate Details:
Symptom:
The appliance hardware has a "System health LED" that may go into amber status, to
indicate a hardware warning, and red to indicate a hardware failure
http://tools.cisco.com/Support/BugToolKit/search/getBugDetails.do?method=fetchBugDetails&b
ugId=CSCsh44884
Let me know if you have any question.
Regards,
~JG
Do rate helpful posts -
My z10 led flashing red when charging and even at battery full it blinks red. no green at any notification. But at below 10% charging level it blinks with a combination of red and green. Please send me any settings to be changed if.. at full charged no green light is blinking.. how many colours does z10 led have..and when it works and how to make those settings..or was my led not working fine? I am worried so much..plz help me
Your LED is fine, on the Z10 there is not "network signal available" green LED, as you're accustomed to from the legacy devices. At reaching 10%, the LED will blink orange.
Red for message or applicaiton notifications.
if you want to edit and create specific LED color combination, see the third party apps such as BeBuzz or Hub++
1. If any post helps you please click the below the post(s) that helped you.
2. Please resolve your thread by marking the post "Solution?" which solved it for you!
3. Install free BlackBerry Protect today for backups of contacts and data.
4. Guide to Unlocking your BlackBerry & Unlock Codes
Join our BBM Channels (Beta)
BlackBerry Support Forums Channel
PIN: C0001B7B4 Display/Scan Bar Code
Knowledge Base Updates
PIN: C0005A9AA Display/Scan Bar Code -
Why is my network extender flashing red and pink?
hi,
I have had my Verizon extender for a while, I bought a new Motorola modem/router connected them up and now my network extender isn't blue like it was before.
the system band is flashing red and the gps band is solid pink.
I have unplugged it more than once and it still won't go back to blue!
Any help please?
thanks
KarenThe breakpoint may not be as expected..
OPen the subVI and check to see if there is a red contour when it is not running.
If it is the case, use the brakepoint (pointer) and click onto a blank area inside the block diagram of the subVI. The red contour should dissappear.
Run the vi (main vi). See if it is okay. -
Blackberry LED light keeps flashing red
Yesterday Vodacom Care gave me a new Q5 device - i had a Q5 for 2 months and the phone just went dead - so they replaced it . Now my Q5 LED light keeps flashing red and it's a NEW PHONE ??? - make it stop please !
Hello,
Welcome to the BlackBerry Support Community Forums.
Thanks for the question.
Follow the steps below to try and bring the BlackBerry Q5 back to life:
Ensure that BlackBerry Link is installed on the PC or Mac OS
Ensure the computer has an internet connection.
Launch the BlackBerry Link Software.
Note: A backup of the BlackBerry device should be tried before a reload.
Turn off the BlackBerry device. Make sure there are no flashing LEDs and that the LCD is not still being lit by the backlight. If there are any flashing LEDs, hold the power button for 15 seconds until the LEDs stop.
Connect the BlackBerry device to the computer.
When prompted with Cannot communicate with device, click Restore and then click yes allow the update to be downloaded and installed on the BlackBerry device.
If the restore button is not seen press the vertical dots in the lower right corner of BlackBerry Link and select disconnected device. Highlight the disconnected device you are working with and attempt steps 4 to 6 again.
If the issue still persists, then I suggest contacting your network service provider for repair options.
Let me know if you have any more questions.
Cheers.
VIA | ViciousFerret
http://supportforums.blackberry.com/t5/BlackBerry-Z10/BB-Z10-Died/m-p/2230087#M10125
Please thank those who help you by clicking the button.
If your issue has been solved, please resolve it by marking "Accept as Solution" -
I bought this last year - early summer. It worked great at first.
Sometime during the winter it stopped working with a constantly flashing red Sys light. I have tried many times to start it up, same issue even when leaving it powered up for hours. What is my next step in trouble shooting this issue?Call Verizon Wireless Customer Service at (800) 922-0204 and verify the device is registered and working properly from there end. Good luck!
-
Put Home Hub 5 in another socket - flashing red
Hello
Before we moved into our home, the upstais office was used as the main socket for the BT infinity which the previous occupants had. This socket is the MK 1 socket I believe.
When we moved in, the BT engineer fiddled around and put one of the dual MK 2 sockets in the kitchen and put the home hub into that one. I have now decided to move the hub upstairs the older socket, but as you can guess, it won't work.
There is a dial tone and the phones in this socket work fine, but the home hub 5 has a steady orange light and the little broadband light is flashing red, indicating no broadband.
As someone who knows little about the workings of telecomunications in a home, I really would appreciate some advice on what the problem is, and how to solve...Other occupants will be connected using wireless, or broadband extenders.
The home hub is in the best place, to ensure you get the best connection speed. I would not attempt to change anything, and it would cost you £130 if you called an Openreach Technician in to change things, as the way its been installed, is the correct way.
You could end up with a very unreliable broadband connection, as the extension wiring would interfere with the signal.
If the wireless signal upstairs is not strong enough. Then there are some solutions on this page.
http://www.shop.bt.com/mini-sites/bt-connected-home/home/
There are some useful help pages here, for BT Broadband customers only, on my personal website.
BT Broadband customers - help with broadband, WiFi, networking, e-mail and phones. -
While updating to iOS, it appeared that the download was progressing so I laid my phone down. Checked about a half hour later and I now have a continuously flashing red screen that alternates with the Apple screen. I can't power the device off nor use the home button. iTunes doesn't recognize the phone so can't sync or reload.
Hello rwax,
The troulbeshooting steps detailed below can help get your iPhone to successfully power on.
If a single application is not responding or stops responding when it opens, you can force it to close.
If the device is unresponsive or if certain controls aren't working as expected, restart your device.
If the device remains unresponsive or does not turn on (or power on), reset your device.
If there is no video or if the screen remains black, verify that the device has enough charge to turn on:
If you are using an iPad, ensure that it's connected to the USB Power Adapter supplied with the device.
Let it charge for at least twenty minutes, then see if it starts normally.
If there is no image on the screen, press the Sleep/Wake button to attempt to wake the device.
If the screen displays a red battery icon, continue charging the device until the battery is fully charged. Learn more about charging iPhone and iPod touch, or iPad.
If the above steps do not resolve the issue, or the if the screen remains black or shows a persistent Apple logo, try restoring with iTunes:
Connect the device to your computer and open iTunes.
If the device appears in iTunes, select and click Restore on the Summary pane. Learn more aboutrestoring iOS software.
If the device doesn't appear in iTunes, try to force the device into recovery mode, and then restore it.
If the above steps do not resolve the issue, contact Apple.
iOS: Not responding or does not turn on
http://support.apple.com/en-us/TS3281
Cheers,
Allen -
Canvas flashes red on playback, resart needed
has anyone else encountered the following FCP bug since the last round of apple updates:
FCP works fine for hours then every playback n the canvas flashes red; as if there is a frame of video then a frame of pure red, then a frame of video etc. It's red strobing effect. I need to restart my mac to get the problem to disappear.
Is this a known issue?
It's only happened since I last updated the OS, pro apps etc
thanksI just had this issue too.. and solved it.
red flashes with jpeg-codec.mov / prores422.mov and I'm running a bunch of apps and have nvidia card.
I realised that I was playing a youtube video in the background through safari.
When it stopped, which was the only change I made, the flashes went...
THEREFORE.. the problem was that there is not enough memory/power/whatever is needed to refresh the fcp canvas at a suitable framerate so it was lowered automatically to suit the memory - red possibly just being a default colour to warn.
simples. -
Flashing Red Dot on Location in Map
Hey there,
Does anyone know how to create a flashing red dot around a
location in a map? Here's an example of what I'm talking about in
case you think it's gibberish!
http://www.jimmys-bar.com/location.php
Cheers in advance of any help!That map was rendered in Adobe FLASH program.
A simpler alternative would be a GIF animation.
"Fun Leprechaun" <[email protected]> wrote
in message
news:frpb92$f6n$[email protected]..
> Hey there,
>
> Does anyone know how to create a flashing red dot around
a location in a
> map?
> Here's an example of what I'm talking about in case you
think it's
> gibberish!
>
>
http://www.jimmys-bar.com/location.php
>
> Cheers in advance of any help!
> -
Dell switch 8024F - Front left LED is flashing red - no connect terminal
Hello,
I have a DELL 8024F switch not connected console me.
The console cable is correct.
The LEDs on the switch are as follows:
LED right power source is green.
Left power source does not exist.
LED fans are green.
Front left LED is flashing red.
What can happen?
I have inserted several SFP + and are led as if they were not inserted.
I get the feeling as if you did not initiate the boot process.
Any suggestions?
regardsHi,
The blinking LED typical means a non critical error, but if you can’t connect to console and it doesn’t recognize any SFP+ transceivers, it could be a more serious error. If you unplug it and then reconnect power is there any change? Have you reseated the power supply and fan modules? -
My NVG589 router is flashing red on the Broadband 2 line. How do I fix this?
Hi, There were some storms that came throught my area yesterday/last night and my router now has the Broadband2 line flashing red. I've reset my router twice now and it still keeps doing it. It appears that this is related to my email since I haven't been able to receive email since that happened. I can surf the web, but cannot receive email. Help!! John
Hi
You require a technician to come out. Call AT&T by dialing 800.288.2020 or live chatting with them by clicking the link below and clicking "Chat Now":
http://www.att.com/contactus/index/internet.html
The email issue is likely separate from this issue. When it comes to your Broadband 2 light, it's indicating a problem with one of the cable pairs within your line that needs to be checked.
For the email part, see the link below -
https://forums.att.com/t5/Email-Internet-Security/not-receiving-some-emails/m-p/4281027#M24758
Maybe you are looking for
-
Open field for cost center on the material master
We have a unique requirement in a facility we intend to implement plant maintenance in to track a cost center to a material by including the cost center on the material master somewhere. Cost center is not a field on any of the material tabs we use
-
This problem developed in mid December. the synching worked perfectly on my 18 month old iPad 2 until then. Now the iPad will not sink my calendar, contacts and notes from my desktop Outlook program. It does seem to sync my pictures. the wirel
-
Hi, Is there a way to execute an exe file that is inside the jar with the main class? Right now, I am copying the file to a folder, and executing it. Thanks
-
Maximum number of Lock Entries
Hi Guys, I'm doing some WBS Settlements through CJ88/CJB1 . It might happen that this Txn may process thousands of WBS Elements at a time which means all those WBS Elements will be locked . How to find out the maximum Lock entries in SAP ? I want to
-
Redirect to another page and set the error or success message from process
I have a process that runs when a page is submitted. In the process I am catching an exception and if an exception occurs I want to redirect to a different page and display the error message of the exception. How can this be done? Below is my code. T