Sys-suspend fails on Solaris 9 with tape drive present

I ran across a post by T. Kloeber (http://forum.java.sun.com/thread.jspa?threadID=5109999&messageID=9374786) on the Sun developer forum on this.
I replaced my Solaris 7 SS5 with an Ultra 2 and installed Solaris 9 fresh. The external disks and tape drive are unchanged. The SS5 used to suspend properly about 95% of the time, but now the machine refuses to suspend with the tape drive connected. Log messages are:
Mar 21 16:20:13 madera cpr: [ID 535284 kern.notice] System is being suspended
Mar 21 16:20:24 madera cpr: [ID 122848 kern.warning] WARNING: Unable to suspend device st@4,0.
Mar 21 16:20:24 madera cpr: [ID 537702 kern.warning] WARNING: Device is busy or does not support suspend/resume.
Mar 21 16:20:30 madera cpr: [ID 457896 kern.notice] NOTICE: Suspend operation failed.
Mar 21 16:20:30 madera cpr: [ID 583038 kern.notice] System has been resumed.
and the system is not suspended. Is there anything i am missing on Solaris 9?
I am able to modunload the st driver, then when I attempt to suspend, the driver gets reloaded, and I get the failure above.
I ran across an E10000 service manual from 2.6 days that said that tape devices were not suspendable. They must have rethought that by Solaris 7. No idea why 9 should refuse this. I have the latest recommended patches.
TIA for any information!
TW

Similar Messages

Solaris 8 - IDE Tape Drive

Greetings!
I have Solaris 8 x86 up and running, but cannot get it to identify my HP Colorado 8 GB IDE tape drive. A 'dmesg' reports it found, 'devfsadm' will not create any links to /dev/rmt/.
Any ideas, or is it simply not supported?
-Dave Minor

Hello
back after a long while ... but I have the solution !
Darren, you were completely right, thanks ! I summarize if ever someone meets the same pb ...
1- normally, if the daemon "vold" is running, when inserting a CDROM in a drive, it's automatically mounted and then accessible with /cdrom/cdrom0
2- but, if "vold" is not running, it has to be launched :
/etc/init.d/volmgt start
3- if "vold" is running but you still can't access to your CDROM (it was my case !) => that means the CDROM is maybe not readable ! Actually I had a CD-RW and the drive couldn't read it. I copied the data on a normal CD-R and it worked !
thanks for help !
bye

RMAN Integration with Tap drive

Dear All,
Can any body help me how to integrate RMAN with tap on HP-Unix.
Regards,

To intergrate with RMAN, you should review the install instructions of whichever 3rd party backup software you are using. After you have the software integrated, you can refer to Configuring RMAN to Make Backups to a Media Manager.

Tape Drive Upgrade

I'm running a SunFire v440 with a IBM 3584 tape library. Solaris 9 is the OS and Veritas NetBackup 5.1 is the App. Currently the IBM 3584 has LTO-2 drives in it and the backup team wants to upgrade to LTO-3 drives. They are planning on using the same WWN's thinking this will make the transition easier. I've never worked with tape drives before and need to know if this is valid.
Also, to get the drives visable to Netbackup does anything have to be done at the OS level? I've reviewed the sg.conf file and don't see anything that stands out but my knowledge of this is limited.
Any help will be greatly appreciated.

Hi,
After changing the drives (if they are fiber native) the WWN�s will change since each fiber device has a unique WWN like a MAC. (remember zoning on the fiber switch also needs to be done to accommodate the new hardware.)
It is best to 1st unconfigure the old devices:
cfgadm �al will display the information you require to see where the drives bind to c(#)
run cfgadm �c unconfigure c(#) to remove the old tape drives from the configuration.
Now run the clean-up devfsadm �C
Replace the drives with the LTO-3 units and zone the switch accordingly unless you use a switch that makes use of VSAN.
Reboot tape library
Run the configuration cfgadm �c configure c(#) you might need to do a force update in some cases: cfgadm �c configure �o force_update c(#)
List the devices cfgadm �al
If all is well up to this point you are set from the OS side.
You will need to reconfigure the storage devices in Netbackup since the serial numbers of the drives are now different.
Make sure you follow the guidelines for adding the correct values for LTO3 to the two files listed below to make sure your drives perform at their peak.
/usr/openv/netbackup/db/config/NUMBER_DATA_BUFFERS
/usr/openv/netbackup/db/config/SIZE_DATA_BUFFERS
Hope this helps.

Tape drive and pci-x card with Solaris 10 on VMWare environment

I have a Sun X4170 server (x84_64) running VMWare ESXi 4.0. On it I have two VM guests- my production file server running Solaris 10 U7 and a test file server running Solaris 10 U9.
The X4170 has a PCI-X LSI Logic dual external U320 parallel scsi card. I have a tape drive + auto loader cabled to the X4170. It is a Quantum branded autoloader but I believe the tape drive itself is HP. The autoloader+tape drive share a single SCSI ID (6) but have separate LUNS.
I have two choices for making this system accessible to the OS:
- Virtualize the tape drive and loader individually.
- In VMWare, enable the scsi card as a pass through device. The SCSI card is then added as PCI device to the virtual machine (actually two devices since it is a dual scsi card.)
I had virtualized a single-drive tape drives with Vmware in the past.
However, when I tried I virtualize tape drive and loader, Solaris complained about the scsi id’s being invalid. I don’t think it likes two devices with a single scsi ID. Also, I think I need the backup software to see the REAL tape drive and autoloader (for inventory, changing tapes etc)
On the Solaris 10 U9 “Test” machine:
# cfgadm -al
Ap_Id Type Receptacle Occupant Condition
c1 scsi-bus connected configured unknown
c1::dsk/c1t0d0 disk connected configured unknown
mpt1:scsi scsi-bus connected configured unknown
mpt1:scsi::rmt/0 tape connected configured unknown
mpt1:scsi::scsi/changer/c2t6d med-changer connected configured unknown
mpt2:scsi scsi-bus connected unconfigured unknown
cfgadm: Configuration administration not supported: Error: hotplug service is pr
obably not running, please use 'svcadm enable hotplug' to enable the service. Se
e cfgadm_shp(1M) for more details.
bash-3.00# mt status
/dev/rmt/0n: no tape loaded or drive offline
bash-3.00#
# svcadm enable hotplug
# cfgadm -al
Ap_Id Type Receptacle Occupant Condition
c1 scsi-bus connected configured unknown
c1::dsk/c1t0d0 disk connected configured unknown
mpt1:scsi scsi-bus connected configured unknown
mpt1:scsi::rmt/0 tape connected configured unknown
mpt1:scsi::scsi/changer/c2t6d med-changer connected configured unknown
mpt2:scsi scsi-bus connected unconfigured unknown
pcie160 scsi/hp connected configured ok
pcie161 unknown empty unconfigured unknown
pcie162 unknown empty unconfigured unknown
On the Solaris 10 U7 “Production” machine:
The hotplug service did not exist until I installed the following patches
142934-02 SunOS 5.10_x86: failsafe patch
142910-17 SunOS 5.10_x86: kernel patch
144489-02 SunOS 5.10_x86: kernel patch
# svcadm enable hotplug
# cfgadm -al
Ap_Id Type Receptacle Occupant Condition
c1 scsi-bus connected configured unknown
c1::dsk/c1t0d0 disk connected configured unknown
c1::scsi/direct/c1t0d0 disk connected configured unknown
c4 scsi-bus connected unconfigured unknown
c5 scsi-bus connected unconfigured unknown
pcie160 scsi/hp connected configured ok
Running “devfsadm –v “ does not change anything
Any ideas? Maybe a need to update the MPT driver or is that dangerous?
Thanks

Actually, updating the kernel patches (and enabling hot plug service) did solve the problem. At some point during between testing the system before and after patching, the tape drive got turned off. Since the system patching was being done remotely it was not immediately obvious that the tape drive was off.

Failed to install Solaris 10 with Jump Start

Hi all:
When install Solaris 10 with Jump Start method. I met below error:
<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<
{3} ok boot net -install
SC Alert: Host System has Reset
Probing system devices
Probing memory
Probing I/O buses
screen not found.
Rebooting with command: boot net -install
Use is subject to license terms.
whoami: no domain name
Hardware watchdog enabled
WARNING: exec(nstall) failed (file not found).
(Could not start init) Program terminated
{1} ok
Thanks a lots!

thats because you wrote "-install", which will be parsed as "-i nstall", hence your system will try to execute a kernel named "nstall".
The proper syntax is "boot net - install", with spaces on both sides of the -.
.7/M.

Solaris x86 with Oracle RAC 10g Enterprise Edition Release 10.2.0.3.0

Hello,
Maybe you can help me (new on RMAN backup) in doing this.
I have configured a single Oracle 10g database to have backup with RMAN with following steps:
1. $ mkdir $ORACLE_BASE/rman_scripts
2. $ mkdir $ORACLE_BASE/logs
3. $ mkdir $ORACLE_BASE/tracking
4. $ mkdir $ORACLE_BASE/c_backup
5. $ sqlplus sys/<password> as sysdba
6. SQL> alter system set db_recovery_file_dest_size = 50G scope=both;
7. SQL> alter system set db_recovery_file_dest='${ ORACLE_BASE}/flash_recovery_ area' scope=both;
8. SQL> alter system set log_archive_dest_10='location= use_db_recovery_file_dest';
9. SQL> shutdown immediate
10. SQL> startup nomount
11. SQL> alter database archivelog;
12. SQL> alter database open;
13. SQL> alter database enable block change tracking using file '${ORACLE_BASE}/tracking/rman_ change_track.f';
14. $ rman target /
15. RMAN> CONFIGURE CONTROLFILE AUTOBACKUP FORMAT FOR DEVICE TYPE DISK
TO '/var/opt/oracle/flash_ recovery_area/ORCL/c_backup/% F';
16. RMAN> CONFIGURE CONTROLFILE AUTOBACKUP ON;
17. RMAN> CONFIGURE BACKUP OPTIMIZATION ON;
18. RMAN> CONFIGURE RETENTION POLICY TO RECOVERY WINDOW OF 7 DAYS;
19. RMAN> exit
I need to configure incremental backup with RMAN on a two node Solaris x86 with Oracle RAC 10g Enterprise Edition Release 10.2.0.3.0 installation.
We also use ASM to store database files, and have Oracle software installed on separate file systems (two Oracle roots for Node1 and Node2).
I have following questions:
1) where to put Flash Recovery Area (FRA)?
I saw recommendations to put FRA on the ASM, is this the best way to do it?
2) Can I put FRA on another file system (not on the ASM) which is available only from Node1? This way I can save space on the ASM.
3) Is it possible/recommended to run RMAN from Node1 only?
Below is the script used to run RMAN on the normal Oracle database (without RAC) which I need to change :
=============================================================================================
2.0 Oracle backup script: /opt/app/oracle/rman_scripts/backup.sh
Use this for daily backups, possiblly as a cron job.
Once a week run this: /opt/app/oracle/rman_scripts/backup.sh FULL
All other days of the week: /opt/app/oracle/rman_scripts/backup.sh INCREMENTAL
Note: You may have to change ORACLE_SID, ORACLE_BASE below to match your database.
=============================================================================================
#!/usr/bin/ksh
ORACLE_SID=orcl
ORACLE_BASE=/opt/app/oracle
ORACLE_HOME=${ORACLE_BASE}/product/10.2.0/db_1
PATH=${ORACLE_HOME}/bin:/usr/bin
LOGDIR=${ORACLE_BASE}/logs
LOGFILE=${LOGDIR}/rman.log
if [[ $# < 1 ]]
then
echo "usage: backup.sh FULL|INCREMENTAL"
exit;
fi
BACKUPTYPE=${1}
full='FULL'
incremental='INCREMENTAL'
if [[ $BACKUPTYPE == $full ]]
then
$ORACLE_HOME/bin/rman target / nocatalog log ${LOGFILE} append << eof
run {
backup database;
SQL 'alter system archive log current';
backup archivelog all;
delete noprompt obsolete;
exit;
eof
echo ''
fi
if [[ $BACKUPTYPE == $incremental ]]
then
$ORACLE_HOME/bin/rman target / nocatalog log ${LOGFILE} append << eof
run {
backup database;
backup incremental level 1 database;
SQL 'alter system archive log current';
backup archivelog all;
delete noprompt obsolete;
exit;
eof
echo ''
fi

Hi [email protected],
Q1) where to put Flash Recovery Area (FRA)?
A1) With RAC: on the shared storage
I saw recommendations to put FRA on the ASM, is this the best way to do it?
If you want your backups to be available for both nodes you have to use shared storage or tape using an mml library.
So if you want to use the FRA for rman backups and the database is on ASM just make ASM the standard for the FRA as well.
Q2) Can I put FRA on another file system (not on the ASM) which is available only from Node1? This way I can save space on the ASM.
A2) Than you cannot recover in case Node1 is down. Best would be to send your storage admin to a training course so he can manage the clustered raw devices needed for ASM.
Q3) Is it possible/recommended to run RMAN from Node1 only?
A3) No see A2.
Regards,
Tycho

Autoconfig failed for jtfictx.sh with DRG-10595

After migrating the Oracle Applications 11.5.10.2 from Solaris to Linux the autoconfig failed for Application server with the following:
Executing script in InstantiateFile:
/u01/applvcaprod/vcaprodcomn/admin/install/VCAPROD_yavcaoraprod/jtfictx.sh
script returned:
jtfictx.sh started at Mon Nov 7 16:32:11 EST 2011
SQL*Plus: Release 8.0.6.0.0 - Production on Mon Nov 7 16:32:11 2011
(c) Copyright 1999 Oracle Corporation. All rights reserved.
Enter value for 1: Enter value for 2: Enter value for 3: Connected.
DECLARE
ERROR at line 1:
ORA-29874: warning in the execution of ODCIINDEXALTER routine
ORA-29960: line 1,
DRG-10595: ALTER INDEX JTF_AMV_ITEMS_URL_CTX failed
DRG-10561: index JTF_AMV_ITEMS_URL_CTX is not valid for requested operation
ORA-06512: at "SYS.DBMS_SYS_SQL", line 909
ORA-06512: at "SYS.DBMS_SQL", line 39
ORA-06512: at line 96
Also tried to build these indexes by running jtfiaibu.sql didn't help:
sqlplus apps/apps @jtfiaibu.sql JTF JTF APPS
ERROR at line 1:
ORA-29855: error occurred in the execution of ODCIINDEXCREATE routine
ORA-20000: Oracle Text error:
DRG-10700: preference does not exist: APPS.jtf_url_datastore
ORA-06512: at "CTXSYS.DRUE", line 160
ORA-06512: at "CTXSYS.TEXTINDEXMETHODS", line 364
ORA-06512: at "SYS.DBMS_SYS_SQL", line 909
ORA-06512: at "SYS.DBMS_SQL", line 39
ORA-06512: at line 37
Greatly appreciate any help on this.

Thanks for the update. I already tried all the above mentions documents it didn't wotk. Also there are no invalid objects in CTXSYS schema and the database is 10.2.0.5
As i specified earlier witht he doc 1271186.1 when i try to execute the
sqlplus apps/apps @jtfiaibu.sql JTF JTF APPS
it failed with the following .
ERROR at line 1:
ORA-29855: error occurred in the execution of ODCIINDEXCREATE routine
ORA-20000: Oracle Text error:
DRG-10700: preference does not exist: APPS.jtf_url_datastore
ORA-06512: at "CTXSYS.DRUE", line 160
ORA-06512: at "CTXSYS.TEXTINDEXMETHODS", line 364
ORA-06512: at "SYS.DBMS_SYS_SQL", line 909
ORA-06512: at "SYS.DBMS_SQL", line 39
ORA-06512: at line 37

Backup strategy with no tape drives/library

Hi, I am new into the job of sys admin, so we recently setup a system with running solaris 10 and with its storage as a NetApp, but we do not have yet a library or tape drive attached to it.
So how can I approach this problem? Can I setup a LUN on NetApp and copy all important stuff to that LUN?
FR

For the oracle backup, oracle should have comands to dump or export the database to a file, and that file could be backed up. Alternately, there are problably options to put the database in read-only mode, so that you can back up the database files without worrying that they will be changed during the backup.
For other files, if you are using zfs snapshots, you could back up the zfs snapshots even if the original file is still open.
You might also want to look at the rysnc command- that should let you back up only files that have differ between the source and destination (i.e. you could do differential backups.) So maybe you could a monthly full backup with tar to NAS or SAN, a weekly rsync incremental backup, and daily zfs snapshot that is kept for a week.

[Solved] Systemd suspend fails everytime

Hi,
I've been using Arch Linux on my laptop for a while now and suddenly my laptop would not go into suspend anymore.
My laptop is Asus UX32VD.
Here's the whole journalctl between suspend starting and suspend failing.
I also get this at bootup:
[drm:intel_dp_start_link_train] *ERROR* too many voltage retries, give up
some while ago the iSSD in my laptop failed but it was later that the computer stopped suspending.
Does anyone see the problem?
Thanks.
Edit: When I try to mount the iSSD partitions I get the same error messages that begin with "ata2.00" so those errors seem to be connected to the iSSD drive. Now, I can't disable the drive in bios, is it possible to make arch linux ignore it all together?
Edit2: Arch Linux is installed on sda (ata1) and the bad drive is sdb (ata2)
Edit3: The broken ssd was the culprit. When I write 1 to /sys/block/sdb/device/delete the laptop suspends correctly.
So I made the following systemd service:
[Unit]
Description=Disable my fault ssd drive at suspend
[Service]
Type=OneShot
ExecStart=/bin/sh -c 'echo 1 > /sys/block/sdb/device/delete'
[Install]
WantedBy=sleep.target
Changing status to solved
Last edited by granra (2014-04-18 23:01:57)

Rexilion wrote:What is stopping you from taking it out?
It's soldered to the motherboard.

Storagetek LTO3 tape drive cannot detact in solaris 9

Hi, i have a problem regarding the installation of LTO3 tape drive to my SunFire V880.
The scenario is like this. I have 2 SunFire v880 and 1 SunFire 280R. Each of them using external lto3 tape drive. But 2 of them is working fine.Only 1 server has a problem. which is one of the v880.
Below are the patch for my Solaris 9
1. V880 - 118558-24 (tape drive detected)
2. V880 - 112233-11 (tape drive not detected)
3. 280R - 112233-11. (tape drive detected)
What makes me confused is at the tape drive documentation says that the tape drive only can be used for the patch higher than 112233-11 . But i can see that there is no problem with 280R. The scsi card and tape drive is the same model for all three servers.
I have run setevnv auto-boot? false, reset-all ,probe-scsi-all but still cannot run.
When I ls in /dev/rmt..there is no files in it.Can somebody help me..Tq

Hello,
The scsi card and tape drive is the same model for all three servers.
I have run setevnv auto-boot? false, reset-all ,probe-scsi-all but still cannot run.
If the drive isn't displayed by probe-scsi-all, check the cable and terminators.
Even if no SCSI device is detected, the controller itself should be displayed.
Maybe the external port of the controller has failed.
If the drive is displayed advance to the next step.
When I ls in /dev/rmt..there is no files in it.
Did you boot with the reconfiguration option ? Solaris 9 supports devfsadm to rebuild the device-tree without reboot, but if you can afford the downtime, a reboot is prefered.
Without reboot: devfsadm -C -c tape -v
This is a link to an online version of the manpage http://man.cx/devfsadm(1M)
With reboot: Either touch /reconfigure; init 6 or boot -r from the ok-prompt.
A feedback is appreciated (didn't help, component failed, etc.) !
Michael

Suspends fails the first time, but succeeds the second time

Hi all,
I am running Arch Linux on my Dell XPS 15 9530 laptop, and overall I am very happy with the combination. I have however had some issues with suspending.
The problem is that the first time I try to suspend the machine it seems to go to sleep, but then two seconds later it automatically wakes up again. If I then immediately try again to suspend, it works (it does not wake up automatically). Does anyone know what could be going on, and how this can be fixed?
Usually I suspend from my gnome 3 desktop, but I have also tried to suspend directly using 'systemctl suspend' without having an X server running, and the result is exactly the same. I have tried a few versions of the vanilla kernel, but also the linux-lts and the linux-ck images, but to no avail.
Here is the output from dmesg, where suspend fails:
PM: Syncing filesystems ... done.
PM: Preparing system for mem sleep
bbswitch: enabling discrete graphics
Freezing user space processes ... (elapsed 0.543 seconds) done.
Freezing remaining freezable tasks ... (elapsed 0.001 seconds) done.
PM: Entering mem sleep
Suspending console(s) (use no_console_suspend to debug)
sd 1:0:0:0: [sda] Synchronizing SCSI cache
smsc75xx 3-1:1.0 enp0s20u1: entering SUSPEND2 mode
sd 1:0:0:0: [sda] Stopping disk
Removing pn544
PM: suspend of devices complete after 334.544 msecs
PM: late suspend of devices complete after 0.201 msecs
ehci-pci 0000:00:1d.0: System wakeup enabled by ACPI
ehci-pci 0000:00:1a.0: System wakeup enabled by ACPI
xhci_hcd 0000:00:14.0: System wakeup enabled by ACPI
PM: noirq suspend of devices complete after 26.944 msecs
ACPI: Preparing to enter system sleep state S3
PM: Saving platform NVS memory
Disabling non-boot CPUs ...
kvm: disabling virtualization on CPU1
smpboot: CPU 1 is now offline
kvm: disabling virtualization on CPU2
smpboot: CPU 2 is now offline
kvm: disabling virtualization on CPU3
smpboot: CPU 3 is now offline
kvm: disabling virtualization on CPU4
smpboot: CPU 4 is now offline
kvm: disabling virtualization on CPU5
smpboot: CPU 5 is now offline
kvm: disabling virtualization on CPU6
smpboot: CPU 6 is now offline
kvm: disabling virtualization on CPU7
smpboot: CPU 7 is now offline
ACPI: Low-level resume complete
PM: Restoring platform NVS memory
Enabling non-boot CPUs ...
x86: Booting SMP configuration:
smpboot: Booting Node 0 Processor 1 APIC 0x2
kvm: enabling virtualization on CPU1
Intel pstate controlling: cpu 1
CPU1 is up
smpboot: Booting Node 0 Processor 2 APIC 0x4
kvm: enabling virtualization on CPU2
Intel pstate controlling: cpu 2
CPU2 is up
smpboot: Booting Node 0 Processor 3 APIC 0x6
kvm: enabling virtualization on CPU3
Intel pstate controlling: cpu 3
CPU3 is up
smpboot: Booting Node 0 Processor 4 APIC 0x1
kvm: enabling virtualization on CPU4
Intel pstate controlling: cpu 4
CPU4 is up
smpboot: Booting Node 0 Processor 5 APIC 0x3
kvm: enabling virtualization on CPU5
Intel pstate controlling: cpu 5
CPU5 is up
smpboot: Booting Node 0 Processor 6 APIC 0x5
kvm: enabling virtualization on CPU6
Intel pstate controlling: cpu 6
CPU6 is up
smpboot: Booting Node 0 Processor 7 APIC 0x7
kvm: enabling virtualization on CPU7
Intel pstate controlling: cpu 7
CPU7 is up
ACPI: Waking up from system sleep state S3
acpi LNXPOWER:01: Turning OFF
xhci_hcd 0000:00:14.0: System wakeup disabled by ACPI
ehci-pci 0000:00:1a.0: System wakeup disabled by ACPI
ehci-pci 0000:00:1d.0: System wakeup disabled by ACPI
PM: noirq resume of devices complete after 73.424 msecs
PM: early resume of devices complete after 0.091 msecs
mei_me 0000:00:16.0: irq 49 for MSI/MSI-X
snd_hda_intel 0000:00:03.0: irq 50 for MSI/MSI-X
snd_hda_intel 0000:00:1b.0: irq 53 for MSI/MSI-X
mei_me 0000:00:16.0: NFC MEI VERSION: IVN 0x1 Vendor ID 0x1 Type 0x1
Probing NFC pn544
ata2: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
ata2.00: failed to get NCQ Send/Recv Log Emask 0x1
usb 3-1: reset high-speed USB device number 2 using xhci_hcd
xhci_hcd 0000:00:14.0: Setup ERROR: setup context command for slot 1.
ata2.00: failed to get NCQ Send/Recv Log Emask 0x1
ata2.00: configured for UDMA/133
sd 1:0:0:0: [sda] Starting disk
usb 3-1: reset high-speed USB device number 2 using xhci_hcd
xhci_hcd 0000:00:14.0: Setup ERROR: setup context command for slot 1.
usb 3-1: reset high-speed USB device number 2 using xhci_hcd
xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff88007fd75180
xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff88007fd751c0
xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff88007fd75200
smsc75xx 3-1:1.0 enp0s20u1: resuming from SUSPEND2
usb 3-4: reset full-speed USB device number 3 using xhci_hcd
xhci_hcd 0000:00:14.0: Setup ERROR: setup context command for slot 2.
usb 3-4: reset full-speed USB device number 3 using xhci_hcd
xhci_hcd 0000:00:14.0: Setup ERROR: setup context command for slot 2.
usb 3-4: reset full-speed USB device number 3 using xhci_hcd
xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff8804148f9ac0
xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff8804148f9a80
xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff8804148f9a40
usb 3-6: reset full-speed USB device number 4 using xhci_hcd
xhci_hcd 0000:00:14.0: Setup ERROR: setup context command for slot 3.
usb 3-6: reset full-speed USB device number 4 using xhci_hcd
xhci_hcd 0000:00:14.0: Setup ERROR: setup context command for slot 3.
[drm] Enabling RC6 states: RC6 on, RC6p off, RC6pp off
usb 3-6: reset full-speed USB device number 4 using xhci_hcd
xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff8804174ddc80
xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff8804174ddcc0
usb 3-11: reset high-speed USB device number 6 using xhci_hcd
xhci_hcd 0000:00:14.0: Setup ERROR: setup context command for slot 5.
usb 3-11: reset high-speed USB device number 6 using xhci_hcd
xhci_hcd 0000:00:14.0: Setup ERROR: setup context command for slot 5.
usb 3-11: reset high-speed USB device number 6 using xhci_hcd
xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff8804148f9480
xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff8804148f9440
usb 3-9: reset full-speed USB device number 5 using xhci_hcd
xhci_hcd 0000:00:14.0: Setup ERROR: setup context command for slot 4.
usb 3-9: reset full-speed USB device number 5 using xhci_hcd
xhci_hcd 0000:00:14.0: Setup ERROR: setup context command for slot 4.
pciehp 0000:00:1c.0:pcie04: Link Training Error occurs
pciehp 0000:00:1c.0:pcie04: Failed to check link status
dpm_run_callback(): pnp_bus_resume+0x0/0xa0 returns -19
PM: Device 00:08 failed to resume: error -19
usb 3-9: reset full-speed USB device number 5 using xhci_hcd
xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff8804181db000
xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff8804181db040
xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff8804181db080
xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff880417451e80
xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff880417451ec0
PM: resume of devices complete after 2769.054 msecs
PM: Finishing wakeup.
Restarting tasks ...
iwlwifi 0000:06:00.0: no hotplug settings from platform
rtsx_pci 0000:07:00.0: no hotplug settings from platform
done.
Bluetooth: hci0: read Intel version: 370710018002030d00
Bluetooth: hci0: Intel Bluetooth firmware file: intel/ibt-hw-37.7.10-fw-1.80.2.3.d.bseq
video LNXVIDEO:00: Restoring backlight state
video LNXVIDEO:01: Restoring backlight state
bbswitch: disabling discrete graphics
ACPI Warning: \_SB_.PCI0.PEG0.PEGP._DSM: Argument #4 type mismatch - Found [Buffer], ACPI requires [Package] (20131218/nsarguments-95)
Bluetooth: hci0: Intel Bluetooth firmware patch completed and activated
smsc75xx 3-1:1.0 enp0s20u1: link down
smsc75xx 3-1:1.0 enp0s20u1: link down
smsc75xx 3-1:1.0 enp0s20u1: kevent 4 may have been dropped
smsc75xx 3-1:1.0 enp0s20u1: link down
smsc75xx 3-1:1.0 enp0s20u1: link down
and here where suspend succeeds:
smsc75xx 3-1:1.0 enp0s20u1: kevent 4 may have been dropped
smsc75xx 3-1:1.0 enp0s20u1: link up, 100Mbps, full-duplex, lpa 0xC5E1
smsc75xx 3-1:1.0 enp0s20u1: link up, 100Mbps, full-duplex, lpa 0xC5E1
PM: Syncing filesystems ... done.
PM: Preparing system for mem sleep
bbswitch: enabling discrete graphics
Freezing user space processes ... (elapsed 0.412 seconds) done.
Freezing remaining freezable tasks ... (elapsed 0.001 seconds) done.
PM: Entering mem sleep
Suspending console(s) (use no_console_suspend to debug)
sd 1:0:0:0: [sda] Synchronizing SCSI cache
smsc75xx 3-1:1.0 enp0s20u1: entering SUSPEND2 mode
sd 1:0:0:0: [sda] Stopping disk
Removing pn544
PM: suspend of devices complete after 780.265 msecs
PM: late suspend of devices complete after 0.387 msecs
ehci-pci 0000:00:1d.0: System wakeup enabled by ACPI
ehci-pci 0000:00:1a.0: System wakeup enabled by ACPI
xhci_hcd 0000:00:14.0: System wakeup enabled by ACPI
PM: noirq suspend of devices complete after 26.988 msecs
ACPI: Preparing to enter system sleep state S3
PM: Saving platform NVS memory
Disabling non-boot CPUs ...
kvm: disabling virtualization on CPU1
smpboot: CPU 1 is now offline
kvm: disabling virtualization on CPU2
smpboot: CPU 2 is now offline
kvm: disabling virtualization on CPU3
smpboot: CPU 3 is now offline
kvm: disabling virtualization on CPU4
smpboot: CPU 4 is now offline
kvm: disabling virtualization on CPU5
smpboot: CPU 5 is now offline
kvm: disabling virtualization on CPU6
smpboot: CPU 6 is now offline
kvm: disabling virtualization on CPU7
smpboot: CPU 7 is now offline
ACPI: Low-level resume complete
PM: Restoring platform NVS memory
Enabling non-boot CPUs ...
x86: Booting SMP configuration:
smpboot: Booting Node 0 Processor 1 APIC 0x2
kvm: enabling virtualization on CPU1
Intel pstate controlling: cpu 1
CPU1 is up
smpboot: Booting Node 0 Processor 2 APIC 0x4
kvm: enabling virtualization on CPU2
Intel pstate controlling: cpu 2
CPU2 is up
smpboot: Booting Node 0 Processor 3 APIC 0x6
kvm: enabling virtualization on CPU3
Intel pstate controlling: cpu 3
CPU3 is up
smpboot: Booting Node 0 Processor 4 APIC 0x1
kvm: enabling virtualization on CPU4
Intel pstate controlling: cpu 4
CPU4 is up
smpboot: Booting Node 0 Processor 5 APIC 0x3
kvm: enabling virtualization on CPU5
Intel pstate controlling: cpu 5
CPU5 is up
smpboot: Booting Node 0 Processor 6 APIC 0x5
kvm: enabling virtualization on CPU6
Intel pstate controlling: cpu 6
CPU6 is up
smpboot: Booting Node 0 Processor 7 APIC 0x7
kvm: enabling virtualization on CPU7
Intel pstate controlling: cpu 7
CPU7 is up
ACPI: Waking up from system sleep state S3
acpi LNXPOWER:01: Turning OFF
xhci_hcd 0000:00:14.0: System wakeup disabled by ACPI
ehci-pci 0000:00:1a.0: System wakeup disabled by ACPI
ehci-pci 0000:00:1d.0: System wakeup disabled by ACPI
PM: noirq resume of devices complete after 73.411 msecs
PM: early resume of devices complete after 0.097 msecs
mei_me 0000:00:16.0: irq 49 for MSI/MSI-X
snd_hda_intel 0000:00:03.0: irq 50 for MSI/MSI-X
snd_hda_intel 0000:00:1b.0: irq 53 for MSI/MSI-X
mei_me 0000:00:16.0: NFC MEI VERSION: IVN 0x1 Vendor ID 0x1 Type 0x1
Probing NFC pn544
ata2: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
ata2.00: failed to get NCQ Send/Recv Log Emask 0x1
usb 3-4: reset full-speed USB device number 3 using xhci_hcd
xhci_hcd 0000:00:14.0: Setup ERROR: setup context command for slot 2.
ata2.00: failed to get NCQ Send/Recv Log Emask 0x1
ata2.00: configured for UDMA/133
sd 1:0:0:0: [sda] Starting disk
usb 3-4: reset full-speed USB device number 3 using xhci_hcd
xhci_hcd 0000:00:14.0: Setup ERROR: setup context command for slot 2.
usb 3-4: reset full-speed USB device number 3 using xhci_hcd
xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff8804148f9ac0
xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff8804148f9a80
xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff8804148f9a40
usb 3-1: reset high-speed USB device number 2 using xhci_hcd
xhci_hcd 0000:00:14.0: Setup ERROR: setup context command for slot 1.
usb 3-1: reset high-speed USB device number 2 using xhci_hcd
xhci_hcd 0000:00:14.0: Setup ERROR: setup context command for slot 1.
usb 3-1: reset high-speed USB device number 2 using xhci_hcd
xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff88007fd75180
xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff88007fd751c0
xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff88007fd75200
smsc75xx 3-1:1.0 enp0s20u1: resuming from SUSPEND2
usb 3-9: reset full-speed USB device number 5 using xhci_hcd
xhci_hcd 0000:00:14.0: Setup ERROR: setup context command for slot 4.
usb 3-9: reset full-speed USB device number 5 using xhci_hcd
xhci_hcd 0000:00:14.0: Setup ERROR: setup context command for slot 4.
[drm] Enabling RC6 states: RC6 on, RC6p off, RC6pp off
usb 3-9: reset full-speed USB device number 5 using xhci_hcd
xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff8804181db000
xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff8804181db040
xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff8804181db080
xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff880417451e80
xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff880417451ec0
usb 3-6: reset full-speed USB device number 4 using xhci_hcd
xhci_hcd 0000:00:14.0: Setup ERROR: setup context command for slot 3.
usb 3-6: reset full-speed USB device number 4 using xhci_hcd
xhci_hcd 0000:00:14.0: Setup ERROR: setup context command for slot 3.
usb 3-6: reset full-speed USB device number 4 using xhci_hcd
xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff8804174ddc80
xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff8804174ddcc0
usb 3-11: reset high-speed USB device number 6 using xhci_hcd
xhci_hcd 0000:00:14.0: Setup ERROR: setup context command for slot 5.
usb 3-11: reset high-speed USB device number 6 using xhci_hcd
xhci_hcd 0000:00:14.0: Setup ERROR: setup context command for slot 5.
pciehp 0000:00:1c.0:pcie04: Link Training Error occurs
pciehp 0000:00:1c.0:pcie04: Failed to check link status
dpm_run_callback(): pnp_bus_resume+0x0/0xa0 returns -19
PM: Device 00:08 failed to resume: error -19
usb 3-11: reset high-speed USB device number 6 using xhci_hcd
xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff8804148f9480
xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff8804148f9440
PM: resume of devices complete after 2801.389 msecs
PM: Finishing wakeup.
Restarting tasks ...
iwlwifi 0000:06:00.0: no hotplug settings from platform
rtsx_pci 0000:07:00.0: no hotplug settings from platform
done.
Bluetooth: hci0: read Intel version: 370710018002030d00
Bluetooth: hci0: Intel Bluetooth firmware file: intel/ibt-hw-37.7.10-fw-1.80.2.3.d.bseq
video LNXVIDEO:00: Restoring backlight state
video LNXVIDEO:01: Restoring backlight state
bbswitch: disabling discrete graphics
ACPI Warning: \_SB_.PCI0.PEG0.PEGP._DSM: Argument #4 type mismatch - Found [Buffer], ACPI requires [Package] (20131218/nsarguments-95)
Bluetooth: hci0: Intel Bluetooth firmware patch completed and activated
systemd[1]: Requested transaction contradicts existing jobs: File exists
systemd[1]: Service sleep.target is not needed anymore. Stopping.
smsc75xx 3-1:1.0 enp0s20u1: kevent 4 may have been dropped
smsc75xx 3-1:1.0 enp0s20u1: link down
smsc75xx 3-1:1.0 enp0s20u1: link down
It seems to me like the only real difference has to do with the xhci_hcd errors, perhaps the following:
xhci_hcd 0000:00:14.0: Setup ERROR: setup context command for slot 2.
Any input or help would be highly appreciated.

Rexilion wrote:Maybe you could confirm your suspicion by rmmoding xhci before suspend and modprobing it after resume?
Thanks for the response. I should have said so, but I had already tried that, but without any luck. It seems like it doesn't change anything.

Suspend to ram stopped working with Acer Aspire 5930G - Arch64

Suspend to ram recently stopped working on my laptop running Arch64. When ever I press the suspend to ram button in kde4 simply nothing happens, no screen flashing or error messages of any kind. I tried to install the pm-utils package and run pm-suspend, but with the same result. The program just ran and nothing happened and no feedback, not even in dmesg.
Here are the recent packages I've installed:
[2009-05-20 00:53] synchronizing package lists
[2009-05-20 00:53] starting full system upgrade
[2009-05-20 00:54] upgraded cpio (2.9-4 -> 2.9-5)
[2009-05-20 00:54] upgraded curl (7.19.4-1 -> 7.19.5-1)
[2009-05-20 00:54] upgraded gconf (2.26.1-2 -> 2.26.2-1)
[2009-05-20 00:54] upgraded glib2 (2.20.1-1 -> 2.20.2-1)
[2009-05-20 00:54] upgraded gmp (4.3.0-1 -> 4.3.1-2)
[2009-05-20 00:54] upgraded gsl (1.12-1 -> 1.12-2)
[2009-05-20 00:54] upgraded gstreamer0.10 (0.10.22-1 -> 0.10.23-1)
[2009-05-20 00:54] upgraded gstreamer0.10-base (0.10.22-1 -> 0.10.23-1)
[2009-05-20 00:54] upgraded irssi (0.8.12-5 -> 0.8.13-1)
[2009-05-20 00:54] upgraded libdrm (2.4.9-1 -> 2.4.11-1)
[2009-05-20 00:54] upgraded libsndfile (1.0.19-1 -> 1.0.20-1)
[2009-05-20 00:54] upgraded mesa (7.4.1-1 -> 7.4.2-1)
[2009-05-20 00:54] upgraded netcfg (2.1.3-3 -> 2.2.0b1-1)
[2009-05-20 00:54] upgraded poppler (0.10.6-1 -> 0.10.7-1)
[2009-05-20 00:54] upgraded poppler-glib (0.10.6-1 -> 0.10.7-1)
[2009-05-20 00:54] upgraded poppler-qt (0.10.6-1 -> 0.10.7-1)
[2009-05-20 00:54] upgraded ppp (2.4.4-7 -> 2.4.4-8)
[2009-05-20 00:54] upgraded psmisc (22.6-2.1 -> 22.7-1)
[2009-05-20 00:54] upgraded pycairo (1.8.2-1 -> 1.8.4-1)
[2009-05-20 00:54] upgraded subversion (1.6.2-1 -> 1.6.2-2)
[2009-05-21 12:57] installed festival (1.96beta-2)
[2009-05-21 13:01] installed festival-awb-arctic (1.0-1)
[2009-05-21 13:03] removed festival-awb-arctic (1.0-1)
[2009-05-21 13:03] removed festival (1.96beta-2)
[2009-05-21 13:48] installed libmikmod (3.1.12-2)
[2009-05-21 13:48] installed smpeg (0.4.4-5)
[2009-05-21 13:48] installed sdl_mixer (1.2.8-3)
[2009-05-21 13:48] installed ode (0.11-1)
[2009-05-21 13:48] installed sdl_ttf (2.0.9-1)
[2009-05-21 13:48] installed sdl_net (1.2.7-2)
[2009-05-21 13:48] installed xmoto (0.5.1-2)
Note, I tried to do a -Syu just now and got a new kernel, but it did not change anything.
EDIT: I'm also currently running the nvidia 180.60 driver.
Last edited by Avenger (2009-05-22 17:52:05)

search the forums: http://bbs.archlinux.org/viewtopic.php?pid=556030
in the future, i would definately use yaourt to upgrade since it displays better what is being updated and from where.
edit: if pm-suspend fails, check its log (/var/log/pm-suspend.log)
Last edited by eldragon (2009-05-22 18:16:08)

Font command fails on solaris

I have a program which runs fine under Windows but fails in Solaris when it gets to the line
font=new Font(null,FONT.plain,current_font_size);
(I have tried SansSerif and Lucida in place of null.
It is being run from a shell script as a batch process on the server. I have to access fonts to work out size of text objects - I presume my problem is to do with X11 - any advice.

Hi,
Can you provide the error you get?
I guess you do need an X Window System ( http://www.xfree86.org ).
If you already have one, try setting the environment variable DISPLAY as follows:
- log on as root
- for sh ksh:
set DISPLAY=localhost:1.0
export DISPLAY
- or for csh:
setenv DISPLAY=localhost:1.0
If this doesn't work, try replacing 1.0 with 0.0
Regards,
Kurt.

St.conf parameters for SDLT tape drive / Solaris 8

Hello,
I need the parameters for the SDLT tape drive from Tandberg for the st kernel driver. In the st.conf there is no entry for Tandberg SDLT.
With the st.conf, shipped with Solaris 8 10/01, my V880 crashes when accessing the SDLT with the mt command.
Does anyone here have the parameters?
Thanks in advance
Thomas M�ller
department manager IT
Christ GmbH
Germany

Hi Thomas,
Actually, a bug 4495684 has been filed to fix this issue. A 2.6, 7,
8 and SOlaris 9 patch should come out soon that will add this entry
in the st.conf.
I constructed this entries from the bug description. Try if it works.
It should else wait for the patch. Any way, please let me know
the results.
"QUANTUM Super DLT", "Quantum Super DLT", "SDLT-data";
SDLT-data = 1,0x38,0,0x8619,4,0x88,0x89,0x90,0x91,3;
Good Luck !!!
Shridhar

Sys-suspend fails on Solaris 9 with tape drive present

Similar Messages

Maybe you are looking for