Syslog on Cisco Wireless Controller
Hi everyone
I have question about syslog on wireless controller. I need to know what is information in the syslog from controller. I had read paper in the community some siad it has not much in the syslog but it has not detial what is the information in the syslog sent. I know that almost information such as client, authentication, and much benefit logging in the SNMP. So, anyone have any idea or information please give me the idea or information.
Thanks
V
You just need to setup the sylog and try different logging levels to see if it gives you the information you need. YOu might not get what you want or if you find a syslog level that gives you the info you want, you might get a lot of stuff you don't want to see.
http://www.cisco.com/en/US/products/ps6307/products_configuration_example09186a00809a2d76.shtml
Thanks,
Scott
Help out other by using the rating system and marking answered questions as "Answered"
Similar Messages
-
VLAN assignment without ACS on Cisco Wireless Controller 5508
I was wondering if it is possible to do dynamic VLAN assignment on the Cisco Wireless Controller 5508 without using Cisco ACS but use Microsoft NPS server instead? Is there a manual or article that someone can point me in the right direction?
Thank you!Any RADIUS server will allow you to do the dynamic vlan assignment if you configure the right RADIUS attributes (64, 65 and 81 that Steve mentioned above).
This doc shows example of dynamic vlan assignment with WLC and ACS.
http://www.cisco.com/en/US/tech/tk722/tk809/technologies_configuration_example09186a008076317c.shtml
Same config on WLC is needed. However, on the RADIUS you need to configure the same attributes on the NPS instead.
HTH
Amjad
Rating useful replies is more useful than saying "Thank you" -
Cisco wireless controller 4400
Hey all,
I was wondering does the Cisco Wireless controller 4400 come with any management software such as the Cisco Wireless Controller system software?
regards,
MarkWCS doesn't come with your WLC purchase you can down load a trial version of WCS from Cisco site. I think it is a 15 or 30 day trial.
You would have to purchase a license to run a full blown WCS. You can get this in either Linux or Windows.
Hope this helps you.
You can find info on this at:
http://www.cisco.com/en/US/prod/collateral/wireless/ps5755/ps6301/ps6305/product_data_sheet0900aecd804b4646_ps3915_Products_Data_Sheet.html -
How i configure cisco wireless controller
how i can confiure cisco wireless controller
Cisco Wireless LAN Controller Configuration Guide, Release 7.0:
http://www.cisco.com/c/en/us/td/docs/wireless/controller/7-0/configuration/guide/c70.html -
Cisco Wireless controller CT 5760
Does this above mentioned Wireless controller support :
•- Port Based Access Control
•- What is the Switching capacity speed
•- What is the MAC Address table size
Regards,
DravvyHello,
May the link below help you out:-
http://www.cisco.com/en/US/prod/collateral/wireless/ps6302/ps8322/ps12598/data_sheet_c78-722607.html -
WLAN Clients not browsing on Cisco Wireless Controller WLC NME-AIR-WLC12-K9
HiI have a question and i need a solution and expert help.I have done a deployment which involves Security (ASA5540), Routing/voice gateway/wlc NME-AIR-WLC12-k9) and Switching (Cisco3845-ccme/k9)Below is the list of equipment used:1. Cisco ASA 5540 - which is connected at the edge to the ISP router
2. Core Switch WS-C4948E as core and DHCP Server for all VLANs
3. Access/Distribution Switches WS-C3560G-48PS-S connected as trunk to the core switch
4. Router/Voice Gateway/WLC Cisco3845-CCME/K9 - This is the voice gateway and also the WLC
5. Wireless APs AIR-LAP1242AG-E-K9 (12 qty)Here is the deployment scenario:1. G0/0 of the ASA is connected to a 7200 router from the ISP (Public IP Add)
2. G0/1 of the ASA is connected to gig 1/3 on the Core Switch on VLAN 2 which is the management VLAN (Local IP 10.1.1.2)
3. Port 3 of the Core switch is on vlan 2 connected to ASA - Management IP of Core Switch is 10.1.1.1. Core Switch is the DHCP Server for all VLANS on the network.
4. All the Access/Distribution switches are configured with IP Addresses on VLAN 2
5. Telephony Services is configured on the router and DHCP Pool for Access Points and Wireless Clients is running on the router.
6. Two DHCP pools were created on the router for APs and Wireless Clients.
7. G0/0 of the router is configured on the same network that issues dhcp ip to the AP and is connected to gig 1/1 on the core switch
8 G0/1 of the router is configured as the voice port for the IP Telephony Services and is connected to G 1/2 on the core switch1. Clients receiving DHCP IP on the Core Switch can communicate with all vlans and can browse to the Internet.
2. IP Telephony Services is running well.
3. Client on wireless can get IP from the DHCP on the router but cannot browse.I have pings from the router to the core switch and firewall, but clients connected to the wireless
cannot ping other vlans on the core switch and vice versa.The port connecting the router to the core switch is an Access Port, i have changed to to trunk but still no changes.My biggest problem now is how to make the clients on the wireless communicate with other clients on the network and be able to browse to the Internet.Below is the configs on the router and core switch.Router ConfigNimc_Voice_Router#sh run
Building configuration...
Current configuration : 10513 bytes
! Last configuration change at 13:03:55 Nigeria Mon Nov 29 2010 by admin
! NVRAM config last updated at 13:03:56 Nigeria Mon Nov 29 2010 by admin
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname Nimc_Voice_Router
boot-start-marker
boot-end-marker
! card type command needed for slot/vwic-slot 0/2
logging message-counter syslog
enable secret
aaa new-model
! aaa authentication login default local
aaa session-id common
clock timezone Nigeria 1
dot11 syslog
ip source-route
ip dhcp excluded-address 10.1.12.1 10.1.12.10
ip dhcp excluded-address 192.168.1.1 192.168.1.10
ip dhcp pool LWAAP-AP
network 10.1.12.0 255.255.255.0
default-router 10.1.12.1
option 43 hex f104.c0a8.0002
dns-server 83.229.88.30 4.2.2.2 193.238.28.249
option 60 ascii "Cisco AP c1240"
ip dhcp pool Wireless
network 192.168.1.0 255.255.255.0
default-router 192.168.1.1
dns-server 83.229.88.30 193.238.28.249 4.2.2.2
ip cef
no ip domain lookup
ip domain name nimc.gov.ng
ip name-server 83.229.88.30
ip name-server 193.238.28.249
ip name-server 4.2.2.2
no ipv6 cef
multilink bundle-name authenticated
voice-card 0
archive
log config
hidekeys
interface GigabitEthernet0/0
description Connection to AP
ip address 10.1.12.1 255.255.255.0
ip helper-address 192.168.0.2
load-interval 30
duplex auto
speed auto
media-type rj45
interface Service-Engine0/0
no ip address
shutdown
interface GigabitEthernet0/1
ip address 10.1.2.2 255.255.255.0
duplex auto
speed auto
media-type rj45
interface FastEthernet0/0/0
no ip address
shutdown
duplex auto
speed auto
interface Serial0/1/0
no ip address
shutdown
no fair-queue
clock rate 2000000
interface Serial0/1/1
no ip address
shutdown
clock rate 2000000
interface Integrated-Service-Engine1/0
ip address 192.168.0.1 255.255.255.0
no keepalive
interface Integrated-Service-Engine1/0.15
encapsulation dot1Q 15
ip address 192.168.1.1 255.255.255.0
interface Integrated-Service-Engine1/0.100
encapsulation dot1Q 100
ip forward-protocol nd
ip forward-protocol udp 12223
ip route 10.1.0.0 255.255.255.0 10.1.1.1
ip route 10.1.1.0 255.255.255.0 10.1.1.1
ip route 10.1.2.0 255.255.255.0 10.1.1.1
ip route 10.1.3.0 255.255.255.0 10.1.1.1
ip route 10.1.4.0 255.255.255.0 10.1.1.1
ip route 10.1.5.0 255.255.255.0 10.1.1.1
ip route 10.1.6.0 255.255.255.0 10.1.1.1
ip route 10.1.7.0 255.255.255.0 10.1.1.1
ip route 10.1.8.0 255.255.255.0 10.1.1.1
ip route 10.1.9.0 255.255.255.0 10.1.1.1
ip route 10.1.10.0 255.255.255.0 10.1.1.1
ip route 10.1.11.0 255.255.255.0 10.1.1.1
ip route 10.1.12.0 255.255.255.0 10.1.1.1
ip route 192.168.0.0 255.255.255.0 10.1.1.1
ip route 192.168.1.0 255.255.255.0 10.1.1.1
no ip http server
ip http secure-server
!Core Switch Configsh run
Building configuration...Current configuration : 10622 bytes
version 12.2
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
service compress-config
hostname Nimc_Core
boot-start-marker
boot-end-marker!
aaa new-model
aaa authentication login default local
aaa session-id common
storm-control broadcast include multicast
ip subnet-zero
no ip domain-lookup
ip domain-name nimc.gov.ng
ip dhcp excluded-address 10.1.2.1 10.1.2.10
ip dhcp excluded-address 10.1.4.1 10.1.4.10
ip dhcp excluded-address 10.1.5.1 10.1.5.10
ip dhcp excluded-address 10.1.6.1 10.1.6.10
ip dhcp excluded-address 10.1.7.1 10.1.7.10
ip dhcp excluded-address 10.1.8.1 10.1.8.10
ip dhcp excluded-address 10.1.9.1 10.1.9.10
ip dhcp excluded-address 10.1.10.1 10.1.10.10
ip dhcp excluded-address 10.1.3.1 10.1.3.10
ip dhcp pool Voice
network 10.1.2.0 255.255.255.0
next-server 10.1.2.1
option 150 ip 10.1.2.2
default-router 10.1.2.1
dns-server 83.229.88.30 193.238.28.249 4.2.2.2
ip dhcp pool SF_DGs_Office
network 10.1.3.0 255.255.255.0
domain-name nimc.gov.ng
default-router 10.1.3.1
dns-server 81.199.3.7
lease 10
ip dhcp pool Admin_Process_Fac_Mgt
network 10.1.4.0 255.255.255.0
domain-name nimc.gov.ng
default-router 10.1.4.1
dns-server 83.229.88.30 193.238.28.249 4.2.2.2
lease 10
ip dhcp pool SF_IDD
network 10.1.5.0 255.255.255.0
domain-name nimc.gov.ng
default-router 10.1.5.1
dns-server 83.229.88.30 193.238.28.249 4.2.2.2
lease 10
ip dhcp pool Finance_Fin_Inv
network 10.1.6.0 255.255.255.0
domain-name nimc.gov.ng
default-router 10.1.6.1
dns-server 83.229.88.30 193.238.28.249 4.2.2.2
lease 10
ip dhcp pool Finance_CS
network 10.1.7.0 255.255.255.0
domain-name nimc.gov.ng
default-router 10.1.7.1
dns-server 83.229.88.30 193.238.28.249 4.2.2.2
lease 10
ip dhcp pool FF_Human_Capital_Mgt
network 10.1.8.0 255.255.255.0
domain-name nimc.gov.ng
default-router 10.1.8.1
dns-server 83.229.88.30 193.238.28.249 4.2.2.2
lease 10
ip dhcp pool FF_Legal_Services
network 10.1.9.0 255.255.255.0
domain-name nimc.gov.ng
default-router 10.1.9.1
dns-server 83.229.88.30 193.238.28.249 4.2.2.2
lease 10
ip dhcp pool SF_Procurement_Serv
network 10.1.10.0 255.255.255.0
domain-name nimc.gov.ng
default-router 10.1.10.1
dns-server 83.229.88.30 193.238.28.249 4.2.2.2
lease 10
ip vrf mgmtVrf
errdisable recovery cause bpduguard
errdisable recovery interval 180
power redundancy-mode redundant
spanning-tree mode mst
spanning-tree portfast bpduguard default
spanning-tree extend system-id
spanning-tree mst configuration
name xxxx
revision 1
instance 1 vlan 1-20
spanning-tree mst 1 priority 0
spanning-tree vlan 1-20 priority 0
vlan internal allocation policy ascending
interface FastEthernet1
ip vrf forwarding mgmtVrf
no ip address
speed auto
duplex auto
interface GigabitEthernet1/1
switchport trunk encapsulation dot1q
switchport mode trunk
interface GigabitEthernet1/2
switchport access vlan 4
switchport mode access
spanning-tree portfast
interface GigabitEthernet1/3
switchport access vlan 2
switchport mode access
switchport voice vlan 4
spanning-tree portfast
interface GigabitEthernet1/4
switchport mode access
spanning-tree portfast
interface GigabitEthernet1/5
switchport access vlan 2
switchport mode access
switchport voice vlan 4
spanning-tree portfast
interface GigabitEthernet1/6
switchport access vlan 2
switchport mode access
switchport voice vlan 4
spanning-tree portfast
interface GigabitEthernet1/7
switchport access vlan 2
switchport mode access
switchport voice vlan 4
spanning-tree portfast
interface GigabitEthernet1/8
switchport access vlan 2
switchport mode access
switchport voice vlan 4
spanning-tree portfast!
interface GigabitEthernet1/9
switchport access vlan 2
switchport mode access
switchport voice vlan 4
spanning-tree portfast
interface GigabitEthernet1/10
switchport access vlan 2
switchport mode access
switchport voice vlan 4
spanning-tree portfast
interface GigabitEthernet1/11
switchport access vlan 2
switchport mode access
switchport voice vlan 4
spanning-tree portfast
interface GigabitEthernet1/12
switchport access vlan 2
switchport mode access
switchport voice vlan 4
spanning-tree portfast
interface GigabitEthernet1/13
switchport access vlan 2
switchport mode access
switchport voice vlan 4
spanning-tree portfast
interface GigabitEthernet1/14
switchport access vlan 2
switchport mode access
switchport voice vlan 4
spanning-tree portfast
interface GigabitEthernet1/15
switchport access vlan 2
switchport mode access
switchport voice vlan 4
spanning-tree portfast
interface GigabitEthernet1/16
switchport access vlan 2
switchport mode access
switchport voice vlan 4
spanning-tree portfast
interface GigabitEthernet1/17
switchport access vlan 2
switchport mode access
switchport voice vlan 4
spanning-tree portfast
interface GigabitEthernet1/18
switchport access vlan 2
switchport mode access
switchport voice vlan 4
spanning-tree portfast
interface GigabitEthernet1/19
switchport access vlan 2
switchport mode access
switchport voice vlan 4
spanning-tree portfast
interface GigabitEthernet1/20
switchport access vlan 2
switchport mode access
switchport voice vlan 4
spanning-tree portfast
interface GigabitEthernet1/21
switchport access vlan 2
switchport mode access
switchport voice vlan 4
spanning-tree portfast
interface GigabitEthernet1/22
switchport access vlan 2
switchport mode access
switchport voice vlan 4
spanning-tree portfast
interface GigabitEthernet1/23
switchport access vlan 2
switchport mode access
switchport voice vlan 4
spanning-tree portfast
interface GigabitEthernet1/24
switchport access vlan 2
switchport mode access
switchport voice vlan 4
spanning-tree portfast
interface GigabitEthernet1/25
switchport access vlan 2
switchport mode access
switchport voice vlan 4
spanning-tree portfast
interface GigabitEthernet1/26
switchport access vlan 2
switchport mode access
switchport voice vlan 4
spanning-tree portfast
interface GigabitEthernet1/27
switchport access vlan 2
switchport mode access
switchport voice vlan 4
spanning-tree portfast
interface GigabitEthernet1/28
switchport access vlan 2
switchport mode access
switchport voice vlan 4
spanning-tree portfast
interface GigabitEthernet1/29
switchport access vlan 2
switchport mode access
switchport voice vlan 4
spanning-tree portfast
interface GigabitEthernet1/30
switchport access vlan 2
switchport mode access
switchport voice vlan 4
spanning-tree portfast
interface GigabitEthernet1/31
switchport access vlan 2
switchport mode access
switchport voice vlan 4
spanning-tree portfastinterface GigabitEthernet1/32
switchport access vlan 2
switchport voice vlan 4
interface GigabitEthernet1/33
switchport mode access
interface GigabitEthernet1/34
switchport access vlan 2
switchport mode access
switchport voice vlan 4
spanning-tree portfast
interface GigabitEthernet1/35
switchport access vlan 2
switchport mode access
switchport voice vlan 4
spanning-tree portfast
interface GigabitEthernet1/36
switchport access vlan 2
switchport mode access
switchport voice vlan 4
spanning-tree portfast
interface GigabitEthernet1/37
switchport access vlan 2
switchport mode access
switchport voice vlan 4
spanning-tree portfast
interface GigabitEthernet1/38
switchport access vlan 2
switchport mode access
switchport voice vlan 4
spanning-tree portfast
interface GigabitEthernet1/39
switchport access vlan 2
switchport mode access
switchport voice vlan 4
spanning-tree portfast
interface GigabitEthernet1/40
switchport access vlan 2
switchport mode access
switchport voice vlan 4
spanning-tree portfast
interface GigabitEthernet1/41
switchport access vlan 2
switchport mode access
switchport voice vlan 4
spanning-tree portfast
interface GigabitEthernet1/42
switchport access vlan 2
switchport mode access
switchport voice vlan 4
spanning-tree portfast
interface GigabitEthernet1/43
switchport access vlan 2
switchport mode access
switchport voice vlan 4
spanning-tree portfast
interface GigabitEthernet1/44
switchport access vlan 2
switchport mode access
switchport voice vlan 4
spanning-tree portfast
interface GigabitEthernet1/45
switchport access vlan 2
switchport mode access
switchport voice vlan 4
spanning-tree portfast
interface GigabitEthernet1/46
switchport access vlan 2
switchport mode access
switchport voice vlan 4
spanning-tree portfast
interface GigabitEthernet1/47
switchport trunk encapsulation dot1q
switchport mode trunk
interface GigabitEthernet1/48
switchport trunk encapsulation dot1q
switchport mode trunk
interface Vlan1
no ip address
shutdown
interface Vlan2
description Management
ip address 10.1.1.1 255.255.255.0
interface Vlan3
description Enterprise
ip address 10.1.0.1 255.255.255.0
interface Vlan4
description Voice
ip address 10.1.2.1 255.255.255.0
interface Vlan5
description SS_DGs_Office
ip address 10.1.3.1 255.255.255.0
interface Vlan6
description Admin_Process_Fac_Management
ip address 10.1.4.1 255.255.255.0
interface Vlan7
description SF_National_Identity_Database
ip address 10.1.5.1 255.255.255.0
interface Vlan8
description Fin_Finance_Investment
ip address 10.1.6.1 255.255.255.0
interface Vlan9
description Fin_Corporate_Services
ip address 10.1.7.1 255.255.255.0
interface Vlan10
description FF_Human_Capital_Management
ip address 10.1.8.1 255.255.255.0
interface Vlan11
description FF_Legal_services
ip address 10.1.9.1 255.255.255.0
interface Vlan12
description SF_Procurement_Services
ip address 10.1.10.1 255.255.255.0
ip default-gateway 10.1.1.2
ip route 0.0.0.0 0.0.0.0 10.1.1.2
ip route 10.1.1.0 255.255.255.0 10.1.1.2
ip route 10.1.2.0 255.255.255.0 10.1.1.2
ip route 10.1.3.0 255.255.255.0 10.1.1.2
ip route 10.1.4.0 255.255.255.0 10.1.1.2
ip route 10.1.5.0 255.255.255.0 10.1.1.2
ip route 10.1.6.0 255.255.255.0 10.1.1.2
ip route 10.1.7.0 255.255.255.0 10.1.1.2
ip route 10.1.8.0 255.255.255.0 10.1.1.2
ip route 10.1.9.0 255.255.255.0 10.1.1.2
ip route 10.1.10.0 255.255.255.0 10.1.1.2
ip route 10.1.11.0 255.255.255.0 10.1.1.2
ip http server
--More--
control-plane
line con 0
stopbits 1
line vty 0 4
end
Please i need somebody to help meI wouldn't configure an ip address on the service engine subinterface.
Try setting up a vlan interface on the router with that ip address and the subinterface will be linked to the vlan interface through the encapsulation command. A vlan interface will better work as a gateway for the wireless clients
Nicolas -
Cisco wireless controller and AP-binding domain how do you integrate wireless domain authentication?
With Cisco equipment wlc 2500 and AP 1600 combines windows 2008 r2 domain controller to achieve the following purposes,
1, all cell phones and laptops can access the wireless network with a domain user authentication.
2, the guest network should how to do it?
My idea is:
Made a total of two ssid below
Mobile users cnnewcity_mobile: Use webportal certification, so the center certification, local forwarding
Computer users cnnewcity_wifi: transparent certification, local forwarding, local authentication
The basic steps are as follows:
1, set the Radius server clients (AP or controller)
2, locking authorization group --- this should be based on the domain user group authorization radius server
3, the mobile roaming - different locations on the DHCP server choose to do this you have to consider the next 43
4, the establishment of a two vlan to a mobile user to the computer user, create a DCHP scope on the DHCP
I do not know if you have wood there are better ways?Integrating the AD to the WLC Requires:
1. AD to be registered:
AT: Security->AAA
AT: LDAP
CLICK: New
Server IP: <AD IP>
Port Number: 389
Simple Bind: Authenticated
Bind User: CN=Administrator,CN=Users,DC=testing,DC=local,DC=com
Bind Pass: <LDAP Admin pass>
Confirm Pass: <LDAP Admin pass>
User Base DN: OU=WebAuth_Users,DC=testing,DC=local,DC=com
User Attrib: sAMAccountName
User Obj. Type: person
Enable at WLAN Profile
1. AT: WLAN->WLANs
CLICK: <Desired WLAN> -typically web authentication
2. AT: Security Tab
AT: AAA Servers
3. AT: LDAP Servers
**Select Created LDAP
4. Apply to Save
Source: Tried it in implementations :)) -
Wireless Network is slow after putting cisco wireless controller
Hello Guys,
My wireless network was very good before putting Cisco WLC 4402 with version 3.2.171.6.
In my network there are two SSID's one for official and another for guest, which is working one single LAP 1142.( Total 12 LWAP is here)
we decided to manage all the ap and deployed WLC but now wireless network is very slow, local gateways is pinging with 80 ms. before WLC it was 1 ms.
Pls. suggest or come up with question to reach a solution.
reg
sanjeevHi,
yah it's gigabit support and i have connected with fibre patch cord.
My SWITCH port config is below.
interface GigabitEthernet1/0/25
switchport trunk encapsulation dot1q
switchport mode trunk
Controller sh run
System Inventory
Switch Description............................... Cisco Controller
Machine Model.................................... AIR-WLC4402-12-K9
Serial Number.................................... FOC1105F01E
Burned-in MAC Address............................ 00:1A:6D:DD:23:00
Crypto Accelerator 1............................. Absent
Crypto Accelerator 2............................. Absent
Power Supply 1................................... Absent
Power Supply 2................................... Present, OK
Press Enter to continue Or to abort
System Information
Manufacturer's Name.............................. Cisco Systems, Inc
Product Name..................................... Cisco Controller
Product Version.................................. 3.2.171.6
RTOS Version..................................... 3.2.171.6
Bootloader Version............................... 3.2.171.6
Build Type....................................... DATA + WPS
System Name...................................... SFA-CTRL2-HQ
System Location..................................
System Contact...................................
System ObjectID.................................. 1.3.6.1.4.1.14179.1.1.4.3
IP Address....................................... 10.156.11.231
System Up Time................................... 0 days 11 hrs 9 mins 43 secs
Configured Country............................... United States
Operating Environment............................ Commercial (0 to 40 C)
Internal Temp Alarm Limits....................... 0 to 65 C
Internal Temperature............................. +38 C
State of 802.11b Network......................... Enabled
State of 802.11a Network......................... Enabled
Number of WLANs.................................. 4
3rd Party Access Point Support................... Disabled
Number of Active Clients......................... 115
Press Enter to continue Or to abort
Switch Configuration
802.3x Flow Control Mode......................... Disable
Current LWAPP Transport Mode..................... Layer 3
LWAPP Transport Mode after next switch reboot.... Layer 3
FIPS prerequisite features....................... Disabled
Press Enter to continue Or to abort
Network Information
RF-Network Name............................. UNISFA
Web Mode.................................... Enable
Secure Web Mode............................. Enable
Secure Shell (ssh).......................... Enable
Telnet...................................... Enable
Ethernet Multicast Mode..................... Disable Mode: Ucast
User Idle Timeout........................... 300 seconds
ARP Idle Timeout............................ 300 seconds
ARP Unicast Mode............................ Disabled
Cisco AP Default Master..................... Disable
Mgmt Via Wireless Interface................. Enable
Bridge AP Zero Config....................... Enable
Bridge Shared Secret........................ youshouldsetme
Allow Old Bridging Aps To Authenticate...... Enable
Over The Air Provisioning of AP's........... Enable
Mobile Peer to Peer Blocking................ Disable
Apple Talk ................................. Disable
AP Fallback ................................ Enable
Web Auth Redirect Ports .................... 80
Fast SSID Change ........................... Disabled
Press Enter to continue Or to abort
Port Summary
STP Admin Physical Physical Link Link Mcast
Pr Type Stat Mode Mode Status Status Trap Appliance POE
1 Normal Forw Enable Auto 1000 Full Up Enable Enable N/A
2 Normal Disa Enable Auto 1000 Full Down Enable Enable N/A
Press Enter to continue Or to abort
AP Summary
AP Name Slots AP Model Ethernet MAC Location Port
AP_MHQ_CMS_OFFICE 2 AIR-LAP1242AG-A-K9 00:19:30:76:75:42 default location 1
AP01-MHQ-HOM 2 AIR-LAP1242AG-A-K9 00:19:30:76:74:be default location 1
AP01_MHQ_AIROPS 2 AIR-LAP1242AG-A-K9 00:1d:45:36:6c:84 default location 1
AP01_MSA_HOM_RES 2 AIR-LAP1242AG-A-K9 00:1d:45:36:6b:e2 default location 1
AP10-MHQ-CCITS 2 AIR-LAP1242AG-A-K9 00:19:30:76:74:82 default location 1
AP01-MSA2-TC5 2 AIR-LAP1242AG-A-K9 00:1d:45:36:6d:44 default location 1
AP01_MSA_CableTV_Room 2 AIR-LAP1242AG-A-K9 00:19:30:76:83:aa default location 1
AP01_MSA_RUS_ROOM 2 AIR-LAP1242AG-A-K9 00:19:30:76:83:00 default location 1
AP01-MHQ-JLOC 2 AIR-LAP1242AG-A-K9 00:19:30:76:7f:d0 default location 1
AP01-MSA-C2-D 2 AIR-LAP1242AG-A-K9 00:19:30:76:74:90 default location 1
AP01_MSA_DA7 2 AIR-LAP1242AG-A-K9 00:19:30:76:80:38 default location 1
AP01_MSA_CMS_RES 2 AIR-LAP1242AG-A-K9 00:19:30:76:83:f0 default location 1
Press Enter to continue Or to abort
AP Config
Cisco AP Identifier.............................. 1
Cisco AP Name.................................... AP_MHQ_CMS_OFFICE
AP Regulatory Domain............................. -A
Switch Port Number .............................. 1
MAC Address...................................... 00:19:30:76:75:42
IP Address Configuration......................... Static IP assigned
IP Address....................................... 10.156.11.240
IP NetMask....................................... 255.255.254.0
Gateway IP Addr.................................. 10.156.10.1
Cisco AP Location................................ default location
Cisco AP Group Name.............................. default-group
Primary Cisco Switch.............................
Secondary Cisco Switch...........................
Tertiary Cisco Switch............................
Administrative State ............................ ADMIN_ENABLED
Operation State ................................. REGISTERED
Mirroring Mode .................................. Disabled
AP Mode ......................................... Local
Remote AP Debug ................................. Disabled
S/W Version .................................... 3.2.171.6
Boot Version ................................... 12.3.7.1
Mini IOS Version ................................ 3.0.51.0
Stats Reporting Period .......................... 180
LED State........................................ Enabled
PoE Pre-Standard Switch.......................... Disabled
PoE Power Injector MAC Addr...................... Disabled
Number Of Slots.................................. 2
AP Model......................................... AIR-LAP1242AG-A-K9
IOS Version...................................... 12.3(7)JX6
Reset Button..................................... Enabled
AP Serial Number................................. FTX1107B3U8
AP Certificate Type.............................. Manufacture Installed
Attributes for Slot 0
Radio Type................................... RADIO_TYPE_80211g
Administrative State ........................ ADMIN_ENABLED
Operation State ............................. UP
WLAN Override ............................... Disabled
CellId ...................................... 0
Station Configuration
Configuration ............................. AUTOMATIC
Number Of WLANs ........................... 2
Medium Occupancy Limit .................... 100
CFP Period ................................ 4
CFP MaxDuration ........................... 60
BSSID ..................................... 00:1a:a2:d9:d3:60
Operation Rate Set
1000 Kilo Bits........................... MANDATORY
2000 Kilo Bits........................... MANDATORY
5500 Kilo Bits........................... MANDATORY
11000 Kilo Bits.......................... MANDATORY
6000 Kilo Bits........................... SUPPORTED
9000 Kilo Bits........................... SUPPORTED
12000 Kilo Bits.......................... SUPPORTED
18000 Kilo Bits.......................... SUPPORTED
24000 Kilo Bits.......................... SUPPORTED
36000 Kilo Bits.......................... SUPPORTED
48000 Kilo Bits.......................... SUPPORTED
54000 Kilo Bits.......................... SUPPORTED
Beacon Period ............................. 100
DTIM Period ............................... 1
Fragmentation Threshold ................... 2346
Multi Domain Capability Implemented ....... TRUE
Multi Domain Capability Enabled ........... TRUE
Country String ............................ US
Multi Domain Capability
Configuration ............................. AUTOMATIC
First Chan Num ............................ 1
Number Of Channels ........................ 11
MAC Operation Parameters
Configuration ............................. AUTOMATIC
RTS Threshold ............................. 2347
Short Retry Limit ......................... 7
Long Retry Limit .......................... 4
Fragmentation Threshold ................... 2346
Maximum Tx MSDU Life Time ................. 512
Maximum Rx Life Time ...................... 512
Tx Power
Num Of Supported Power Levels ............. 8
Tx Power Level 1 .......................... 20 dBm
Tx Power Level 2 .......................... 17 dBm
Tx Power Level 3 .......................... 14 dBm
Tx Power Level 4 .......................... 11 dBm
Tx Power Level 5 .......................... 8 dBm
Tx Power Level 6 .......................... 5 dBm
Tx Power Level 7 .......................... 2 dBm
Tx Power Level 8 .......................... -1 dBm
Tx Power Configuration .................... AUTOMATIC
Current Tx Power Level .................... 1
Phy OFDM parameters
Configuration ............................. AUTOMATIC
Current Channel ........................... 1
TI Threshold .............................. -50
Antenna Type............................... EXTERNAL_ANTENNA
External Antenna Gain (in .5 dBm units).... 0
Diversity.................................. DIVERSITY_ENABLED
Performance Profile Parameters
Configuration ............................. AUTOMATIC
Interference threshold..................... 10 %
Noise threshold............................ -70 dBm
RF utilization threshold................... 80 %
Data-rate threshold........................ 1000000 bps
Client threshold........................... 12 clients
Coverage SNR threshold..................... 12 dB
Coverage exception level................... 25 %
Client minimum exception level............. 3 clients
Rogue Containment Information
Containment Count............................ 0
Cisco AP Identifier.............................. 1
Cisco AP Name.................................... AP_MHQ_CMS_OFFICE
AP Regulatory Domain............................. -A
Switch Port Number .............................. 1
MAC Address...................................... 00:19:30:76:75:42
IP Address Configuration......................... Static IP assigned
IP Address....................................... 10.156.11.240
IP NetMask....................................... 255.255.254.0
Gateway IP Addr.................................. 10.156.10.1
Cisco AP Location................................ default location
Cisco AP Group Name.............................. default-group
Primary Cisco Switch.............................
Secondary Cisco Switch...........................
Tertiary Cisco Switch............................
Administrative State ............................ ADMIN_ENABLED
Operation State ................................. REGISTERED
Mirroring Mode .................................. Disabled
AP Mode ......................................... Local
Remote AP Debug ................................. Disabled
S/W Version .................................... 3.2.171.6
Boot Version ................................... 12.3.7.1
Mini IOS Version ................................ 3.0.51.0
Stats Reporting Period .......................... 180
LED State........................................ Enabled
PoE Pre-Standard Switch.......................... Disabled
PoE Power Injector MAC Addr...................... Disabled
Number Of Slots.................................. 2
AP Model......................................... AIR-LAP1242AG-A-K9
IOS Version...................................... 12.3(7)JX6
Reset Button..................................... Enabled
AP Serial Number................................. FTX1107B3U8
AP Certificate Type.............................. Manufacture Installed
Attributes for Slot 1
Radio Type................................... RADIO_TYPE_80211a
Administrative State ........................ ADMIN_ENABLED
Operation State ............................. UP
WLAN Override ............................... Disabled
CellId ...................................... 0
Station Configuration
Configuration ............................. AUTOMATIC
Number Of WLANs ........................... 2
Medium Occupancy Limit .................... 100
CFP Period ................................ 4
CFP MaxDuration ........................... 60
BSSID ..................................... 00:1a:a2:d9:d3:60
Operation Rate Set
6000 Kilo Bits........................... MANDATORY
9000 Kilo Bits........................... MANDATORY
12000 Kilo Bits.......................... MANDATORY
18000 Kilo Bits.......................... SUPPORTED
24000 Kilo Bits.......................... SUPPORTED
36000 Kilo Bits.......................... SUPPORTED
48000 Kilo Bits.......................... SUPPORTED
54000 Kilo Bits.......................... SUPPORTED
Beacon Period ............................. 100
DTIM Period ............................... 1
Fragmentation Threshold ................... 2346
Multi Domain Capability Implemented ....... TRUE
Multi Domain Capability Enabled ........... TRUE
Country String ............................ US
Multi Domain Capability
Configuration ............................. AUTOMATIC
First Chan Num ............................ 36
Number Of Channels ........................ 4
MAC Operation Parameters
Configuration ............................. AUTOMATIC
RTS Threshold ............................. 2347
Short Retry Limit ......................... 7
Long Retry Limit .......................... 4
Fragmentation Threshold ................... 2346
Maximum Tx MSDU Life Time ................. 512
Maximum Rx Life Time ...................... 512
Tx Power
Num Of Supported Power Levels ............. 8
Tx Power Level 1 .......................... 17 dBm
Tx Power Level 2 .......................... 15 dBm
Tx Power Level 3 .......................... 14 dBm
Tx Power Level 4 .......................... 11 dBm
Tx Power Level 5 .......................... 8 dBm
Tx Power Level 6 .......................... 5 dBm
Tx Power Level 7 .......................... 2 dBm
Tx Power Level 8 .......................... -1 dBm
Tx Power Configuration .................... AUTOMATIC
Current Tx Power Level .................... 1
Phy OFDM parameters
Configuration ............................. AUTOMATIC
Current Channel ........................... 36
TI Threshold .............................. -50
Antenna Type............................... EXTERNAL_ANTENNA
External Antenna Gain (in .5 dBm units).... 24
Diversity.................................. DIVERSITY_ENABLED
Performance Profile Parameters
Configuration ............................. AUTOMATIC
Interference threshold..................... 10 %
Noise threshold............................ -70 dBm
RF utilization threshold................... 80 %
Data-rate threshold........................ 1000000 bps
Client threshold........................... 12 clients
Coverage SNR threshold..................... 16 dB
Coverage exception level................... 25 %
Client minimum exception level............. 3 clients
Rogue Containment Information
Containment Count............................ 0
Cisco AP Identifier.............................. 2
Cisco AP Name.................................... AP01-MHQ-HOM
AP Regulatory Domain............................. -A
Switch Port Number .............................. 1
MAC Address...................................... 00:19:30:76:74:be
IP Address Configuration......................... Static IP assigned
IP Address....................................... 10.156.11.238
IP NetMask....................................... 255.255.254.0
Gateway IP Addr.................................. 10.156.10.1
Cisco AP Location................................ default location
Cisco AP Group Name.............................. default-group
Primary Cisco Switch.............................
Secondary Cisco Switch...........................
Tertiary Cisco Switch............................
Administrative State ............................ ADMIN_ENABLED
Operation State ................................. REGISTERED
Mirroring Mode .................................. Disabled
AP Mode ......................................... Local
Remote AP Debug ................................. Disabled
S/W Version .................................... 3.2.171.6
Boot Version ................................... 12.3.7.1
Mini IOS Version ................................ 3.0.51.0
Stats Reporting Period .......................... 180
LED State........................................ Enabled
PoE Pre-Standard Switch.......................... Disabled
PoE Power Injector MAC Addr...................... Disabled
Number Of Slots.................................. 2
AP Model......................................... AIR-LAP1242AG-A-K9
IOS Version...................................... 12.3(7)JX6
Reset Button..................................... Enabled
AP Serial Number................................. FTX1107B3W4
AP Certificate Type.............................. Manufacture Installed
Attributes for Slot 0
Radio Type................................... RADIO_TYPE_80211g
Administrative State ........................ ADMIN_ENABLED
Operation State ............................. UP
WLAN Override ............................... Disabled
CellId ...................................... 0
Station Configuration
Configuration ............................. AUTOMATIC
Number Of WLANs ........................... 2
Medium Occupancy Limit .................... 100
CFP Period ................................ 4
CFP MaxDuration ........................... 60
BSSID ..................................... 00:1a:30:e7:fc:30
Operation Rate Set
1000 Kilo Bits........................... MANDATORY
2000 Kilo Bits........................... MANDATORY
5500 Kilo Bits........................... MANDATORY
11000 Kilo Bits.......................... MANDATORY
6000 Kilo Bits........................... SUPPORTED
9000 Kilo Bits........................... SUPPORTED
12000 Kilo Bits.......................... SUPPORTED
18000 Kilo Bits.......................... SUPPORTED
24000 Kilo Bits.......................... SUPPORTED
36000 Kilo Bits.......................... SUPPORTED
48000 Kilo Bits.......................... SUPPORTED
54000 Kilo Bits.......................... SUPPORTED
Beacon Period ............................. 100
DTIM Period ............................... 1
Fragmentation Threshold ................... 2346
Multi Domain Capability Implemented ....... TRUE
Multi Domain Capability Enabled ........... TRUE
Country String ............................ US
Multi Domain Capability
Configuration ............................. AUTOMATIC
First Chan Num ............................ 1
Number Of Channels ........................ 11
MAC Operation Parameters
Configuration ............................. AUTOMATIC
RTS Threshold ............................. 2347
Short Retry Limit ......................... 7
Long Retry Limit .......................... 4
Fragmentation Threshold ................... 2346
Maximum Tx MSDU Life Time ................. 512
Maximum Rx Life Time ...................... 512
Tx Power
Num Of Supported Power Levels ............. 8
Tx Power Level 1 .......................... 20 dBm
Tx Power Level 2 .......................... 17 dBm
Tx Power Level 3 .......................... 14 dBm
Tx Power Level 4 .......................... 11 dBm
Tx Power Level 5 .......................... 8 dBm
Tx Power Level 6 .......................... 5 dBm
Tx Power Level 7 .......................... 2 dBm
Tx Power Level 8 .......................... -1 dBm
Tx Power Configuration .................... AUTOMATIC
Current Tx Power Level .................... 2
Phy OFDM parameters
Configuration ............................. AUTOMATIC
Current Channel ........................... 11
TI Threshold .............................. -50
Antenna Type............................... EXTERNAL_ANTENNA
External Antenna Gain (in .5 dBm units).... 0
Diversity.................................. Side A or Right Connector
Performance Profile Parameters
Configuration ............................. AUTOMATIC
Interference threshold..................... 10 %
Noise threshold............................ -70 dBm
RF utilization threshold................... 80 %
Data-rate threshold........................ 1000000 bps
Client threshold........................... 12 clients
Coverage SNR threshold..................... 12 dB
Coverage exception level................... 25 %
Client minimum exception level............. 3 clients
Rogue Containment Information
Containment Count............................ 0
Cisco AP Identifier.............................. 2
Cisco AP Name.................................... AP01-MHQ-HOM
AP Regulatory Domain............................. -A
Switch Port Number .............................. 1
MAC Address...................................... 00:19:30:76:74:be
IP Address Configuration......................... Static IP assigned
IP Address....................................... 10.156.11.238
IP NetMask....................................... 255.255.254.0
Gateway IP Addr.................................. 10.156.10.1
Cisco AP Location................................ default location
Cisco AP Group Name.............................. default-group
Primary Cisco Switch.............................
Secondary Cisco Switch...........................
Tertiary Cisco Switch............................
Administrative State ............................ ADMIN_ENABLED
Operation State ................................. REGISTERED
Mirroring Mode .................................. Disabled
AP Mode ......................................... Local
Remote AP Debug ................................. Disabled
S/W Version .................................... 3.2.171.6
Boot Version ................................... 12.3.7.1
Mini IOS Version ................................ 3.0.51.0
Stats Reporting Period .......................... 180
LED State........................................ Enabled
PoE Pre-Standard Switch.......................... Disabled
PoE Power Injector MAC Addr...................... Disabled
Number Of Slots.................................. 2
AP Model......................................... AIR-LAP1242AG-A-K9
IOS Version...................................... 12.3(7)JX6
Reset Button..................................... Enabled
AP Serial Number................................. FTX1107B3W4
AP Certificate Type.............................. Manufacture Installed
Attributes for Slot 1
Radio Type................................... RADIO_TYPE_80211a
Administrative State ........................ ADMIN_ENABLED
Operation State ............................. UP
WLAN Override ............................... Disabled
CellId ...................................... 0
Station Configuration
Configuration ............................. AUTOMATIC
Number Of WLANs ........................... 2
Medium Occupancy Limit .................... 100
CFP Period ................................ 4
CFP MaxDuration ........................... 60
BSSID ..................................... 00:1a:30:e7:fc:30
Operation Rate Set
6000 Kilo Bits........................... MANDATORY
9000 Kilo Bits........................... MANDATORY
12000 Kilo Bits.......................... MANDATORY
18000 Kilo Bits.......................... SUPPORTED
24000 Kilo Bits.......................... SUPPORTED
36000 Kilo Bits.......................... SUPPORTED
48000 Kilo Bits.......................... SUPPORTED
54000 Kilo Bits.......................... SUPPORTED
Beacon Period ............................. 100
DTIM Period ............................... 1
Fragmentation Threshold ................... 2346
Multi Domain Capability Implemented ....... TRUE
Multi Domain Capability Enabled ........... TRUE
Country String ............................ US
Multi Domain Capability
Configuration ............................. AUTOMATIC
First Chan Num ............................ 36
Number Of Channels ........................ 4
MAC Operation Parameters
Configuration ............................. AUTOMATIC
RTS Threshold ............................. 2347
Short Retry Limit ......................... 7
Long Retry Limit .......................... 4
Fragmentation Threshold ................... 2346
Maximum Tx MSDU Life Time ................. 512
Maximum Rx Life Time ...................... 512
Tx Power
Num Of Supported Power Levels ............. 8
Tx Power Level 1 .......................... 17 dBm
Tx Power Level 2 .......................... 15 dBm
Tx Power Level 3 .......................... 14 dBm
Tx Power Level 4 .......................... 11 dBm
Tx Power Level 5 .......................... 8 dBm
Tx Power Level 6 .......................... 5 dBm
Tx Power Level 7 .......................... 2 dBm
Tx Power Level 8 .......................... -1 dBm
Tx Power Configuration .................... AUTOMATIC
Current Tx Power Level .................... 1
Phy OFDM parameters
Configuration ............................. AUTOMATIC
Current Channel ........................... 36
TI Threshold .............................. -50
Antenna Type............................... EXTERNAL_ANTENNA
External Antenna Gain (in .5 dBm units).... 0
Diversity.................................. DIVERSITY_ENABLED
Performance Profile Parameters
Configuration ............................. AUTOMATIC
Interference threshold..................... 10 %
Noise threshold............................ -70 dBm
RF utilization threshold................... 80 %
Data-rate threshold........................ 1000000 bps
Client threshold........................... 12 clients
Coverage SNR threshold..................... 16 dB
Coverage exception level................... 25 %
Client minimum exception level............. 3 clients
Rogue Containment Information
Containment Count............................ 0
Cisco AP Identifier.............................. 3
Cisco AP Name.................................... AP01_MHQ_AIROPS
AP Regulatory Domain............................. -A
Switch Port Number .............................. 1
MAC Address...................................... 00:1d:45:36:6c:84
IP Address Configuration......................... Static IP assigned
IP Address....................................... 10.156.11.232
IP NetMask....................................... 255.255.254.0
Gateway IP Addr.................................. 10.156.10.1
Cisco AP Location................................ default location
Cisco AP Group Name.............................. default-group
Primary Cisco Switch.............................
Secondary Cisco Switch...........................
Tertiary Cisco Switch............................
Administrative State ............................ ADMIN_ENABLED
Operation State ................................. REGISTERED
Mirroring Mode .................................. Disabled
AP Mode ......................................... Local
Remote AP Debug ................................. Disabled
S/W Version .................................... 3.2.171.6
Boot Version ................................... 12.3.7.1
Mini IOS Version ................................ 3.0.51.0
Stats Reporting Period .......................... 180
LED State........................................ Enabled
PoE Pre-Standard Switch.......................... Disabled
PoE Power Injector MAC Addr...................... Disabled
Number Of Slots.................................. 2
AP Model......................................... AIR-LAP1242AG-A-K9
IOS Version...................................... 12.3(7)JX6
Reset Button..................................... Enabled
AP Serial Number................................. FTX1135B2X7
AP Certificate Type.............................. Manufacture Installed
Attributes for Slot 0
Radio Type................................... RADIO_TYPE_80211g
Administrative State ........................ ADMIN_ENABLED
Operation State ............................. UP
WLAN Override ............................... Disabled
CellId ...................................... 0
Station Configuration
Configuration ............................. AUTOMATIC
Number Of WLANs ........................... 2
Medium Occupancy Limit .................... 100
CFP Period ................................ 4
CFP MaxDuration ........................... 60
BSSID ..................................... 00:1d:46:7e:d9:60
Operation Rate Set
1000 Kilo Bits........................... MANDATORY
2000 Kilo Bits........................... MANDATORY
5500 Kilo Bits........................... MANDATORY
11000 Kilo Bits.......................... MANDATORY
6000 Kilo Bits........................... SUPPORTED
9000 Kilo Bits........................... SUPPORTED
12000 Kilo Bits.......................... SUPPORTED
18000 Kilo Bits.......................... SUPPORTED
24000 Kilo Bits.......................... SUPPORTED
36000 Kilo Bits.......................... SUPPORTED
48000 Kilo Bits.......................... SUPPORTED
54000 Kilo Bits.......................... SUPPORTED
Beacon Period ............................. 100
DTIM Period ............................... 1
Fragmentation Threshold ................... 2346
Multi Domain Capability Implemented ....... TRUE
Multi Domain Capability Enabled ........... TRUE
Country String ............................ US
Multi Domain Capability
Configuration ............................. AUTOMATIC
First Chan Num ............................ 1
Number Of Channels ........................ 11
MAC Operation Parameters
Configuration ............................. AUTOMATIC
RTS Threshold ............................. 2347
Short Retry Limit ......................... 7
Long Retry Limit .......................... 4
Fragmentation Threshold ................... 2346
Maximum Tx MSDU Life Time ................. 512
Maximum Rx Life Time ...................... 512
Tx Power
Num Of Supported Power Levels ............. 8
Tx Power Level 1 .......................... 20 dBm
Tx Power Level 2 .......................... 17 dBm
Tx Power Level 3 .......................... 14 dBm
Tx Power Level 4 .......................... 11 dBm
Tx Power Level 5 .......................... 8 dBm
Tx Power Level 6 .......................... 5 dBm
Tx Power Level 7 .......................... 2 dBm
Tx Power Level 8 .......................... -1 dBm
Tx Power Configuration .................... AUTOMATIC
Current Tx Power Level .................... 1
Phy OFDM parameters
Configuration ............................. AUTOMATIC
Current Channel ........................... 6
TI Threshold .............................. -50
Antenna Type............................... EXTERNAL_ANTENNA
External Antenna Gain (in .5 dBm units).... 0
Diversity.................................. Side A or Right Connector
Performance Profile Parameters
Configuration ............................. AUTOMATIC
Interference threshold..................... 10 %
Noise threshold............................ -70 dBm
RF utilization threshold................... 80 %
Data-rate threshold........................ 1000000 bps
Client threshold........................... 12 clients
Coverage SNR threshold..................... 12 dB
Coverage exception level................... 25 %
Client minimum exception level............. 3 clients
Rogue Containment Information
Containment Count............................ 0
Cisco AP Identifier.............................. 3
Cisco AP Name.................................... AP01_MHQ_AIROPS
AP Regulatory Domain............................. -A
Switch Port Number .............................. 1
MAC Address...................................... 00:1d:45:36:6c:84
IP Address Configuration......................... Static IP assigned
IP Address....................................... 10.156.11.232
IP NetMask....................................... 255.255.254.0
Gateway IP Addr.................................. 10.156.10.1
Cisco AP Location................................ default location
Cisco AP Group Name.............................. default-group
Primary Cisco Switch.............................
Secondary Cisco Switch...........................
Tertiary Cisco Switch............................
Administrative State ............................ ADMIN_ENABLED
Operation State ................................. REGISTERED
Mirroring Mode .................................. Disabled
AP Mode ......................................... Local
Remote AP Debug ................................. Disabled
S/W Version .................................... 3.2.171.6
Boot Version ................................... 12.3.7.1
Mini IOS Version ................................ 3.0.51.0
Stats Reporting Period .......................... 180
LED State........................................ Enabled
PoE Pre-Standard Switch.......................... Disabled
PoE Power Injector MAC Addr...................... Disabled
Number Of Slots.................................. 2
AP Model......................................... AIR-LAP1242AG-A-K9
IOS Version...................................... 12.3(7)JX6
Reset Button..................................... Enabled
AP Serial Number................................. FTX1135B2X7
AP Certificate Type.............................. Manufacture Installed
Attributes for Slot 1
Radio Type................................... RADIO_TYPE_80211a
Administrative State ........................ ADMIN_ENABLED
Operation State ............................. UP
WLAN Override ............................... Disabled
CellId ...................................... 0
Station Configuration
Configuration ............................. AUTOMATIC
Number Of WLANs ........................... 2
Medium Occupancy Limit .................... 100
CFP Period ................................ 4
CFP MaxDuration ........................... 60
BSSID ..................................... 00:1d:46:7e:d9:60
Operation Rate Set
6000 Kilo Bits........................... MANDATORY
9000 Kilo Bits........................... MANDATORY
12000 Kilo Bits.......................... MANDATORY
18000 Kilo Bits.......................... SUPPORTED
24000 Kilo Bits.......................... SUPPORTED
36000 Kilo Bits.......................... SUPPORTED
48000 Kilo Bits.......................... SUPPORTED
54000 Kilo Bits.......................... SUPPORTED
Beacon Period ............................. 100
DTIM Period ............................... 1
Fragmentation Threshold ................... 2346
Multi Domain Capability Implemented ....... TRUE
Multi Domain Capability Enabled ........... TRUE
Country String ............................ US
Multi Domain Capability
Configuration ............................. AUTOMATIC
First Chan Num ............................ 36
Number Of Channels ........................ 4
MAC Operation Parameters
Configuration ............................. AUTOMATIC
RTS Threshold ............................. 2347
Short Retry Limit ......................... 7
Long Retry Limit .......................... 4
Fragmentation Threshold ................... 2346
Maximum Tx MSDU Life Time ................. 512
Maximum Rx Life Time ...................... 512
Tx Power
Num Of Supported Power Levels ............. 8
Tx Power Level 1 .......................... 17 dBm
Tx Power Level 2 .......................... 15 dBm
Tx Power Level 3 .......................... 14 dBm
Tx Power Level 4 .......................... 11 dBm
Tx Power Level 5 .......................... 8 dBm
Tx Power Level 6 .......................... 5 dBm
Tx Power Level 7 .......................... 2 dBm
Tx Power Level 8 .......................... -1 dBm
Tx Power Configuration .................... AUTOMATIC
Current Tx Power Level .................... 1
Phy OFDM parameters
Configuration ............................. AUTOMATIC
Current Channel ........................... 36
TI Threshold .............................. -50
Antenna Type............................... EXTERNAL_ANTENNA
External Antenna Gain (in .5 dBm units).... 0
Diversity.................................. DIVERSITY_ENABLED
Performance Profile Parameters
Configuration ............................. AUTOMATIC
Interference threshold..................... 10 %
Noise threshold............................ -70 dBm
RF utilization threshold................... 80 %
Data-rate threshold........................ 1000000 bps
Client threshold........................... 12 clients
Coverage SNR threshold..................... 16 dB
Coverage exception level................... 25 %
Client minimum exception level............. 3 clients
Rogue Containment Information
Containment Count............................ 0
Cisco AP Identifier.............................. 4
Cisco AP Name.................................... AP01_MSA_HOM_RES
AP Regulatory Domain............................. -A
Switch Port Number .............................. 1
MAC Address...................................... 00:1d:45:36:6b:e2
IP Address Configuration......................... Static IP assigned
IP Address....................................... 10.156.11.239
IP NetMask....................................... 255.255.254.0
Gateway IP Addr.................................. 10.156.10.1
Cisco AP Location................................ default location
Cisco AP Group Name.............................. default-group
Primary Cisco Switch.............................
Secondary Cisco Switch...........................
Tertiary Cisco Switch............................
Administrative State ............................ ADMIN_ENABLED
Operation State ................................. REGISTERED
Mirroring Mode .................................. Disabled
AP Mode ......................................... Local
Remote AP Debug ................................. Disabled
S/W Version .................................... 3.2.171.6
Boot Version ................................... 12.3.7.1
Mini IOS Version ................................ 3.0.51.0
Stats Reporting Period .......................... 180
LED State........................................ Enabled
PoE Pre-Standard Switch.......................... Disabled
PoE Power Injector MAC Addr...................... Disabled
Number Of Slots.................................. 2
AP Model......................................... AIR-LAP1242AG-A-K9
IOS Version...................................... 12.3(7)JX6
Reset Button..................................... Enabled
AP Serial Number................................. FTX1135B2X1
AP Certificate Type.............................. Manufacture Installed
Attributes for Slot 0
Radio Type................................... RADIO_TYPE_80211g
Administrative State ........................ ADMIN_ENABLED
Operation State ............................. UP
WLAN Override ............................... Disabled
CellId ...................................... 0
Station Configuration
Configuration ............................. AUTOMATIC
Number Of WLANs ........................... 2
Medium Occupancy Limit .................... 100
CFP Period ................................ 4
CFP MaxDuration ........................... 60
BSSID ..................................... 00:1d:46:7e:d4:30
Operation Rate Set
1000 Kilo Bits........................... MANDATORY
2000 Kilo Bits........................... MANDATORY
5500 Kilo Bits........................... MANDATORY
11000 Kilo Bits.......................... MANDATORY
6000 Kilo Bits........................... SUPPORTED
9000 Kilo Bits........................... SUPPORTED
12000 Kilo Bits.......................... SUPPORTED
18000 Kilo Bits.......................... SUPPORTED
24000 Kilo Bits.......................... SUPPORTED
36000 Kilo Bits.......................... SUPPORTED
48000 Kilo Bits.......................... SUPPORTED
54000 Kilo Bits.......................... SUPPORTED
Beacon Period ............................. 100
DTIM Period ............................... 1
Fragmentation Threshold ................... 2346
Multi Domain Capability Implemented ....... TRUE
Multi Domain Capability Enabled ........... TRUE
Country String ............................ US
Multi Domain Capability
Configuration ............................. AUTOMATIC
First Chan Num ............................ 1
Number Of Channels ........................ 11
MAC Operation Parameters
Configuration ............................. AUTOMATIC
RTS Threshold ............................. 2347
Short Retry Limit ......................... 7
Long Retry Limit .......................... 4
Fragmentation Threshold ................... 2346
Maximum Tx MSDU Life Time ................. 512
Maximum Rx Life Time ...................... 512
Tx Power
Num Of Supported Power Levels ............. 8
Tx Power Level 1 .......................... 20 dBm
Tx Power Level 2 .......................... 17 dBm
Tx Power Level 3 .......................... 14 dBm
Tx Power Level 4 .......................... 11 dBm
Tx Power Level 5 .......................... 8 dBm
Tx Power Level 6 .......................... 5 dBm
Tx Power Level 7 .......................... 2 dBm
Tx Power Level 8 .......................... -1 dBm
Tx Power Configuration .................... AUTOMATIC
Current Tx Power Level .................... 1
Phy OFDM parameters
Configuration ............................. AUTOMATIC
Current Channel ........................... 11
TI Threshold .............................. -50
Antenna Type............................... EXTERNAL_ANTENNA
External Antenna Gain (in .5 dBm units).... 0
Diversity.................................. DIVERSITY_ENABLED
Performance Profile Parameters
Configuration ............................. AUTOMATIC
Interference threshold..................... 10 %
Noise threshold............................ -70 dBm
RF utilization threshold................... 80 %
Data-rate threshold........................ 1000000 bps
Client threshold........................... 12 clients
Coverage SNR threshold..................... 12 dB
Coverage exception level................... 25 %
Client minimum exception level............. 3 clients
Rogue Containment Information
Containment Count............................ 0
Cisco AP Identifier.............................. 4
Cisco AP Name.................................... AP01_MSA_HOM_RES
AP Regulatory Domain............................. -A
Switch Port Number .............................. 1
MAC Address...................................... 00:1d:45:36:6b:e2
IP Address Configuration......................... Static IP assigned
IP Address....................................... 10.156.11.239
IP NetMask....................................... 255.255.254.0
Gateway IP Addr.................................. 10.156.10.1
Cisco AP Location................................ default location
Cisco AP Group Name.............................. default-group
Primary Cisco Switch.............................
Secondary Cisco Switch...........................
Tertiary Cisco Switch............................
Administrative State ............................ ADMIN_ENABLED
Operation State ................................. REGISTERED
Mirroring Mode .................................. Disabled
AP Mode ......................................... Local
Remote AP Debug ................................. Disabled
S/W Version .................................... 3.2.171.6
Boot Version ................................... 12.3.7.1
Mini IOS Version ................................ 3.0.51.0
Stats Reporting Period .......................... 180
LED State........................................ Enabled
PoE Pre-Standard Switch.......................... Disabled
PoE Power Injector MAC Addr...................... Disabled
Number Of Slots.................................. 2
AP Model......................................... AIR-LAP1242AG-A-K9
IOS Version...................................... 12.3(7)JX6
Reset Button..................................... Enabled
AP Serial Number................................. FTX1135B2X1
AP Certificate Type.............................. Manufacture Installed
Attributes for Slot 1
Radio Type................................... RADIO_TYPE_80211a
Administrative State ........................ ADMIN_ENABLED
Operation State ............................. UP
WLAN Override ............................... Disabled
CellId ...................................... 0
Station Configuration
Configuration ............................. AUTOMATIC
Number Of WLANs ........................... 2
Medium Occupancy Limit .................... 100
CFP Period ................................ 4
CFP MaxDuration ........................... 60
BSSID ..................................... 00:1d:46:7e:d4:30
Operation Rate Set
6000 Kilo Bits........................... MANDATORY
9000 Kilo Bits........................... MANDATORY
12000 Kilo Bits.......................... MANDATORY
18000 Kilo Bits.......................... SUPPORTED
24000 Kilo Bits.......................... SUPPORTED
36000 Kilo Bits.......................... SUPPORTED
48000 Kilo Bits.......................... SUPPORTED
54000 Kilo Bits.......................... SUPPORTED
Beacon Period ............................. 100
DTIM Period ............................... 1
Fragmentation Threshold ................... 2346
Multi Domain Capability Implemented ....... TRUE
Multi Domain Capability Enabled ........... TRUE
Country String ............................ US
Multi Domain Capability
Configuration ............................. AUTOMATIC
First Chan Num ............................ 36
Number Of Channels ........................ 4
MAC Operation Parameters
Configuration ............................. AUTOMATIC
RTS Threshold ............................. 2347
Short Retry Limit ......................... 7
Long Retry Limit .......................... 4
Fragmentation Threshold ................... 2346
Maximum Tx MSDU Life Time ................. 512
Maximum Rx Life Time ...................... 512
Tx Power
Num Of Supported Power Levels ............. 8
Tx Power Level 1 .......................... 17 dBm
Tx Power Level 2 .......................... 15 dBm
Tx Power Level 3 .......................... 14 dBm
Tx Power Level 4 .......................... 11 dBm
Tx Power Level 5 .......................... 8 dBm
Tx Power Level 6 .......................... 5 dBm
Tx Power Level 7 .......................... 2 dBm
Tx Power Level 8 .......................... -1 dBm
Tx Power Configuration .................... AUTOMATIC
Current Tx Power Level .................... 1
Phy OFDM parameters
Configuration ............................. AUTOMATIC
Current Channel ........................... 149
TI Threshold .............................. -50
Antenna Type............................... EXTERNAL_ANTENNA
External Antenna Gain (in .5 dBm units).... 0
Diversity.................................. DIVERSITY_ENABLED
Performance Profile Parameters
Configuration ............................. AUTOMATIC
Interference threshold..................... 10 %
Noise threshold............................ -70 dBm
RF utilization threshold................... 80 %
Data-rate threshold........................ 1000000 bps
Client threshold........................... 12 clients
Coverage SNR threshold..................... 16 dB
Coverage exception level................... 25 %
Client minimum exception level............. 3 clients
Rogue Containment Information
Containment Count............................ 0
Cisco AP Identifier.............................. 5
Cisco AP Name.................................... AP10-MHQ-CCITS
AP Regulatory Domain............................. -A
Switch Port Number .............................. 1
MAC Address...................................... 00:19:30:76:74:82
IP Address Configuration......................... Static IP assigned
IP Address....................................... 10.156.11.233
IP NetMask....................................... 255.255.254.0
Gateway IP Addr.................................. 10.156.10.1
Cisco AP Location................................ default location
Cisco AP Group Name.............................. default-group
Primary Cisco Switch.............................
Secondary Cisco Switch...........................
Tertiary Cisco Switch............................
Administrative State ............................ ADMIN_ENABLED
Operation State ................................. REGISTERED
Mirroring Mode .................................. Disabled
AP Mode ......................................... Local
Remote AP Debug ................................. Disabled
S/W Version .................................... 3.2.171.6
Boot Version ................................... 12.3.7.1
Mini IOS Version ................................ 3.0.51.0
Stats Reporting Period .......................... 180
LED State........................................ Enabled
PoE Pre-Standard Switch.......................... Disabled
PoE Power Injector MAC Addr...................... Disabled
Number Of Slots.................................. 2
AP Model......................................... AIR-LAP1242AG-A-K9
IOS Version...................................... 12.3(7)JX6
Reset Button..................................... Enabled
AP Serial Number................................. FTX1107B3TJ
AP Certificate Type.............................. Manufacture Installed
Attributes for Slot 0
Radio Type................................... RADIO_TYPE_80211g
Administrative State ........................ ADMIN_ENABLED
Operation State ............................. UP
WLAN Override ............................... Disabled
CellId ...................................... 0
Station Configuration
Configuration ............................. AUTOMATIC
Number Of WLANs ........................... 2
Medium Occupancy Limit .................... 100
CFP Period ................................ 4
CFP MaxDuration ........................... 60
BSSID ..................................... 00:1a:30:e7:fa:60
Operation Rate Set
1000 Kilo Bits........................... MANDATORY
2000 Kilo Bits........................... MANDATORY
5500 Kilo Bits........................... MANDATORY
11000 Kilo Bits.......................... MANDATORY
6000 Kilo Bits........................... SUPPORTED
9000 Kilo Bits........................... SUPPORTED
12000 Kilo Bits.......................... SUPPORTED
18000 Kilo Bits.......................... SUPPORTED
24000 Kilo Bits.......................... SUPPORTED
36000 Kilo Bits.......................... SUPPORTED
48000 Kilo Bits.......................... SUPPORTED
54000 Kilo Bits.......................... SUPPORTED
Beacon Period ............................. 100
DTIM Period ............................... 1
Fragmentation Threshold ................... 2346
Multi Domain Capability Implemented ....... TRUE
Multi Domain Capability Enabled ........... TRUE
Country String ............................ US
Multi Domain Capability
Configuration ............................. AUTOMATIC
First Chan Num ............................ 1
Number Of Channels ........................ 11
MAC Operation Parameters
Configuration ............................. AUTOMATIC
RTS Threshold ............................. 2347
Short Retry Limit ......................... 7
Long Retry Limit .......................... 4
Fragmentation Threshold ................... 2346
Maximum Tx MSDU Life Time ................. 512
Maximum Rx Life Time ...................... 512
Tx Power
Num Of Supported Power Levels ............. 8
Tx Power Level 1 .......................... 20 dBm
Tx Power Level 2 .......................... 17 dBm
Tx Power Level 3 .......................... 14 dBm
Tx Power Level 4 .......................... 11 dBm
Tx Power Level 5 .......................... 8 dBm
Tx Power Level 6 .......................... 5 dBm
Tx Power Level 7 .......................... 2 dBm
Tx Power Level 8 .......................... -1 dBm
Tx Power Configuration .................... AUTOMATIC
Current Tx Power Level .................... 1
Phy OFDM parameters
Configuration ............................. AUTOMATIC
Current Channel ........................... 1
TI Threshold .............................. -50
Antenna Type............................... EXTERNAL_ANTENNA
External Antenna Gain (in .5 dBm units).... 0
Diversity.................................. DIVERSITY_ENABLED
Performance Profile Parameters
Configuration ............................. AUTOMATIC
Interference threshold..................... 10 %
Noise threshold............................ -70 dBm
RF utilization threshold................... 80 %
Data-rate threshold........................ 1000000 bps
Client threshold........................... 12 clients
Coverage SNR threshold..................... 12 dB
Coverage exception level................... 25 %
Client minimum exception level............. 3 clients
Rogue Containment Information
Containment Count............................ 0
Cisco AP Identifier.............................. 5
Cisco AP Name.................................... AP10-MHQ-CCITS
AP Regulatory Domain............................. -A
Switch Port Number .............................. 1
MAC Address...................................... 00:19:30:76:74:82
IP Address Configuration......................... Static IP assigned
IP Address....................................... 10.156.11.233
IP NetMask......... -
Accessing cisco wireless controller
Hi All
I have a cisco 5500 WLC that was decommissioned and is now going to be put back on the network.
I have the old IP of 10.1.2.210/24 which it was part of. I put my laptop on the same network 10.1.2.10
I access the gui whilst connected to the SP on both http & https I cannot access the browser and I cannot ping the box.
When I plug it in to one of the ports that requires an SFP. I can then ping it but still cant access it via the gui.
Can anyone help ?
ThanksHow did you configure those ports? LAG any VLAN tagging or untagged?
You can try to connect a computer and the WLC to a switch first and then try accessing it. -
Config air-lap1041n-e-k9 with cisco 5500 (5508) series wireless controller. how to?
Hi!
I try to configure a Cisco 5508 Wireless controller and 25 Air-lap1041 to use as VoIP and data. I read documents, manuals, etc, but the AP doesn't charge the configuration, or not conect with the Wireless Controller, why? No Radius server present, only WPA security.howto, please...
I try to put a static ip in the LAP, with lwapp or capwap command, (LWAPP/CAPWAP ap ip address direccion mascara) and the AP returns "You should configure Domain and Name Server from controller CLI/GUI." and i can't change the name of the AP (Command is disabled).
Log from AP:
using ÿÿÿÿ ddr static values from serial eeprom
ddr init done
Running Normal Memtest...
Passed.
IOS Bootloader - Starting system.
FLASH CHIP: Numonyx P33
Checking for Over Erased blocks
Xmodem file system is available.
DDR values used from system serial eeprom.
WRDTR,CLKTR: 0x83000800, 0xc0000000
RQDC, RFDC : 0x80000037, 0x00000184
PCIE0: link is up.
PCIE0: VC0 is active
PCIE1: link is NOT up.
PCIE1 port 1 not initialize
PCIEx: initialization done
flashfs[0]: 6 files, 2 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 32385024
flashfs[0]: Bytes used: 2369024
flashfs[0]: Bytes available: 30016000
flashfs[0]: flashfs fsck took 21 seconds.
Reading cookie from system serial eeprom...Done
Base Ethernet MAC address: 44:2b:03:dc:09:25
Ethernet speed is 1000 Mb - FULL duplex
Loading "flash:/c1140-rcvk9w8-mx/c1140-rcvk9w8-mx"...###########################
File "flash:/c1140-rcvk9w8-mx/c1140-rcvk9w8-mx" uncompressed and installed, entr
y point: 0x4000
executing...
enet halted
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
Cisco IOS Software, C1040 Software (C1140-RCVK9W8-M), Version 12.4(23c)JA, RELEA
SE SOFTWARE (fc3)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2010 by Cisco Systems, Inc.
Compiled Tue 01-Jun-10 12:53 by prod_rel_team
Proceeding with system init
Proceeding to unmask interrupts
Initializing flashfs...
FLASH CHIP: Numonyx P33
Checking for Over Erased blocks
flashfs[1]: 6 files, 2 directories
flashfs[1]: 0 orphaned files, 0 orphaned directories
flashfs[1]: Total bytes: 32126976
flashfs[1]: Bytes used: 2369024
flashfs[1]: Bytes available: 29757952
flashfs[1]: flashfs fsck took 7 seconds.
flashfs[1]: Initialization complete.
flashfs[2]: 0 files, 1 directories
flashfs[2]: 0 orphaned files, 0 orphaned directories
flashfs[2]: Total bytes: 11999232
flashfs[2]: Bytes used: 1024
flashfs[2]: Bytes available: 11998208
flashfs[2]: flashfs fsck took 1 seconds.
flashfs[2]: Initialization complete....done Initializing flashfs.
Ethernet speed is 1000 Mb - FULL duplex
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
cisco AIR-LAP1041N-E-K9 (PowerPC405ex) processor (revision B0) with 98294K/32
768K bytes of memory.
Processor board ID FCZ1611W414
PowerPC405ex CPU at 333Mhz, revision number 0x147E
Last reset from reload
LWAPP image version 7.0.94.21
1 Gigabit Ethernet interface
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: 44:2B:03:DC:09:25
Part Number : 73-14034-04
PCA Assembly Number : 800-34273-05
PCA Revision Number : A0
PCB Serial Number : FOC16075VZ3
Top Assembly Part Number : 800-34284-03
Top Assembly Serial Number : FCZ1611W414
Top Revision Number : A0
Product/Model Number : AIR-LAP1041N-E-K9
% Please define a domain-name first.
Press RETURN to get started!
Translating "CISCO-CAPWAP-CONTROLLER"...domain server (255.255.255.255)
*Mar 1 00:00:09.574: *** CRASH_LOG = YES
Base Ethernet MAC address: 44:2B:03:DC:09:25
*Mar 1 00:00:09.838: %LWAPP-3-CLIENTEVENTLOG: Read and initialized AP event log
(contains, 1024 messages)
*Mar 1 00:00:11.848: %LINK-3-UPDOWN: Interface GigabitEthernet0, changed state
to up
*Mar 1 00:00:11.892: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C1040 Software (C1140-RCVK9W8-M), Version 12.4(23c)JA, RELEA
SE SOFTWARE (fc3)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2010 by Cisco Systems, Inc.
Compiled Tue 01-Jun-10 12:53 by prod_rel_team
*Mar 1 00:08:16.954: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEth
ernet0, changed state to up
logging facility kern
^
% Invalid input detected at '^' marker.
*Mar 1 00:08:28.047: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROL
LER
*Mar 1 00:08:28.049: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*Mar 1 00:09:08.282: %CDP_PD-2-POWER_LOW: All radios disabled - LOW_POWER_CLASS
IC_NO_INJECTOR_CONFIGURED AIR-CT5508-K9 (c464.138f.9345)
*Mar 1 00:09:08.282: -Verify the required power-injector is installed on this
port: AIR-CT5508-K9(Gig 0/0/2).
*Mar 1 00:09:08.282: -If a power-injector is installed, issue the command:"pow
er inline negotiation injector installed"
*Mar 1 00:12:19.976: %CAPWAP-5-STATIC_TO_DHCP_IP: Could not discover WLC using
static IP. Forcing AP to use DHCP.
*Mar 1 00:12:29.993: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does
not have an Ip !!
*Mar 1 00:12:39.994: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does
not have an Ip !!
*Mar 1 00:12:49.993: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does
not have an Ip !!
*Mar 1 00:12:59.994: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does
not have an Ip !!
*Mar 1 00:13:09.993: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does
not have an Ip !!
Not in Bound state.
*Mar 1 00:13:19.993: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does
not have an Ip !!
*Mar 1 00:13:19.993: %CAPWAP-5-DHCP_RENEW: Could not discover WLC using DHCP IP
. Renewing DHCP IP.
logs from wireless controller:
(Cisco Controller) >show interface summary
Interface Name Port Vlan Id IP Address Type Ap Mgr Gu
est
ap-manager 2 untagged 209.165.200.231 Dynamic Yes No
management 1 untagged 209.165.200.230 Static Yes No
service-port N/A N/A 192.168.1.157 Static No No
virtual N/A N/A 1.1.1.1 Static No No
(Cisco Controller) >
i conect with service-port ok and the management port works, i think.
AP442b.03dc.0925>ping 209.165.200.230
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 209.165.200.230, timeout is 2 seconds:
Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/1 ms
AP442b.03dc.0925>
Help, please!
i write in spanish:
Hola:
Tengo que configurar un cisco 5508 wireless controller con 25 air-lap1041n, para usarlo como acceso de datos y voz. ¿Cómo lo hago? He leído manuales, y seguido las instrucciones, pero el punto de acceso parace que no es capaz de cargar el perfil. No hay servidor radius, solo la configuración de una clave wpa. Alguién me puede indicar pasos, GraciasHi!
I buy a gigabit switch. I connect the service-port to gigabit switch, and laptop to gigabit switch. I used 192.168.1.x ip address (192.168.1.157 to service-port and 192.168.1.233 to wired port on laptop, well, the laptop has two ip adress, 192.168.1.233 and 209.165.200.2, and the laptop works ok. Ping to 209.165.200.230 -ip address of management interface- and ping to 209.165.200.203 -ip address for AP, is assigned by DHCP of WLC. And i connect the ap to gigabit switch, and the wlc assigns well an ip direction.
I post the run-config and sysinfo log. The gigabit switch is tp-link model tl-sg1005d, no configuration.
Before the logs, I see this message from AP:
*Apr 19 23:10:20.211: %CAPWAP-3-ERRORLOG: This AP is not supported in controller
version 6.0.199.4 ---->What's mean that? Is it compatible the ap with the WLC? ¿Es compatible el AP con el WLC?
Hola:
He comprado un switch gigabit. Conecto el service-port al switch gigabit y el portátil también (por cable). Uso como direcciones ip el rango 192.168.1.x (192.168.1.157 asignado al service-port y 192, 168.1.233 al portátil, bueno, el portátil tiene dos direcciones, la dicha anteriormente y la 209.165.200.2) El portátil funciona bien, hace ping al 209.165.200.230 - la ip de la management interface, y a 209.165.200.203 - ip asignada al AP por el DHCP del WLC. He conectado el AP al swtich gigabit, y el dhcp del wlc asigna correctamente una dirección ip.
Añado a continuación los resultados de los comandos "show run-config" y "show sysinfo". El switch es un TP-LINK modelo TL-S1005D, sin necesidad de configuración.
Antes de mostrar los resultados de los comandos, he visto el siguiente mensaje en el log del AP:
*Apr 19 23:10:20.211: %CAPWAP-3-ERRORLOG: This AP is not supported in controller
version 6.0.199.4 ---->What's mean that? Is it compatible the ap with the WLC? ¿Es compatible el AP con el WLC?
Un saludo
Antonio R.
(Cisco Controller) >show run-config
Press Enter to continue...
System Inventory
NAME: "Chassis" , DESCR: "Cisco Wireless Controller"
PID: AIR-CT5508-K9, VID: V02, SN: FCW1608L05X
Burned-in MAC Address............................ C4:64:13:8F:93:40
Power Supply 1................................... Present, OK
Power Supply 2................................... Absent
Maximum number of APs supported.................. 25
Press Enter to continue or to abort
System Information
Manufacturer's Name.............................. Cisco Systems Inc.
Product Name..................................... Cisco Controller
Product Version.................................. 6.0.199.4
Bootloader Version............................... 1.0.1
Field Recovery Image Version..................... 6.0.182.0
Firmware Version................................. FPGA 1.3, Env 1.6, USB console
1.27
Build Type....................................... DATA + WPS
System Name...................................... CISCO-CAPWAP-CONTROLLER
System Location..................................
System Contact...................................
System ObjectID.................................. 1.3.6.1.4.1.9.1.1069
IP Address....................................... 209.165.200.230
Last Reset....................................... Power on reset
System Up Time................................... 0 days 0 hrs 17 mins 45 secs
System Timezone Location......................... (GMT +1:00) Amsterdam, Berlin,
Rome, Vienna
Current Boot License Level....................... base
Current Boot License Type........................ Permanent
Next Boot License Level.......................... base
Next Boot License Type........................... Permanent
Configured Country............................... ES - Spain
Operating Environment............................ Commercial (0 to 40 C)
Internal Temp Alarm Limits....................... 0 to 65 C
Internal Temperature............................. +36 C
External Temperature............................. +23 C
Fan Status....................................... OK
State of 802.11b Network......................... Enabled
State of 802.11a Network......................... Disabled
Number of WLANs.................................. 1
3rd Party Access Point Support................... Disabled
Number of Active Clients......................... 0
Burned-in MAC Address............................ C4:64:13:8F:93:40
Power Supply 1................................... Present, OK
Power Supply 2................................... Absent
Maximum number of APs supported.................. 25
Press Enter to continue or to abort
Switch Configuration
802.3x Flow Control Mode......................... Disable
FIPS prerequisite features....................... Disabled
secret obfuscation............................... Enabled
Network Information
RF-Network Name............................. hosp
Web Mode.................................... Disable
Secure Web Mode............................. Enable
Secure Web Mode Cipher-Option High.......... Disable
Secure Web Mode Cipher-Option SSLv2......... Enable
Secure Shell (ssh).......................... Enable
Telnet...................................... Disable
Ethernet Multicast Forwarding............... Disable
Ethernet Broadcast Forwarding............... Disable
AP Multicast/Broadcast Mode................. Unicast
IGMP snooping............................... Disabled
IGMP timeout................................ 60 seconds
User Idle Timeout........................... 300 seconds
ARP Idle Timeout............................ 300 seconds
Cisco AP Default Master..................... Enabled
AP Join Priority............................ Disable
Mgmt Via Wireless Interface................. Disable
Mgmt Via Dynamic Interface.................. Disable
Bridge MAC filter Config.................... Enable
Bridge Security Mode........................ EAP
Mesh Full Sector DFS........................ Enable
--More or (q)uit current module or to abort
--More or (q)uit current module or to abort
AP Fallback ................................ Enable
Web Auth Redirect Ports .................... 80
Fast SSID Change ........................... Disabled
IP/MAC Addr Binding Check .................. Enabled
Press Enter to continue or to abort
Port Summary
STP Admin Physical Physical Link Link
Pr Type Stat Mode Mode Status Status Trap POE SFPType
1 Normal Forw Enable Auto 1000 Full Up Enable N/A 1000BaseTX
2 Normal Disa Enable Auto Auto Down Enable N/A Not Present
3 Normal Disa Enable Auto Auto Down Enable N/A Not Present
4 Normal Disa Enable Auto Auto Down Enable N/A Not Present
5 Normal Disa Enable Auto Auto Down Enable N/A Not Present
6 Normal Disa Enable Auto Auto Down Enable N/A Not Present
7 Normal Disa Enable Auto Auto Down Enable N/A Not Present
8 Normal Disa Enable Auto Auto Down Enable N/A Not Present
Press Enter to continue or to abort
AP Summary
Number of APs.................................... 0
Global AP User Name.............................. Not Configured
Global AP Dot1x User Name........................ Not Configured
AP Name Slots AP Model Ethernet MAC Location
Port Country Priority
Press Enter to continue or to abort
Press Enter to continue or to abort
AP Location
Site Name........................................ default-group
Site Description.................................
WLAN ID Interface Network Admission Control
1 management Disabled
AP Name Slots AP Model Ethernet MAC Location
Port Country Priority GroupName
Press Enter to continue or to abort
AP Config
Press Enter to continue or to abort
Press Enter to continue or to abort
AP Airewave Director Configuration
Press Enter to continue or to abort
802.11a Configuration
802.11a Network.................................. Disabled
11nSupport....................................... Enabled
802.11a Low Band........................... Enabled
802.11a Mid Band........................... Enabled
802.11a High Band.......................... Enabled
802.11a Operational Rates
802.11a 6M Rate.............................. Mandatory
802.11a 9M Rate.............................. Supported
802.11a 12M Rate............................. Mandatory
802.11a 18M Rate............................. Supported
802.11a 24M Rate............................. Mandatory
802.11a 36M Rate............................. Supported
802.11a 48M Rate............................. Supported
802.11a 54M Rate............................. Supported
802.11n MCS Settings:
MCS 0........................................ Supported
MCS 1........................................ Supported
MCS 2........................................ Supported
MCS 3........................................ Supported
MCS 4........................................ Supported
MCS 5........................................ Supported
MCS 6........................................ Supported
--More or (q)uit current module or to abort
--More or (q)uit current module or to abort
MCS 7........................................ Supported
MCS 8........................................ Supported
MCS 9........................................ Supported
MCS 10....................................... Supported
MCS 11....................................... Supported
MCS 12....................................... Supported
MCS 13....................................... Supported
MCS 14....................................... Supported
MCS 15....................................... Supported
802.11n Status:
A-MPDU Tx:
Priority 0............................... Enabled
Priority 1............................... Disabled
Priority 2............................... Disabled
Priority 3............................... Disabled
Priority 4............................... Disabled
Priority 5............................... Disabled
Priority 6............................... Disabled
Priority 7............................... Disabled
Beacon Interval.................................. 100
CF Pollable mandatory............................ Disabled
CF Poll Request mandatory........................ Disabled
CFP Period....................................... 4
--More or (q)uit current module or to abort
--More or (q)uit current module or to abort
CFP Maximum Duration............................. 60
Default Channel.................................. 36
Default Tx Power Level........................... 0
DTPC Status..................................... Enabled
Fragmentation Threshold.......................... 2346
TI Threshold..................................... -50
Legacy Tx Beamforming setting.................... Disabled
Traffic Stream Metrics Status.................... Disabled
Expedited BW Request Status...................... Disabled
World Mode....................................... Enabled
EDCA profile type................................ default-wmm
Voice MAC optimization status.................... Disabled
Call Admision Control (CAC) configuration
Voice AC:
Voice AC - Admission control (ACM)............ Disabled
Voice max RF bandwidth........................ 75
Voice reserved roaming bandwidth.............. 6
Voice load-based CAC mode..................... Disabled
Voice tspec inactivity timeout................ Disabled
Voice Stream-Size............................. 84000
Voice Max-Streams............................. 2
Video AC:
Video AC - Admission control (ACM)............ Disabled
--More or (q)uit current module or to abort
--More or (q)uit current module or to abort
Video max RF bandwidth........................ Infinite
Video reserved roaming bandwidth.............. 0
Press Enter to continue or to abort
802.11a Advanced Configuration
Press Enter to continue or to abort
802.11a Airewave Director Configuration
RF Event and Performance Logging
Channel Update Logging......................... Off
Coverage Profile Logging....................... Off
Foreign Profile Logging........................ Off
Load Profile Logging........................... Off
Noise Profile Logging.......................... Off
Performance Profile Logging.................... Off
TxPower Update Logging......................... Off
Default 802.11a AP performance profiles
802.11a Global Interference threshold.......... 10 %
802.11a Global noise threshold................. -70 dBm
802.11a Global RF utilization threshold........ 80 %
802.11a Global throughput threshold............ 1000000 bps
802.11a Global clients threshold............... 12 clients
Default 802.11a AP monitoring
802.11a Monitor Mode........................... enable
802.11a Monitor Mode for Mesh AP Backhaul...... disable
802.11a Monitor Channels....................... Country channels
802.11a AP Coverage Interval................... 180 seconds
802.11a AP Load Interval....................... 60 seconds
802.11a AP Noise Interval...................... 180 seconds
--More or (q)uit current module or to abort
--More or (q)uit current module or to abort
802.11a AP Signal Strength Interval............ 60 seconds
Automatic Transmit Power Assignment
Transmit Power Assignment Mode................. AUTO
Transmit Power Update Interval................. 600 seconds
Transmit Power Threshold....................... -70 dBm
Transmit Power Neighbor Count.................. 3 APs
Min Transmit Power............................. -10 dBm
Max Transmit Power............................. 30 dBm
Transmit Power Update Contribution............. SNI.
Transmit Power Assignment Leader............... c4:64:13:8f:93:40
Last Run....................................... 75 seconds ago
Coverage Hole Detection
802.11a Coverage Hole Detection Mode........... Enabled
802.11a Coverage Voice Packet Count............ 100 packets
802.11a Coverage Voice Packet Percentage....... 50%
802.11a Coverage Voice RSSI Threshold.......... -80 dBm
802.11a Coverage Data Packet Count............. 50 packets
802.11a Coverage Data Packet Percentage........ 50%
802.11a Coverage Data RSSI Threshold........... -80 dBm
802.11a Global coverage exception level........ 25 %
802.11a Global client minimum exception lev.... 3 clients
Automatic Channel Assignment
Channel Assignment Mode........................ AUTO
--More or (q)uit current module or to abort
Channel Update Interval........................ 600 seconds [startup]
Anchor time (Hour of the day).................. 0
Channel Update Contribution.................... SNI.
Channel Assignment Leader...................... c4:64:13:8f:93:40
Last Run....................................... 75 seconds ago
DCA Sensitivity Level.......................... STARTUP (5 dB)
DCA 802.11n Channel Width...................... 20 MHz
DCA Minimum Energy Limit....................... -95 dBm
Channel Energy Levels
Minimum...................................... unknown
Average...................................... unknown
Maximum...................................... unknown
Channel Dwell Times
Minimum...................................... unknown
Average...................................... unknown
Maximum...................................... unknown
802.11a 5 GHz Auto-RF Channel List
Allowed Channel List......................... 36,40,44,48,52,56,60,64
Unused Channel List.......................... 100,104,108,112,116,120,124,
128,132,136,140
DCA Outdoor AP option.......................... Disabled
Radio RF Grouping
802.11a Group Mode............................. AUTO
--More or (q)uit current module or to abort
802.11a Group Update Interval.................. 600 seconds
802.11a Group Leader........................... c4:64:13:8f:93:40
802.11a Group Member......................... c4:64:13:8f:93:40
802.11a Last Run............................... 75 seconds ago
802.11b Configuration
802.11b Network.................................. Enabled
11gSupport....................................... Enabled
11nSupport....................................... Enabled
802.11b/g Operational Rates
802.11b/g 1M Rate............................ Mandatory
802.11b/g 2M Rate............................ Mandatory
802.11b/g 5.5M Rate.......................... Mandatory
802.11b/g 11M Rate........................... Mandatory
802.11g 6M Rate.............................. Supported
802.11g 9M Rate.............................. Supported
802.11g 12M Rate............................. Supported
802.11g 18M Rate............................. Supported
802.11g 24M Rate............................. Supported
802.11g 36M Rate............................. Supported
802.11g 48M Rate............................. Supported
802.11g 54M Rate............................. Supported
802.11n MCS Settings:
MCS 0........................................ Supported
MCS 1........................................ Supported
MCS 2........................................ Supported
MCS 3........................................ Supported
MCS 4........................................ Supported
--More or (q)uit current module or to abort
MCS 5........................................ Supported
MCS 6........................................ Supported
MCS 7........................................ Supported
MCS 8........................................ Supported
MCS 9........................................ Supported
MCS 10....................................... Supported
MCS 11....................................... Supported
MCS 12....................................... Supported
MCS 13....................................... Supported
MCS 14....................................... Supported
MCS 15....................................... Supported
802.11n Status:
A-MPDU Tx:
Priority 0............................... Enabled
Priority 1............................... Disabled
Priority 2............................... Disabled
Priority 3............................... Disabled
Priority 4............................... Disabled
Priority 5............................... Disabled
Priority 6............................... Disabled
Priority 7............................... Disabled
Beacon Interval.................................. 100
CF Pollable mode................................. Disabled
--More or (q)uit current module or to abort
CF Poll Request mandatory........................ Disabled
CFP Period....................................... 4
CFP Maximum Duration............................. 60
Default Channel.................................. 1
Default Tx Power Level........................... 0
DTPC Status..................................... Enabled
Call Admission Limit ........................... 105
G711 CU Quantum ................................. 15
ED Threshold..................................... -50
Fragmentation Threshold.......................... 2346
PBCC mandatory................................... Disabled
RTS Threshold.................................... 2347
Short Preamble mandatory......................... Enabled
Short Retry Limit................................ 7
Legacy Tx Beamforming setting.................... Enabled
Traffic Stream Metrics Status.................... Disabled
Expedited BW Request Status...................... Disabled
World Mode....................................... Enabled
Faster Carrier Tracking Loop..................... Disabled
EDCA profile type................................ default-wmm
Voice MAC optimization status.................... Disabled
Call Admision Control (CAC) configuration
Voice AC - Admission control (ACM)............ Disabled
--More or (q)uit current module or to abort
Voice Stream-Size............................. 84000
Voice Max-Streams............................. 2
Voice max RF bandwidth........................ 75
Voice reserved roaming bandwidth.............. 6
Voice load-based CAC mode..................... Disabled
Voice tspec inactivity timeout................ Disabled
Video AC - Admission control (ACM)............ Disabled
Video max RF bandwidth........................ 50
Video reserved roaming bandwidth.............. 0
802.11b Advanced Configuration
Press Enter to continue or to abort
802.11b Airewave Director Configuration
RF Event and Performance Logging
Channel Update Logging......................... Off
Coverage Profile Logging....................... Off
Foreign Profile Logging........................ Off
Load Profile Logging........................... Off
Noise Profile Logging.......................... Off
Performance Profile Logging.................... Off
Transmit Power Update Logging.................. Off
Default 802.11b AP performance profiles
802.11b Global Interference threshold.......... 10 %
802.11b Global noise threshold................. -70 dBm
802.11b Global RF utilization threshold........ 80 %
802.11b Global throughput threshold............ 1000000 bps
802.11b Global clients threshold............... 12 clients
Default 802.11b AP monitoring
802.11b Monitor Mode........................... enable
802.11b Monitor Channels....................... Country channels
802.11b AP Coverage Interval................... 180 seconds
802.11b AP Load Interval....................... 60 seconds
802.11b AP Noise Interval...................... 180 seconds
802.11b AP Signal Strength Interval............ 60 seconds
Automatic Transmit Power Assignment
Transmit Power Assignment Mode................. AUTO
Transmit Power Update Interval................. 600 seconds
Transmit Power Threshold....................... -70 dBm
Transmit Power Neighbor Count.................. 3 APs
Min Transmit Power............................. -10 dBm
Max Transmit Power............................. 30 dBm
Transmit Power Update Contribution............. SNI.
Transmit Power Assignment Leader............... c4:64:13:8f:93:40
Last Run....................................... 213 seconds ago
Coverage Hole Detection
802.11b Coverage Hole Detection Mode........... Enabled
802.11b Coverage Voice Packet Count............ 100 packets
802.11b Coverage Voice Packet Percentage....... 50%
802.11b Coverage Voice RSSI Threshold.......... -80 dBm
802.11b Coverage Data Packet Count............. 50 packets
802.11b Coverage Data Packet Percentage........ 50%
802.11b Coverage Data RSSI Threshold........... -80 dBm
802.11b Global coverage exception level........ 25 %
802.11b Global client minimum exception lev.... 3 clients
Automatic Channel Assignment
Channel Assignment Mode........................ AUTO
Channel Update Interval........................ 600 seconds [startup]
Anchor time (Hour of the day).................. 0
Channel Update Contribution.................... SNI.
Channel Assignment Leader...................... c4:64:13:8f:93:40
Last Run....................................... 213 seconds ago
DCA Sensitivity Level: ...................... STARTUP (5 dB)
DCA Minimum Energy Limit....................... -95 dBm
Channel Energy Levels
Minimum...................................... unknown
Average...................................... unknown
Maximum...................................... unknown
Channel Dwell Times
Minimum...................................... unknown
Average...................................... unknown
Maximum...................................... unknown
802.11b Auto-RF Allowed Channel List........... 1,6,11
Auto-RF Unused Channel List.................... 2,3,4,5,7,8,9,10,12,13
Radio RF Grouping
802.11b Group Mode............................. AUTO
802.11b Group Update Interval.................. 600 seconds
802.11b Group Leader........................... c4:64:13:8f:93:40
802.11b Group Member......................... c4:64:13:8f:93:40
802.11b Last Run............................... 213 seconds ago
Mobility Configuration
Symmetric Mobility Tunneling (current) .......... Enabled
Symmetric Mobility Tunneling (after reboot) ..... Enabled
Mobility Protocol Port........................... 16666
Default Mobility Domain.......................... hosp
Multicast Mode .................................. Disabled
Mobility Domain ID for 802.11r................... 0x97e2
Mobility Keepalive Interval...................... 10
Mobility Keepalive Count......................... 3
Mobility Group Members Configured................ 1
Mobility Control Message DSCP Value.............. 0
Controllers configured in the Mobility Group
MAC Address IP Address Group Name Multicast
IP Status
c4:64:13:8f:93:40 209.165.200.230 hosp 0.0.0.0
Up
Advanced Configuration
Probe request filtering.......................... Enabled
Probes fwd to controller per client per radio.... 0
Probe request rate-limiting interval............. 500 msec
EAP-Identity-Request Timeout (seconds)........... 30
EAP-Identity-Request Max Retries................. 2
EAP Key-Index for Dynamic WEP.................... 0
EAP Max-Login Ignore Identity Response........... enable
EAP-Request Timeout (seconds).................... 30
EAP-Request Max Retries.......................... 2
EAPOL-Key Timeout (milliseconds)................. 1000
EAPOL-Key Max Retries............................ 2
dot11-padding.................................... Disabled
Authentication Response Timeout (seconds)........ 10
Rogue Entry Timeout (seconds).................... 1200
AP Heart Beat Timeout (seconds).................. 30
AP Discovery Timeout (seconds)................... 10
AP Local mode Fast Heartbeat (seconds)........... disable
AP Hreap mode Fast Heartbeat (seconds)........... disable
AP Primary Discovery Timeout (seconds)........... 120
AP Primed Join Timeout (seconds)................. 0
Packet Forwarding watchdog timer (seconds)....... 240 (enable)
Location Configuration
RFID Tag data Collection......................... Enabled
RFID timeout.................................... 1200 seconds
RFID mobility.................................... Oui:00:14:7e : Vendor:pango S
tate:Disabled
Interface Configuration
Interface Name................................... management
MAC Address...................................... c4:64:13:8f:93:40
IP Address....................................... 209.165.200.230
IP Netmask....................................... 255.255.255.0
IP Gateway....................................... 209.165.200.1
External NAT IP State............................ Disabled
External NAT IP Address.......................... 192.168.1.1
VLAN............................................. untagged
Quarantine-vlan.................................. 0
Active Physical Port............................. 1
Primary Physical Port............................ 1
Backup Physical Port............................. Unconfigured
Primary DHCP Server.............................. 209.165.200.230
Secondary DHCP Server............................ Unconfigured
DHCP Option 82................................... Disabled
ACL.............................................. Unconfigured
AP Manager....................................... Yes
Guest Interface.................................. No
Interface Name................................... service-port
MAC Address...................................... c4:64:13:8f:93:41
IP Address....................................... 192.168.1.157
IP Netmask....................................... 255.255.255.0
DHCP Option 82................................... Disabled
DHCP Protocol.................................... Disabled
AP Manager....................................... No
Guest Interface.................................. No
Interface Name................................... virtual
MAC Address...................................... c4:64:13:8f:93:40
IP Address....................................... 1.1.1.1
DHCP Option 82................................... Disabled
Virtual DNS Host Name............................ Disabled
AP Manager....................................... No
Guest Interface.................................. No
WLAN Configuration
WLAN Identifier.................................. 1
Profile Name..................................... HOSP3C
Network Name (SSID).............................. HOSP3C
Status........................................... Enabled
MAC Filtering.................................... Disabled
Broadcast SSID................................... Enabled
AAA Policy Override.............................. Disabled
Network Admission Control
NAC-State...................................... Disabled
Quarantine VLAN................................ 0
Number of Active Clients......................... 0
Exclusionlist Timeout............................ 60 seconds
Session Timeout.................................. 1800 seconds
CHD per WLAN..................................... Enabled
Webauth DHCP exclusion........................... Disabled
Interface........................................ management
WLAN ACL......................................... unconfigured
DHCP Server...................................... 209.165.200.230
DHCP Address Assignment Required................. Enabled
Quality of Service............................... Platinum (voice)
Scan Defer Priority.............................. 5,6
Scan Defer Time.................................. 100 milliseconds
WMM.............................................. Disabled
Media Stream Multicast-direct.................... Disabled
CCX - AironetIe Support.......................... Enabled
CCX - Gratuitous ProbeResponse (GPR)............. Disabled
CCX - Diagnostics Channel Capability............. Disabled
Dot11-Phone Mode (7920).......................... Disabled
Wired Protocol................................... None
IPv6 Support..................................... Disabled
Peer-to-Peer Blocking Action..................... Disabled
Radio Policy..................................... 802.11b and 802.11g only
DTIM period for 802.11a radio.................... 1
DTIM period for 802.11b radio.................... 1
Radius Servers
Authentication................................ Disabled
Accounting.................................... Disabled
Dynamic Interface............................. Disabled
Local EAP Authentication......................... Disabled
Security
802.11 Authentication:........................ Open System
Static WEP Keys............................... Disabled
802.1X........................................ Disabled
Wi-Fi Protected Access (WPA/WPA2)............. Enabled
WPA (SSN IE)............................... Disabled
WPA2 (RSN IE).............................. Enabled
TKIP Cipher............................. Enabled
AES Cipher.............................. Enabled
Auth Key Management
802.1x.................................. Disabled
PSK..................................... Enabled
CCKM.................................... Disabled
FT(802.11r)............................. Disabled
FT-PSK(802.11r)......................... Disabled
FT Reassociation Timeout......................... 20
FT Over-The-Air mode............................. Enabled
FT Over-The-Ds mode.............................. Enabled
CKIP ......................................... Disabled
Web Based Authentication...................... Disabled
Web-Passthrough............................... Disabled
Conditional Web Redirect...................... Disabled
Splash-Page Web Redirect...................... Disabled
Auto Anchor................................... Disabled
H-REAP Local Switching........................ Disabled
H-REAP Learn IP Address....................... Enabled
Infrastructure MFP protection................. Enabled
Client MFP.................................... Optional
Tkip MIC Countermeasure Hold-down Timer....... 60
Call Snooping.................................... Disabled
Band Select...................................... Enabled
Load Balancing................................... Enabled
Mobility Anchor List
WLAN ID IP Address Status
Press Enter to continue or to abort
Press Enter to continue or to abort
ACL Configuration
Press Enter to continue or to abort
CPU ACL Configuration
CPU Acl Name................................ NOT CONFIGURED
Wireless Traffic............................ Disabled
Wired Traffic............................... Disabled
RADIUS Configuration
Vendor Id Backward Compatibility................. Disabled
Call Station Id Case............................. lower
Call Station Id Type............................. IP Address
Aggressive Failover.............................. Enabled
Keywrap.......................................... Disabled
Fallback Test:
Test Mode.................................... Off
Probe User Name.............................. cisco-probe
Interval (in seconds)........................ 300
MAC Delimiter for Authentication Messages........ hyphen
MAC Delimiter for Accounting Messages............ hyphen
Authentication Servers
Idx Type Server Address Port State Tout RFC3576 IPSec - AuthMode/P
hase1/Group/Lifetime/Auth/Encr
Accounting Servers
Idx Type Server Address Port State Tout RFC3576 IPSec - AuthMode/P
hase1/Group/Lifetime/Auth/Encr
--More or (q)uit current module or to abort
TACACS Configuration
Authentication Servers
Idx Server Address Port State Tout
Authorization Servers
Idx Server Address Port State Tout
Accounting Servers
Idx Server Address Port State Tout
LDAP Configuration
Press Enter to continue or to abort
Local EAP Configuration
User credentials database search order:
Primary ..................................... Local DB
Timer:
Active timeout .............................. 300
Configured EAP profiles:
EAP Method configuration:
EAP-FAST:
Server key ................................
TTL for the PAC ........................... 10
Anonymous provision allowed ............... Yes
Authority ID .............................. 436973636f00000000000000000000
00
Authority Information ..................... Cisco A-ID
Press Enter to continue or to abort
HREAP Group Summary
HREAP Group Summary: Count: 0
Group Name # Aps
Press Enter to continue or to abort
HREAP Group Detail
Press Enter to continue or to abort
Route Info
Number of Routes................................. 0
Destination Network Netmask Gateway
Press Enter to continue or to abort
Qos Queue Length Info
Platinum queue length............................ 100
Gold queue length................................ 75
Silver queue length.............................. 50
Bronze queue length.............................. 25
Press Enter to continue or to abort
Mac Filter Info
Press Enter to continue or to abort
Authorization List
Authorize MIC APs against AAA ................... disabled
Authorize LSC APs against Auth-List ............. disabled
Allow APs with MIC - Manufactured Installed C.... disabled
Allow APs with SSC - Self-Signed Certificate..... disabled
Allow APs with LSC - Locally Significant Cert.... disabled
Load Balancing Info
Aggressive Load Balancing........................ Disabled
Aggressive Load Balancing Window................. 5 clients
Aggressive Load Balancing Denial Count........... 3
Statistics
Total Denied Count............................... 0 clients
Total Denial Sent................................ 0 messages
Exceeded Denial Max Limit Count.................. 0 times
None 5G Candidate Count.......................... 0 times
None 2.4G Candidate Count........................ 0 times
Press Enter to continue or to abort
Dhcp Scope Info
Scope: PUNTOSAP
Enabled.......................................... Yes
Lease Time....................................... 86400 (1 day )
Pool Start....................................... 209.165.200.201
Pool End......................................... 209.165.200.229
Network.......................................... 209.165.200.0
Netmask.......................................... 255.255.255.0
Default Routers.................................. 0.0.0.0 0.0.0.0 0.0.0.0
DNS Domain.......................................
DNS.............................................. 0.0.0.0 0.0.0.0 0.0.0.0
Netbios Name Servers............................. 0.0.0.0 0.0.0.0 0.0.0.0
Press Enter to continue or to abort
Exclusion List ConfigurationUnable to retrieve exclusion-list entry
Press Enter to continue or to abort
CDP Configuration
Press Enter to continue or to abort
Country Channels Configuration
Configured Country............................. ES - Spain
KEY: * = Channel is legal in this country and may be configured manually.
A = Channel is the Auto-RF default in this country.
. = Channel is not legal in this country.
C = Channel has been configured for use by Auto-RF.
x = Channel is available to be configured for use by Auto-RF.
(-,-) = (indoor, outdoor) regulatory doamin allowed by this country.
-----------------:+-+-+-+-+-+-+-+-+-+-+-+-+-+-
802.11bg :
Channels : 1 1 1 1 1
: 1 2 3 4 5 6 7 8 9 0 1 2 3 4
-----------------:+-+-+-+-+-+-+-+-+-+-+-+-+-+-
ES (-E ,-E ): A * * * * A * * * * A * * .
-----------------:+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-
802.11a : 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
Channels : 3 3 3 4 4 4 4 4 5 5 6 6 0 0 0 1 1 2 2 2 3 3 4 4 5 5 6 6
: 4 6 8 0 2 4 6 8 2 6 0 4 0 4 8 2 6 0 4 8 2 6 0 9 3 7 1 5
-----------------:+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-
ES (-E ,-E ): . A . A . A . A A A A A * * * * * * * * * * * . . . . .
Press Enter to continue or to abort
WPS Configuration Summary
Auto-Immune
Auto-Immune.................................... Disabled
Client Exclusion Policy
Excessive 802.11-association failures.......... Enabled
Excessive 802.11-authentication failures....... Enabled
Excessive 802.1x-authentication................ Enabled
IP-theft....................................... Enabled
Excessive Web authentication failure........... Enabled
Signature Policy
Signature Processing........................... Enabled
Press Enter to continue or to abort
Custom Web Configuration
Radius Authentication Method..................... PAP
Cisco Logo....................................... Enabled
CustomLogo....................................... None
Custom Title..................................... None
Custom Message................................... None
Custom Redirect URL.............................. None
Web Authentication Type.......................... Internal Default
External Web Authentication URL.................. None
Configuration Per Profile:
Rogue AP Configuration
Rogue Location Discovery Protocol................ Disabled
Rogue on wire Auto-Contain....................... Disabled
Rogue using our SSID Auto-Contain................ Disabled
Valid client on rogue AP Auto-Contain............ Disabled
Rogue AP timeout................................. 1200
MAC Address Classification # APs # Clients Last Heard
Adhoc Rogue Configuration
Detect and report Ad-Hoc Networks................ Enabled
Auto-Contain Ad-Hoc Networks..................... Disabled
Client MAC Address Adhoc BSSID State # APs Last Heard
Rogue Client Configuration
Validate rogue clients against AAA............... Disabled
Rogue Client Configuration
Validate rogue clients against AAA............... Disabled
--More-- or (q)uit
MAC Address State # APs Last Heard
Ignore List Configuration
MAC Address
Rogue Rule Configuration
Priority Rule Name State Type Match Hit Count
(Cisco Controller) >show sysinfo
Manufacturer's Name.............................. Cisco Systems Inc.
Product Name..................................... Cisco Controller
Product Version.................................. 6.0.199.4
Bootloader Version............................... 1.0.1
Field Recovery Image Version..................... 6.0.182.0
Firmware Version................................. FPGA 1.3, Env 1.6, USB console
1.27
Build Type....................................... DATA + WPS
System Name...................................... CISCO-CAPWAP-CONTROLLER
System Location..................................
System Contact...................................
System ObjectID.................................. 1.3.6.1.4.1.9.1.1069
IP Address....................................... 209.165.200.230
Last Reset....................................... Power on reset
System Up Time................................... 0 days 0 hrs 41 mins 2 secs
System Timezone Location......................... (GMT +1:00) Amsterdam, Berlin,
Rome, Vienna
Current Boot License Level....................... base
Current Boot License Type........................ Permanent
Next Boot License Level.......................... base
Next Boot License Type........................... Permanent
Configured Country............................... ES - Spain
Operating Environment............................ Commercial (0 to 40 C)
Internal Temp Alarm Limits....................... 0 to 65 C
Internal Temperature............................. +39 C
External Temperature............................. +23 C
Fan Status....................................... OK
State of 802.11b Network......................... Enabled
State of 802.11a Network......................... Disabled
Number of WLANs.................................. 1
3rd Party Access Point Support................... Disabled
Number of Active Clients......................... 0
Burned-in MAC Address............................ C4:64:13:8F:93:40
Power Supply 1................................... Present, OK
Power Supply 2................................... Absent
Maximum number of APs supported.................. 25
(Cisco Controller) >
The AP log
AP442b.03dc.0925>
*Apr 19 23:10:18.428: %CAPWAP-3-ERRORLOG: Selected MWAR 'CISCO-CAPWAP-CONTROLLER
'(index 0).
*Apr 19 23:10:18.428: %CAPWAP-3-ERRORLOG: Go join a capwap controller
logging facility kern
^
% Invalid input detected at '^' marker.
logging facility kern
^
% Invalid input detected at '^' marker.
*Apr 19 23:10:19.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_i
p: 209.165.200.230 peer_port: 5246
*Apr 19 23:10:19.001: %CAPWAP-5-CHANGED: CAPWAP changed state to
*Apr 19 23:10:20.200: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully
peer_ip: 209.165.200.230 peer_port: 5246
*Apr 19 23:10:20.201: %CAPWAP-5-SENDJOIN: sending Join Request to 209.165.200.23
0
*Apr 19 23:10:20.201: %CAPWAP-5-CHANGED: CAPWAP changed state to JOIN
*Apr 19 23:10:20.211: %CAPWAP-3-ERRORLOG: This AP is not supported in controller
version 6.0.199.4 ---->What's mean that? Is it compatible the ap with the WLC? ¿Es compatible el AP con el WLC?
*Apr 19 23:10:20.354: %CAPWAP-5-CHANGED: CAPWAP changed state to CFG
*Apr 19 23:10:20.355: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 209
.165.200.230:5246
*Apr 19 23:10:20.356: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*Apr 19 23:10:20.356: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*Apr 19 23:10:20.412: %CAPWAP-3-ERRORLOG: Dropping dtls packet since session is
not established -
Cisco 5508 Wireless Controller with Splash Page Disclaimer
How do one configure a splash disclaimer page on a Cisco Wireless Controller 5508 with no authentication?
JimmyThere are many options to you in this scenario, but if you're looking to simply provide a splash page via the WLC without interacting with any other web servers, you can configure Local Web Authentication (LWA) as seen in this configuration example.
http://www.cisco.com/c/en/us/support/docs/wireless-mobility/wlan-security/69340-web-auth-config.html?referring_site=RE&pos=1&page=http://www.cisco.com/c/en/us/support/docs/wireless-mobility/wlan-security/71881-ext-web-auth-wlc.html
If you are not wanting the authentication, you can choose the "passthrough" method which will not require any credentials, only accepting an AUP or whatever you want. -
Managing remote C800 with the wireless controller
We have a number of regional offices throughout the country with a C800 as the Internet facing router and it is also our wireless.
We have a Cisco wireless controller in the Data Center an we need to manage\monitor all the C800, but the problem is that those remote sites
are not VPN'd nor part of our WAN network.
Which setup do you
/* Style Definitions */
table.MsoNormalTable
{mso-style-name:"Table Normal";
mso-tstyle-rowband-size:0;
mso-tstyle-colband-size:0;
mso-style-noshow:yes;
mso-style-priority:99;
mso-style-qformat:yes;
mso-style-parent:"";
mso-padding-alt:0in 5.4pt 0in 5.4pt;
mso-para-margin:0in;
mso-para-margin-bottom:.0001pt;
mso-pagination:widow-orphan;
font-size:11.0pt;
font-family:"Calibri","sans-serif";
mso-ascii-font-family:Calibri;
mso-ascii-theme-font:minor-latin;
mso-hansi-font-family:Calibri;
mso-hansi-theme-font:minor-latin;}
recommend:
1) 1) WLC to monitor the C800 using its public IP address
1) 2) Create a VPN tunnel from each of the remote sites to our data center and only allow wireless to go through for mgmt purposes
anany other options?
TFirst question is which 800 do you have ? there's like 20 different versions out there.
If you talk about WLC, I would suppose you have something like the 880 ?
I'm afraid the WLC will need the internal AP ip address. So you would need to do so reverse nat to direct public ip address tarffic on capwap ports to the internal AP.
This or the VPN tunnel.
Nicolas
===
Don't forget to rate answers that you find useful -
Clients are unable to access a New wireless Controller 5508
Clients are unable to access the public ssid, which is wide open(or any other ssids).
I'm using LAG and I can ping each interface on the controller. Ap's show a total of 2 and 2 are up.
interface name is public vlan identifier 107, ip add 10.1.255.252, interface dynamic
Software version 7.0.98.0
Model No.
AIR-CT5508-K9
Burned-in MAC Address
50:3D:E5:1A:2F:60
Maximum number of APs supported
25
FIPS Prerequisite Mode
Disable
UDI :
Product Identifier Description
AIR-CT5508-K9
Version Identifier Description
V01
Serial Number
FCW1508L0KT
Entity Name
Chassis
Entity Description
Cisco Wireless Controller
Profile Name
Type
SSID
Status
Enabled
Security Policies
(Modifications done under security tab will appear after applying the changes.)
Radio Policy
All 802.11a only 802.11a/g only 802.11g only 802.11b/g only
Interface
jmhmanagementpublicspacelabsvoice
Broadcast SSID
Enabled
Layer 2 security none
Below is the errors that are in the controller's log.
spamApTask0: Dec 06 14:54:43.895: %LWAPP-3-DECODE_ERR: spam_lrad.c:1932 Error decoding join request from AP 00:00:00:00:00:00
*spamApTask0: Dec 06 14:54:43.895: %LWAPP-3-JOIN_DB_ERR: spam_lrad.c:6216 Could not allocate an entry in the database for AP 00:00:00:00:00:00 - dropping the join request (# of APs joined = 2)
*spamApTask0: Dec 06 14:54:43.895: %LWAPP-3-AP_DB_CREATE_ERR: spam_lrad.c:4945 Unable to create an entry for AP 00:00:00:00:00:00 in the database - invalid mac address
*spamApTask0: Dec 06 14:54:43.895: %LWAPP-3-PAYLOAD_MISSING: spam_lrad.c:5400 Join request does not contain BOARD_DATA payload
*spamApTask0: Dec 06 14:54:24.728: %LWAPP-3-DECODE_ERR: spam_lrad.c:1932 Error decoding join request from AP 00:00:00:00:00:00
*spamApTask0: Dec 06 14:54:24.728: %LWAPP-3-JOIN_DB_ERR: spam_lrad.c:6216 Could not allocate an entry in the database for AP spamApTask0: Dec 06 14:54:43.895: %LWAPP-3-DECODE_ERR: spam_lrad.c:1932 Error decoding join request from AP 00:00:00:00:00:00
*spamApTask0: Dec 06 14:54:43.895: %LWAPP-3-JOIN_DB_ERR: spam_lrad.c:6216 Could not allocate an entry in the database for AP 00:00:00:00:00:00 - dropping the join request (# of APs joined = 2)
*spamApTask0: Dec 06 14:54:43.895: %LWAPP-3-AP_DB_CREATE_ERR: spam_lrad.c:4945 Unable to create an entry for AP 00:00:00:00:00:00 in the database - invalid mac address
*spamApTask0: Dec 06 14:54:43.895: %LWAPP-3-PAYLOAD_MISSING: spam_lrad.c:5400 Join request does not contain BOARD_DATA payload
*spamApTask0: Dec 06 14:54:24.728: %LWAPP-3-DECODE_ERR: spam_lrad.c:1932 Error decoding join request from AP 00:00:00:00:00:00
*spamApTask0: Dec 06 14:54:24.728: %LWAPP-3-JOIN_DB_ERR: spam_lrad.c:6216 Could not allocate an entry in the database for AP
I have attached show run-config and show running-configFor the public WLAN, what is 10.1.1.1? Is it a real DHCP server, is it a FW? If it's a FW, then you'll need to disable dhcp proxy:
CLI config dhcp proxy disable
GUI Controller > Advanced > DHCp, and uncheck the box for proxy.
As for all of your other SSID, they are all pointd at the management interface. Double check the WLAN config, and point them to the interface you want the user to get an IP address in.
HTH,
Steve
Please remember to rate helpful posts or to mark the question as answered so that it can be found later. -
Wireless controller system software .aes (6500 WISM)
hi,
i am looking around how to copy system software .aes to tftp server . and ram installed in WLC of 6500 wism ?
try looking any command, i want to copy WLC software to tftp server . Because My WLC software version can not be found in the Cisco official website
thanks..
--------------Show udi---------------
NAME: "Chassis" , DESCR: "Cisco Wireless Controller"
PID: WS-SVC-WISM-1-K9, VID: V01, SN: FAS120906VL
---------------Show sysinfo---------------
System Information
Manufacturer's Name.............................. Cisco Systems Inc.
Product Name..................................... Cisco Controller
Product Version.................................. 6.0.199.157
RTOS Version..................................... 6.0.199.157
Bootloader Version............................... 4.0.219.0
Emergency Image Version.......................... N/A
Build Type....................................... DATA + WPS
System Name...................................... gangtie-2
System Location..................................
System Contact...................................
System ObjectID.................................. 1.3.6.1.4.1.14179.1.1.4.4
IP Address....................................... 10.107.74.60
System Up Time................................... 59 days 19 hrs 36 mins 12 secs
System Timezone Location.........................
--More-- or (q)uit% I
.................. 5168172 Secs
erhead bytes)
ar 13 10:09:27.916: %APF-6-MOBILE_NOT_EXCLUDED: apf_ms.c:3785 Could not exclude the mobile 00:50:f6:2d:85:8b.
Configured Country............................... CN - China
Operating Environment............................ Commercial (0 to 40 C)
Internal Temp Alarm Limits....................... 0 to 65 C
Internal Temperature............................. +42 C
State of 802.11b Network......................... Disabled
State of 802.11a Network......................... Enabled
Number of WLANs.................................. 1
3rd Party Access Point Support................... Disabled
Number of Active Clients......................... 224
Burned-in MAC Address............................ 00:1E:F7:D6:FE:E0
Maximum number of APs supported.................. 150
---------------Show Interface ---------------
Interface Configuration
Interface Name................................... ap-manager
MAC Address...................................... 00:1e:f7:d6:fe:eb
IP Address....................................... 10.107.76.8
IP Netmask....................................... 255.255.248.0
IP Gateway....................................... 10.107.76.1
--More-- or (q)uit
External NAT IP State............................ Disabled
External NAT IP Address.......................... 0.0.0.0
VLAN............................................. untagged
Active Physical Port............................. LAG (29)
Primary Physical Port............................ LAG (29)
Backup Physical Port............................. Unconfigured
Primary DHCP Server.............................. 10.107.76.1
Secondary DHCP Server............................ Unconfigured
DHCP Option 82................................... Disabled
ACL.............................................. Unconfigured
AP Manager....................................... Yes
Guest Interface.................................. No--------------Show udi---------------
NAME: "Chassis" , DESCR: "Cisco Wireless Controller"
PID: WS-SVC-WISM-1-K9, VID: V01, SN: FAS120906VL
---------------Show sysinfo---------------
System Information
Manufacturer's Name.............................. Cisco Systems Inc.
Product Name..................................... Cisco Controller
Product Version.................................. 6.0.199.157
RTOS Version..................................... 6.0.199.157
Bootloader Version............................... 4.0.219.0
Emergency Image Version.......................... N/A
Build Type....................................... DATA + WPS
System Name...................................... gangtie-2
System Location..................................
System Contact...................................
System ObjectID.................................. 1.3.6.1.4.1.14179.1.1.4.4
IP Address....................................... 10.107.74.60
System Up Time................................... 59 days 19 hrs 36 mins 12 secs
System Timezone Location.........................
--More-- or (q)uit% I
.................. 5168172 Secs
erhead bytes)
ar 13 10:09:27.916: %APF-6-MOBILE_NOT_EXCLUDED: apf_ms.c:3785 Could not exclude the mobile 00:50:f6:2d:85:8b.
Configured Country............................... CN - China
Operating Environment............................ Commercial (0 to 40 C)
Internal Temp Alarm Limits....................... 0 to 65 C
Internal Temperature............................. +42 C
State of 802.11b Network......................... Disabled
State of 802.11a Network......................... Enabled
Number of WLANs.................................. 1
3rd Party Access Point Support................... Disabled
Number of Active Clients......................... 224
Burned-in MAC Address............................ 00:1E:F7:D6:FE:E0
Maximum number of APs supported.................. 150
---------------Show Interface ---------------
Interface Configuration
Interface Name................................... ap-manager
MAC Address...................................... 00:1e:f7:d6:fe:eb
IP Address....................................... 10.107.76.8
IP Netmask....................................... 255.255.248.0
IP Gateway....................................... 10.107.76.1
--More-- or (q)uit
External NAT IP State............................ Disabled
External NAT IP Address.......................... 0.0.0.0
VLAN............................................. untagged
Active Physical Port............................. LAG (29)
Primary Physical Port............................ LAG (29)
Backup Physical Port............................. Unconfigured
Primary DHCP Server.............................. 10.107.76.1
Secondary DHCP Server............................ Unconfigured
DHCP Option 82................................... Disabled
ACL.............................................. Unconfigured
AP Manager....................................... Yes
Guest Interface.................................. No -
We have a Cisco wireless controller and having some issue getting an ip address when connecting to an AP.
SSID is broadcasting and that's fine, but a laptop will not pickup an ip address.
we have a dhcp scope defined and enabled.
any idea?is the user authenticated?
> check if you can do all desired things when using a static IP address
Are you using a DHCP scope defined on the WLC or an external DHCP server?
> Check which interface is used for the WLAN. Then check for this interface (controller>interfaces) if the IP address of the DHCP server is configured. If you're using the WLC as DHCP server, use the Management interface as ip address, else the IP address of the DHCP server.
Or do you want to prefer the IP helper address? > disable DHCP proxy
Maybe you are looking for
-
I was just about to order a photo book, using photos stored on an external hard drive. I organised the book and pressed 'buy'. IPhotos instructed me that I needed to upgrade and so I went on the ASpp store, bought the upgrade and installed as directe
-
I have a number questions that I want to know the average of all the before and after data to compare them, how do I set this up in a form in FormsCentral? Here is an example of what I want to do - the green bar is "before" and blue is "after"
-
Photoshop crashing for a month with no solution found
Hello, and thank you in advance to anyone who takes the time to read and possibly reply to this. I've had Photoshop CS3 running on my Mac OS since 2011, with no problems until February of this year. For reasons unknown to me, the software started cra
-
Hi, I have photo galleries loading via an xml file. Right now, it stops at the last photo. I would like it to "loop" back to the first photo instead of stopping and vice versa for the previous button. Here is my code for next and previous buttons. Th
-
Matching credit note to a prepayment
Hi, We are paying our electricity supplier by direct debit, so we enter a prepayment onto the purchase ledger. When the invoices are received, we match them against the prepayment. We are now facing difficulties because the amount of the payment take