System 7.1 "not enough memory to open program"

Yes, I know this is not the corect place but it was the closest I could get.
I have a Macintosh LC II running System 7.1.
The machine has been working fine and I have not done anything new/installed.
I attepmted to open "Making The Grade" when I get an error "There is not enough memory to open "Making The Grade 8.0g" (2,250K Needed, 2,113K available)"
It has never done this before, When I go look at my "About This Macintosh" I see that I have 4,096K total and the Largest unused block: 2,107K. I have removed other programs and removed files from my machine and nothing helps.
So, my question would be what other Software/settings could I use/try to help with this issue.
Should I use the "Virtual Memory" setting and let it use disk space? I have 52M available on the drive.
I havealready turned my Cache size down to 32K, hoping to free up space. But still the same issue.
Also, if I do use the Virtual memory will this have a negative affect on anything else?
Message was edited by: How_weird, Added more information.

Hi, How -
Welcome to Apple's Discussions.
The issue probably stems from the fact that in order to open (run) a program, it needs sufficient contiguous memory be available for it to use, not just sufficient memory. A program can not use non-contiguous chunks of memory.
That is why "About This Macintosh" reports the largest unused block (a 'block' is a contiguous chunk) available, rather than the raw total of unused memory.
Often after opening some smaller programs the RAM will become fragmented. Quitting some of those apps may free up a lot of total memory, but not enough in a contiguous chunk for the needs of a large program.
Restarting the machine clears all RAM, which is why Niel suggested doing that. After the machine has finished restarting, all memory not then in use will effectively be contiguous and available for that program. If you have any programs set to be opened (run) automatically at startup, you may wish to disable that for the duration of your need for the larger program.
More info about fragmentation of memory (RAM) here -
Article #TA21681 - Minimizing Memory Fragmentation
I know this is not the corect place but it was the closest I could get.
It's not highly obvious. On the Discussions mainpage, scroll down until you can see and click the link named "Older software products". On the Category page to which that link takes you, you will find a link for OS 7 and earlier OS's -
http://discussions.apple.com/forum.jspa?forumID=641

Similar Messages

6300 - not enough memory to open programs/send txt...

Hi, new member to the boards - hello!
The problem with my 6300 is as follows - whenever i get about 10 mesgs overall on the phone (say 6 mesgs in the inbox and 4 in the sent box) a mesg comes up saying that the phone can't send or receive mesgs because theres not enough memory. Also, when i try and open certain applications, such as snake or converter, the phone will say 'unable to open, please close some applications and try again' when i've got nothing else open.
The memory card seems to work fine and it is recognised by the phone no problem.
If anyone could help me out i would really appreciate it.
Cheers, Will

I deleted some game and gain 1MB of Ram. Yes its quite low...strange. I need to check some friend phone which have the same type. I think that more stuff installed on phone means less ram memory available, although only some of them are rally active in stand by or none of them...I asked another friend if he have the same problem. I dont know exactly what is the model of his phone, but i now he have a symbian 3rd phone s60...the first one of this s60 3rd generation. He have the same problem when talking about opening the swf videos. I think that the phone try to fill the whole movie into his ram and then play it....so it doesnt work. When opening the avi videos..using smart movie player for symbian...no problems at all. Also using the original real player works ok, but the real player that is integrated does not support avi formats. It support mp4 format and some other. The smart movie player support avi formats, divx, xvid, mp4... I chose smart movie player because it has more functionalities then nokia real player. try it.
More info: http://www.lonelycatgames.com/?app=smartmovieMessage Edited by m4dj on 25-Nov-200709:54 PM
Regards

Not enough memory to open the illustration error

I have Adobe CS5.
I am running it on a laptop with 4 GB of memory.
Windows 6.1
but when I open the system info in the product, it says I have 3836 MB of memory.
Only Illlustrator is loaded and I cannot open any illustrator files. I cannot even make a blank file.
I get the error message not enough memory to open the illustration.
I have uninstalled and reinstalled this product and it still doesn't work.
I tried the chat after 10 minutes of waiting for help they said they no longer support CS5 please try the phone.
I spent 20 minutes on hold only to find out that phone support is no longer available unless I want to spend $40 for an answer.
I am pretty angry and frustrated.
I have searched my computer for a /etc/launchd.conf file but I cannot find it.
I am stuck please help.

I have searched my computer for a /etc/launchd.conf file but I cannot find it.
That would be Mac only.... Anyway, start by trashing the prefs in the prefs folder:
Important Directories
Beyond that you might consider reinstalling Adobe Reader/ Acrobat. Some of these errors are caused by damaged shared PDf components. if the machine has a specific printer installed, remove it (temporarily) and uninstall its driver. This may also help, if files have stored printer information. Likewise, check your system's color settings and color profile usage. "Bad" profiles can have all sorts of negative influence...
Mylenium

Error Message "Not Enough Memory to Open Illustrator"

Hi,
Im running adobe illustrator cs5 on windows 7 and have previously had no problems. Today however when I opened a pdf I got the error message "Not enough memory to open illustrator" I have searched and cannot find a reason for this error. It now happens nearly every time I open a pdf. I increased my windows 7 virtual memory, however, this does not seem to have any effect. Any assistance would be appreciated.

Something is blocking PDF handling (a security tool) on the system level and/or one of the shared Adobe components for PDF handling has been updated/ changed, most likely. Do the PDFs properly open in Acrobat/ Adobe Reader? Investigate these things. Also of course simply trash your AI prefs to make sure you are not a victim of tainted config data...
Mylenium

I see message "Cannot open the file. Not enough memory to open the file"

When I'm trying to open file from adobe.com on my tablet, I see massage " Cannot open the file. Not enough memory to open the file" . I've got 10 gb free memory , so I dont know, why...

Which system are you running (is this information correct in your profile)?
Are there complicating issues to this question such as you transferring libraries between computers?
Have you upgraded iTunes recently?
Troubleshooting iTunes installation on Mac OS X - http://support.apple.com/kb/HT2311 - read section on Opening iTunes for information about running multiple copies of iTunes.

Error coming - NOT ENOUGH MEMORY while opening MUS...

Hi
i have bought nokia 7210 supernova , error is coming NOT ENOUGH MEMORY while opening MUSIC PLAYER
can any1 help me in ths plz

i am using nokia 5130 Xpress music mobile.i got same problem,but i take backup file of "settings" from my friends 5130 Xpress music. i restore that backup i get music player again.
So u people also try to get "settings" Backup file from ur friends restore that file,it may be works.............thnx.
MODERATOR'S NOTE: We would like to inform you that we have removed your email address on this post as it is unwise to publish personal details on public forums like this for security purpose.
S.Krishna Chaitanya Reddy

Not Enough memory to open the Illustration

Hi,
I saw in the site http://kb2.adobe.com/cps/832/cpsid_83270.html
that below problem exist. Is that been solved. Is there any alternative way to perform the action.
Error "Not Enough memory to open the Illustration" when opening a placed image InDesign CS4 with Illustrator hidden
Thanks
Karthik B

Firstly, you may apply free to try product, it would repair your problem illustrator file and to import it to new .ai file with saving all content. This tool is named Illustrator Repair Toolbox. Prove it for free from here: http://www.illustrator.repairtoolbox.com/
This solution from adobe blog
Make Illustrator visible.
This issue appears only on Mac OS 10.6.x. The error message sometimes occurs when you drag files from the Finder to the Illustrator icon in the dock. The error can also occur when you right-click an Illustrator SmartObject in Photoshop and choose Edit Contents.
As ultimate measure you have to upgrade your MAC OS.

Not enough memory to open file NOKIA 6120

Hi !
I have nokia 6120. I have also sandisk micro sd card (mobile premiere) with 1GB storage. I transfered a flash movie of 20Mb and another one of 11Mb into the card memory. I tryed to play it with flash player that is installed on the phone. When i select to play it from the file manager , it gives me a error: not enough memory to open file. On the phone i have 11 Mb of memory ow, but the movie is located on the sd card. I dont know why it gives me this error. I think its mean that i even cant play any of the other videos from the card ... for example a divx or avi movie !???
Anybody have the same problem ? I hope that there is a fix for this otherwise i have a big card that I cant use for such storage.... that will be a big shame.
Regards

I deleted some game and gain 1MB of Ram. Yes its quite low...strange. I need to check some friend phone which have the same type. I think that more stuff installed on phone means less ram memory available, although only some of them are rally active in stand by or none of them...I asked another friend if he have the same problem. I dont know exactly what is the model of his phone, but i now he have a symbian 3rd phone s60...the first one of this s60 3rd generation. He have the same problem when talking about opening the swf videos. I think that the phone try to fill the whole movie into his ram and then play it....so it doesnt work. When opening the avi videos..using smart movie player for symbian...no problems at all. Also using the original real player works ok, but the real player that is integrated does not support avi formats. It support mp4 format and some other. The smart movie player support avi formats, divx, xvid, mp4... I chose smart movie player because it has more functionalities then nokia real player. try it.
More info: http://www.lonelycatgames.com/?app=smartmovieMessage Edited by m4dj on 25-Nov-200709:54 PM
Regards

ERROR! "There is not enough memory to open this scene."

I have a file that is proving impossible to reopen.
Whenever I open it i receive an error message that says
"There is not enough memory to open this scene. Your document is
not damaged and may be safely saved. To increase available memory,
close open documents or quit and use Get Info command in the Finder
to allocate more memory to Flash."
I have looked all over the internet for help and although
this seems to be a pretty popular problem, no one ever has a
solution. Some people claim it is because of a corrupt file they
tried to import. I don't have any files in the library of this
document and it is all completely vector.
I desperately need this file. Do have any ideas regarding
what I can do? Thanks a lot.

"thejublin" <[email protected]> wrote in
message news:e1bumn$92n$[email protected]..
> has anyone else ever received this error message?
You just posted that it seems to be a popular problem. We see
that complaint a lot, ever since MX2004 came out. Usually
associated
with the larger fla files.
Once the fla is corrupted there isn't a recover tool for it
(that I have heard of) You can start over or use a decompiler to
recover the pieces and code from it to use on your new one.
soThink swf decompiler can usually make a pretty good fla from a
working swf file (but not always)
tralfaz

'Not enough memory' when opening Excel, Word or ppt

When I try to open Excel, Word or ppt, I get a pop up box stating 'Not enough memory'.
I am running the latest update and through Disk Utility have done a repair disk.
HELP!
I have run a search on google to solve the problem but the solutions appeared far too 'techie'.
I can follow reasonable guidance but was lost even reading their proposed solution.
Any guidance much appreciated.
Thank you

Alec71 wrote:
Hi,
Thank you to those who have replied.
Problem remains unsolved.
Here is what I am running.
OS X Version : 10.8.2
Processor : 2.4 GHZ Intel Core 2 Duo
Memory : 4 GB 1067 MHz DDR3
Start Up Disk : Macintosh HD
Russa,
thank you for your post. I followed your advice and it states the memory is OK.
Grant,
thank you for your post.
I am using Microsoft Office 2008.
I used the Activity monitor to read System Memory to determine how much RAM is being used:
In response to your Questions:
Total Memory in the Mac = 4 GB
Free (Green) = 1.41 GB (1 third of the pie)
Wired (Red) = 733.7 MB
Active (Yellow) = 1.64 GB
Inactive (Blue) = 232.6 MB
Used = 2.58 GB
Page Outs = 0 bytes (0 bytes / sec)
Swap used = 0 bytes
Does anyone have any solutions now I have provided a bit more information?
Thank you, I can't function without being able to access word & excel.
Reinstall Office 2008.

CS2 Not enough memory when opening a file

When I try to open a EPS file in CS, I get the Not enough memory dialog but if I open it in the trial version of CS4, it opens easily and uses half the ram compared to CS2 before it brings up the dialog. Is there a fix for this for CS2?
Thanks
Ryan

Processexplorer and task manager, I have installed the update, using CS2 my machine grinds to a halt and doesnt open the image - CS2 ram usage when trying to open the image 690mb compared to cs4 trial 480mb with the image opening and barely any performance issues. Any image of 80mb seem to not open.

"Not Enough Memory" Error when programming Keithley 2400 using LabView 6i

I'm trying to use LabView 6i drivers to control a keithley 2400 via GPIB interface. Most of the drivers work fine but the high level operations such as a the sweep functions or even functions that perform a single measurement gives a "Not enough memory" driver error. What doesn't have enough memory? A single measurement can't overload the PC's or Keithley's memory buffer so why am I getting the error?
Thanks for any help you can offer...
Evan

Evan,
That's not a LabVIEW, GPIB, or NI-VISA error code - that error is generated by the instrument driver. I went ahead and downloaded this driver from keithley.com to take a look at this Perform DC VI.vi function's source. But unfortunately, the heart of the Perform DC VI function is a "Call Library Node" call to a keithley DLL, so that is a black box. Also, no c-source included that I could find, so I could not look at that either. And since I don't have a Keithley 2400 to play with, that brings me to the end of the rope on my system.
A couple of more things you could try, however, since you actually have the instrument.
(1) Definately build a simple VI to eliminate other aspects of your program. In this case, the most simple
VI would be an Init, Perform DC VI.vi, and then a close. Make sure this simple program reproduces the error. If it doesn't, then the problem is likely introduced in your code, not the driver.
(2) If #1 reproduces the problem, then check that you have all the driver pre-requisites correct (ie, that NI-VISA is installed, that the GPIB board is working properly, etc).
(3) If #1 and #2 do not result in any discoveries, then you will have to enter the black box of that DLL. Primary method to do that, to be honest, is to contact Keithley and ask for help, since they developed the driver. Second method is to use our NI-SPY utility, which can capture all calls to VISA drivers, (since this is a VXIpnp driver, it should be fundamentally using VISA within the DLL). Within NI-SPY, you will be able to see the individual function calls, and which ones are returning errors. That may help point in the right direction.
Regards,
Greg Caesar
National Instruments
Applications Engineer

Not enough memory to open file

I am unable to open a 1.7 mb file in photoshop 6. I had it opened about 3 weeks ago but made no changes. I downloaded a new copy of the file thinking my version was corrupted but no luck. I am running windows xp, 2.8 ghz celeron and just installed an additional 2gb of ram. Naturally, photoshop is the only program i had running after a restart aside from the minimal startup windows nonsense. Short of buying a mac or the latest version of photoshop, what can I do?
Many thanks for any input.
On a side note, I am able to open a 4.8 mb companion file to the one in question. Both are .psd files.

Just for giggles, are you updated to Photoshop 6.0.1?
http://www.adobe.com/support/downloads/product.jsp?product=39&platform=Windows
If that does not work, consider trying to open the file in GIMP (http://www.gimp.org) or any other image editing program that supports your image filetype.

Illustrator show not enough memory to open file,

but the file is only under 200k, my PC config is 16G Win 7, 1TB HD

no, the file is OK, I have test when the PC after restart, illustrator can open it one, but after open the same file, close then reopen the file by illustrator, it fail again, only have open the same file with illustrator, do not have open any program

Not enough Memory, .3ds 3D Layer

Excuse my english
System Spec:
PC 1
Phenom 2 (4x4 GHZ)
RAM 8GB 1333
Geforce GTX 275 1024MB
Scratch Disk - 40GB Raptor High Speed Disk unfragmented
PC2
Phenom 2 (4x3,2 GHZ)
RAM 4GB 1333
AMD Radeon 6870
Scratch Disk - 100GB unfragmented
Its nearly not possible for me to open any 3d objects i created in 3ds MAX, sometimes its able to open a simple 4 sides box, but that was it. No change to get something just remotely complexer than that box. Always the same "not enough memory to open Layer Error. It not even trys, i geht the error msg in about 10 ms after klicking.
I tried every preference setting i saw here on the forums. Turn open GL on / off, change the disc, more / less memory or VRAM, change opengl parameters and so on and so on. Im getting a little bit depressed from watching online tutorials where everyone is able to import even pretty complex polygon models into CS5, but not me....
Please Help

Check your export settings in MAX. I bet you are using features that are not supported by legacy 3DS files and that custom, MAX-only usable data is making things go haywire.
Mylenium

System 7.1 "not enough memory to open program"

Similar Messages

Maybe you are looking for