System log shows operating system call recv failed(error no.73)

hi all,
  here i have some doubt in system log please clarify me,
here in my (sm21)system log files i find more no  of logs for dispatcher and it indicates operating system call recv failed(error no.73)
system log  Short Text shows:
Operating system call &5&5&4 failed (error no. &>E5)
The specified operating system call was returned with an error.
For communication calls (receive, send, etc) often the cause of errors are network problems.
It could also be a configuration problem at operating system level. (file cannot be opened, no space in the file system etc.).
what is means

Hello,
Yes, you are right, these kind of problems (OS Error 73) are usually caused by network issues. Error 73 means 'connection reset by peer'. In most cases, this is because the connection was interupted by the communication partner or an active network component between.
I provide you some recommendations:
- Check your Network environment. You can use NIPING tool to diagnose it (note 500235), check your MTU stability.
- Check note 27320 - keep alive and gui_auto_logout profile param
- Also you can implement note 1002075 for a possible solution
I hope this helps you.
Regards,
Blanca

Similar Messages

  • I fail to start the sap server with error:Operating system call recv failed

    I fail to start the sap server in SAP R3 Management Console and the message in the syslog was :
    R/3 Basis System: Operating system call           recv failed (error no. 10053)
    Is there any one could tell me how to resolve the problem or give me some advice?I will appreciate him/her very much.Thank you.

    trc file: "dev_disp", trc level: 1, release: "620"
    Sun May 07 13:14:30 2000
    kernel runs with dp version 3(ext=1) (@(#) DPLIB-INT-VERSION-3)
    length of sys_adm_ext is 304 bytes
    systemid   560 (PC with Windows NT)
    relno      6200
    patchlevel 0
    patchno    674
    intno      20020600
    pid        3628
    ***LOG Q00=> DpSapEnvInit, DPStart (00 3628) [dpxxdisp.c   978]
         shared lib "dw_xml.dll" version 674 successfully loaded
         shared lib "dw_xtc.dll" version 674 successfully loaded
         shared lib "dw_stl.dll" version 674 successfully loaded
    Sun May 07 13:14:32 2000
    WARNING => DpNetCheck: NiAddrToHostCanon() took 2 seconds
    Sun May 07 13:14:37 2000
    WARNING => DpNetCheck: NiAddrToHost(1.0.0.0) took 5 seconds
    ***LOG GZZ=> 2 possible network problems detected - check tracefile and adjust the DNS settings [dpxxtool2.c  3212]
    MtxInit: -2 0 0
    DpShMCreate: sizeof(wp_adm)          12784     (752)
    DpShMCreate: sizeof(tm_adm)          1690816     (8412)
    DpShMCreate: sizeof(wp_ca_adm)     18000     (60)
    DpShMCreate: sizeof(appc_ca_adm)     6000     (60)
    DpShMCreate: sizeof(comm_adm)     192000     (384)
    DpShMCreate: sizeof(wall_adm)     (22440/34344/56/100)
    DpShMCreate: SHM_DP_ADM_KEY          (addr: 001E0040, size: 1977824)
    DpShMCreate: allocated sys_adm at 001E0040
    DpShMCreate: allocated wp_adm at 001E0560
    DpShMCreate: allocated tm_adm_list at 001E3750
    DpShMCreate: allocated tm_adm at 001E3778
    DpShMCreate: allocated wp_ca_adm at 00380438
    DpShMCreate: allocated appc_ca_adm at 00384A88
    DpShMCreate: allocated comm_adm_list at 003861F8
    DpShMCreate: allocated comm_adm at 00386210
    DpShMCreate: allocated ca_info at 003B5010
    DpShMCreate: allocated wall_adm at 003B5018
    MBUF state OFF
    Sun May 07 13:14:38 2000
    EmInit: MmSetImplementation( 2 ).
    <ES> client 0 initializing ....
    <ES> InitFreeList
    <ES> block size is 1024 kByte.
    Using implementation std
    <EsNT> Memory Reset enabled as NT default
    <EsNT> EsIUnamFileMapInit: Initialize the memory 2458 MB
    <ES> 2457 blocks reserved for free list.
    ES initialized.
    ***LOG Q0K=> DpMsAttach, mscon ( db01) [dpxxdisp.c   9115]
    CCMS: Initalizing shared memory of size 20000000 for monitoring segment.
    CCMS: start to initalize 3.X shared alert area (first segment).
    DpMsgAdmin: Set release to 6200, patchlevel 0
    MBUF state PREPARED
    MBUF component UP
    DpMBufHwIdSet: set Hardware-ID
    ***LOG Q1C=> DpMBufHwIdSet [dpxxmbuf.c   941]
    DpMsgAdmin: Set patchno for this platform to 674
    Release check o.K.
    Sun May 07 13:15:18 2000
    ERROR => W2 (pid 4776) died [dpxxdisp.c   11523]
    force unlock of wp_adm mutex W2
    Sun May 07 13:15:38 2000
    ERROR => W5 (pid 4548) died [dpxxdisp.c   11523]
    force unlock of wp_adm mutex W5
    ERROR => W8 (pid 4592) died [dpxxdisp.c   11523]
    force unlock of wp_adm mutex W8
    ERROR => W9 (pid 4584) died [dpxxdisp.c   11523]
    force unlock of wp_adm mutex W9
    ERROR => W12 (pid 4676) died [dpxxdisp.c   11523]
    force unlock of wp_adm mutex W12
    ERROR => W13 (pid 4272) died [dpxxdisp.c   11523]
    force unlock of wp_adm mutex W13
    my types changed after wp death/restart 0xbf --> 0xb7
    Sun May 07 13:15:58 2000
    ERROR => W4 (pid 4888) died [dpxxdisp.c   11523]
    force unlock of wp_adm mutex W4
    ERROR => W6 (pid 4788) died [dpxxdisp.c   11523]
    force unlock of wp_adm mutex W6
    ERROR => W15 (pid 4596) died [dpxxdisp.c   11523]
    force unlock of wp_adm mutex W15
    Sun May 07 13:16:18 2000
    ERROR => W1 (pid 4892) died [dpxxdisp.c   11523]
    force unlock of wp_adm mutex W1
    ERROR => W3 (pid 4904) died [dpxxdisp.c   11523]
    force unlock of wp_adm mutex W3
    ERROR => W7 (pid 4000) died [dpxxdisp.c   11523]
    force unlock of wp_adm mutex W7
    ERROR => W10 (pid 4864) died [dpxxdisp.c   11523]
    force unlock of wp_adm mutex W10
    my types changed after wp death/restart 0xb7 --> 0xb5
    Sun May 07 13:16:38 2000
    ERROR => W0 (pid 4900) died [dpxxdisp.c   11523]
    force unlock of wp_adm mutex W0
    ERROR => W11 (pid 4500) died [dpxxdisp.c   11523]
    force unlock of wp_adm mutex W11
    ERROR => W14 (pid 4636) died [dpxxdisp.c   11523]
    force unlock of wp_adm mutex W14
    ERROR => W16 (pid 3532) died [dpxxdisp.c   11523]
    force unlock of wp_adm mutex W16
    my types changed after wp death/restart 0xb5 --> 0x80
    DP_FATAL_ERROR => DpEnvCheck: no more work processes
    DISPATCHER EMERGENCY SHUTDOWN ***
    DpModState: change server state from STARTING to SHUTDOWN
    Sun May 07 13:16:42 2000
    ***LOG Q0M=> DpMsDetach, ms_detach () [dpxxdisp.c   9341]
    MBUF state OFF
    MBUF component DOWN
    ***LOG Q05=> DpHalt, DPStop ( 3628) [dpxxdisp.c   7883]

  • Error in BW ( Operating system call SiPeekPendConn failed )

    Hi All,
    This is Ganesh, new to SAP BASIS. We are facing some errors in BW, where users cannot able to run BW reports from yesterday.
    Please find below system log details:
    Operating system call recv failed (error no. 10054)
    NiConnect Unsuccessful, Return Code: -0010
    > Host: 156.5.30.34
    > Service: sapgw00
    Please help me out by providing the solution and the cause for above system log.
    Waiting for your reply.
    Best Regards,
    Ganesh

    Hi,
    check this,
    http://sap.ittoolbox.com/groups/technical-functional/sap-bw/sap-r3-to-bw-521356#M521423
    Also try to search with the error ur getting in Google or for Notes in SMP.
    Regards,
    Ravi

  • System Image Utility Failing Error 2 Yosemite

    I'm trying to create an net install image of the OS X Yosemite installer. It worked with 10.0, now on 10.0.1 I'm getting an error "System Image Utility Failing Error 2". I've tried it a few different ways but I get the same result every time. Has anyone been able to create a 10.0.1 image?

    After doing all that I described in my previous post three things happened:
    1. I need to proof read better mi writing (I am fluent in english but of course is not my native language).
    2. The NetInstall image I created did work!, but it failed at 99.99% verifying leaving a useless installation. I was able to bring back some computers by reinstalling only the system, but most of them had to be erased and reimaged again.
    And number 3:
    I found another solution that worked fine this time. !!!
    (well, it had a hiccup but not a show stopper)
    What is needed:
    - A known working NetInstall image.
    Steps:
    1. Copy the NetInstall.nbi folder to another location.
    2. Using Disk Utility convert the image file NetInstall.dmg (inside the NetInstall.nbi) to a read/write image, preferably to a sparse image.
    3. Mount the new image and locate the folder 'Packages' inside it (it is invisible in the Finder).
    4. Remove System.dmg
    5. Copy your source image on the same place and make sure it is named System.dmg and is of type read-only / compressed. (If the new image is bigger than the one before, it will be useful that the NetInstall.dmg be a sparse image.)
    6. If the source image was not previously scanned for ASR, do it now.
    7. Unmount the NetInstall disk
    8. Using Disk Utility convert your new NetInstall.dmg to read-only / compressed.
    9. Rename your NetInstall.nbi to YourNewNetInstall.nbi
    10. Edit the file NBImageInfo.plist (inside the YourNewNetInstall.nbi)  and locate the line with the old name of the .nbi and change it to the new one. Locate the "Index" and change it too (maybe simply add 1.) Also, change the line that mentions the System version and change it to the one that the new NetInstall contains (up to only the first decimal.)
    11. Move back YourNewNetInstall.nbi to the NetBootSP0 folder where it came from.
    12. In Server activate your new NetInstall source (you can change the index there too) and update the computers list it will be served to.
    Ready!
    Using this I could reinstall the computers without a problem this time.
    Ok, I said there were a hiccup:
    After finishing, the computers restarted to their recovery partition and a simple restart brought them back to it. Using Disk Utility and verifying the disk was enough to restart them properly.
    Hope this helps.
    Greetings from Mexico!
    Alex Ramos

  • Socket operation on nonsocket: recv failed

    I get this Exception when operating with Socket : Socket operation on nonsocket: recv failed
    What does this exception mean?

    Looking on google,
    http://www.google.co.uk/search?num=20&hl=en&c2coff=1&q=+Socket+operation+on+nonsocket%3A+recv+failed+&btnG=Search&meta=
    this appears to be a windows error
    http://msdn.microsoft.com/library/default.asp?url=/library/en-us/winsock/winsock/windows_sockets_error_codes_2.asp

  • "Operating system file operation on file IFile failed" error.

    Hi there,
    Does someone got a clue about the error "Operating system file operation on file IFile failed" occurring from time to time when scheduling Webi and Deski reports?
    This occurs on a cluster environment with 2 servers (BOXI R2 SP2).
    Regards,
    Jeff

    Hi Jeff,
    -This error is usually associated with the system not being able to access the FRS when
       BOE is trying to read the report.
    -Also, could you please check that your document names should not have dot (.)
    -It's also possible this could be permissions related could you please monitor the
       system for any 'access denied' results and see if this is related to permissions.
    Regards,
    Sarbhjeet Kaur

  • How can I change the default message after System Call Handler transfer error?

    Hi,
    I'm using Unity Connection 9.1 and System Call Handlers to allow to join internal extensions (not reachable from the PSTN).
    I succeeded but I would like to change the default message played when the extension dialed is not known. I tried with Error greetings but nothing changed.
    Thanks for your help.
    Regards,
    Julien

    Just tried this on my 9.1 and 10.0(1) servers and it worked fine.
    I went to the opening greeting call handler, selected the "error" greeting, set the greeting to play my personal greeting (it defaults to the system generated greeting), recording "hey, you dialed the wrong number" and then called in and during the opening greeting I dialed "88" - I heard "hey, you dialed the wrong number" and then it repeated the opening greeting recording as it should.
    the default action after playing your custom greeting in this case is to "restart greeting" - which is why the opening greeting plays again.
    Not sure what you did in your testing with the error greeting - check to make sure you have it set to play your personal greeting instead of the default system greeting - since you can't disable the error greeting there's not a lot of other items I can think of to check.

  • The ADS call has failed - Error

    Dear all
    I have created one web dynpr application with interactive forms followed by saptechical.com, If i run the web dynpr application, it thrown an error
    "WebDynpro Exception: The ADS call has failed. You can find information about the cause in the error.pdf on the application server"
    I have checked standard prog. (FP_PDF_TEST_00) for checking ads connection, thats working fine. It shows a forms.
    But if i run my custome web dynpro application, it shows error.
    Please give a solution.

    Hello,
    please also check:
    FP_TEST_00
    and
    FP_TEST_IA_01
    these also have to work in order to render interactive PDF inside a Webdynpro ABAP application.
    I assume:
    1. You do not have proper destination service configuration. (described in note: #915399)
    or:
    2. The credential is not properly installed into your ADS.
    Please ensure the credential is installed, the expiry date is visible and the J2EE engine was restarted after the credential has been installed.
    Best regards,
    Dezso

  • System Image Utility Failing Error 2

    I've built my 10.9.4 gold image on a Macbook Pro, created the image with SIU and deployed successfully to the other Macbooks.   When I went to deploy to the iMacs we have I get the error OSX Could not be installed on your computer.  Did some research and found I needed to install the Combo update if I wanted to deploy to multiple hardware, so installed OSXUpdCombo10.9.4  into the gold machine. Now I can no longer import that with System Image Utility.
    System Image log looks like:
    "/Library/NetBoot/NetBootSP0/IMG-OXL-1094-All.nbi/System.dmg"
    created: /Library/NetBoot/NetBootSP0/IMG-OXL-1094-All.nbi/NetInstall.dmg
    ditto: can't get real path for source '/tmp/mnt_bs.aLkzKL2z/System/Library/CoreServices/PlatformSupport.plist'
    Execution of 'createRestoreFromSources.sh' failed. Cleaning up.
    "disk5" unmounted.
    "disk5" ejected.
    Failed to create image from restore source.
    The operation couldn’t be completed. (System Image Utility error 2.)
    Looks like this can happen if the version of Mavericks on the server and client don't match.  So I've installed the combo updater on the server for good measure.  Still getting the same error.
    Server reports it is running 10.9.4 (13E28),client says the same.
    Any idea where to look next?

    Went back through my notes, I read that you should run the 10.6 combo updater before trying to image, and somehow decided that meant 10.9 :/
    Thanks for the info, that makes sense.  I've had to make separate images for each model this round, but I'll add that info to my notes and do it right next time
    Jase

  • The share operation master file has failed error -1

    I can not export.  I keep getting this message.  Can anyone help me?  I am running Final Cut Pro X.

    curtoy222 wrote:
    I can not export. 
    You can't export…a specific project…or any project…choosing a specific Share destination…or any Share destination?
    What are your system specs – and where do you have your events and projects stored?
    What format is the media you're using?
    Russ

  • Error on WAS no. 10054 SAP Basis System: Operating system call

    Hi All,
    Error on WAS no. 10054 SAP Basis System: Operating system call
    we got the following error message in the syslog of the WAS:
    SAP Basis System: Operating system call  recv failed (error no. 10054)
    The system still works. What can we do?
    Thanks.
    Best Regards,

    Hi,
    Please check the folloiwng notes
    Error no. 10054
    34116 - Syslog: "Operating System call xxxx failed"
    Thanks
    Adil

  • Work Process tries to restart but fails - Operating system call fork:restar

    Hi
      We have a ECC 5.0 system running on v5r4 (6.40 kernel level 159).  Some of the work processes fail and then try to restart and fail again. Thus there are many job log entries in both SAP and OS/400.
    The OS/400 logs mention the PASE (unix executable environment) and MCH3203.
    SAP mentions Operating system call fork:restart
    OSS has note #884359 which mentions a palitative but despite being at 6.40 level 159 the parameter profile as/4/wp_max_restart is said to be "unknown" by RZ10.
    We are making sure we are up to date with the APAR II14126 just in case this is the issue.
    It did start after the time change but we are not sure this is the root cause.
    We are also considering getting upto kernel 171.
    Anyone else seen this issue?
    thanks
    Matthew Milne

    We see those problems once a while, and usually they are gone when you restart the instance or after an IPL. You should report the problem to IBM, they will probably be interested in the LIC log entries that come along with the error (STRSST - Start a Service Tool - Licensed Internal Code Log). II14126 is probably a good start (for example, MF40759).
    The profile parameter as4/wp_max_restart is only known to the kernel, because it is not intended as a permament setting, but only as a temporary workaround for the problem in the PASE environment. That's why RZ11 does not know about the parameter and reports it as unknown.
    Kind regards,
    Christian Bartels.

  • MDT 2012 - Failed to Run Action: Install Operating System Access is Denied (Error: 0000005; Source: Windows)

    Unable to deploy any image with WIM file. Vanilla or Custom Image gives the following error:
    ZTI Error – Unhandled error returned by LTIApply: invalid procedure call or argument (5)
    Litetouch deployment failed, Return code = -2147467259 0x80004005
    Failed to run action: Install Operating System.
    Access is denied (Error: 00000005; Source: Windows)
    Tried Giving Everyone Full rights to the deployment share
    Rebooted Server
    Updated Deployment Share
    Any ideas would be great!
    Thanks
    Rick
    Richard Ray

    https://skydrive.live.com/redir?resid=57E5397C8C507949!129&authkey=!AJDCfz7nGblrdQE&ithint=folder%2c.log
    Please try this link.
    Kris Da San Martino
    The SMSTS.log shows
    Expand a string: WinPEandFullOS TSManager 2/18/2014 1:35:48 PM 1508 (0x05E4)
    Executing command line: cscript.exe "%SCRIPTROOT%\LTIApply.wsf" TSManager 2/18/2014 1:35:48 PM 1508 (0x05E4)
    Process completed with exit code 5 TSManager 2/18/2014 1:51:00 PM 1508 (0x05E4)
    !--------------------------------------------------------------------------------------------! TSManager 2/18/2014 1:51:00 PM 1508 (0x05E4)
    Failed to run the action: Install Operating System.
    Access is denied. (Error: 00000005; Source: Windows) TSManager 2/18/2014 1:51:00 PM 1508 (0x05E4)
    Sending status message . . . TSManager 2/18/2014 1:51:00 PM 1508 (0x05E4)
    Executing in non SMS standalone mode. Ignoring send a task execution status message request TSManager 2/18/2014 1:51:00 PM 1508 (0x05E4)
    Set a global environment variable _SMSTSLastActionRetCode=5 TSManager 2/18/2014 1:51:00 PM 1508 (0x05E4)
    Set a global environment variable _SMSTSLastActionSucceeded=false TSManager 2/18/2014 1:51:00 PM 1508 (0x05E4)
    Clear local default environment TSManager 2/18/2014 1:51:00 PM 1508 (0x05E4)
    Let the parent group (Install) decides whether to continue execution TSManager 2/18/2014 1:51:00 PM 1508 (0x05E4)
    The execution of the group (Install) has failed and the execution has been aborted. An action failed.
    Operation aborted (Error: 80004004; Source: Windows) TSManager 2/18/2014 1:51:00 PM 1508 (0x05E4)
    Failed to run the last action: Install Operating System. Execution of task sequence failed.
    Access is denied. (Error: 00000005; Source: Windows) TSManager 2/18/2014 1:51:00 PM 1508 (0x05E4)
    Sending status message . . . TSManager 2/18/2014 1:51:00 PM 1508 (0x05E4)
    Executing in non SMS standalone mode. Ignoring send a task execution status message request TSManager 2/18/2014 1:51:00 PM 1508 (0x05E4)
    Execution::enExecutionFail != m_eExecutionResult, HRESULT=80004005 (e:\nts_sms_fre\sms\client\tasksequence\tsmanager\tsmanager.cpp,767) TSManager 2/18/2014 1:51:00 PM 1508 (0x05E4)
    Task Sequence Engine failed! Code: enExecutionFail TSManager 2/18/2014 1:51:00 PM 1508 (0x05E4)
    **************************************************************************** TSManager 2/18/2014 1:51:00 PM 1508 (0x05E4)
    Task sequence execution failed with error code 80004005 TSManager 2/18/2014 1:51:00 PM 1508 (0x05E4)

  • Zones not booting - failed to create devlinks: Interrupted system call

    I just installed the latest 10_Recommended cluster with 118833-36 kernel patch and now my zones won't boot. I get the error:
    (root)Yes Master?> zoneadm list -iv
    ID NAME STATUS PATH
    0 global running /
    - samba installed /export/home/zones/samba
    - web installed /export/home/zones/web
    - dhcp installed /export/home/zones/dhcp
    - dns installed /export/home/zones/dns
    - vs1 installed /zdata/zones/vs1
    - dss installed /zdata/zones/dss
    - test installed /zdata/zones/test
    (root)Yes Master?> zoneadm -z test boot
    failed to create devlinks: Interrupted system call
    console setup: device initialization failed
    zoneadm: zone 'test': could not start zoneadmd
    zoneadm: zone 'test': call to zoneadmd failed
    Also, running devfsadm or drvconfig;devlinks from the global zone will core dump.
    Any ideas..??
    tia..

    First, you gotta change your prompt to something less embarrassing when you post to a public forum :)
    I'd forget about the zones problem and focus on why devfsadm core dumps -- that's the core of the problem (no pun intended...no, really!).
    First, review the install logs of all the patches installed during the recent service (/var/sadm/patch/*/log). Even if they all show a good completion, check the messages they generated, sometimes they have errors that aren't bad enough to cause a complete failure of the patch. The KJP (118833-36) is probably a good one to start with.
    Next I'd "truss" the devfsadm command while it core dumps then get a stack trace of the core (run "adb <corefile>" and type "$C" -- that's old school, I'm sure mdb is much cooler...).
    Throw some of the strings from those against sunsolve and see if something sticks.
    Good luck!

  • Error during installation of ECC6- system call failed

    Dear all,
    i encounter the error as below during sap installation. its looks like the ID issue, but this id (fbqadm) is using by me to log into the windows. please help me.
    thank
    ERROR      2009-03-17 10:07:25.583 [syxxsyshlp.cpp:78]
               syslib::printOSError(const iastring &, int, DWORD, const iastring &, CMessage::eLogMessage)
    FSL-00001  System call failed. Error 1326 (Logon failure: unknown user name or bad password.
    ) in execution of system call 'LogonUser' with parameter (fbqadm, SAPFBWDEV01, *******, LOGON32_LOGON_INTERACTIVE,LOGON32_PROVIDER_DEFAULT,&hUserToken), line (1014) in file (synxccuren.cpp).
    TRACE      2009-03-17 10:07:25.813 [iaxxejsbas.hpp:408]
               handleException<ESyException>()
    Converting exception into JS Exception ESyException.
    TRACE      2009-03-17 10:07:25.813
    Function setMessageIdOfExceptionMessage: modlib.jslib.caughtException

    problem fix after reboot the server

Maybe you are looking for

  • Installed Debian Linux over my entire hdd. how to reinstall os x?

    I installed Debian linux for ppc over my entire system using a usb drive. OS x is gone. How do I get it back? My internal optical drive doesn't work. I put the Tiger install cd that came with the computer into my second computer macbook in target mod

  • Top 11 instead of Top 10

    Hello! I have a Report with the following objekts in report: Part No. Dealer Sales I have a Top N condition on Part No. depends on Key Figure Sales. But sometimes I have 11 values and Top 11. This 11. value is indeed the 152. value. If I take Dealer

  • Profit center wise credit/debit calculation

    Hi, SAP guru's My vendor have required profit center wise cedit/debit calculation. I did this coading but in gt_list it append one blank line.due to this when i want to calculate the final debit credit it wont give proper value.please help me... SELE

  • WebService Call Fails for Communication Users

    Hi I am calling a BAPI through web service in VB.NET windows application. The application works fine with Dialog users but when I use Communication User then it thows this message. The Request Failed with HTTP Status 401: Unauthorized Where as if i c

  • How do I a create a PDF of an individual page that is in a PDF already?

    Hi there, I'm trying to create PDFs of individual pages within this PDF document online: [url deleted by host] How do I do this? Thanks. Sarah