Tecra R850-1HU: how to connect 4 external microphones

Hello
I need to have the sound out to an amplifier and i need to put 4 microphones through a mixing table als input.
How can we do that with *just 1 mini jack (* any adapter to 2 mini jack??)
Thanks for any help

Hi
Never tried to use 4 microphones but I think you will need to use an external device, something like 4 channel microphone mixer but I think this forum is the wrong place to talk about such themes since this is not really related to the notebook but to DJ equipment.
However, please share your experience with us after you have managed to connect 4 mic to the notebook.

Similar Messages

  • How do I connect an external microphone to a Macbook Pro with Retina display ?

    How do I connect an external microphone to a Macbook Pro with Retina display ?
    Alternatively how do I connect an audio input at a level that would normally have gone into a 'line input' socket ?

    Plug it into the linein/headphone jack if there's just one.  It'll switch between the two modes automatically depending on what you plug into it.

  • How to connect an external monitor to macbook pro. The monitor has no usb connector without a usb

    How to connect an external monitor to macbook pro. The monitor has no usb connecter, only a port.

    Most MacBook Pro models have a Mini DVI port, a Mini DisplayPort or a ThunderBolt port for connecting an external display. USB does not have enough bandwidth to support a responsive display connection.
    What model MacBook Pro do you have, by year, CPU speed or MacBook Pro 3.1 designation?

  • How to connect two external monitors to a Mac Book Pro?

    How to connect two external monitors to a Mac Book Pro?

    Not as is, but  Matrox makes a peripheral that enables connecting more than one external monitor - matrox.com.

  • How to connect an external hard drive and monitor a single port thuderbolt

    how to connect an external hard drive and monitor a single port thuderbolt

    Yu connect the HDD to your Mac and then the monitor to the HDD.
    The HDD  should have TWO T-Bird ports on the enclosure.
    Its called daisy chaining and up to five devices can be connected in this fashion.

  • How to use an external start button for 6024E w/ sc-2345, I would like it to function like a start button in LabView but I don't know how to connect the external button to the sc-2345's connector block

    I am confused as to how to connect my external start botton. I would like it to function like a start button on a front panel of a VI. I would like to use the +5V on pin 14 but I really don't know where to go from here. Any guidence for a novice would be most appreciated.

    phod,
    This is the LabVIEW Real-Time forum, so I suggest that in the future that you post this type of question to the Multifunction DAQ forum.
    For the simplest solution you will have to connect your button to a digital line of your board, consult the sc-2345 user manual for a diagram of where these lines are exposed. You will have to connect your start button in series with a line that is high, such as your 5V pin or another digital line. Then connect this to a digital line that will be your start trigger.
    Your program can poll the digital line that is connected to your button in a while loop and when it goes high, it lets the rest of the program execute. For the programming, I suggest you take a look at the shipping examples that come with LabVIEW. If yo
    u have LabVIEW 7.0 go to Help>>Find Examples. Open Hardware Input Output>>Traditional DAQ>>Digital Input and Output>>E Series for some examples of digital I/O programming with E-series boards.
    Hope that gets you started.
    Gerardo

  • How to Connect my External WD Passport hard disk using wifi

    Dear Friends,
    i have got a new Apple Ipad 4 Gen, of 16GB but now i am facing a problem due to space requirements.
    my ipad is filling with lots of photoes and music.right now only 750mb is available among 16GB. i have an idea ,i need to connect my
    External WD Passport hard disk of 1TB using wifi router. and acess the same with my ipad.for transferring photoes and music and videos
    data e.t.c to and from Ipad.please tell me is this possible with my existing WD hard disk and i am ready to take a new rouer. and how to use this.
    thanks in advance
    Regards
    Krish

    You can play your music from computer to iPad using Home Sharing.
    Understand Home Sharing
    http://support.apple.com/kb/ht3819
    Setting Up Home Sharing on IOS Device
    http://support.apple.com/kb/ht4557
    Setting Up Home Sharing on Computer
    http://support.apple.com/kb/ht4620

  • How to connect to external web service and convert XML to a table

    Hi experts,
      I need to connect to external/non-SAP web service and convert XML in that site to a SAP table?
    Is there a function call(SE37) to do this? Is it a must for me to install AS JAVA or PI and configure enterprise service? Please provide a link for me to retrieve relevant infomation, thx.

    No, you don't need PI or the Java stack for this.  You can create an ABAP proxy using the WSDL file for the web service and call the web service using the proxy class in an ABAP program.  You can transform the XML response to internal tables/structures/variables using a transformation template that you create.

  • Does anyone know how to connect an external zoom to a canon FS20 camcorder.

    Is it possible to connect an external zoom remote to a canon FS20 camcorder?  With no LANC port i would assume those controllers are out... anyone know of a different controller/ remote that might work?  I want to use the camera on a taller boom to tape soccer games but i am concerned that there is no way to zoom in.

    Hi cardsdude2015! Without a remote port or even a wireless remove sensor (like the FS22 has), it is not possible to use a remote with the FS20.

  • How to connect an external HD to a 2007 Mac Mini with FireWire

    I have a 2007 Mac Mini with a 1.83 GHz Intel Core Duo processor, 1 GB of RAM, and an 80 GB HD. I recently migrated to Snow Leopard (OS X 10.6.5) from Tiger (OS X 10.4.11). I purchased a 500 GB external HD from Seagate which I want to use to back up both my wife's notebook PC and my Apple. My Mac Mini has a Firewire 400 (6-pin) female connector on the back. The external HD can connect to a Mac via a Firewire 800 male 9-pin connector. How do I connect the male FW 800 9-pin to the female FW 400 6-pin port? This may sound obvious, but the solution is more challenging than I imagined. The 9- to 6-pin adaptors I've seen online combine a female 6-pin end with a male 9-pin end. I need the reverse of that (female 9-pin FW 800 to male 6-pin FW 400 adaptor)! I bought a 9- to 6-pin cable this week, but ended up with two male 9-pin plug ends, and no way to connect them. Is a solution available using FW, or should I bail and go with a USB 2.0 connection instead?

    Most external firewire drives have removable cables that plug into "female" ports on the hard drive. Is the firewire cabling on your external drive different from this? (What is the model number of the external drive?)
    If the cable is removeable, simply buy a 6-pin-to-9-pin firewire cable (male on both ends).
    monoprice.com is a good place to find these cheaply and in the length you need.

  • How to connect to external server using router from VLAN's

    Hi, I am newbie. I am trying to build network system in Packet Tracer.
    Now I have such network layout.
    I have different VLAN's Accounting and Sales. I have configured this using subinterface in router to allow computers from different vlan's communicate with each other. Everything works.
    Let's assume that there are next subnets and VLAN's. Acct. VLAN (2) (ip's 172.168.0.1-172.168.0.254/24) and Sales VLAN (4) (ip's 172.168.1.1-172.168.1.254/24).
    But I need to connect all this computers to the external server.  That has ip , for instance 192.168.20.13/24. Like this.
    I don't know hot to correctly configure router to make it possible for computers to connect to this server. I have connected switch to the another router interface. And than connected server to the switch and specified ip 192.168.20.13/24. Than I tried to set ip to the router interface from the same subnet like 192.168.20.22/24. So now router can communicate with server.
    But how to allow computers to communicate with the server. Please help. I am newbie.
    I would be grateful for any help.

    Hi Androgen,
    One question for you..How does the sales VLAN computers communicate with the accounting VLAN machines? It's through the inter-VLAN routing that you have already setup.
    Communicating to the external server is also similar to this.
    The computer's in the VLAN should be configured with the default gateway IP which is the the L3 sub-interface IP for that subnet.
    Also, the external server needs to have a default gateway to communicate with other remote subnet. The default gateway of that server would be 192.168.20.22 which is the L3 interface for your external subnet.
    CF

  • How to connect to External Web Service? Error: ICM_HTTP_CONNECTION_FAILED

    Hi all,
    I have created an External Web Service, and I am trying to call the web service from SAP. I watched some tutorial and did everything like them, but I am getting this error:
    SOAP:1,023 SRT: Processing error in Internet Communication Framework: ("ICF Error when receiving the response: ICM_HTTP_CONNECTION_FAILED")
    Can someone tell me how to solve this problem ?
    Thank you in advance

    Your AS ABAP is unable to connect to the remote server, talk to your network admins.

  • How to connect to External Database, if say SQL server, from Adobe LC

    Hi everyone,
    I have one application, which needs to save and load data from/to an external database,SQL server.I have no idea on how to implement this.But with my knowledge I managed to create DSs and using new data connection wizard, some how I managed to list the fields in the Data View.BUT i still worrying about the way i did is rigt or wrong?.. how can i save and load data to sql server from Adobe LC..Please help me
    Thanks,
    Vinod

    You created the data source on the app server which is the first step. Now you can use the JDBC service to query the database:
    http://livedocs.adobe.com/livecycle/8.2/wb_help/000632.html
    scott

  • How can connect to external speakers?

    How can I connect a MacBook Air to external speakers?

    Thanks for your help, Captfred.
    Will my sound output window detect the external speaker system, then?
    Right now the output only has "Internal Speakers" listed.
    The system I was connecting to had a jack -- would there be a Mac-specific jack?  (Similar to the VGA adapter I need?)
    Thanks again!

  • How to connect an external disk to time capsule?

    Hi,
    I've just connected my new external disk 2TB to the time capsule device. However, it doesn't show in the disk tab in Airport express. Yes, of course the disk is on, it's hfs+journaled formatted and works fine when connected directly to my usb port on my MacBook Pro.
    Any suggestion, please?
    Thanks.

    Unless this is a really new feature, Airport Express doesn't support external USB disks; only USB printers.
    The Wireless-N Time Capsules and Airport Extremes support external USB disks.

Maybe you are looking for

  • Creation of new condition type: MWST

    Hi, Everyone. I would like to ask for some help regarding this issue: Creation of new condition type: MWST with the following details: 1. For the country French Polynesia, Create a new VAT condition of 10%. 2. Create a new one called : Class : Z u201

  • Transport Manually

    Hi Friends, Recenlty i made some changes in dev to transport, but i tried with several changes with several request and i released all those request. Now the problem is i don't know what is my acutal request no to transport. The changes i have done a

  • Spry Master Detail section not showing in IE after addObserver

    So, I have this cool thing almost done and I get it close and then it goes blank in IE - FireFox is fine, Safari PC is blank, Chrome is blank too. http://ryanmillsdesignstudio.com/MasterDetail.cfm As soon as I add the addaobserver <script type="text/

  • Exchange 2007 to Exchange 2010 Migration

    Hi all, I am migrating to exchange 2007 to exchange 2010 .This is not a migration data only migration like i am exporting mailboxes and importing it to new mailboxes .But email address and SAM account name will be same as per the source.Post migratio

  • Windows 7 64bit BSOD

    Hi - my Windows 7 machine recently began crashing very frequently.  It worked fine for two years. I am hoping some smart person here can help me out? dump files: http://sdrv.ms/KuVKFJ Motherboard Asus X58 Sabertooth CPU i7 950 RAM 24 GB What I've don