Third party USB cable detected by IOS 7 update

Yesterday I had a working Ipad2 and foolishly I allowed it to update itself. Big mistake!
After all sorts of hangs, reboots etc I got it working again and then watched the battery drain before my eyes. Charged it overnight and after 12 hours it was at 75% and just about holding at that level. I have a third party USB cable and I borrowed my daughters OEM cable. When I plugged that in I could immediately see that it was charging normally BUT it also immediately disabled rotation and it is now stuck in landscape mode. I've tried switching the lock button to "Lock Rotation" and I see the icon on screen changing from locked to unlocked but it will not rotate. WHAT THE..............
Detecting that I am using a cable purchased from another source and deliberately disabling my property without my authority borders on the criminal.
Apple need to get it sorted.

I'm sure Apple would love for you (and everyone else) to use their cables...that's a given. But I seriously doubt that any kind of intentional "crippling" would be done to anyone's unit in some way because they used a third-party cable. Seems like the way it's setup now, if a third-party cable is detected, you'll get an on-screen message that the cable is detected as such and you may have issues when using it.
Try the cable again and if it faults the rotation function in the same way, then you can decide if you want to continue using the cable if it is indeed causing this same fault consistently. Otherwise, it could have just been a coincidence.

Similar Messages

  • Third-Party USB to Ethernet Adapter not working since 10.8 updated

    Hi I have a third-party USB to Ethernet adapter. Since the update of mountain lion the adapter does not work.
    Is there a driver or something I can do to make it work?
    Thanks

    USB not so good, this very good.
    Thunderbolt to Gigabit Ethernet Adapter

  • Are Any Third Party Lightning Cables Approved by Apple So They Work?

    Over the past year Apple made some iOS change that causes most third party Lightning cables to generate the error message "This cable or accessory is not certified and may not work reliably".  However, Apple has never clarified whether ANY third-party cables are approved and will work.
    Even most third party cables sold by the US primary cellphone carrier stores no longer work.
    Some third-party cables work for a partial recharge, however, won't charge the iPhone if it automatically shuts down due to low battery power.
    QUESTION
    Does anyone know if any third-party Lightning cables are approved by Apple and will charger phones after an automatic low battery shutdown?

    http://store.apple.com/us/product/HB558ZM/A/belkin-65-ft2-m-lightning-to-usb-cha rgesync-cable?fnode=45
    http://store.apple.com/us/product/HB560ZM/A/belkin-21-amp-lightning-to-usb-charg esync-cable?fnode=45
    http://store.apple.com/us/product/HB557ZM/A/belkin-6-21-amp-lightning-to-usb-cha rgesync-cable?fnode=45
    http://store.apple.com/us/product/HB561ZM/A/belkin-6-chargesync-cable-kit-lightn ingmicro-usb30-pin?fnode=45
    Plus Apple's own of course, and they tend to carry many more in the brick and morter stores.

  • How to use third party usb 485 interface

    I have a third party usb-485 interface that we frequently use within our company and want to be able to use Labview to create a program to talk to our systems. The interface is a kk systems usb-rs485 isolated converter which I have been able to recognise in MAX explorer after using the NI VISA driver wizard but I am unsure how to now use it for 485 comms within Labview. I don't seem to be able to detect it with the VISA configure serial port vi. I have used the NI usb-485 interface before and found this quite easy to set up but am not sure how to use this third party interface. I have attatched screen shots of the MAX window to show what it is seeing. Any help would be greatly appriciated.
    Attachments:
    MAX usb 485 screen shot.PNG ‏102 KB
    MAX usb 485 screen shot2.PNG ‏120 KB

    I have undone everything as recommended and the comm port does appear in the devices tree but when I try to use the device I don't seem to be able to get any response even though I can select the port as the VISA device name in my vi. I am pretty sure I have the baud rate etc.set the same as when we use the interface in other software,is there something else I need to do? I am using the rs485 example in labview as my code which works with the ni-usb485 we have. 

  • MacBook Pro with Third Party USB External Modem ? Drivers? Network Pane?

    I bought my brother a MacBook Pro last month, and he is using it fine in Pakistan with my Airport base station and cable internet access. Problem is when he is on the road, and using GPRS with his Sony Ericsson P900/910 is terribly expensive there. So, I have to send him an Apple USB modem (that I am yet to hear good things about). However, he does have an external third party USB modem that works fine with PC laptops. Are there any generic drivers for USB modems built into OS X in MacBooks? How would he go about using the external USB modem in Network control panel and using a generic driver?
    Is there a way to use Parallels (that he has) to connect to Internet from the Windoze USB modem and have MacOS X use the Windows connection as the "router"? Thanks.
    Imran

    No answer received. Closing to reduce clutter.

  • Error 1073807302 while connecting a third party USB device,and showing invalid setup

    While connecting a third party USB device,In NI MAX it is showing error 1073807302,Unable to start operation because setup is invalid,and error 1073807246 Object Reference is Uninitialized,in the USB settings Tab it is showing no pipe present in Bulk in pipe and in VIEW ATTRIBUTE Tab it is showing invalid property....
    please kindly reply me.....!!!

    sir,without configuring in NI-MAX how can we open a connection to VISA.
    If i install the device driver provided by supplier,i am not able to view my device in NI-MAX,so that, I had created and installed .inf file for my device using VISA driver wizard, In NI-MAX now I can see my device and its properties in visa interactive control.But it was showing some errors(Error-1073676418,error-1073807302,error-1073807298),in the USB settings Tab it is showing, "No pipe present in Bulk In-pipe", and in VIEW ATTRIBUTE Tab it is showing invalid property.In program it is showing error 1073807302,Unable to start operation because setup is invalid,and error 1073807246 Object Reference is Uninitialized,
    While Searching in ni.com, some one posted that change the USB Alternate settings to 1/2/3,default value is 0,but now also my problem is not solved.
    I am using VIATOR USB HART modem, Model 010031.

  • 3rd party USB cable

    Just a note to be careful with 3rd party USB cables and the iPad. I have one that works fine with an older iPod, but causes serious issues when used with my iPad. It causes disconnects during syncing and even causes several restarts of my iPad.
    Definitely stick with the original cable.

    David_o99 wrote:
    Just a note to be careful with 3rd party USB cables and the iPad. I have one that works fine with an older iPod, but causes serious issues when used with my iPad. It causes disconnects during syncing and even causes several restarts of my iPad.
    Not surprising as the dock connector changed after the early iPods. Your iPod could easily be one from the older dock pinout. If it isn't then something strange is going on.
    Definitely stick with the original cable.
    While it is always good to be careful it is likely not really necessary if your cable is relatively new. I have a mix of cables from by 3G, 3GS, iP4, iPad, and various 3rd party cables. All work interchangeably.

  • Third party lightning cable sold on apple online store not supported

    Since I upgraded my iphone 5s to ios 8.1.1, my belkin lighning cable became an unsupported accessory
    however with my ipad air still sticking with ios 8.0.2, the cable seems fine
    been trying to contact with apple online service but they just won't stop telling me to restore my iphone.
    did anyone come across this problem with any third party "MADE FOR IPHONE" certified lightning cables?

    If Apple Support tell you to restore ,why do you think you know better ???
    Restoring will likely resolve a corruption of the iOS as I expect you have used over the air to update previously
    However if you know better ....................go forth

  • Why don't third party lightning cables work? Apples are too short

    Why since updating my iPhone 5 to IOS7 do none of my lightning cables work. I dismissed the message that came up and had it on charge over night but nothing. This is ridiculous, how can Apple do this to their customers, if they actually made longer charging cables and at a reasonable price people wouldn't have to buy thrid party party. I don't think my Apple cable is even working either.

    If the third-party cable is MFi (Made for iPhone) approved, it should work.
    Apple now sells longer cables.
    <http://store.apple.com/us/product/MD819ZM/A/lightning-to-usb-cable-2-m>
    Belkin has an even longer one.
    <http://store.apple.com/us/product/HB560ZM/A/belkin-21-amp-lightning-to-usb-charg esync-cable>
    It's being sold by Apple, so is probably MFI approved.  Its Lightning connector may not fit some caews, though.

  • Third party application is disrupting my ios operating system for my ipad 2 . i believe it's a virus or malware.

    third party application i mistakenly downloaded is disrupting my ios operating system . It is asking me for the serial number to my ipad 2 and to call a 800 number . What should i do ? My Ipad is messaging me to do this to solve the issue. I think it's some kind of virus or malware.

    It's a Safari phishing scam. Just ignore it. Don't click on any links or call any telephone numbers. Quit Safari.

  • Third party routers that need no firmware update

    What are the best third party WiFi routers with LAN ethernet ports that need no firmware update to work with 10.4.8 and Windows XP?

    Actually the extra ethernet ports is paramount.
    Otherwise you don't know who is being secure to
    whom. You end up having two routers to setup for
    configuration of security. Simplicity is
    important, since I want to be able to help set it up
    for the friend, and forget it.
    ?? That doesn't make any sense - I think you're missing something fundemental here. The extra ethernet ports are on the LAN side of the secure connection. The firewall in the router isolates the internal, LAN network (wireless + ethernet) from the external WAN (aka the big bad internet). Whether or not you have a switch attached to one of the LAN ports makes no difference, security-wise - you are in control of the devices connected to the LAN side of the router. WEP/WPA/WPA2 security controls who is able to connect to the wireless LAN.
    From a security standpoint, there is ABSOLUTELY no difference between buying a router with eight lan ports and buying a router with four lan ports plus plugging in a five-port switch to one of the lan ports. It's exactly the same thing.
    What you don't control is the WAN side of things - the internet itself. You certainly wouldn't want to connect the switch to the WAN port on the router, at least not unless you wanted to run, say, a web server that is exposed to the internet itself. This wouldn't be a good idea in any case - there are better ways to set this up as well (either by setting up a DMZ, or by setting up port forwards)
    There is absolutely no reason why you would want or need two routers for this setup - this is only an issue for extremely large networks.
    The WRT54G has 1 WAN port and four LAN ports. You can have four hardwired devices (computers, printers, switches, etc) on these LAN ports - they are protected from the internet by the firewall in the router. You can also have any number of wireless devices on this same router; these, as well, are on the LAN side of the router, and are therefore protected.
    Adding a switch to the LAN side of the router has absolutely no impact on security. No additional routers would be required.

  • Third party USB products and the Airport Extreme

    If I hook up a USB splitter to my Western Digital hard drive, then plug one USB into my Airport extreme and the other in my XBOX 360 will my files on my hard drive become available wirelessly for use on my computer and also be available to be retrieved wired to my 360?

    You do not want to do that. You can't connect two computers (the Xbox and AEBS) to the same USB bus. Not only won't it work but you may damage one or both (the Xbox and AEBS).

  • Charging 60GB 5G iPod with third party USB chargers

    I have a 60GB 5G iPod which charges fine from my PC and an old wall charger that came with my original 1G iPod. However, it will not charge from either a USB wall charger (Swisstravel) or a 12V car USB charger - both of which charge other USB devices (including other iPods...) fine.
    Has anyone else had this problem? Any solution?
    Thanks
    Nick
    60GB 5G iPod   Windows XP  

    This has been happening to me over this month and I eventually ended up buying a new wall charger. I think that the chargers wear down after so much use.
    kEat0n

  • How do I control the motors in a third party usb toy with LabVIEW?

    Any suggestions?

    Hi, if you are only wanting to control motors than you have a lot of options. Use the parallel port with a current driver, use the serial port and a micro to control the motor. If you want to interface the USB device than this is where to get started.
    http://digital.ni.com/public.nsf/allkb/42B604435E3F9604862565E20043CD30
    http://zone.ni.com/devzone/cda/tut/p/id/4478
    LabVIEW 8.2,8.6,2009...still learning

  • Third Party USB Charger

    The manual inevitably says "Use only Apple's own charger" but gives no specifications as to output voltage, etc.
    I have a perfectly good plug-in USB charger (for an HP PocketPC), which outputs 5.5VDC-1.0A. Any reason this shouldn't be safe/effective?
    TIA
    Nick

    my apple usb charger does not work on the new nano - just like all the speaker kits i have - it won't recharge using them

Maybe you are looking for

  • How to create xml file through SDK?

    Hi, I need help in creating the xml file using SAP B1 SDK? i want to create xml file which is in tally xml format. Warm Ragards, Mahendra

  • Organize scanned pictures without a certain date

    I already read a similar thread, which I couldn't post in, as it was archived. Since iPhoto is designed for digital pictures, we all assume to create and manage our libraries by using digitally taken pictures. I am somehow enough "young" to have the

  • How do you convert win mail.dat files back to MS office files?

    Microsoft files (e.g. excel) when forwarded as attachments and received by MacBook Winmail, get converted to winmail.dat files.  However, MS Office products cannot open these winmail.dat files.  Does anyone have a solution for this "bug"?

  • Configuration related PP order closing.

    Hello all SAP Controlling Expert, I would like to know, is there some configuration of CO module that related to PP order completion status process? Such as  if PP order status is ...... CO Process can be continued or can not continued. Thanks in adv

  • Interactive Adobe Form's  Language Translation

    Hi all, we activated the MSS 60.1 version on the SAP NetWeaver 2004 Enterprise Portal. We need to activate a link on EP that refers to PCR application. From this link we want to call all the Interactive Adobe Forms associated to the ISR standard scen