Time capsule is slow and inconsistent

It seems that the wifi is much slower than my old airport extreme, and inconsistent in terms of connectibility and strength. Any hints? I've been at this for two days.

All,
Maybe trying some of these suggestions will help?
*_Slow Time Capsule Transfer Speeds_*
*Initial Backup Best Over Ethernet*
It is recommended that you perform the initial full backup via ethernet, then all subsequent backups via wireless.
*Transmit Power & Wide Channels*
If you are using the 802.11n only (5 GHz) radio mode, you can also select to use wide channels, which provide higher data throughput in your network.
Launch Airport Utility
Select your Time Capsule on the left.
Click “Manual Setup”.
Select “Airport” in the toolbar.
Click the “Wireless” tab.
Click “Wireless Options...” at the bottom of the window.
Adjust the “Transmit Power” to 100%.
Put a check mark in the box labeled “Use Wide Channels”.
Click “Done”.
Click “Update” in the lower right hand corner.
Wait for the Time Capsule to restart and then see if your network speeds improve.
*Anti-Virus Software*
Are you running anti-virus software. Disable it and see if network speeds improve. The discussion boards are filled with users who are experiencing degraded network speeds due to their anti-virus software.
One poster observed: “I had the exact same problem 5mins ago, it had taken 2 hours to back up 2GB, I realized I installed Sophos anti virus a couple of days ago. When I turned that off my back up is speeding through.”
Another contributor stated, “I am doing the first backup to my time capsule, about 71 Gb, It seems to be going about 1 Gb per hour. is this seem OK? I tried the ethernet connection and the speed was about the same. It has been going all night and after 12 hours it is at only 12 Gb of 71….I found the problem, I uninstalled Norton and the problem went away. It backed up in about 3 or 4 hours”
*Wireless Security Issue*
Some who have experienced degraded network speeds have isolated the problem to their wireless security setup. Try this:
Launch Airport Utility
Select your Time Capsule on the left.
Click “Manual Setup”.
Select “Airport” in the toolbar.
Click the “Wireless” tab.
Change “Wireless Security” to “None”.
Click “Update” in the lower right hand corner.
Wait for the Time Capsule to restart and then see if your network speeds improve.
Granted, this is far from desirable. But it does help to isolate the problem in you instance. Maybe simply resetting the security with a new password will help?
Let us know if any of these procedures helped.
Cheers!

Similar Messages

  • Time Capsule is Slower and has a Weaker Signal than Airport Express

    I have been using an airport express (g) without any problems for several years and usually get full signal strength throughout my small manhattan apartment. I recently decided to upgrade to a Time Capsule. I set it up and found that signal was weak and data transfer was slow. After rebooting it and installing the firmware update, things did not get any better. I took my laptop and TC to the Apple Store and they set it up again for me. In the Apple store, I found that the connection was strong and that the data was extremely fast. When I brought the unit back, I was only able to connect with a few bars (4) and found the data transfers to be extremely slow, practically unusable. I'm not sure what to do, I think there's something interfering with the signal but then again, I put the TC right where the old AirPort Express used to deliver a strong (full) signal.
    Any suggestions?

    I set the Time Capsule to channel 11 from automatic. Since then, the Time Capsule has been working perfectly. I love it.

  • Time capsule running slow and backing up whole disc each time

    I am on a Powerbook running Mac 0SX 10.6.8.
    My time capsule back ups now take hours and appear to be backing up hundreds of files and many GBts each time, even if I run it straight after a previous back up with no file changes made.
    Does anyone have any suggestions of anything I can try?
    Thanks
    Tom

    Load the widget to get actual log info from the TM.
    A1 http://pondini.org/TM/Troubleshooting.html
    Also do a verify disk.. both the computer hard disk.. and the TC sparsebundle.. See A4.

  • Time Capsule - Very slow and eventually unresponsive over wi-fi.

    Hi,
    I've been using my TC for some time now, but it was the first time I had to recover a file. I know it's slow as **** to backup over wi-fi and that it takes aaages to "prepare" the backup. Also I did the initial backup using a cable and not wi-fi.
    My question is: Why is it SO slow to browse and restore small files from a not-so-far-away backup, like, from yesterday? First, when I tried to browse the previous versions of the file it took aaaages to show the contents of the folder and eventually crashed while I stared incredulous the screen...
    Then when I tried again it took it a very long time to browse the folder (I went for a coffee...) and then another 5 minutes to restore a very small file.
    I know it's not supposed to be blinking fast, but it's borderline unusable. Isn't it supposed to be at least "not annoying"?

    Experiencing the same problem. Drag/Dropping a 30Mb file from my HD to TC takes about a minute. Tried about all suggestions and didn't see an improvement. TC is in 5GHZ n mode with only my iMac as a client. Speeds should be around 9 Mb/s instead of the 0.5 Mb/s I'm observing. I've switched off Spotlight indexing for TC, de-activated the Airport status indicator, did several hard resets of TC and put ACK at zero instead of the default value of 3. No major impact; my 30Mb file continues to be transferred in around 60 seconds from iMac to TC. I read one comment that TC might be sensitive to heat, so my next trial-and-error initiative will be to put TC in a cooler spot to see if this has an effect. I'm very eager to learn how to get TC up to 9 Mb/s and hope Apple will pick up on this discussion. I assume they're very aware of the issue as there's quite some discussion going on on this topic. One thing I also tried was downgrading TC firmware to a more stable version, where Airport Extreme v5.5 was advised. I didn't succeed, assuming this old version is not compatible with my Intel Mac. I would like to know if there's a stable robust throughput firmware version available for TC I could downgrade to...??

  • Time capsule painfully slow wifi

    New time capsule , painfully slow wifi , cisco works lightning fast so the issue is with the TC. Looked at forums and I see it's a common isssue. Any ideas that actually work?

    Download the free  iStumbler  app to examine the strength of your connection.
    If it's not good, look for interference with another wireless device, cordless phone, microwave oven, etc.  Turn them off temporarily;  if you find an offender, move it farther away.  See  AirPort and Bluetooth: Potential sources of wireless interference  for more.
    Try different WIFI channels.

  • My time capsule is full and when I attempt to back up, I only receive a preparing back up message and the earliest and most recent back up dates remain the same.  Why are the oldest backups not being deleted to make room for the newest backups?

    My time capsule is full and when I attempt to back up, I only receive a preparing back up message and the earliest and most recent back up dates remain the same.  Why are the oldest backups not being deleted to make room for the newest backups?

    linda mariefromharper woods wrote:
    My time capsule is full and when I attempt to back up, I only receive a preparing back up message and the earliest and most recent back up dates remain the same.  Why are the oldest backups not being deleted to make room for the newest backups?
    It may be in the process of making room.  What version of OSX are you on?    (That process can be excruciatingly slow on Leopard or Snow Leopard backups over a network;  Lion has improved it greatly.)
    A clue may be lurking in your logs.  Use the widget in #A1 of  Time Machine - Troubleshooting to display the backup messages from your logs.   That should help you figure out what's going on.  If in doubt, copy and post them here (but if the same ones repeat over and over, drop most of the duplicates).
    If you can, connect via Ethernet; it will be 2-3 times faster.

  • Setup a wired network  between Time Capsule, Airport Extreme and Express

    I currently have a Time Capsule, Airport Extreme N and an Airport Express N. They are currently connected wirelessly via the "extend network" mode. So I do have wireless connection throughout my home but I notice that it is slow especially compared to gigabit Ethernet. I now like to do the same but then connect the three devices over Ethernet as I have on each floor also Ethernet connections available that are connected via a wired switch.
    How can I configure the three devices in such a way that they use the gigabit Ethernet wired connections as their "backbone" and then give wireless access to each floor as if it is one wireless network, and where I can connect other wired gigabit devices via the time capsule and airport extreme Ethernet ports?
    I have one Internet connection that comes via Ethernet from my cable modem. This is now connected to my time capsule who creates the internal network and assigns internal IP addresses.
    Can anybody advise how to configure each device? And to which ethernet port I should Airport Extreme?
    Thanks
    Alexander

    Welcome to the discussion area, Alexander!
    +How can I configure the three devices in such a way that they use the gigabit Ethernet wired connections as their "backbone" and then give wireless access to each floor as if it is one wireless network, and where I can connect other wired gigabit devices via the time capsule and airport extreme Ethernet ports?+
    You will be setting up what is known as a "roaming" network using the etherent backbone for your network. This will produce the best possible bandwidth on your network for both ethernet and wireless connections.
    _On the Time Capsule_
    Open AirPort Utility - Click Manual Setup
    Click the Wireless tab below the row of icons
    Remove the check mark next to "Allow this network to be extended" (This is only checked if you are extending your network using wireless only and you will be using ethernet to connect your devices, not wireless).
    Update to save changes and the Time Capsule configuration is complete.
    _On the AirPort Extreme_
    Connect an ethernet cable from one of the LAN <-> ports on the Time Capsule to your ethernet switch. Then connect another ethernet connection from the switch to the WAN (circle icon) port on the AirPort Extreme.
    Open AirPort Utility - Click Manual Setup
    Click the Wireless tab below the row of icons
    Wireless Mode = Create a wireless network (Not extend as you might think. Extend is only used if the Time Capsule and AirPort Express are connecting using wireless only)
    Wireless Network Name = Exact same name as your AirPort Extreme wireless network
    Radio Mode = Same setting as your AirPort Extreme
    Channel = Automatic
    Wireless Security = Exact same setting as your AirPort Extreme wireless network
    Wireless Password = Same password as your AirPort Extreme wireless
    Confirm Password
    Click the Internet icon
    Connect Using = Ethernet
    Connection Sharing = Off (Bridge Mode)
    Update to save changes and configuration is complete
    _On the AirPort Express_
    You can connect an ethernet cable from the switch..or..from one of the LAN <-> ports on either the Time Capsule or AirPort Extreme, whichever is easier.
    Set it up exactly the same as the AirPort Extreme above and update to save changes.
    Power off the Time Capsule, AirPort Extreme and AirPort Express for a few moments. Then power up the Time Capsule first and let it run a moment, then power up the AirPort Extreme and then the AirPort Express.
    If you have a laptop running Leopard or Snow Leopard, you can move your computer around and check to see which device it is connecting to for wireless. Hold down the option key while you click on the fan shaped AirPort icon at the top of the screen and look for the BSSID. That is the AirPort ID of the device to which you are connected at the time.
    To get the AirPort ID of each of your Apple routers, open AirPort Utility and click on a device on the left. On the right, you'll see the AirPort ID for that device.
    For ethernet connections, you can plug into an available port on the switch, the Time Capsule, or the AirPort Extreme.
    You should be all set. Please post back on your progress.

  • Time Capsule Network SLOWS

    I have a 1 TB Time Capsule (purchased July 08) directly connected via ethernet cable to a broadband cable network; I use the TC for my home wireless network. Speed of download/upload will change over time. I test on www.speakeasy.net/speedtest and find that download speed will start around 10 mbps, then slow to ~1 mbps over the course of a few days. If I power off the time capsule (unplug it) wait a few seconds; power back on (plug back in), the upload speed returns to ~10 mbps. Upload speed does not change as drastically.
    Any thoughts, ideas as to what's happening? How to handle? This doesn't seem like something I should have to routinely do (power on/off the TC).
    Thanks.

    *_Time Capsule Weak Signal Strength / Dropped Connections_*
    Forgive the size of the post, but the suggestions below have helped others with similar issues. Try each topic individually and see if things improve, If not move on to the next one.
    *Keep the Time Capsule Cool*
    Some posters have observed that when they positioned the Time Capsule for better ventilation and cooling, their network connectivity issues resolved themselves. Also avoid locating the devise within poorly ventilated cabinets or piling items around or on top of it.
    *Time Capsule Orientation*
    While the location you chose to setup your Time Capsule may be acceptable, but the direction it is oriented can have an effect on signal strength. It appears that the signal of the Time Capsule does not radiate equally from all sides of the devise.
    The antennas within the devise are positioned along the 3 smooth sides. That is, there is no antenna on the side bearing the ports and cables. As a result, position the devise with the ports and cables AWAY from the direction of most of the clients that will be connecting to it.
    *Cordless Phones*
    Some users have discovered that the cordless phones they have in the home occupy or are near the same bandwidth as their wireless network (2.4Ghz or 5Ghz). Try temporarily disabling the handsets and their bases and see if network connectivity improves. If so you may need to change the channel that the phone uses or purchase phones that occupy a different bandwidth.
    *Proximity To Other Devices*
    One poster observed: “Finally have full access, full speed, and full functionality. Initially I installed the Time Capsule at the location of my cable, cable modem... which of course was next to my HDTV, DVD, Apple TV, Amplifier, etc. Get the picture? After about 4 weeks of starts and stops, resets and repeated initial backups, I moved the unit to another location, closer to my Mac, and in an area where there are no other electronics. Now, it runs perfect.” [http://discussions.apple.com/thread.jspa?threadID=1734818&tstart=0]
    *Change Firewall Settings* #
    Go to System Preferences --> Security.
    Click the Firewall tab.
    Change setting to “Set access for specific services and applications”.
    The System will now ask you when each process wants to penetrate the firewall. Once you click “Allow” each time you are asked, it will be saved in the pane at the bottom of this window and it should never ask you again.
    One poster observed, “Since I made this change, my wireless has been strong and Time Machine works like a champ and the impact on my network performance is minimal. I speculate that the change in performance is due to security protocols or services that run in the 'allow all incoming connections' and 'allow only essential services' modes. Whatever the reason this fix has worked for me for over 2 months without resetting my airport connection or time capsule.” [http://discussions.apple.com/thread.jspa?messageID=8348496#8348496]
    *Change Time Capsules’ Channel*
    Launch Airport Utility.
    Select the device on the left.
    Click "Manual Setup."
    Select “Airport” in the toolbar.
    Click the "Wireless" tab.
    If “Channel” is set to “Automatic” try changing to a different one. Holding the Option key down and clicking the drop-down menu should provide more channels to choose from. If you have another wireless router operating, ensure that each devices’ channels are as far apart as possible.
    Click “Update”.
    Close Airport Utility.
    *Preferred Networks & Airport Services*
    You may be experiencing interference from other networks in your neighborhood. When you click the Airport menu are there other networks listed other than your own?
    If so, is your network at the top of the list? It should be.
    Go to System Preferences --> Network --> Select Airport on the left.
    Click "Advanced". In the “Airport” tab note the various local wireless networks that Airport detects. Is the network you prefer to connect to at the top of the list? If not drag it to the top. Are there other networks you never intend to connect to (an old work network, or a neighbors network)? Then highlight them and click the "-" button.
    Make sure “Remember any network this computer has joined” is checked.
    Click "OK".
    For "Network Name" be sure your network is selected and then click "Apply".
    Is Airport (wireless) your primary means of connecting to your network? If so, is Airport at the top of the list of services on the left? It should be.
    Click the small “Gear” button at the bottom of the window and select “Set Service Order”.
    Now drag Airport to the top of the list.
    Click “OK”. Click “Apply”.
    Now see if network connectivity has improved.
    *Transmit Power & Wide Channels*
    If you are using the 802.11n only (5GHz) radio mode, you can also select to use wide channels, which provide higher data throughput in your network.
    Launch Airport Utility
    Select your Time Capsule on the left.
    Click “Manual Setup”.
    Select “Airport” in the toolbar.
    Click the “Wireless” tab.
    Click “Wireless Options...” at the bottom of the window.
    Adjust the “Transmit Power” to 100%.
    Put a check mark in the box labeled “Use Wide Channels”. (If you are using a 802.11a/b/g (2.4GHz) radio mode then select “Interference Robustness”)
    Click “Done”.
    Click “Update” in the lower right hand corner.
    Wait for the Time Capsule to restart and then see if your network speeds improve.
    *Faulty Airport Card*
    One poster reported: “I reckoned the fault must be with the Macbook’s hardware so took the plunge and got a new airport card fitted to my Macbook and now everything is working fine. At last I have a working Macbook!” [http://discussions.apple.com/thread.jspa?threadID=1719326&tstart=0]
    If you think this might be the case, follow the steps outlined in this KB article to determine if your Airport card is still being detected by your system:
    [http://support.apple.com/kb/HT2601]
    Let us know if any of the above helped improve your situation.

  • I just did an Time Capsule firmware update and now my Time Capsule is dead.  What happened?

    I just did a Time Capsule firmware update and now my Time Capsule is dead.  What happened?

    tresbaileys wrote:
    it may be important to note that when I put my ear to the box I can still hear the HD spinning (although no lights are lit and it doesn't show in the airport utility).  Ideas??
    That is very bad.. how old is it??
    The Gen4 TC can die this way.. it is not usual but it happens.
    Leave it for several hours to cool off. Do a factory reset immediately when you try to restart it.
    The Factory Reset.
    Power down the TC.
    Hold in reset. and keep holding it in. Be Gentle! It is a tiny surface mount switch with a plastic lever.. Attempting to push it out the other side of the TC will not make the switch turn on better.
    (I fix TC and have several reset levers bent over and jammed or broken off).
    Power on the TC.. remember with the reset held in.. this needs three arms.. a friend or power switch you can get to with your feet..
    Keep holding in reset for about 10sec until the front LED flashes rapidly.
    Release reset and wait .. the boot will be slow as it deletes previous setting.. only from router side and pulls out the factory defaults. No files are deleted on the hard disk.. but the name of the TC may change.
    Tell me exactly what the LEDs do throughout this process.
    Both the main one at the front and the LED on the ethernet ports which should all flash during bootup.
    If it is less than a year.. of course Apple will replace under warranty.. 2 years in some places.. Europe .. places with stronger consumer laws. If you have applecare on a computer it should still cover the TC.
    I kind of doubt you are going to get this going again... but we can try.

  • How to setup apple time capsule with FIOSinternet and VZ router?)

    Hello,
    I have Apple time capsule and the VZ Router MI424WR. I current set up:
    1. VZ router - wireless off, the rest is standard
    2. Time capsule: Wireless on in Bridge mode
    Result: Internet works but the wireless network is very in-stable. Airtunes is nearly not usable.
    I searched in the Internet and there was several comments that is is not a good combination. Therefore it is recommended to convert the VZ router in a modem mode and use only the Time capsule as the router. I tried this several times I do not get it to work. I followed this procedure (http://data.agaric.com/node/2160) but then I need the PPPoE Account number and password. But there do I get this? The Verizon support was not really helpful.
    Please, is there a good and complete description to solve that issue?
    Thanks in advance
    Moebius

    Go back to your first setup ...
    Verizon router with wireless turned off
    Apple Time Casule with wireless turned on
    Method 1:
    With the Time Capsule in "Bridge Mode", if I remember correctly, you should connect the WAN port to one of the open ports on the Verizon router (I believe bridge mode also turns off the DHCP server on the Time Capsule, if not, find that and turn if off as well).   Change the addressing mode for the Time Capsule to "static" and assign it an address on the LAN which is not in use (choose something you know is out of the way but on the LAN -- I suggest 192.168.1.180 to start -- you can change it once you get everything working).
    If it doesn't work this way for you, move the cable from the WAN port on the Time Capsule to Port 1 and try again.
    Method 2:
    This results in a router behind a router setup, but unless you have devices connected directly to the Verizon router, it shouldn't be a problem.  
    With the Time Capsule disconnected from the Verizon router, turn on "Connection Sharing" (not bridge mode) and make sure DHCP is enabled on the Time Capsule.  You need to change the address range being used by the Time Capsule (which I think defaults to 192.168.1.x to another network -- I suggest, 192.168.2.x with a netmask of 255.255.255.0 and give the router an address of 192.168.2.1 on the LAN side.  Now, connection the WAN port to one of the Verizon router LAN ports.  If you had anything connected to the Verizon LAN ports, move those over to the LAN ports on the Time Capsule and reboot them.
    Method 3:
    This is the least desirable of the scenarios because it relies on Verizon's crappy radio in their router (the Time Capsule has a much better radio and support 802.11n as well as b and g) whereas Verizon's only support b/g.    Go back to the configuration for Method 1, but also turn OFF wireless on the Time Capsule and turn on wireless on the Verizon router.   Try both bridge scenarios described -- using the WAN port first and if that didn't work, then moving the connection to port 1.
    There is no scenario where you can place the Verizon router behind the Time Capsule -- since I believe Verizon is using all MoCA connections for the WAN side of their connection (you'd have to get Verizon to convert you to ethernet WAN and then they would not support you most likely for any STB issues with your FiOS if the Time Capsule was between the ONT and their router ... so don't even bother wasting time there ... more headaches than it would be worth.
    If you're still not sure exactly what each configuration screen on the time capsule should say, post some screen snaps (or the configuration settings/choices which you are unsure about and someone will likely know the answer here).

  • Can I use two Time Capsules? one as an extension of my laptop (for music and video storage) and the other one to back up everything from the laptop and  Time Capsule (for music and videos)

    Can I use two Time Capsules? one as an extension of my laptop (for music and video storage) and the other one to back up everything from the laptop and  Time Capsule (for music and videos)

    Not via Time Machine.   It cannot back up from a network location.
    The 3rd-party apps CarbonCopyCloner and ChronoSync may be workable alternatives.
    EDIT:  And, if you're going to do that, you could back up from the Time Capsule to a USB drive connected to the TC's USB port.  Second TC not required.
    Message was edited by: Pondini

  • Time Capsule flashes amber and loses connection at least once a day

    Hello,
    I got my Time Capsule a month ago. I had an old one from 2008 which I gave to a friend, so it was time to upgrade. I have no idea what's going on, but the Time Capsule flashes amber and I lose my Internet connection at least once a day, sometimes two or three times within a few hours.
    Is anyone else experiencing this? Any idea how to fix it?
    If it matters, I'm on a mid-2010 MBP running OS X 10.8.5.
    Thanks!

    You and everyone else.
    https://discussions.apple.com/thread/5140686?tstart=0
    It is not stable firmware.. or has issues .. with some modems.. or is just faulty.. pick one or two choices.
    There is no fix because this is really a bug.

  • Time Capsule: WI-FI and Ethernet at the same time

    Hi everybody,
    I've connected my mac book (Lion) to a 2T time capsule via wifi and it works fine. The TC is connected via wifi to an existing network (and internet connection).
    Unfortunately, using this configuration, ethernet connection between the macbook and the TC (to speed up file copying) doesn't work: it just keeps connecting via wifi.
    I've also tried to switch of the wifi connection on the macbook to "force" the use of the ethernet cable but it doesn't work.
    Is there any way to use the wifi connection but, when needed, just connect the macbook via ethernet without changing the TC configuration?
    Thanks in advance
    M

    When you configure the TC to "join a wireless network" as you have likely done, it performs no routing functions in this type of setup.....and the Ethernet ports are not enabled.
    In effect, the TC becomes a wireless hard drive when it "joins" a wireless network.
    You would need to consider whether you want to reconfigure your TC in a a diffferent way......(connecting it to your main wireless router using a wired Ethernet cable)......if you want to have Ethernet capability on the TC.

  • How to divide time capsule for Mac and PC back up

    Want to know if a cant use my time capsule to do back up for my MacBook and do manual back up for the PC of my wife

    How to divide time capsule for Mac and PC back up
    It is not possible to divide or "partition" the Time Capsule disk......unless you pull the hard drive from the Time Capsule (which voids the warranty), place it in a separate enclosure or caddy, connect the enclosure directly to your Mac, and use Disk Utility to partition the disk. Then, you must reinstall the disk back in the Time Capsule.
    This is a lot of work....best done by an experienced technician. The operation will likely cost more than the cost of the Time Capsule.
    Life would be tons easier if you used the Time Capsule with your MacBook and added a separate USB drive to the PC.
    If you do not need to divide or partition the Time Capsule storage space, and you are willing to have the Mac and PC share the same space, take a look at an application like Macrium Reflect to backup the PC to the Time Capsule disk.
    Still, having done this in the past, things would be much faster and easier for you if you use a separate USB drive for the PC.

  • Dual Band Network: Time Capsule (N only) and Linksys (B/G) Works *Long*

    Ok, so this was more tedious than I thought it would be, but things actually seem to be working at this point.
    Goal: Create a Dual Band network with Time Capsule (N only) and a Linksys WRTSL54GS (B/G)
    Time Capsule: 1000BaseT wired, and 802.11N 5Ghz only wireless
    Linksys: 100BaseT wired, and 802.11G 2.4Ghz wireless
    Airport Utility 5.3.1
    Time Capsule v. 7.3
    I set Time Capsule up first, following the step by step directions for "Create a wireless network"
    802.11N only, 5Ghz
    WPA2 Personal
    DHCP 192.168.1.1 (kinda important)
    This worked fine-tested on a C2D iMac, both thru ethernet and wirelessly thru N. Time Machine backed up fine.
    Now the tricky part, configuring the Linksys.( I just want to mention I had to reset this thing completely about 10 times to get it to work, using a miniscrewdriver)
    Starting with a freshly reset Linksys, I connected from my MacBook ethernet port to one of the Linksys ethernet ports (Not the WAN)
    I disabled Airport
    I logged in to 192.168.1.1 using blank for login, admin for password (default for Linksys)
    I did the following:
    1) Confirmed Internet Connection Type was "Automatic Configuration-DHCP"
    2) Changed Network Setup to "DHCP Server-DISABLED"
    3) Turned off the Firewall settings in Security (not sure if this is necessary)
    4) Changed the Operating Mode from "GATEWAY" to "ROUTER"
    5)Changed the SSID to "LinksysG_ONLY" or something like that
    After each one of these steps, I had to save the configuration, thru the Linksys browser interface-which blows.
    6) Finally, I changed the Local IP Address of the Linksys from 192.168.1.1 to 10.0.1.251 (thanks to Henry B. for that)
    7) And....I no longer had access to the Linksys at all! This stumped me for a while, until...
    8) I checked my Ethernet settings (in System Preferences/Network): 192.168.1.1 was set as default router address. But my Router (at least for configuration purposes) was now 10.0.1.251, so it could no longer find it.
    9) So I added a new Ethernet port (using the "+" sign), called it Ethernet-Linksys. Set it to Manual. Put in an IP of 10.0.1.250, and a Router IP of 10.0.1.251.
    10) I got access to the Linksys setup page again! (Note: I'm sure there is an easier way to do this, but this is how I got mine to work )
    11) I set up WPA security again, set it to an unused channel (2 in my case), mixed b/g network.
    12) Finally, I moved the ethernet cable from my MacBook directly to one of the ethernet ports on the Time Capsule. I did NOT hook up the other end to the WAN on the Linksys (which for some reason I had done 100 times before) I left it in one of the 4 ethernet ports on the Linksys. Repeat, the WAN (ethernet) port remains empty.
    13) I then turned Airport back on the MacBook, connected to "LinksysG_ONLY", and...I was online. And everything seems to work.

    Hi kjk et al,
    I've been searching the boards for something like what you have described in such nice detail. Before Time Capsule, I used a Netgear g router connected to the cable modem and an older Apple base station connected to the Netgear as a bridge. I removed the Netgear and set up my Time Capsule as the primary. The newer computers in my network can access the Time Capsule, but the old Dell with a 802.11g wireless card cannot. I don't remember seeing where I could access TC to change a setting of "N only" or b/g, but I am guessing that it is running N.
    I tried to follow the steps you used for Linksys. The pre-step 1 thing, resetting it "10 times to get it to work" - how do you know when it is really reset? With Netgear plugged into electricity, I stuck a paper clip into the hole labeled on the diagram as "restore factory settings" and watched the color of the IO icon change from green to amber to green. I did it again for good measure.
    I plugged ethernet from PowerBook G4 into Netgear not-WAN ethernet ports (like your MacBook to Linksys). I disabled Airport. Using Safari, I logged into 192.168.0.1 and got to the Netgear SmartWizard configuration assistant. It says, "No Internet Connection Detected. Please check the connections to the Internet WAN port and cable/DSL modem" - so I looked at your instructions but see no mention of connecting the router to the modem.
    Trying to follow your numbered steps...
    1. In SysPrefs: Network, Location showed Automatic, Configure showed Using DHCP.
    2. I don't see an option in Network to "DHCP Server-DISABLED", but I can choose Configure: OFF. I clicked Apply but browser still gives same message.
    I don't know how to continue the steps.

Maybe you are looking for