Title 3d (upwards) goes too fast
I have a title of 23 words in 13 lines of text with an additional 2 lines of spaces after the heading. It goes up the screen too quickly to allow viewers to read it comfortably. I have increased the leading which helps but not enough.
How can I slow it down please? I can't see any parameters to adjust.
(BTW, for reasons too tedious to describe, I am using FCE3 — not 4 as stated in my sig. but if FCE4 has a suitable additional control I could use that if necessary.)
Regardless of which text generator you use, increasing the duration of the clip will slow down the scroll. If it's going too fast and the duration is 10 seconds, try 20 or 30 seconds ... whatever works for the amount of text you have.
Of course, if you are using Title 3D for this (which is kinda weird since Title Crawl was made for this), you'll have to move your ending keyframe out to the end of the clip's new duration.
-DH
Similar Messages
-
Audiobook on my itouch is going too fast.
I just download an audiobook on itunes store and put in my itouch with no problems at all.
But when I play the audiobook (on the itouch), the narrator speaks too fast. And the audiobook is forwarding.. I mean it's going 2 sec per 1 sec..
0:01 to 0:03 to 0:05 to 0:07 and so on...
But when I play the audiobook on my pc with itunes, it's neither fast nor slow, it's just normal.
Someone can help because I want to heard the audiobook with my itouch.
I have the 2nd generation Itouch and the audiobook is Run for Your Life (Unabridged) which last 6 hours 26 mins.under the ipod's general "Settings" click on "Music" and make sure Audiobook Speed is set to "Normal"
-
My WLAN chokes when going too fast (Intel 3945 w/ Netgear) [SOLVED]
I recently upgraded my Internet connection from 8/1 to 24/10 and since then I have been able to download at the highest speed without any problems, except for this one of course.
When I'm torrenting and getting higher than 2 MB/s (yes, megabytes) speeds, the connection suddenly "chokes" and puts some sort of threshold on itself at about 150 KB/s. The threshold is not put only on the torrents, but on my entire connection to *this* computer. All of the other computers connected to the router still work fine. This problem doesn't go away unless I reconnect myself to my router. This happens only on Linux, not on Windows as far as I can tell.
What can be the problem? I have Intel 3945 drivers and 2.6.31.
Last edited by skorpan (2009-11-30 21:39:20)This is *EXACTLY* what has been happening to me; thought I was going crazy. I also have an intel iwl3945 and 2.6.31. My router is a netgear wgr614v6. When I associate from *this* computer, after a seemingly random period of time, my connection gets chocked from the normal ~1.5 mb/s to 113 kb/s. This only happens to this computer, however, it *doesn't* happen over the local network, just to the internet. I can only use my full bandwidth after re-associating with the router. I was thinking it had to be a bug in the router firmware, but this looks like too much of a coincidence now...
what router do you use? -
On a PC
I upgraded from CS5 to CS6 (cloud) over the long weekend and I'm now faced with a massive headache. The process actions I use intensively for my work are all foxed by the simple problem that the action playback is going too fast for scripting over two documents to keep up. I have tried everything I can think of but the only thing that allows the action to progress sensibly (as in previous versions of the software) is the step-by-step playback mode. This is too slow to use on an ongoing basis.
The problem is caused by the following sequence
Save as document (on desktop)
Open as document - open as Camera Raw - after settings open in Photoshop
Select All
Copy
Close - saving no
(PS automatically selects previous document)
++++ paste ++++ ERROR Paste command is not currently available
This is where Photoshop should select the previous/underlying document before applying the Paste command. Since the upgrade its been trying to paste the clipboard in the split second after closing and selecting the previous document, and reporting no document available at all. Slowing or pausing the playback with step by step or stop&continue works around the problem but causes workflow to slow down drastically.
Is there a way to script a pause during this one crucial moment? Or is there a preference setting I have overlooked that is casing the behaviour?Save as - open as camera raw - select all- copy - close - paste. The dance is the ony way I can apply Camera Raw settings such as clarity, noise reduction etc to my retouch after the initial raw conversion. Its a well used technique that I've known about for years. Loads of people use this method in CS6, but for some reason I can'y get it to work after the upgrade.
The action is recorded in the regular record/play type action script. Its a big action and would take many hours to convert into javascript (even if I had the skills). I could possibly use the script recorder plugin but that rules out future tweaks without rewriting everything from scratch. app.refresh and $.sleep sound interesting though... is it possible to incorporate them into the basic action script? -
Tooltip with img title disppears too fast
The problem was already described - in 2008. Not sure if it was fixed later, but I got hit by it now.
When I go to (for example) http://xkcd.com/, and hover over image, there is tooltip shown with title attribute of the image.
The problem is that the tooltip disappears after around 2-3 seconds - way too fast to allow me to read it.
Is there any option to make tooltips stay in place until I move the mouse, or press something?
I'm using Firefox 34 on 64 bit Linux (kubuntu).Are you using a possibly special branded Firefox version from the Ubuntu repositories or the official Firefox release from the Mozilla server?
You can find the full version of the current Firefox 34.0 release in all languages and for all Operating Systems here:
*https://www.mozilla.org/en-US/firefox/all/
Create a new profile as a test to check if your current profile is causing the problem.
See "Creating a profile":
*https://support.mozilla.org/kb/profile-manager-create-and-remove-firefox-profiles
*http://kb.mozillazine.org/Standard_diagnostic_-_Firefox#Profile_issues
If the new profile works then you can transfer files from a previously used profile to the new profile, but be cautious not to copy corrupted files to avoid carrying over problems.
*http://kb.mozillazine.org/Transferring_data_to_a_new_profile_-_Firefox -
after ios7 update my iphone 4 is like android os dead slow processing , too fast battery drain,calling process is too low where is apple brand going my friends 11 members using iphone all are got this problem one thing apple have unique and unique fans like me why they spoil their name like this update iam too disappointed iam not say for oppose apple iam say for feedback to grow apple in world because i love apple more please solve it
by real customers
iPhone 4, iOS 7, iam apple suporterplease help me after ios7 update my phone is tooo slowww i want my old iphone
-
Battery capacity going down way too fast
So problem is that my mbp 13" is about 2 weeks old and battery capacity seems to going down too fast. I only have 2 cycles and I did calibration 4 days ago. When I bought it, it was like 5770 or smth and now it's 5500. Think it's normal or maybe it's just wrong info there?
Battery Information:
Model Information:
Serial Number: W004858Q9D3LA
Manufacturer: SMP
Device name: bq20z451
Pack Lot Code: 0000
PCB Lot Code: 0000
Firmware Version: 0201
Hardware Revision: 000a
Cell Revision: 0165
Charge Information:
Charge remaining (mAh): 5431
Fully charged: Yes
Charging: No
Full charge capacity (mAh): 5505
Health Information:
Cycle count: 2
Condition: Normal
Battery Installed: Yes
Amperage (mA): -589
Voltage (mV): 12339It's fine. Cycle to cycle fluctuations of 300-500 mAh are normal.
-
Can't burn disc via iTunes. Burn speed too fast. AGAIN!
"iTunes can't burn this CD because the burn speed is too fast for your CD burner or media. Choose a lower speed in the burning pane of iTunes Preferences then try burning again".
I have been having on going problems burning CD’s in iTunes for YEARS, and I know I am not the only one. I get the error message above. Having checked the forum at the time, and posted for help, I am know there is no real solution except to change brand of disc.
Thing is, now I can’t get ANY brands to work. I’ve been through Verbatim, Maxell, JVC, Sony, but none work. The only brand that would work were TDK audios which I can no longer find anywhere.
I know its not the burner, as Toast works fine, and I know I am not alone. Anyone got any ideas?
Even after years Apple seem to be blanking this question. It’s very frustrating not being able to burn my purchased itunes downloads to disc.To anyone who is interested I think I may have found a possible solution. When you put a blank disc in the drive, wait about 30-60 seconds or so for it to stop spinning before burning.
This seems to work. It's a bit sticky but eventually works. I tried both TDK & Maxwell discs and 9 out of 11 worked. Absolutely no reason why the other 2 didn't, but it's a lot better than none. -
CD burner error: Burn Speed Too Fast
Whenever I try to burn a CD on my eMac an error message says
"iTunes can't burn this CD because the burn speed is too fast for your CD burner or media. Choose a lower speed in the burning pane of iTunes Preferences then try burning again".
It even says that when the burning speed is on x1. It says that on every speed. So does anyone know how I can fix this problem and make it be able to burn CDs? Is it because I have nearly 10,000 songs on my iTunes, so that is somehow making it slow down?
The blank disc I'm using is "High Quality Pure Silver CD-R 80 Tevion"
It has 700 megabytes (80 minutes) on it, and I want to burn a CD that is 60 minutes, exactly. So, help? Thanks.Let me see if I can help you understand your delima.
Just because you buy a very expensive Media Brand, doesn't mean it is any good. There is such a wide range of quality in CD's and DVD's it is really hard to select what is considered to be the best.
A very good guide to use for Media in general for both CD, and DVD's is below.
http://www.digitalfaq.com/media/dvdmedia.htm
Next there are a couple of KEY points to remember when burning, these will help you.
Never have any other Applications open when burning.
I tend to use either CD-R or DVD-R Media, the reason is these 2 formats are the most widely used and recognized in all Players, and Computers alike.
Always choose the slowest speed to get a high quality burn.
This next suggestion is probably the most important.
Not all CD-R's and DVD-R's are the same
Read the packaging carefully
Many will explain that they will burn at all speeds from 1X upwards
This will help insure that your burner Software will choose the correct speed.
Don -
ITunes CD Burn error (media too fast)??
I upgraded to the latest iTunes version and now Im getting errors when I try to burn a playlist. I havent burned a cd off this computer in a long time, so Im not sure if it's iTunes. However, the error, if I remember correctly,said iTunes is unable to burn the playlist because the requested speed is too fast for the burner or the media.
I tried slowing my burning speed to 8X, but it still gave me the error.
Any suggestions? Is it time for a new drive? If so, what are my options? I have the blue CRT (500mhz) iMac.
ThanksSince my original post, I have been able to burn a cd, but still most of the time get the error. Why would it work sometimes, and not other times?
Im guessing the drive is going. Can it be replaced? Are there upgrades available for the CRT iMacs ? -
Hi there
I've got an iphone 2g, FW 3.1.3 and a very strange issue:
The clock is running too fast. After one day the time on my phone is 1 hour ahead ( 1hour/each day). When i connect and sync, the time on my phone jumps back to the normal time, the time on my macbook.
I did a total reset (came from version 3.0), but with no luck.
Ive got no option "Set time automatically" in my Firmware version.
I hope somebody has any idea what's going wrong.
Thank you for reading anyway.
regards
Pedro
Message was edited by: Pedro1982
Message was edited by: Pedro1982Thanx, that helped!!!
Turned out that one of my homes' NLS_LANG had norwegian_norway and the others had american_america. As soon as I changed the norwegian to american, Forms started and I let go a huge sigh of relief :-))
Thanx again! -
My battery seems to be going out fast!!!! HELP!
I just got my black iPod NANO the other day and i charged it before i started to using it, i started downloading my songs and once i took it off the charge it was fine but then a couple min its later and i mean just a couple of min later the battery started going down. I already checked on the apple web site on how to maintain my battey and how to conserve its strength but it really seems that my battery might be bad cuz it just goes down too fast. Put it this way i have to charge it every night. Please help! if any one has any suggestions please let me know...... and if there i a battery that i can buy please let me know as well ! thanks!
thanks for the response. i really appreciate it. how do i go about doing a charge cycle the correct way? i have the usb cable that came with it(so the cpu has to be on). i don't have the actual home charger. so how would i go about doing it corectlly? thanks in advance.
-
T440s UltraNav Touchpad Scroll Too Fast and Jerky
Wife purchased a T440s in November. Arrived December. I installed Windows 8.1 from scratch, and it worked. Then on Friday, Jan 31st 2014, I ran the driver update tool from Lenovo. It upgraded the driver to 17.0.12.60. She noticed that scrolling became much more unreliable. She could sometimes not get docs/webpages to scroll until she clicked around the page. Then she could get scrolling to work again. Also, scrolling speeds increased _dramatically_ to the point it was unusable. Also, the scrolling was quite jerky. So I rolled the driver back to 17.0.12.56 and immediately she noticed a difference. She was able to successfully scroll again and scrolling wasn't too fast and much smoother.
Others have noticed this on Notebook Review's forum. I'm going to ask those people to come here and add their comments.
Can Lenovo please fix the UltraNav driver? Thanks!Yes, I experienced the same problem. Two finger scrolling became unusable (way too fast and erratic) after an upgrade to UltraNav 17.0.12.60. Reverting back to 17.0.12.56 fixed the issue.
Please fix this in the next version. Thank you! -
WHY some HDMP4 1920X1080 import to PAL720X576 jump frame & Moive is not a nomal 25FPS,MOVE TOO FAST?
My PC is WINX64,INTELQUAD Q8200, 8G RAM, PR CS4
THE FILE CODE INFO:
Title/More : SKY02 Digital Camera
Movie name/More : SKY02 Digital Camera
Encoded date : UTC 2008-01-07 00:00:29
Tagged date : UTC 2008-01-07 00:00:29
File creation date : UTC 2010-01-25 12:22:48.500
File last modification date : UTC 2008-01-06 16:00:28.000
Origin : Digital Camera
TAGS : UNG DIGITAL MOVIE
Codec ID : avc1
Codec ID/Url : http://www.apple.com/quicktime/download/standalone.html
Codec : AVC
Codec : AVC
Codec/Family : AVC
Codec/Info : Advanced Video Codec
Codec/Url : http://developers.videolan.org/x264.html
Codec/CC : avc1
Codec profile : [email protected]
Codec settings : 2 Ref Frames
Codec settings, CABAC : No
Codec_Settings_RefFrames : 2
Duration : 26240
Duration : 26s 240ms
Duration : 26s 240ms
Duration : 26s 240ms
Duration : 00:00:26.240
Bit rate mode : VBR
Bit rate : 14186831
Bit rate : 14.2 Mbps
Width : 1920
Width : 1920 pixels
Height : 1080
Height : 1080 pixels
Pixel Aspect Ratio : 1.000
Display aspect ratio : 1.778
Display aspect ratio : 16/9
Frame rate mode : CFR
Frame rate : 50.000
Frame rate : 50.000 fps
FrameCount : 1312
Colorimetry : 4:2:0
Bits/(Pixel*Frame) : 0.137
Stream size : 46532807
Stream size : 44.4 MiB
Stream size : 44 MiB
Stream size : 44 MiB
Stream size : 44.4 MiB
Stream size : 44.38 MiB
Language : eng
Language : English
Encoded date : UTC 2008-01-07 00:00:29
Tagged date : UTC 2008-01-07 00:00:29
Audio
Count : 102
Count of stream of this kind : 1
Kind of stream : Audio
StreamKindID : 0
ID : 2
Format : AAC
Format/Info : Advanced Audio Codec
Format version : Version 4
Format profile : LC
Format settings, SBR : No
Codec : A_AAC/MPEG4/LC
Codec : AAC LC
Codec/Family : AAC
Codec/Info : AAC Low Complexity
Codec/CC : 40
Duration : 26240
Duration : 26s 240ms
Duration : 26s 240ms
Duration : 26s 240ms
Duration : 00:00:26.240
Bit rate mode : VBR
Bit rate : 127258
Bit rate : 127 Kbps
Nominal bit rate : 128000
Nominal bit rate : 128 Kbps
Maximum bit rate : 192000
Maximum bit rate : 192 Kbps
Channel(s) : 2
Channel(s) : 2 channels
Channel positions : L R
Sampling rate : 48000
Sampling rate : 48.0 KHz
SamplingCount : 1259520
Resolution : 16
Resolution : 16 bits
Stream size : 417407
Stream size : 408 KiB
Stream size : 408 KiB
Stream size : 408 KiB
Stream size : 408 KiB
Stream size : 407.6 KiB
Language : eng
Language : English
Encoded date : UTC 2008-01-07 00:00:29
Tagged date : UTC 2008-01-07 00:00:29Why not convert to MS DV AVI type2 before import? Use Google to find a suitable converter.
-
An enemy to follow me around the screen but not too fast
Hi I'm building English teaching apps but through games.
I'd like a BUG enemy to follow me around but NOT TOO fast as I have little kids of 5 years old using this,
Would it be something like get the coordinates of my HERO character and send the BUG there.
I use POINT at the moment to send my HERO to where the mouse clicks.
Could I send the BUG there as well but using less x and y increments.
Would this be too much for the processor - too much going on with music playing as well?again, don't remove it:
var speed:Number=.99;
public function onEnterFrame(event:Event):void {
var xDistance:Number=clickPoint.x-this.hero.x;
var yDistance:Number=clickPoint.y-this.hero.y;
if (Math.abs(xDistance)>10) {
var angle:Number=Math.atan2(yDistance,xDistance);
this.hero.x+=v*Math.cos(angle);
this.hero.y+=v*Math.sin(angle);
} else {
this.hero.gotoAndPlay("static");
enemy1.x = speed*enemy1.x+(1-speed)*hero.x;
enemy1.y = speed*enemy1.y+(1-speed)*hero.y;
if (clickPoint.x>=hero.x) {
this.hero.gotoAndPlay("right");
//trace(Math.abs(xDistance));
if (this.hero.x>=clickPoint.x) {
this.hero.gotoAndPlay("left");
//trace(Math.abs(xDistance));
Maybe you are looking for
-
On my Macbook Pro I had no problem for 3 years using my wireless hp printer, the past few days it couldn't recognize the printer and I, unfortunately, delted the printer thinking I could re-find it and now I cannot find it at all.
-
When i am in Yahoo mail and am opening on an email to open, the email starts to open (I can see the content of the email for a second) and then I get a screen with a message that states 'Whoops! The page could not be found. Try giving it another chan
-
ACS, Access Service and Authorization
I am running ACS 5.2 and I am trying to set up 3 new SSIDs, 2 of which are unsecured and 1 that is secured. I am trying to figure out the best way to authorize them based on which network they are coming from. All the authentication requests are co
-
hi all .. plz tell me how to declare an array in pl/sql editor .. why this help of oracle is not so helping ??? i m using 6i dev with 9i db. thanx
-
Apps wont close since I installed the latest upgrade
Since I installed the latest update for my phone, I cannot close the apps. As usual, I tap the icon, but it doesn't "wiggle", so I cannot close it. Has anyone else come across this problem.