Trouble with international translation

Hello all,
I'm having a problem getting international calls to complete. I have the below in my Cisco 5350 configs with some lines removed to save space. Debug is below that. It appears my translation rule is ok to some extent as the test indicates. What am I overlooking? Any help will be greatly appreciated.
Sprint5350#test voice translation-rule 2 011862196990
Matched with rule 1
Original number: 011862196990   Translated number: 0111862196990
Original number type: none      Translated number type: none
Original number plan: none      Translated number plan: none
voice translation-rule 1
rule 1 /\+1$.*$/ /\1/
voice translation-rule 2
rule 1 /^01/ /011/
voice translation-profile Incoming_Calling_Party_Num
translate calling 1
voice translation-profile outgoing_international
translate calling 2
translate called 2
controller T3 3/0
framing m23
clock source line
cablelength 133
t1 1-7 controller
description Sprint DS3 - 75955030
controller T1 3/0:1
framing esf
pri-group timeslots 1-24 nfas_d primary nfas_int 0 nfas_group 1
controller T1 3/0:2
framing esf
pri-group timeslots 1-24 nfas_d none nfas_int 2 nfas_group 1
controller T1 3/0:3
framing esf
pri-group timeslots 1-24 nfas_d backup nfas_int 1 nfas_group 1
controller T1 3/0:4
framing esf
pri-group timeslots 1-24 nfas_d none nfas_int 3 nfas_group 1
controller T1 3/0:5
framing esf
pri-group timeslots 1-24 nfas_d none nfas_int 4 nfas_group 1
controller T1 3/0:6
framing esf
pri-group timeslots 1-24 nfas_d none nfas_int 5 nfas_group 1
controller T1 3/0:7
framing esf
pri-group timeslots 1-24 nfas_d none nfas_int 6 nfas_group 1
interface Serial3/0:1:23
no ip address
encapsulation hdlc
isdn switch-type primary-4ess
no cdp enable
dial-peer voice 150 pots
translation-profile incoming Calling_Party_Num
translation-profile outgoing outgoing_international
destination-pattern 011.T
translate-outgoing called 1
direct-inward-dial
port 3/0:1:D
forward-digits 0
dial-peer voice 100 voip
preference 1
modem passthrough nse codec g711ulaw redundancy
voice-class codec 1
incoming called-number 800.......
dtmf-relay rtp-nte
fax protocol t38 ls-redundancy 0 hs-redundancy 0 fallback pass-through g711ulaw
no vad
*Sep 4 17:57:57.433: ISDN Se3/0:1:23 Q931: RX <- SERVICE pd = 3 callref = 0x0000
        Change Status i = 0xC0 - in-service
        Channel ID i = 0xE9818398
                Exclusive, Interface 1, Channel 24
*Sep 4 17:57:59.001: //-1/BC10816380D4/RXRULE/regxrule_stack_pop_RegXruleNumInfo: stack=0x6871D9EC; count=1
*Sep 4 17:57:59.001: //-1/BC10816380D4/RXRULE/regxrule_get_profile_from_dialpeer_internal: Error: Invalid input peer_tag=0 direction=incom        ing
*Sep 4 17:57:59.001: //-1/BC10816380D4/RXRULE/regxrule_stack_push_RegXruleNumInfo: stack=0x6871D9EC; count=0
*Sep 4 17:57:59.001: //-1/BC10816380D4/RXRULE/regxrule_stack_push_RegXruleNumInfo: stack=0x6871D9EC; count=1
*Sep 4 17:57:59.001: //-1/BC10816380D4/RXRULE/regxrule_profile_translate_internal: number=5024101498 type=unknown plan=unknown numbertype=        calling
*Sep 4 17:57:59.001: //-1/BC10816380D4/RXRULE/regxrule_match: No match; number=5024101498 rule precedence=1
*Sep 4 17:57:59.001: //-1/BC10816380D4/RXRULE/regxrule_profile_match_internal: No match found
*Sep 4 17:57:59.001: //-1/BC10816380D4/RXRULE/regxrule_profile_translate_internal: No match: number=5024101498 type=unknown plan=unknown
*Sep 4 17:57:59.001: //-1/BC10816380D4/RXRULE/regxrule_profile_translate_internal: number=011862196990 type=unknown plan=unknown numbertyp        e=called
*Sep 4 17:57:59.001: //-1/BC10816380D4/RXRULE/regxrule_profile_match_internal: Matched with rule 1 in ruleset 2
*Sep 4 17:57:59.001: //-1/BC10816380D4/RXRULE/regxrule_profile_match_internal: Matched with rule 1 in ruleset 2
*Sep 4 17:57:59.001: //-1/BC10816380D4/RXRULE/sed_subst: Successful substitution; pattern=011862196990 matchPattern=^01 replacePattern=011         replaced pattern=0111862196990
*Sep 4 17:57:59.001: //-1/BC10816380D4/RXRULE/regxrule_subst_num_type: Match Type = none, Replace Type = none Input Type = unknown
*Sep 4 17:57:59.001: //-1/BC10816380D4/RXRULE/regxrule_subst_num_plan: Match Plan = none, Replace Plan = none Input Plan = unknown
*Sep 4 17:57:59.001: //-1/BC10816380D4/RXRULE/regxrule_profile_translate_internal: xlt_number=0111862196990 xlt_type=unknown xlt_plan=unkn        own
*Sep 4 17:57:59.001: //-1/BC10816380D4/RXRULE/regxrule_profile_translate_internal: number= type=unknown plan=unknown numbertype=redirect-t        arget
*Sep 4 17:57:59.001: //-1/BC10816380D4/RXRULE/regxrule_get_RegXrule: Invalid translation ruleset tag=0
*Sep 4 17:57:59.001: //-1/BC10816380D4/RXRULE/regxrule_profile_match_internal: Error: ruleset for redirect-target number not found
*Sep 4 17:57:59.001: //-1/BC10816380D4/RXRULE/regxrule_profile_translate_internal: No match: number= type=unknown plan=unknown
*Sep 4 17:57:59.001: //-1/BC10816380D4/RXRULE/regxrule_profile_translate_internal: number= type=unknown plan=unknown numbertype=redirect-c        alled
*Sep 4 17:57:59.001: //-1/BC10816380D4/RXRULE/regxrule_get_RegXrule: Invalid translation ruleset tag=0
*Sep 4 17:57:59.001: //-1/BC10816380D4/RXRULE/regxrule_profile_match_internal: Error: ruleset for redirect-called number not found
*Sep 4 17:57:59.001: //-1/BC10816380D4/RXRULE/regxrule_profile_translate_internal: No match: number= type=unknown plan=unknown
*Sep 4 17:57:59.001: //-1/BC10816380D4/RXRULE/regxrule_dp_translate: calling_number=5024101498 calling_octet=0x0
        called_number=0111862196990 called_octet=0x0
        redirect_number= redirect_type=0 redirect_plan=0        redirect_PI=-1 redirect_SI=-1
*Sep 4 17:57:59.005: //-1/BC10816380D4/RXRULE/regxrule_vp_translate: No profile found in voice port or trunk group for outgoing direction
*Sep 4 17:57:59.005: //-1/BC10816380D4/RXRULE/regxrule_vp_translate: calling_number=5024101498 calling_octet=0x0
        called_number=0111862196990 called_octet=0x0
        redirect_number= redirect_type=0 redirect_plan=0
*Sep 4 17:57:59.005: ISDN Se3/0:1:23 Q931: Applying typeplan for sw-type 0x2 is 0x2 0x1, Calling num 5024101498
*Sep 4 17:57:59.005: ISDN Se3/0:1:23 Q931: Applying typeplan for sw-type 0x2 is 0x2 0x1, Called num
*Sep 4 17:57:59.005: ISDN Se3/0:1:23 Q931: TX -> SETUP pd = 8 callref = 0x008E
        Bearer Capability i = 0x8090A2
                Standard = CCITT
                Transfer Capability = Speech
                Transfer Mode = Circuit
                Transfer Rate = 64 kbit/s
        Channel ID i = 0xE9868398
                Exclusive, Interface 6, Channel 24
        Calling Party Number i = 0x2180, '5024101498'
                Plan:ISDN, Type:National
        Called Party Number i = 0xA1
                Plan:ISDN, Type:National
*Sep 4 17:57:59.133: ISDN Se3/0:1:23 Q931: RX <- RELEASE_COMP pd = 8 callref = 0x808E
        Cause i = 0x819C - Invalid number format (incomplete number)
*Sep 4 17:57:59.133: ISDN Se3/0:1:23 **ERROR**: call_cleared: VOICE ERROR: NULL VDEV Common(0xFC): bchan -1, call id 0x8016
*Sep 4 17:57:59.141: //-1/BC10816380D4/RXRULE/regxrule_stack_pop_RegXruleNumInfo: stack=0x6871D9EC; count=2
VoiceEncapPeer150
        peer type = voice, system default peer = FALSE, information type = voice,
        description = `',
        tag = 150, destination-pattern = `011.T',
        voice reg type = 0, corresponding tag = 0,
        allow watch = FALSE
        answer-address = `', preference=0,
        CLID Restriction = None
        CLID Network Number = `'
        CLID Second Number sent
        CLID Override RDNIS = disabled,
        source carrier-id = `', target carrier-id = `',
        source trunk-group-label = `', target trunk-group-label = `',
        numbering Type = `unknown'
        group = 150, Admin state is up, Operation state is up,
        Outbound state is up,
        incoming called-number = `', connections/maximum = 0/unlimited,
        DTMF Relay = disabled,
        URI classes:
            Destination =
        huntstop = disabled,
        in bound application associated: 'DEFAULT'
        out bound application associated: ''
        dnis-map =
        permission :both
        incoming COR list:maximum capability
        outgoing COR list:minimum requirement
        Translation profile (Incoming):Calling_Party_Num
        Translation profile (Outgoing):outgoing_international
        incoming call blocking:
        translation-profile = `'
        disconnect-cause = `no-service'
        advertise 0x40 capacity_update_timer 25 addrFamily 4 oldAddrFamily 4
        type = pots, prefix = `',
        forward-digits 0
        session-target = `', voice-port = `3/0:1:D',
        direct-inward-dial = enabled,
        digit_strip = enabled,
        register E.164 number with H323 GK and/or SIP Registrar = TRUE
        fax rate = system,   payload size = 20 bytes
        supported-language = ''
        preemption level = `routine'
        bandwidth:
            maximum = 64 KBits/sec, minimum = 64 KBits/sec
        voice class called-number:
            inbound = `', outbound = `'
        dial tone generation after remote onhook = enabled
        Time elapsed since last clearing of voice call statistics never
        Connect Time = 0, Charged Units = 0,
        Successful Calls = 0, Failed Calls = 15, Incomplete Calls = 0
        Accepted Calls = 0, Refused Calls = 0,
        Last Disconnect Cause is "1C ",
        Last Disconnect Text is "invalid number (28)",
        Last Setup Time = 50369257.
        Last Disconnect Time = 0.
T1 3/0:1 is up.
Applique type is Channelized T1
No alarms detected.
alarm-trigger is not set
Soaking time: 3, Clearance time: 10
AIS State:Clear LOS State:Clear LOF State:Clear
Version info of slot 3: HW: 1536, PLD Rev: 6
Framer Version: 0x58
Manufacture Cookie Info:
EEPROM Type 0x0001, EEPROM Version 0x04, Board ID 0x01,
Board Hardware Version 6.0, Item Number 73-4089-07,
Board Revision A0, Serial Number JAE08512FBJ,
PLD/ISP Version 48.53, Manufacture Date 13-Dec-2004.

Similar Messages

Trouble with implementing translation

I'm having some trouble getting my translation to work. I have a very basic application which is available in two languages. I have mapped and published my translation.
What I am trying to do is have the page translate when clicking the language button in the navigation bar. I created two navigation bar entries, which conditionally display based on the current value of FSP_LANGUAGE_PREFERENCE... My application globalization settings are set to "Item Level Preference"
The navbar entries are set as per following:
French entry
Redirects to page in application... &APP_PAGE_ID.
REquest: FSP_LANGUAGE_PREFERENCE
Set items: FSP_LANGUAGE_PREFERENCE
With these values: fr-ca
condition type: Request = en-ca
English entry
Redirects to page in application... &APP_PAGE_ID.
REquest: FSP_LANGUAGE_PREFERENCE
Set items: FSP_LANGUAGE_PREFERENCE
With these values: en-ca
condition type: Request = fr-ca
When I first run the application, I don't see any buttons... most likely because the request param is not set...
I'm using APEX 3.0... I've searched the forums and read the documentation, but nothing seems to work...
If anyone can point me in the right direction, I'd appreciate it
Thanks

Thanks guys for all your feedback... Part of the problem was my lack of understanding on how APEX handled the translation process.... I needed to "seed" my application whenever I made ANY change to the main application, to sync up my translated application.
I was able to get things working, and thought I'd share my findings with others if it can be of any use.... as well as get my implementation validated by more experienced apex developers such as yourselves...
The application globalization is configured to derive the language from an item level preference (app item FSP_LANGUAGE_PREFERENCE)
I started by creating an application computation to assign a default value to FSP_LANGUAGE_PREFERENCE with a computation point of "On new instance", static assignment = en-ca and with a condition that the application item FSP_LANGUAGE_PREFERENCE is null . For some reason, a computation point of "Before Header" was not setting it...
I then created an "onload: before header" conditional application process to redirect the page, if the REQUEST item = SETLANG. This is based on the post from Scott Spadafore Re: Application Preference (use FSP_LANGUAGE_PREFERENCE).
So the process will redirect to the current page if the REQUEST = SETLANG. This will ensure the NLS_* parameters are set according to the FSP_LANGUAGE_PREFERENCE... Joel Kallman's posts helped to understand why this is required... Re: Set FSP_LANGUAGE_PREFERENCE in URL
I created two navigation bar links, one for french and one for english... each one conditionally displays depending on the current FSP_LANGUAGE_PREFERENCE value (ie "English" link displays if FSP_LANGUAGE_PREFERENCE = fr-ca)
Each link will set the REQUEST item = SETLANG (this is the hook for the app process redirect), and also sets the FSP_LANGUAGE_PREFERENCE to target language. It will then redirect to the current page...
All this to flip between the english and french languages, on each page within my APEX application... thanks to all who posted solutions and tips...
Message was edited by:
pl_sequel
Message was edited by:
pl_sequel
Message was edited by:
pl_sequel

Trouble with internal keyboard and touchpad

Hi,
Yesterday I just out of nowhere started having some trouble with my keyboard and touchpad on my MacBook Air.
The problem displayed itself on various ways. One thing was that I couldn't press regulary with the touchpad. When I was pressing one time, it acted like a pressed with two fingers. When I tried to type in my password on the administrator page, some of the keys didn't work at all and some started to act weird. For example when I was pressing the letter B, the "bar" which displayes where you are in the text (don't know the word in English) went backwards, and when I pressed the letter F it went forward. This seemes so weird and also gives me a hope that it might be some setting failure though B stands for backwards and F stands for forward.
I could log in to the guestpage where I tried to write in "notes". In notes, no letters at all was working, only numbers. When I tried to shut the computer down from the apple symbol I was asked to write administrator name and password. When I tried to mark the name to write it, there wasn't a "bar" but a cross, but on the other hand did it work to write in the password field. But of course not B and F..
Usualy I'd just press the on/off botton until the computer lockdown, unfortunately the botton doesn't work. So the only thing I could do was to let the battery die and hope that it would start when I recharged it and pressed start, this didn't go as well as I hoped, so now I'm stuck with a dead macbook air.
Any ideas of what could be the problem or/and any solutions what might do the trick?
Extremly greatful for any answers

Yes you need to use a wired keyboard.

Trouble with internal microphone.

HP Pavilion dv6 Notebook PC
Windows 7 64 bit
unable to record or test internal microphone not listed
first time tried to use
IDT High Defintion Audio CODEC
Have gone through windows 7 sound guide troubleshooting for microphone
recording section not internal microphone listed
used accessories program sound recorder to test
no sound with playback

Hi,
Sounds like, somehow, you've got a feedback loop. All i can suggest is deleting Skype.
Sorry, that's all i've got!
Cheers,
SiR G.

Trouble with internal modem

Internal modem will not connect. I get a dialog message that states "pick up the phone and dial the number and when answered click OK and hang up phone." However, this does not connect me.
I purchased an exterior modem from Apple and it worked perfectly ONE TIME. On the second try the computer crashed --completely, could not force quit. Took computer to genius bar at Apple store, where a few things were tweaked. Went home and the external modem now gives me a message that it can not find a dial tone. Any suggestions?

as a guess, you could try booting the PowerBook from external hard drive with compatible OS on it to see if it's a software problem.
the fact that the PowerBook got frozen solid could mean a hardware issue, maybe USB port is flaky

SLS as Router: Trouble with internal hosts connecting to external IP.

I was hijacking [http://discussions.apple.com/message.jspa?messageID=12200257] long enough, so I'm moving this to my own question.
Setup: SLS 10.6.4 on Mac Mini(2010).
GigE en2 is connected to an internal network (hereafter 'lan')
USB Ethernet en0 (MacBookAir adapter) is connected to the external network (hereafter 'WAN').
Server has Two IP addresses, 'lan.lan.lan.2' and 'WAN.WAN.WAN.WAN'. Default route for server is 'WAN.WAN.WAN.GW'.
Server is serving NAT, DHCP, Firewall
Internal clients (such as 'lan.lan.lan.lan') trying to connect to 'WAN.WAN.WAN.WAN' (any port, any service) take about 13 SECONDS before they receive a reply.
External clients connecting to the WAN IP get served right away. ("The cobbler's children go barefoot").
Internal clients connecting to the internal IP (lan.lan.lan.2) are connected right away, also.
If I run 'route monitor' on the server during the 13 second connection, I see this:
bash-3.2# route monitor -n
got message of size 124 on Wed Sep 1 21:21:16 2010
RTM_LOSING: Kernel Suspects Partitioning: len 124, pid: 0, seq 0, errno 0, ifscope 0, flags:<UP,GATEWAY,HOST,DONE,WASCLONED,IFSCOPE>
locks: inits:
sockaddrs: <DST,GATEWAY>
lan.lan.lan.lan WAN.WAN.WAN.GW
Yes, it would be a losing route to try to reply out the WAN.WAN.WAN.GW for the internal address!
Furthermore, "traceroute -s WAN.WAN.WAN.WAN lan.lan.lan.lan" shows a route going OUT which of course fails.
Traceroutes of the LAN and WAN port on the server, show indeed that for the first several seconds, (until the RTM_LOSING message appears) the server tries to reply out the WAN port.
I've tried all sorts of static routes… to no avail
One odd thing: Why is the RTM_LOSING route IFSCOPEd to the external interface?
Any help is appreciated.
Yes, I'm definitely considering using a hardware router instead. But I'm really trying to avoid that- trying to save on space, power, heat here. The Mac is really a great box… If I can only get this fixed.
Thanks in advance to anyone who looks at this.
packet trace below: combined lan and [WAN] trace
Client on "lan.lan.lan.lan" port 50592
trying to connect to external IP WAN.WAN.WAN.WAN.80
[WAN] indicates replies sent out on the WAN port!
Note: also uploaded this to [http://pastebin.com/7hjfGUKH]
17:59:40.368696 IP lan.lan.lan.lan.50592 > WAN.WAN.WAN.WAN.80: Flags [S], seq 3990700560, win 65535, options [mss 1460,nop,wscale 1,nop,nop,TS val 649354945 ecr 0,sackOK,eol], length 0
17:59:40.368977 IP WAN.WAN.WAN.WAN.80 > lan.lan.lan.lan.50592: [WAN] Flags [S.], seq 702390106, ack 3990700561, win 65535, options [mss 1460,nop,wscale 2,nop,nop,TS val 899983692 ecr 649354945,sackOK,eol], length 0
17:59:40.912337 IP WAN.WAN.WAN.WAN.80 > lan.lan.lan.lan.50592: [WAN] Flags [S.], seq 702390106, ack 3990700561, win 65535, options [mss 1460,nop,wscale 2,nop,nop,TS val 899983697 ecr 649354945,sackOK,eol], length 0
17:59:41.319955 IP lan.lan.lan.lan.50592 > WAN.WAN.WAN.WAN.80: Flags [S], seq 3990700560, win 65535, options [mss 1460,nop,wscale 1,nop,nop,TS val 649354954 ecr 0,sackOK,eol], length 0
17:59:41.320185 IP WAN.WAN.WAN.WAN.80 > lan.lan.lan.lan.50592: [WAN] Flags [.], ack 1, win 65535, options [nop,nop,TS val 899983702 ecr 649354954], length 0
17:59:41.513346 IP WAN.WAN.WAN.WAN.80 > lan.lan.lan.lan.50592: [WAN] Flags [S.], seq 702390106, ack 3990700561, win 65535, options [mss 1460,nop,wscale 2,nop,nop,TS val 899983703 ecr 649354954,sackOK,eol], length 0
17:59:42.321320 IP lan.lan.lan.lan.50592 > WAN.WAN.WAN.WAN.80: Flags [S], seq 3990700560, win 65535, options [mss 1460,nop,wscale 1,nop,nop,TS val 649354964 ecr 0,sackOK,eol], length 0
17:59:42.321546 IP WAN.WAN.WAN.WAN.80 > lan.lan.lan.lan.50592: [WAN] Flags [.], ack 1, win 65535, options [nop,nop,TS val 899983712 ecr 649354964], length 0
17:59:43.322294 IP lan.lan.lan.lan.50592 > WAN.WAN.WAN.WAN.80: Flags [S], seq 3990700560, win 65535, options [mss 1460,nop,wscale 1,nop,nop,TS val 649354974 ecr 0,sackOK,eol], length 0
17:59:43.322464 IP WAN.WAN.WAN.WAN.80 > lan.lan.lan.lan.50592: [WAN] Flags [.], ack 1, win 65535, options [nop,nop,TS val 899983722 ecr 649354974], length 0
17:59:44.323703 IP lan.lan.lan.lan.50592 > WAN.WAN.WAN.WAN.80: Flags [S], seq 3990700560, win 65535, options [mss 1460,nop,wscale 1,nop,nop,TS val 649354984 ecr 0,sackOK,eol], length 0
17:59:44.323931 IP WAN.WAN.WAN.WAN.80 > lan.lan.lan.lan.50592: [WAN] Flags [.], ack 1, win 65535, options [nop,nop,TS val 899983732 ecr 649354984], length 0
17:59:45.325059 IP lan.lan.lan.lan.50592 > WAN.WAN.WAN.WAN.80: Flags [S], seq 3990700560, win 65535, options [mss 1460,nop,wscale 1,nop,nop,TS val 649354994 ecr 0,sackOK,eol], length 0
17:59:45.325235 IP WAN.WAN.WAN.WAN.80 > lan.lan.lan.lan.50592: [WAN] Flags [.], ack 1, win 65535, options [nop,nop,TS val 899983742 ecr 649354994], length 0
17:59:45.521364 IP WAN.WAN.WAN.WAN.80 > lan.lan.lan.lan.50592: [WAN] Flags [S.], seq 702390106, ack 3990700561, win 65535, options [mss 1460,nop,wscale 2,nop,nop,TS val 899983743 ecr 649354994,sackOK,eol], length 0
17:59:47.327098 IP lan.lan.lan.lan.50592 > WAN.WAN.WAN.WAN.80: Flags [S], seq 3990700560, win 65535, options [mss 1460,nop,wscale 1,nop,nop,TS val 649355014 ecr 0,sackOK,eol], length 0
17:59:47.327279 IP WAN.WAN.WAN.WAN.80 > lan.lan.lan.lan.50592: [WAN] Flags [.], ack 1, win 65535, options [nop,nop,TS val 899983762 ecr 649355014], length 0
17:59:51.330558 IP lan.lan.lan.lan.50592 > WAN.WAN.WAN.WAN.80: Flags [S], seq 3990700560, win 65535, options [mss 1460,sackOK,eol], length 0
17:59:51.330772 IP WAN.WAN.WAN.WAN.80 > lan.lan.lan.lan.50592: [WAN] Flags [.], ack 1, win 65535, options [nop,nop,TS val 899983801 ecr 649355014], length 0
17:59:53.537006 IP WAN.WAN.WAN.WAN.80 > lan.lan.lan.lan.50592: Flags [S.], seq 702390106, ack 3990700561, win 65535, options [mss 1460,nop,wscale 2,nop,nop,TS val 899983823 ecr 649355014,sackOK,eol], length 0
17:59:53.538328 IP lan.lan.lan.lan.50592 > WAN.WAN.WAN.WAN.80: Flags [.], ack 1, win 65535, length 0
17:59:53.538420 IP WAN.WAN.WAN.WAN.80 > lan.lan.lan.lan.50592: Flags [.], ack 1, win 65535, options [nop,nop,TS val 899983824 ecr 649355014], length 0
17:59:53.556404 IP lan.lan.lan.lan.50592 > WAN.WAN.WAN.WAN.80: Flags [P.], seq 1:164, ack 1, win 65535, length 163
17:59:53.556490 IP WAN.WAN.WAN.WAN.80 > lan.lan.lan.lan.50592: Flags [.], ack 164, win 65535, options [nop,nop,TS val 899983824 ecr 649355014], length 0
17:59:53.576007 IP WAN.WAN.WAN.WAN.80 > lan.lan.lan.lan.50592: Flags [.], seq 1:1449, ack 164, win 65535, options [nop,nop,TS val 899983824 ecr 649355014], length 1448
17:59:53.631457 IP lan.lan.lan.lan.50592 > WAN.WAN.WAN.WAN.80: Flags [.], ack 1449, win 65535, length 0
17:59:53.631541 IP WAN.WAN.WAN.WAN.80 > lan.lan.lan.lan.50592: Flags [P.], seq 1449:1527, ack 164, win 65535, options [nop,nop,TS val 899983824 ecr 649355014], length 78
17:59:53.632619 IP lan.lan.lan.lan.50592 > WAN.WAN.WAN.WAN.80: Flags [.], ack 1527, win 65535, length 0
17:59:53.656753 IP lan.lan.lan.lan.50592 > WAN.WAN.WAN.WAN.80: Flags [F.], seq 164, ack 1527, win 65535, length 0
17:59:53.656840 IP WAN.WAN.WAN.WAN.80 > lan.lan.lan.lan.50592: Flags [.], ack 165, win 65535, options [nop,nop,TS val 899983825 ecr 649355014], length 0
17:59:53.656920 IP WAN.WAN.WAN.WAN.80 > lan.lan.lan.lan.50592: Flags [F.], seq 1527, ack 165, win 65535, options [nop,nop,TS val 899983825 ecr 649355014], length 0
17:59:53.658263 IP lan.lan.lan.lan.50592 > WAN.WAN.WAN.WAN.80: Flags [.], ack 1527, win 65535, length 0
17:59:53.658383 IP lan.lan.lan.lan.50592 > WAN.WAN.WAN.WAN.80: Flags [.], ack 1528, win 65535, length 0
Message was edited by: the bee

Thank you for replying… ( +No, that's not the sound of desperation in my keystrokes…+ )
Anthony Bugera wrote:
First I created the file sysctl.conf (copy of sysctl.conf.default) in the /etc directory and added the following line:
net.inet.ip.scopedroute=0
I thought that's basically what I did, from the command line, but…
Second I installed Applejack 1.6, booted the server in single user mode, and issued the following command:
applejack auto restart
I wasn't sure what the purpose of AppleJack <http://applejack.sourceforge.net/> was here, but reading on…
Everything has been stable for over 3 hours. I did the scopedroute change with the conf file and rebooted because other people in other discussions have had limited success modifying the setting while the server was running (without *clearing the caches, aka applejack*, and rebooting).
Aha! There's probably a simple command line way to do this while running… somewhere… But, I'm willing to try it. I've already made the Mac our site's perimeter router, and I'm not quite ready to switch to a separate hardware router as the shiny new Mini ought to work.
But, some sort of cache being out of date, is a plausible reason for it "only working for a little while".
On the plus side, I'm getting a great TCP/IP re-education in the meanwhile.

Trouble with internal microphone and display

Hello together,
I just installed Arch on my Laptop yesterday. Everything works fine now, except for two things:
1) The internal microphone does not work at all. I already checked all settings in alsamixer/amixer and I also tried this, but it won't help.
2) After a reboot, the display brightness is always reduced. When I press the button to raise it again, nothning happens. When I press the button to lower it instead, it raises to the full brightness. This is a little strange and annoying, but not too important.
Does anyone have an idea how to fix that?
I would be grateful for any help.
cthl
EDIT:
I got the microphone working now, I was just a bit confused about the alsamixer/amixer settings.
Last edited by cthl (2013-11-03 17:20:28)

WonderWoofy wrote:Is that feedback? Are you sure it is not just the hum of your machine? I think of feedback as the screech you get when your mic actually starts picking up the output of the speakers.
Perhaps you're right - if so, I certainly didn't get as much background noise before. Any idea how to improve the situation?

Troubles with international sims

Purchased phone (3GS) unlocked, outright so no contract from Apple store in Australia.
Living in Denmark now and phone won't accept Danish sims. Guys in phone shop say phone is actually locked and he doesn't understand how it could be if it was supposed to be off contract. Software updates have been done regularly. They think that it shouldn't come up "connect to iTunes" when the Danish sim is installed.
Any hints would be welcome.

Have you made any progress with this? I have had what sounds like a similar issue when upgrading from 3.1.1sp2 to 3.2.2.
Keep us posted :-)

Trouble with international formats. Converting and storing in database.

Back again!
This time, I've got my app working as it should. I extract strings of information from a file, and store them appropriately in a database. Some of the data I cast to double as they are money values. The problem is this:
I'm storing the data in an access database. I need one of the values to be in European format. That is, using commas for decimal points and vice versa. Eg: $3.20, would become E3,20. (Don't know the shortcut for the Euro symbol).
I can't change swap commas to demimals points and THEN cast to double, because double wants american standard numbers. So how do I, or is there another way, to store the value in the database as:
E3,20 and not E3.20...??? I've changed the type in the access database column to Euro, so I get the Euro symbol...but if I put in a decimal, it stays a decimal.
Any ideas???
Thanks again.
...DJVege...

OK! And I'm lost again!!!! :-( Sorry, my bad!
Now, I've formatted the values perfectly in Java. But
unless I keep the type of column in Access as text,
they don't transfer over properly. If I keep them as
number, then only the numbers come over etc...If you have the numbers in Access as number and you can format numbers in Java then what is your problem? Without showing your code I (an most other non-mindreaders) don't have a chance. How are you getting the values form the Access database?
>
Also, do you know the custom format i need to use, so
that, even if I keep the column as text, Thjis does not make sense? I showed you two examples. What do you want in the way for format that they don't give.
it will
stick a � sign in front of it??? I don't understand! Show your code.
I figure, I'll just
stick to the text field, So you want to bodge it and leave the problem to someone else to deal with later on!
but somehow I need to stick
a � sign in front of it for display purposes.I have shown you how to format the numbers! I have suggested that the Euro symbol Unicode can be found using Google (it took me less than 30 seconds). What more can I do other than write the whole of your code for you?

Having trouble with international sim. Purchased phone unlocked, no contract from Apple store in Australia. Living in Denmark now and phone won't accept Danish sims. Guys in phone shop say phone is actually locked. Any hints would be welcome.

Purchased phone (3GS) unlocked, outright so no contract from Apple store in Australia.
Living in Denmark now and phone won't accept Danish sims. Guys in phone shop say phone is actually locked and he doesn't understand how it could be if it was supposed to be off contract. Software updates have been done regularly. They think that it shouldn't come up "connect to iTunes" when the Danish sim is installed.
Any hints would be welcome.

Hi Peter
Yes - it was from a proper Apple Store.
I only purchased the unit - no special requests and then went to O2 and hooked up with a scolling monthly sim.
I used that sim for about 6 months and then moved out here. I took on two PAYG sims, one for Qatar and one for UAE but neither are accepted.
When connect to my mbp, the phone screen shows the iphone connect cable and iTunes picks it up. The message then says " must insert original sim to register" My point - the original sim, was completely independant from the phone but I cant get past this point to do anything further.
Any thoughts?

PVC2300 - trouble with internal mic.

I have two PVC2300 cameras. So after a time in working conditions built-in microphones (of both cameras) begin to produce a noise, quite loud and disturbing. However, it happens both while operating on network adapter and PoE adapter. Cameras’ firmware has been updated to 1.1.2.6. But still there is aforesaid noise while filming with СISCO software as well as third-party one.
I get vide and audio from camera's over rtsp (rtsp://localip/img/media.sav)

These products are being handled by the Cisco Small Business Support Community.
The Search Function is your friend.... and Google too.
How to Secure your Network
How to Upgrade Routers Firmware
Setting-Up a Router with DSL Internet Service
Setting-Up a Router with Cable Internet Service
How to Hard Reset or 30/30/30 your Router

I have a Lucid 2 LG. I have been having trouble with insuffient storage. I have a 8G phone and have spent hours with Tier 2 tech trying to move info from the internal storage to the SD card with no luck, When I go to storage in the settings it states t

I have a Lucid 2 LG. I have been having trouble with insuffient storage. I have a 8G phone and have spent hours with Tier 2 tech trying to move info from the internal storage to the SD card with no luck, When I go to storage in the settings it states that over 4 gigs is for Misc? System data takes up over 4 gigs. No one can tell me what system data consist of. So My question is does anyone know what system data is? I am assuming I have a 8 gigphone but can only use 4 gigs???

System data is the OS or operating system. That is where the recovery stays separated from the rest of the storage so that it doesn't get corrupted. It is not accessible and non-movable.

Has anyone faced troubles with iPhone internal speaker?

Unfortunately, since I've bought my iPhone 4S less than 8 months, I'm facing troubles with the internal speaker of the phone.
It was enough just to restart the device to get the ringtone and speaker work.
But today, suddenly, the voice has disappeared again! I can hear the ppl calling me but no any other tones or rings r working.
I googled for a solution, and I was shocked that I found a lot of iPhone users r facing the same problem!
With all types of iPhone, seems it's been a long time problem with apple software that apple hasn't found a solution to it, nor admitting that they have such problem.
I need to get my phone fixed, but I do t want to lose my data, photos, a d programs..
And I DON'T WANT TO LEAVE MY PHONE AT A WORK SHOP! It's a HEADACHE?
So please if u have any other easy solutions to provide, I'll be so thankful.

Have you tried resetting your iPhone?
Reset: Press the Home and On/Off buttons at the same time and hold them until the Apple logo appears (about 10 seconds). Ignore the "Slide to power off"
A further troubleshooting step would be to backup your iPhone and then restore it as new using iTunes.

Trouble with DNS set up

Hello !
I've got a real trouble with my dns configuration... and i can't understand! so, i need some help....
well, qutie newbie in mac os server, i run in on a G4, and i had not noticed any trouble until i've decided to run open directory as a master with LDAP, wanting to have a kerberos protection for the users.
Kerberos doesn't want to play with me !
I've been in console mode to have a look, and, actually i've seen this :
"Oct 17 11:31:08 wakan servermgrd: servermgr_dns: no name available via DNS for 192.168.0.109
Oct 17 11:31:08 wakan servermgrd: servermgr_dns: no reverse DNS entry for server, various services may not function properly"
Ok... my DNS has a trouble... but i don't know how to fix it ! Is there anybody in this world who can help me?
I don't want to have a real DNS for my little server... but i understand that my config is not good. I can understand that having a caching DNS can improve the quality of my config, and, in other hand that it is necessary for having the services of OSX server in an effeciant way, but i don't know the way and the parameters i've to put in my config to fix it.
Now, just some words on my config...
First, i've got an adress provided by my FAI (the frenchy workd for ISP, i think) is "193.252.209.135". This adress is set on a d-link modem router via PPOE. The DNS of my provider (wanadoo.fr) are 80.10.246.1 and 80.10.246.132.
After this there is my G4 With mac osX server.
• en0, the "extenal gate" and the internal ethernet on the computer is plug on the modem with the adress "192.168.0.109". the router is set on "192.168.0.1". the dns are 80.10.246.1 and 80.10.246.132.
• en1, the "internal gate" for the network, an PCI card in the computer, has the parameters : adress "192.168.3.1", subnet "255.255.255.0", router "192.168.3.1". no dns records. (no VPN service for the moment). After this, i've a switch for the macs behind the server. (without any link agregation)
All those parameters have been set by the gateaway assistant.
And now the parameters inside the admin server :
DHCP : en1 - adress from 192.168.3.2 to 192.168.3.254, name 192.168.3. no static card. Router 192.168.3.1. No name for domaine by defaut, name servers 80.10.246.1 and 80.10.246.132 No LDAP, no WINS.
DNS : No zone transfert, recursivity is ON. No zone records.
NAT : set on full, Transfert and Network Address Translation.
When i've been on the terminal, i had those information:
"wakan:~ st$ sudo changeip -checkhostname
Password:
Primary address = 192.168.0.109
Current HostName = wakan.local
The DNS hostname is not available, please repair DNS and re-run this tool."
All my "main" services are working fine (AFP, Firewall, DHCP, DNS, Update) Open Directory is running without Kerberos. By the way, all the macs after the G4server can have a corect access to internet, and share information via LDAP of Open Directory, but i've to say that, a couple of days later, a friend of mine, who has a PC computer, can't have a DHCP dynamic address when he plug on my little network. I think that it is an other trouble, and i've decided to have e look to this later... but if someone knows how to resolve it...
So here begins the nightmare for me... so if anybody can help me... i realy need some help to fix this mystery!!!
Special thanks!

As the router modem is already doing NAT why use NAT in the server?
If you want to use OpenDirectory and other services you should/need to set up the DNS correctly using the server's private IP (and others in the same range the server is setup with). The domainname used internally can be different than your public one.
And then use the server as the only DNS for you LAN clients and the server itself. Forwarders (your ISP DNSes) in /etc/named.conf usually speeds up lookups of external addresses (also turning off IPv6 can help that too).

Performance with internal tables

Hi everybody,
I'm having trouble with the performance of a report.
The reports selects data out of many different tables and merges them together in one extraction file. (I would really like it to be executable in dialog task, because I don't want to write the file on the application sever)
I've done what I could using runtime analysis to improve performance of the db accesses. Now 97% of runtime is consumed by abap.
I'm using several internal tables which will have many entries, and at the moment I'm using nested loops to gather the information out of the internal tables into one extraction file. (Reading the internal tables with key is not always possible, I do this whenever possible)
I've tried to use loop... assigning <fs> instead of loop... into, but it doesn't really help too much.
Any other suggestions?
Thank you for your help, regards, Kathrin!

Hi,
Some of these might be able to help for improving the performance.
1. Read table with key using binary search.
2. While comparing two internal tables, user Kernal
   method. Eg: If I_TAB1[] = I_TAB2[]. Enfif.
3. Instead of appending records within loop/endloop,
   use 'Append lines of'.
4. When populate different internal tables, try to create
   with key field which will make a big difference while
   accessing the data.
5. Sort the internal tables.
6. Use Case/Endcase in place of If/Endif.
7. While making values negative, use 0 - <field>, in
   place of <field> * -1.
8. If the field structures are similar in two internal
   tables, for appending records use I_TAB2[] = I_TAB1[].
9. After the complete usage of internal tables, release
   the resources using FREE/FREFRESH <internal table>.
10. For data extraction, use field by field selection
    from database.
11. Try to avoid using 'ALL ENTRIES'. If using and make
    sure that the ref.internal table have entries.
12. Try using Inner Join using Foriegn key fields.
13. To get sum or count use Aggregate functions.
14. Try to use Views if need appropriately.
Hope this helps.
Gopakumar

Trouble with international translation

Similar Messages

Maybe you are looking for