Trying to install a Linksys WPS54GU2 wireless printer server with a Actiontec M1424WR router

Been trying to get the install software to "see" the router and never get past that. Have reset router and followed the cabling instructions but never get the installation software to list the server

You can try performing the setup manually. The Print Server device, if I'm not mistaken should have a web-browser configuration page you can tap into. It isn't as "simple" as a wizard should be, but it will rule out any issues relating to network discovery. Log into the ActionTec at http://192.168.1.1/ and see if you can locate the IP Address the Print Server is holding to the network. If you enter that address into your Web Browser, a configuration page should appear where you can enter in the Wireless settings manually, and continue on with following the installation steps outlined here: http://www6.nohold.net/Cisco2/ukp.aspx?pid=80&app=vw&vw=1&login=1&json=1&docid=59c0e1ff7adc408094106...
Since the Print server is supposed to support TCP/IP/SMB/Apple, setting up the Printer address should be nothing more than a matter of telling the computer to look for the Printer at a specific IP address/hostname. If you want a guide on how to do all of this, I'll gladly type one up. Before you disconnect the server from the Wired network and switch it over to Wireless, ensure your PCs can at least send jobs to the attached printer. If that's all set, then it's a matter of ensuring any printing-related settings on the PCs carry over on the switch to Wireless. Any issues with printing to the server (when it is on and pingable) would be due to an over-agressive firewall installed on a PC or due to a software (probably driver-related) issue that does not pertain to the print server.
I strongly suggest setting a Static IP on the Printer server, as an FYI. Hostnames can get iffy sometimes.
========
The first to bring me 1Gbps Fiber for $30/m wins!

Similar Messages

Printing to a Linksys Wireless Print Server with my MAC

have a small home network using an ATT DSL modem-router. I have several PCs hardwired to the router and 1 older MAC wireless. I have a MAC G4 laptop and a Dell laptop (my wife's) also connected wirelessly and all work well. I have added a Linksys wireless print server today and am able to get my wife's laptop to print easily and reliable as does the hardwired Dell. What I need is to get my MAC laptop to print wirelessly as well. I have tried all the options in the printer set-up but it does not see the print server. Linksys does not support MAC and there are no MAC drivers for the print server to download that I know of. Does anyone know of a fix on how I could configure this equipment so I can print wirelessly from my MAC laptop. Or perhaps bypass the print server and print using the modem-router and the same printer. I would appreciate any suggestions one could lend. Thanks much.
Power Book G4 17" Mac OS X (10.4.10) Virtual PC capable

Looking at figure 8-5 and the text to its left in the User Guide.
Click Add in Printer Setup, then select IP printer > IPP. Enter the print server's IP address AND queue name P1. With that info filled in OS X has all it needs to address the printer on the print server.
Download and install the CUPS driver version 1.1.0, and choose it when you Add in Printer Setup.

Sharing Linksys Wireless Print Server with MAC and PC - How to do?

I have lost the capability to share a printer on my network by using the Linksys Wireless Print Server-model number WPS54G -V2. Prior to having to return my previous Print Server on an RMA, I was able to use the MAC and PCs on my network. I have a PowerGook G4 with MacOS X 10.4.10. I also have a Airport Extreme Base Station V5.6. The printer on the network that is being shared is an Epson Stylus Photo 820. Recently, when trying to reconfigure the network, I updated the software on the Airport Extreme...so I think after that, I am no longer able to share this printer using current network configuration. As information, I will share how I got the network to share the printer BEFORE I had to replace the previous Print Server and BEFORE I updated the Airport Extreme. Please see this link:
http://www.macosxhints.com/article.php?story=20050406151311940
Even though this was for a different type of Print Server, this worked for me.
When reconfiguring the new Print Server, I contacted Linksys...as had some difficulty until I found out how to assign a static IP to the new Print Server. When trying to talk to them about the Mac issue, and sharing the printer, they shared this link with me...which may be helpful to some, but I found that this does not work for me...
http://www.macosxhints.com/article.php?story=20060404021600193
I have been trying to work through the issue, but feel I may now have some compatibility issues between the Airport Extreme and the Epson printer.
Further details are that I use 10.0.1.78 for the assigned IP address for the Print server. My router (which is the Airport address) is 10.0.1.1. I have tried IPP printing option, LPD printing option...and IPP printing at least returns a status on the Print Server as "printing" as opposed to "idle". I have checked the Print status on the Mac, and I have received two (2) different error messages as to why the print job failed. They are:
"the process "picwpstops" stopped unexpectedly with status 1"
and
"the process "rastertoprinter" stopped unexpectedly with status 1"
The latter happens when I follow the instructions on the second link I attached on this topic...with the only change being that I select IPP printing as opposed to LPD printing.
Anyone that has any insight into HOW to configure the mysterious settings for Mac OS printing so that it can be compatible with a Wireless Print Server, please feel free to comment. In the meantime, I am thinking that the links above could help some people...just not me at this point given my current configuration and versions of software/firmware and perhaps the printer I am using.
Greatly appreciate your consideration, and any suggestions to anyone that might understand what these error messages mean when checking the printer status after sending a file for printing.
Thank you

1. No, you don't have to make a bootable clone.
2. If you use the drive for a bootable backup, then you cannot use the drive for other types of storage unless you partition the drive and make more than one volume.
3. No, it will not try to boot the computer. You must designate the startup volume using Startup Disk preferences.
If you wish to use the drive on both a Mac and a PC, then either you make two partitions - one for Mac and the other for the PC or you must format the entire drive using FAT32 so the drive can be used for read//write by both operating systems. If you do this then you cannot use the drive for a bootable backup nor can you use it with Time Machine.
FAT32 is slower for read/write on the Mac than using Mac formatting.
Optimally, I would suggest you partition the drive into two volumes. One volume formatted for the Mac and the other formatted FAT32.
You can send files from a PC to a Mac and vice-versa using File Sharing. Select Mac Help from the Finder's Help menu and search for "file sharing" or "sharing" to find help articles. Also see,
Mac OS X 10.5 Help- Setting up a Mac computer to share files with Windows users
Mac OS X 10.5 Help- Setting up a Windows computer to share files with Mac users
Mac OS X 10.5 Help- Sharing with Windows computers

Wireless print server with Mac G4 and Dell PC's

I have a belkin wireless router and a linksys WPS54G print server. Hardwired by ethernet cables to the router are two computers 1) Dell 2400 and 2) Apple G4.
I am trying to get the Apple to print to the printserver. the linksys software set the Dell up and the print server and they work fine. I have tried everything i can on the Apple but no luck. Seems to be the driver. The printer is printing gibberish from the mac. The printer is an Epson Stylus Photo R320. I dowmloaded the drivers for Mac OS 10.4.4... from the epson website - I chose each one for the printer on my MAC and tried to print. The result was either no print out or differing gibberish each time. What can I do?

Please search this forum. Your precise issue has been covered several times. You have to use a CUPS driver for network printing - Epson's drivers are Carbon, not CUPS. Start by updating the Gimp-Print drivers that Apple included in OS X to the next newer version, now called Gutenprint 5.0.0:
http://sourceforge.net/project/showfiles.php?group_id=1537

Netgear WGPS606 wireless print server and HP1006

I have been trying to setup the Netgear WGPS606 wireless print server with my HP1006. The setup runs fine, finds the printer etc but when it comes to try to print a test page it is "unable to create a print job". When trying to print from Word etc I get similar message suggesting print test page/turn printer on/reinstall print drivers
I have spent hours with Netgear support who eventually said it MIGHT not be compatible
Before I bin it does anyone have any suggestions? I read somewhere it might be the USB drivers only work when connected directly to the PC (they're loaded up real time or something?) and to try using a serial driver instead?
Might that work, and if so does anyone know where I might find a suitable driver?
Thanks
J

I spent a month chasing my print server last year. Save yourself a month. The pad will find and print to airprint enabled printers. Period. It will not find a network print server.
Here is the list of printers, and some discussion.
http://support.apple.com/kb/ht4356

Linksys Wireless Print server WPS54G

Has anyone tried the Linksys WPS54G wireless print server to work on their Macbook? I don't use a wireless for general networking at home, can I still use the Wireless-G connection in ad-hoc mode to print using Macs?

You need to consider the driver for your printer first!!!!
Network printing/Windows printing only works with a driver that was meant for network printing. To use the OS X built-in CUPS network choices, you need a CUPS driver. For postscript printers, it's not an issue, because postscript is the native output of OS X, and can easily be routed to the various choices in Printer Setup.
Non-postscript printers are Very Different. Except for Brother, no manufacturer has provided CUPS drivers. Instead, what you get are Carbonized, OS9 legacy drivers, that have the comm protocol written into the driver (mostly USB). They can only print via local connection.
**Exception - when printing via an Airport/Bonjour enabled print server, where the software does a port redirection, USB output from the Mac gets routed to the USB port on Airport Express/Extreme.
Linksys doesn't do this Apple-only USB port redirection...

How to set up standalone wireless print server

I need step-by-step instructions on to set up a KonicaMinolta bizhub multifunction printer to print wirelessly from various Macs. In other words, it would not be hooked up to the internet or my wireless network. I understand this can be done with an AirPort Express or AirPort Extreme. I tried it with a Linksys WPSM54G wireless print server without success. I'd like to try the AirPort Express, but so far haven't been able to get it to work.
How do I configure my AExp to operate as a print server? How should I have it connected when I do the configuration?
How do I find the print server's IP address?
When I plug in the AExp and connect it to the printer via USB, the AExp flashes amber and never turns green (and therefore never connects with the MacBook).
If I successfully set up the print server as a separate network, can I be connected to the printer and my wireless network at the same time? Or do I need to switch back and forth?
If I'm accessing the internet via Ethernet, can I simultaneously access the printer via AirPort?
Any help will be greatly appreciated.

How do I configure my AExp to operate as a print server?
The AirPort Express Base Station (AX) or AirPort Extreme Base Station (AEBS) can only operate as a "print" server if the printer is attached to its USB port. Ethernet printers would require their own print server service if connected by Ethernet to either router.
How should I have it connected when I do the configuration?
Neither router would need a WAN port connection as both can provide a stand-alone wireless network. For a USB printer, it would need to be connected to the respective router's USB port.
How do I find the print server's IP address?
This would be the AirPort's LAN IP address. The default is: 10.0.1.1
When I plug in the AExp and connect it to the printer via USB, the AExp flashes amber and never turns green (and therefore never connects with the MacBook).
The flashing amber indicates that the AX has configuration issue. If you temporarily connect your MacBook directly to the AX's Ethernet port, and then, run the AirPort Utility, you can find out what the issue(s) is(are).
If I successfully set up the print server as a separate network, can I be connected to the printer and my wireless network at the same time? Or do I need to switch back and forth?
No, you would have to switch wireless networks. One way around this, is to have the AX configured to "Join a wireless network." This mode was specifically designed to allow the AX to perform as a wireless client and simultaneously provide both print sharing and iTunes streaming to network clients.
If I'm accessing the internet via Ethernet, can I simultaneously access the printer via AirPort?
Potentially, but your computer and the printer will be on separate broadcast domains/subnets.

Wireless Print Server (DPR-1260) - Manually Configure Printer Port

I am trying to get my DPR-1260 Wireless Print Server (PS) installed, and need help with manually configuring the printer port (per Dlink).
Status:
A) Before trying to install the PS, I was able to easily install (2) USB printers, see them, and print to them.
B) My new IMAC is hardwired to the router.
*Recent Actions:*
1) I've worked with Dlink and have verified that my network (my new IMAC, and my wife's wireless laptop (OS 10.39) see the PS (hooked directly to the router). It's IP address is 192.168.0.102 .
2) I hooked both printers to the PS, and the address sees both printers as installed, and provide with LPR information (both printers are now hooked to the PS). Dlink does not guarantee printer compatibility, but says that since the site sees the printers, gives me LPRs, that the probability is good that they will be compatiable.
3) My new IMAC sees this address in both OS and in XP (thru VM Fusion). My laptop (10.3x) also sees this address. However, I'm not able to install this printer.
4) Per Dlink, I need to manually configure the printer port to install the PS.
5) Dlink kept sending me to the Print Utility, but from what I see, that does not exist in 10.5.
How do I manually configure the printer port to see the PS?
Now, I am stuck, and help?
Many thanks

As DLink have said, you will have to manually configure a LPR queue to connect to your printers. The print utility in 10.5 is the Print & Fax util in System Preferences. Open this and choose to Add . Select IP and then LPR. Enter the ip address of the PS. Then you will need a queue name for the respective USB ports, such as P1 and P2, or something similar. Hopefully the DLink info mentions this so that you can print to the desired printer.
The final bit of info you will need to know is whether the printer driver for each printer will work in this type of network. If either of them is a Canon then there is a good chance you will not be able to use supplied drivers. These types of connections require a third party driver, like Gutenprint, which is usually installed by default. If you are not sure, then please tell us which brands and models of printer you have.
PaHu

Resolution - Printing HP LaserJet & Linksys Wireless Print Server WPS54GU2

Hello Guys:
After trying to figure out for 10 days and calling HP, Applet and Linksys support, i finally am able to print to my printer.
I have iMac running Tiger 10.4.8. I have a HP LaserJet 1012 Printer connected in a USB Port to the Wireless Print Server WPS54GU2. This is what I did to get it working.
First install the following drivers:
1) Go to http://www.linuxprinting.org/macosx/hpijs/ and download hpijs-foomatic-2.0.2.ppc.dmg and espgs-7.07.1.ppc.dmg file. Install hpijs first and espgs second.
2) After that Go to Server Preferences, Double click on Print/Fax.
3) Click on the "+" sign, select Line Printer Daemon - LPD
4) In the Address field, enter the IP address of your print server.
5) In the Queue name (This is very important). I used L2 for USB. You can try P1, L1 as well. Not sure how you have connected to the print server. For me L2 worked. I had tried using L1 and P1 and it didn't work for me.
6) The Name field should automatically be populated.
7) In the Print Using, select HP and then select "HP LaserJet 1012 Foomatic/hpijs" as the printer or whatever driver you have for your printer.
8) Click on Add
And now open up text edit or something and you should be able to print.
let me know if there are any questions.

Try Repairing permissions (Disk Utility). Then restart, then add again.
What do you mean by the printer doesn't show up - the driver (print using:)?
You can try the generic HP Photosmart P1100 Gimp-Print driver that comes in OS X.

How to connect to Linksys Wireless Print Server (WPS54GU2) from WIndows 7

I tried the Print Server Utility that was loaded from the WPS54GU2 user install disk. Ended up with an AddPort error.
Went ahead and created local printer for printer I was trying to get to (Epson Color Stylus 400). Did a "Printer Properties" on the printer after it is was created and clicked on the "Port" tab. Clicked on the "Add Port" button and selected "Standard TCP/IP Port" from list. Clicked on "New Port" . Wizard came up and clicked "Next" on this screen. I typed in the IP address of my Print Server (with no Port Name) and let it search for a while and it eventually failed. A screen came up requesting "additional port information" so I clicked on the "Custom" button and then clicked on the"Settings" button. Here I typed in the correct port name (which in my case was like LKxxxxxx where the x's are numerics). The IP address is already filed in. I checked the LPR button and made up a Queue Name and typed it into the Queue Name text box.
After clicking OK I tried printing to the printer and everything seemed to work correctly.
Message Edited by bionic_surfer on 11-14-2009 10:21 AM
Message Edited by bionic_surfer on 11-14-2009 10:21 AM

Corleone
I have the same issue as I have a new Windows 7 machine that is hardwired to my Linksys WPS54G. This is my main office PC and I have other computers throughout the house that are connected wirelessly to the WPS54G. I've tried to create a new port for printing based on the posts from other users but it still won't work. I've run the Linksys configuration and my PC sees the printer server. Am I missing a step?
Here is what I've done
Go to ports
Add new port
Standard TCP/IP Port
Click new port (Wizard comes up)
Enter printer name and IP address ( I enter my IP address for the Print Server 192.168.1.x)- Port name is same as IP Address (does this matter?)
Go to custom settings and set for LPR with Queue name of LP1 (or should it be L1?)
LPR Byte count box checked
Click next and finish
Do I need to restart my computer?
What am I missing
Thank you

I'm trying to install a Linksys wireless router. Went th...

I'm trying to install a Linksys wireless router. Went through the installation software and all appears to be in order. Except that the message that I'm getting is that my router is not signed into my internet connection. Yet it is--I'm writing this aren't I?
The 4 green lights are on and I've reviewed the installation instructions. Any help?

You need to make sure that you have an active internet connection from your ISP (Internet Service Provider). What connection are you using, CABLE or DSL ?

Linksys Wireless Print server and my Mac G4

I just set up my linksys wireless print server and it's printing from my PC just fine - not so on my G4. My printer is a Canon Pixma ip5200, and the appropriate drivers etc are installed.
I know the IP address and have tried setting up the printer via IPP (and pinged it from the mac successfully). Just no success printing. The printer utility looks like it is printing to the printer but nothing comes out.
Any ideas?

You won't be able to get this to work.
The Canon printer drivers won't allow you to connect to and print to a Canon printer attached to a wireless print server.
There is no solution, there is no way that this can work
You have three solutions.
Replace the Canon printer with another printer for which the drivers will work.
Replace the Canon printer with a networked Canon printer such as the iP4000r (or any other network printer) in which case you won't need the print server
Connect the Canon printer directly via USB to the computer to print.
iFelix

Linksys Wireless Print Server & HP Printer

Does anyone know if I can use my Linksys wireless print server which is attached to my HP All-in-One Inkjet printer for printing on my MacBook Pro? When I go to add a printer, nothing is detected - neither the HP or the Print Server.

I am facing the same problem too, except that my printer is a CANON. I can't seem to see the printer over the wireless network. However, when I connect the printer hardwired to my MBP, everything works fine and I am able to print normally.

Printing through Linksys Wireless Print Server

Ok.. Here is the question.
I have a Linksys Wireless Print Server (WPSM54G) which is connected to a Canon MX700. In windows this works great. However I cannot get OS X (10.5.2) to print to the printer.
The print server (with firmware update 1017) supports IPP, LPR, and some other printing protocols.
I have also pulled down the CUPS driver from Canon's site for the printer.
At this point I am stuck in getting this working.
Has anyone out there successfully gotten this wireless print server to work with OS X?
If so, what is the trick?
Thanks.

I hope you're right about supporting the industry-standard protocols after a firmware update - because this print server didn't support those before...
With the industry-standard protocols IPP and LPD, a queue name is a part of the address to direct data to the port on the print server. Do you know the queue name (also called port name in some documents) for this print server, so you can enter it in print & fax prefs?

I JUST BOUGHT AND INSTALLED A LINKSYS E1200 WIRELESS N ROUTER AT HOME. MY IPHONE CONNECTS WITH A STRONG SIGNAL BUT WHEN I TRY TO USE THE INTERNET IT JUST LOADS FOREVER. HOW CAN I FIX THIS?????!!!!

I JUST BOUGHT AND INSTALLED A LINKSYS E1200 WIRELESS N ROUTER AT HOME. MY IPHONE CONNECTS WITH A STRONG SIGNAL BUT WHEN I TRY TO USE THE INTERNET IT JUST LOADS FOREVER. HOW CAN I FIX THIS?????!!!!

RESET YOUR ROUTER
No. Reset your router.

Trying to install a Linksys WPS54GU2 wireless printer server with a Actiontec M1424WR router

Similar Messages

Maybe you are looking for