Trying to troubleshoot wireless & wired connections
If this type of question has already been addressed in a forum, please point me in the right direction!
I recently bought a Bluray player that requires an Ethernet connection to get online. I would like to be able to stream movies once in a while. My ISP is Time Warner, whose gateway device is next to the TV, but I would like to switch to AT&T Uverse, which would come into my apartment in the opposite corner of the room via the phone line. I would like to use Airport Extreme for my WiFi network, so I'm going to see if AT&T will provide me w/a wired modem that I can connect to it. I'm trying to figure out if it would then be possible to get some kind of secondary router to put over by the TV that would get the WiFi signal from my Airport and facilitate the Ethernet connection for the Bluray. Is this even possible? Advisable? I know the simplest thing would be to return this player for a WiFi enabled one, but I'm trying to see if I can make it work. Thanks for any advice.
I'm trying to figure out if it would then be possible to get some kind of secondary router to put over by the TV that would get the WiFi signal from my Airport and facilitate the Ethernet connection for the Bluray.
The AirPort Express can be configured to "join a wireless network" and the Ethernet port can be enabled to provide a signal, so it should work to provide an Ethernet connection to the DVD player.
Whether the wireless "hop" will allow enough bandwidth for good video performance is open to question. In that regard, it is going to be one of those "you will not know until you try" type of things. It might be a good idea to have a "Plan B" in case the AirPort Express does not work to your satisfaction.
The better way better way to do this would be to connect an Ethernet cable from the AirPort Extreme directly to the DVD player, as this type of connection provides much higher bandwidth than a wireless connection.
It goes without saying that you always want as much bandwidth as possible if you are planning to stream high definition video material.
Similar Messages
-
X1 AEBS, x2 Ax's and trying to decide wireless / wired
Hi,
My current set up is this - Satellite modem >>> AEBS >>> Cisco Aironet Bridge with Omni External antenna & 25metres ethernet wired to a Netgear router.
I will probably be able to disconnect the Netgear router from the current set up, as the building is picking up the wireless AEBS & Cisco bridge.
I have just tried setting up the AEBS and x2 Ax's to do WDS, and failed. I think the easiest solution for me is to hard wire from the AEBS to the Ax's, to then achieve wireless in 2 other buildings so I do not lose too much bandwidth from using the Ax's as bridges? (I believe this to be the case)
Can someone please point me in the right direction on how to set up the AEBS and Ax's so when the Ax is plugged into another building 50m away, it will still give wireless but be hard wired to the AEBS?
Is it possible that the AEBS would still be giving off a wireless signal?
Please help, step by step guide as the setting up of Ax's I am getting extremely confused with,
Regards, IanOK - update. Not quite sure what I did, but was able to get the thing connected with no security.
I plugged the AX directly into the computer AND had a wireless adapter plugged into the computer. Not sure which connection was being used to modify AX settings?? But got a good wireless connection in the end and was able to stream music.
BUT - I want to be able to add security. I'm trying to add WPA. My Buffalo Router says WPA-PSK. The AirPort Utility only lists WPA2, so I'm going through the Setup Assistant that has a WPA/WPA2 Personal option.
I went back and changed the security settings on the AX and it disappeared (no surprise). But when I change the security on the router, it fails to pick it back up.
Any suggestions on how to get WPA working for me? I don't want to leave my network open. -
Wrt54gs v7 wireless/wired connections
I recently replaced my BEFSR41 with the WRT54GS to add wireless capability to my home LAN. When I initially set up the new router I had trouble getting the wired ports to accept connection, finally got it set up, now cannot get wired ports to connect. My wireless is two new laptops running Vista, (We are having the usual problems of dropped connections due to cordless phones in our home and one of our neighbors, who also has a wireless network) I am trying to set a desktop running windows 2000 professional. The cable is the same one i have used before and the older router recognizes it, but when I disconnect and connect to the new router, the indicator light just flashes steadily and the connection monitor states that the cable is disconnected. Any suggestions to allow the desktop to access the network and internet would be helpful.
Reset the router back to factory default settings by pressing reset button on back panel of router… power down the router about a min. and power it back on check whether its connected to router and let me know the results…
-
AEBS Wired network fine, but wireless internet connectivity intermittent
I'm really frustrated by this one, because a large number of people are describing a very similar problem, but are using different terms, so most of the forum and discussion replies are based around resetting the AEBS or modem. Resetting my AEBS and modem DOES fix this problem for up to a couple of hours. Resetting my AEBS 15x per day is not a solution.
My AEBS has been serving me perfectly for over a year. I have been using two iMacs, an iBook G4, iPod Touch, iPhone, AX (802.11b/g), Wii and PSP on the network. One of the iMacs is connected by ethernet, everything else is wireless.
I am not using every item on this list at all times; in fact, I'm generally using 1-2 of them at any given time.
For the past 4-5 days, my wireless devices stop accessing the internet sporadically. They remain connected to the AEBS with a legit IP Address, but just sit there waiting to load whatever I'm trying to access. My AEBS has a legit IP Address from my ISP, and my iMac that's connected by ethernet is not experiencing the connectivity problems. My Wii is connected to Netflix, I can sometimes watch up to an hour of a movie and the load time is fantastic, but then it will stop and buffer for 15 minutes. During that time, my other wireless devices stop responding.
None of my devices are getting 'error' messages, they just sit there and wait. I get the 'loading' icon on my iPod Touch, and "connecting" in Safari on the iBook.
AEBS mode: Create wireless network, WPA/WPA2 Personal
5GHz network: different network name altogether for Wii (video streaming) and AX (music streaming). Problem persists on both bands of the network.
Access Control is currently off, problem persists when set to Timed and each device listed.
Please understand... I'm not trying to be rude, but my problem is not that the devices won't connect to the network, and it is not that they won't connect to the internet... it is that the internet connection is intermittent while the devices remain connected to the network with good signal and legit connection information. It is not my internet connection, because the problem does not exist on wired connections to the AEBS.
Any help would be greatly appreciated.Update:
After much testing and frustration, I have found out the following:
Two computers on default (2.4 GHz) network after factory reset tested extremely slow internet speed.
Intel iMac on 5 GHz network after factory reset (and dual-band enabled) tested normal speed (fast).
Same two computers on ethernet after factory reset tested normal speed (fast).
Same two computers on guest network after factory reset (and guest network enabled) tested extremely slow.
So... what I have here is reason to believe that there is either some kind of interference/interception on 802.11g network, in the 2.4 GHz band, or a bad component in the AEBS.
More troubleshooting, back in a bit. -
Thanks for the help. Looked but not clear on what I am trying to do as being possible. Can I use an Airport Express to connect wireless to a Linksys Wireless Router, such that I can then use the Ethernet ports on the Airport to either connected to a PC wired, or even use a hub off the Airport Express to allow multiple wired connections to it?
I am not looking to have the Airport Express extend my wireless network, just connect to it and provide me wired connections in a different location from where my Linksys Route is located. Would prefer to replace Linksys with all Apple, but just not possible financially yet. Thanks for the help.If the AirPort Express Base Station (AX) is an 802.11n model, then yes, you can reconfigure it as a wireless Ethernet bridge. In this configuration, the AX would join the wireless network provided by the Linksys router and its Ethernet port would be enabled for either a single wired device or for an Ethernet hub or switch for multiple devices.
-
I recovered a back up from my time machine via a wired connection after getting the 'white screen of death'. Now Time Machine does not recognise any back ups on the time machine when connected wirelessly and wants to do a first back up of the whole machine. How do I get my mac to recognise these older back ups? It connects to the wifi network the time machine creates fine, with the same name and password.
I recommend the following.
1. Reset the TC to factory.
Universal Factory Reset.. any model TC or AE.
Unplug your TC/AE from power or turn off at the power point.
Hold in reset. and power the TC/AE back on.. all without releasing reset and keep holding in for about 10sec. (this is often difficult without a 2nd person or a 3rd arm).
Release it when the status light flashes rapidly. If it doesn’t flash rapidly you have missed it and try again.
Note..
Be Gentle! Feel the switch click on. It has a positive feel.. add no more pressure after that.
TC/AE will reboot after a couple of minutes with default factory settings and will wipe out previous configurations of the router.
No files are deleted on the hard disk in a TC.. No reset of the TC deletes files.. to do that you use erase from the airport utility.
2. Rename the TC to SMB standard.
That means short names.. 2-20 characters but less than 10 is excellent. eg TCGenx (use number for x that is actual generation of the TC)
No spaces.
Pure alphanumeric. No apostrophe.
3. Ensure IPv6 is set to link-local..
Do the same thing for ethernet if that is used.
4. Manually mount the TC disk in Finder.
Use Go in the top menu.. connect to server.
Type in
AFP://TCname.local (where TCname is your new short name for the TC and local is default domain .. it helps using the domain I found).
You will then find the computer either can or cannot find the network resource.. if it fails something else is wrong with the actual network and you will need to fix that.
It will request the password if it is found.. password is public by default unless you changed it.. type in the password and check to keep it in your keychain.
5. Delete current TM setup and redo it with the newly named TC.
See A4 here. http://pondini.org/TM/Troubleshooting.html
If your backups cannot be found, try B6 again, now that you actually know that the disk has been properly discovered. -
[Solved] Wired connection ok but wireless problem on Intel 5100
Here is how i solved the problem :
1 - get back to the wiki doing everything in order
2 - added dbus in attition to hal in the deamon line in rc.conf
3 - put wicd at the end of the deamon line
4 - then configured wicd for my wireless network at boot : no more dbus error, and connection perfectly ok
Thx very much for the superb wiki, certainly my fault if i messed up but i still have to learn
Hi
I've got a problem with the wireless connection on my toshiba R10
my wired connection is working flawlessly but i can't use my wifi card. I'm using arch 2009.8 i686
Here is what i've done following the wiki :
1 : installed ifplugd for the RJ45 connection + added the deamon on my rc.conf
2 : installed wireless-tools
3 : installed the driver intel 5100
# pacman -S iwlwifi-5000-ucode
set up my mod_autolog yes
here is my ifconfig -a
[me@arch ~]$ ifconfig -a
eth0 Link encap:Ethernet HWaddr 00:1C:7E:83:EB:B4
inet addr:192.168.1.5 Bcast:192.168.1.255 Mask:255.255.255.0
inet6 addr: fe80::21c:7eff:fe83:ebb4/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:603 errors:0 dropped:0 overruns:0 frame:0
TX packets:610 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:100
RX bytes:329491 (321.7 Kb) TX bytes:84091 (82.1 Kb)
Memory:ffcc0000-ffce0000
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:66 errors:0 dropped:0 overruns:0 frame:0
TX packets:66 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:4400 (4.2 Kb) TX bytes:4400 (4.2 Kb)
wlan0 Link encap:Ethernet HWaddr 00:22:FB:04:1A:72
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
wmaster0 Link encap:UNSPEC HWaddr 00-22-FB-04-1A-72-00-00-00-00-00-00-00-00-00-00
UP RUNNING MTU:0 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
I have a dbus error : « Could not connect to wicd's D-Bus interface. Check the wicd log for error messages. »
so i modified my configuration file following this topic on the french forum http://forums.archlinux.fr/topic3967.html (same error message)
here is my rc.conf
# /etc/rc.conf - Main Configuration for Arch Linux
# LOCALIZATION
# LOCALE: available languages can be listed with the 'locale -a' command
# HARDWARECLOCK: set to "UTC" or "localtime"
# USEDIRECTISA: use direct I/O requests instead of /dev/rtc for hwclock
# TIMEZONE: timezones are found in /usr/share/zoneinfo
# KEYMAP: keymaps are found in /usr/share/kbd/keymaps
# CONSOLEFONT: found in /usr/share/kbd/consolefonts (only needed for non-US)
# CONSOLEMAP: found in /usr/share/kbd/consoletrans
# USECOLOR: use ANSI color sequences in startup messages
LOCALE="fr_FR.utf8"
HARDWARECLOCK="localtime"
USEDIRECTISA="no"
TIMEZONE="Europe/Paris"
KEYMAP="fr-pc"
CONSOLEFONT=
CONSOLEMAP=
USECOLOR="yes"
# HARDWARE
# MOD_AUTOLOAD: Allow autoloading of modules at boot and when needed
# MOD_BLACKLIST: Prevent udev from loading these modules
# MODULES: Modules to load at boot-up. Prefix with a ! to blacklist.
# NOTE: Use of 'MOD_BLACKLIST' is deprecated. Please use ! in the MODULES array.
MOD_AUTOLOAD="yes"
#MOD_BLACKLIST=() #deprecated
MODULES=()
# Scan for LVM volume groups at startup, required if you use LVM
USELVM="no"
# NETWORKING
# HOSTNAME: Hostname of machine. Should also be put in /etc/hosts
HOSTNAME="arch"
# Use 'ifconfig -a' or 'ls /sys/class/net/' to see all available interfaces.
# Interfaces to start at boot-up (in this order)
# Declare each interface then list in INTERFACES
# - prefix an entry in INTERFACES with a ! to disable it
# - no hyphens in your interface names - Bash doesn't like it
# DHCP: Set your interface to "dhcp" (eth0="dhcp" )
# Wireless: See network profiles below
#Static IP example
#eth0="eth0 192.168.0.2 netmask 255.255.255.0 broadcast 192.168.0.255"
eth0="dhcp"
INTERFACES=(eth0)
# Routes to start at boot-up (in this order)
# Declare each route then list in ROUTES
# - prefix an entry in ROUTES with a ! to disable it
gateway="default gw 192.168.0.1"
ROUTES=(!gateway)
# Enable these network profiles at boot-up. These are only useful
# if you happen to need multiple network configurations (ie, laptop users)
# - set to 'menu' to present a menu during boot-up (dialog package required)
# - prefix an entry with a ! to disable it
# Network profiles are found in /etc/network.d
# This now requires the netcfg package
#NETWORKS=(main)
# DAEMONS
# Daemons to start at boot-up (in this order)
# - prefix a daemon with a ! to disable it
# - prefix a daemon with a @ to start it up in the background
DAEMONS=(syslog-ng hal network ifplugd netfs slim crond alsa fam)
i tried to start wicd manually but it stay busy infinitely :
here is my /etc/wicd/manager-setting.conf
GNU nano 2.0.9 Fichier : /etc/wicd/manager-settings.conf
[Settings]
wireless_interface = wlan0
pref_width = 450
window_width = 530
prefer_wired = False
flush_tool = 0
use_global_dns = False
global_dns_dom = None
always_show_wired_interface = True
sudo_app = 0
global_dns_1 = None
global_dns_2 = None
global_dns_3 = None
backend = external
link_detect_tool = 0
dhcp_client = 0
window_height = 529
wired_connect_mode = 1
debug_mode = 0
sudo_app = 0
global_dns_1 = None
global_dns_2 = None
global_dns_3 = None
backend = external
link_detect_tool = 0
dhcp_client = 0
window_height = 529
wired_connect_mode = 1
debug_mode = 0
pref_height = 450
wired_interface = eth0
signal_display_type = 1
global_search_dom = None
auto_reconnect = True
wpa_driver = wext
and what i get ont the graphical interface : no wireless network found
here is my "ps aux | grep dbus"
[root@arch ~]# ps aux | grep dbus
dbus 1373 0.0 0.0 2252 940 ? Ss 14:27 0:00 /usr/bin/dbus-daemon --system
me 1703 0.0 0.0 3156 696 ? S 14:27 0:00 /usr/bin/dbus-launch --sh-syntax --exit-with-session
me 1704 0.0 0.0 2264 972 ? Ss 14:27 0:00 /usr/bin/dbus-daemon --fork --print-pid 5 --print-address 7 --session
root 2794 0.0 0.0 3892 872 pts/1 S+ 15:11 0:00 grep dbus
in the preference settings of wicd, it's correct : eth0 as wired connection and wlan0 as wireless
here is my "iwlist wlan0"
[root@arch ~]# iwlist wlan0 scanning
wlan0 No scan results
i've tried a lspci -vv :
[me@arch ~]$ lspci -vv
00:00.0 Host bridge: Intel Corporation Mobile 4 Series Chipset Memory Controller Hub (rev 07)
Subsystem: Toshiba America Info Systems Device 0001
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
Kernel driver in use: agpgart-intel
Kernel modules: intel-agp
00:03.0 Communication controller: Intel Corporation Mobile 4 Series Chipset MEI Controller (rev 07)
Subsystem: Toshiba America Info Systems Device 0001
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 0: Memory at ffcff000 (64-bit, non-prefetchable) [size=16]
Capabilities: <access denied>
Kernel driver in use: heci
Kernel modules: heci
00:19.0 Ethernet controller: Intel Corporation 82567LM Gigabit Network Connection (rev 03)
Subsystem: Toshiba America Info Systems Device 0001
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 28
Region 0: Memory at ffcc0000 (32-bit, non-prefetchable) [size=128K]
Region 1: Memory at ffcfe000 (32-bit, non-prefetchable) [size=4K]
Region 2: I/O ports at cf80 [size=32]
Capabilities: <access denied>
Kernel driver in use: e1000e
Kernel modules: e1000e
00:1f.0 ISA bridge: Intel Corporation ICH9M-E LPC Interface Controller (rev 03)
Subsystem: Toshiba America Info Systems Device 0001
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
Kernel modules: iTCO_wdt
01:00.0 Network controller: Intel Corporation Wireless WiFi Link 5100
Subsystem: Intel Corporation Device 1301
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 29
Region 0: Memory at ff900000 (64-bit, non-prefetchable) [size=8K]
Capabilities: <access denied>
Kernel driver in use: iwlagn
Kernel modules: iwlagn
I suspect that something is wrong between iwlagn and iwlwifi-5000 which can cause this problem.
I have to say that I'm quite lost here, i hope someone will have an idea
thank you very much
Last edited by Janarto (2009-08-30 02:46:18)Stab in the dark...the hal daemon should start dbus, but sometimes I've been encouraged to add the dbus DAEMON explicitly (before hal).
I don't really understand dbus too intimately, but I've come across situations where although dbus is running, I can't talk to it because the DBUS_SESSION_BUS_{ADDRESS,PID,WINDOWID} variables weren't visible in the environment I was working in. For instance, if dbus is started by xinitrc, and then some system-level daemon tries to talk to dbus, usually it fails for me, and I have to use some workaround.
Now I would expect wicd to be set up so that the ordinary user doesn't encounter any problems of this sort. On the other hand, the error you're getting does say that it's dbus communication which is failing. Perhaps you could try shutting down hald and dbus, open a terminal, su -, /etc/rc.d/dbus start, and then try from that command line to tell wicd to connect? -
Qos - giving wired connections priority over wireless connections
I have a WRT54G with revised firmware. I have one wireless connection and one wired connection. I'd like to set it up so that the wired connection uses the majority of the bandwidth. This way the resource intensive programs I use for work (CAD, GIS, etc accessing files remotely) will be guaranteed to have available more bandwith than my daughter on her laptop using IM, web cam and WOW-type game play. I don't mind her using these programs, but I have to make my work a priority.
It seems that I can shape traffic if each were a WIRED connection and also that the single QoS option for wireless will enhance WiFi MultiMedia. How can I assign a preference to the WIRED connection and provide a smaller but usable portion of bandwith to the wireless connection?
Thanks in advance.Thanks for the input, although I still am a bit lost. I apologize if my questions appear repetitive.
You wrote:
==========
Make the Upstream Bandwidth service "manual" with the Kbps speed you want to dedicate to that application........
==========
What do you mean by "dedicate to that application?" Do you mean the apps I am trying to give bandwidth priority too? If so, how much of the 512 kbs upstream bandwidth do I enter here? How does this affect the wireless connections?
You wrote:
==========
You can provide priority to Devcie with MAC address & also the Etherent Port on four ports with different priority .....
Use application name also .....
=============
Won't these only apply to the different ethernet ports and wired MAC addresses? I am trying to limit bandwith to the wireless side...
You wrote:
==========
Under Wireless QoS .... enable the service
==========
Won't this provide the wireless connection with more efficient throughput? How will this help me in limiting the bandwith allocated to the wireless connection?
Thanks for your reply. -
Slow Internet on wired connection, fast wireless on same network
Hi,
My Internet connection has just been upgraded from 2MB/s to 10MB/s. To confirm the upgrade I have used www.speedtest.net with Firefox 3.5.1 to test my upload/download speeds. I have 2 computers on my network which consists of a cable modem connected to a white airport base station with 128 bit WEP encryption in 802.11 b/g compatible mode. The 2 computers are a dual 2.8 ghz MacPro which is wired directly into the Airport base station by Ethernet and an iMac 1.83 Intel core 2 duo which connects wirelessly. Both machines are running OS X 10.5.7. The much faster MacPro only achieves a download speed of 5.7MB/s over its wired connection while the slower iMac achieves 9.8MB/s - very close to the advertised speed over its wireless connection. Both upload at the same 512kb speed. These are consistent speeds not one offs so I am wondering why the difference? The MacPro is my main machine so I'd like to have the best speed possible on that.
I have tried connecting the MacPro directly to the Cable Modem, bypassing the airport base station and get the same speeds.
Any ideas? What else can I try?
Thanks for reading all that, I've put in as many details as possible, I'm really stumped!
Thanks in advance,
Alan.Alan Holwill wrote:
I have 2 computers on my network which consists of a cable modem connected to a white airport base station with 128 bit WEP encryption in 802.11 b/g compatible mode. [snip] The much faster MacPro only achieves a download speed of 5.7MB/s over its wired connection while the slower iMac achieves 9.8MB/s - very close to the advertised speed over its wireless connection. Both upload at the same 512kb speed. These are consistent speeds not one offs so I am wondering why the difference?
I have tried connecting the MacPro directly to the Cable Modem, bypassing the airport base station and get the same speeds.
First, be sure you're not confusing "MB/s" (megabytes/sec) and "Mb/s" (megabits/sec). These will normally differ by (roughly) a factor of 10. The value of "9.8MB/s" over 802.11g is presumably actually "9.8Mb/s", as the higher value exceeds the maximum rate for that protocol.
Second, what type of Ethernet cable ("CAT-x") are you using? An older cable can cut your maximum data rate.
What speed do you see with the iMac if you connect it via Ethernet? -
QuickVPN problem - Wireless no connect, wired connect
I'm trying to connect to an RVS4000 at the office using QuickVPN on a laptop.
My home router is a WRV54G. After spending way too much time trying to get this thing to work using the wireless connection to the laptop I tried installing the client on my desktop and it worked. I then tried connecting the laptop to the wired connection and it worked also. It appears as though the wireless connection is the problem. I installed the newest version of the client I could find to another laptop and had the same problem on the wireless. Yet I can connect using TheGreenbow on another laptop to another VPN over this same wireless connection.
Wasting way too much time on this one... Any Ideas?Do you mean you cant connect to the quick vpn using your wireless computer? And then if you connect the wireless laptop directly(hardwired) to the router , you can connect to the quick vpn? Have you tried other wireless computer to check if you can connect to your quick vpn?
-
I am trying to setup wireless using my old dome Airport Extreme Base station. I had previously used it about 5 years ago when I had dial up but have now switched to DSL with Windstream. I can not get connected as the ABS keeps trying to dial up(the old phone number). When I tried to change my network settings an annoying popup window says "your network settings have been changed by another application'. I have no idea what the message is all about and when I close this window it immediately pops up again and prevents me -as far as I can tell -from changing my Airport settings? I need advice on how to get this wireless setup done. Maybe a reset? or something else? I have the DSL phone line plugged into WIndsteam Seimens Speedstream 4200 modem and then the ethernet (yellow) wire from the WIndsteam Seimens Speedstream 4200 modem to the port on the dome that is a circle of dots.
1)Can you explain how using the AEBS as a bridge will work with the Seimens Speedstream4200?
As a bridge, the AEBS will basically become a wireless access point. This will allow the AEBS to provide a wireless network, but still allow the Speedstream to provide NAT & DHCP services for the wireless clients connected to the AEBS. If the AEBS was left as a router, you would have a double-NAT condition which isn't necessary bad in itself, but would create a second subnet. That would make it more difficult for clients connected to the AEBS to access clients connected to the Speedstream.
2) Is there a link that will guide me through the steps to set the AEBS as a bridge?
You can easily reconfigure the AEBS as a bridge using the AirPort Utility.
ref: AirPort Utility > Select the AEBS > Manual Setup > Internet > Internet Connection > Connection Sharing = Off (Bridge Mode)
3)Can I just connect the DSL phone line to the AEBS and eliminate the Speedstream4200?
Unfortunately no. The AEBS does not have a built-in DSL modem. You will still need the Speedstream to provide this function. -
How do I disconnect from Wireless to use wired connection?
Hi - I'm new to this and I apologize if this question is ridiculously easy.
I am using a cable modem in which I have plugged my WRT160Nv2 wireless router. I am supporting three computers here in my home; my laptop (both wired and wireless), my daughters laptop (wireless only), and my desktop (wired only).
Everything works great and I have to give all the credit to CISCO and the excellent software which automatically solves every connection problem that comes up.
My laptop and desktop are connected to the wireless router via cable.
My question is strictly about my laptop. When I leave my office in the house and go into another room, I establish the wireless connection. Now I am back in my home office room, I want to use my wired connection. How do I do this? Do I need to disable my wireless connection so that my wired connection takes over? Again, I do have my laptop connected to the wireless router via cat5.
I want to do this strictly for the speed of the connection. I've read that a wired connection is double if not more in Mbps.
This laptop is running Win XP Pro, SP3.
I hope this furnishes enough info to assist in an answer.
Thanks in advance.
John
P.S.. I really do want to educate myself regarding the equipment I am using and not have to ask such basic questions. Are there any books or websites you can recommend that can start me out and go as technical as I choose to?Windows by default uses the fastest connection possible. If you have a wireless and wired connection active at the same time it depends on how fast both connections are rated. Wireless connections tend to change depending on the distance. Wireless 802.11g goes up to 54 Mbit/s. Wireless 802.11n can go up to some 300 Mbit/s. Wired connections are usually either gigabit ethernet (1000 Mbit/s) or fastethernet (100 Mbit/s).
Thus, which is picked depends on your computer. You should check the connection status of both connections in the network connections control panel. It shows you the current wireless and wired speed (the latter won't change of course). Very often, the wired connection is preferred to the wireless connection. Now with 802.11n connections the wireless connection is preferred if your wired connection is only fastethernet.
As your WRT160Nv2 has only FastEthernet LAN ports you have to check how fast the wireless connection is. If you have a 802.11n wireless adapter in your laptop it may show up the wireless connection faster then 100 Mbit/s. Depending on the setting it may change occassionally between 54 Mbit/s and speeds higher then 100 Mbit/s which would lead Windows to swap connections. If you see that problem it is better to switch off the wireless in the laptop while you have a wired connection...
A wired connection is more reliable and stable then a wireless connection. With wireless you can have interference. Thus, even though a wired connection may be slower then a wireless one you may prefer to use the wired connection anyway. And some people prefer to turn off the wireless to avoid radiation.
To sum up: usually you don't have to switch off the wireless, unless you experience problems because of the mentioned changing speeds of the wireless connection. The computer will always only use one connection. Not both. -
I just set up the airport wireless modem - with a comcast internet router - all wireless device connect seemlessly (3 Iphones, Mac Air, and a Sony Laptop) but my IPAD 1 no longer connects. It tries to but never connects. I have reset it and have airprot utility app downloaded on my IPAD - it shows the modem and the internet no connected?
Do you mean an Airport Extreme Base Station connected to a Comcast Modem?
-
Can't connect to D-Link router. Both Wireless and Wired connection.
Hi guys,
So I've had this problem for a really long time. I am unable to connect to my D-Link router. My laptop used to be able to connect to this router before. I was using my laptop then all of a sudden I was disconnected from the wifi connection.
I tried to connect back to it but it said that I needed to be in range. I'm tethering off my phone atm to write this post. I'm currently right beside the router but it still gives me the same message. Sometimes it'll just say that
windows cannot connect to the hidden network. I tried using an ethernet cable to directly connect via LAN, it worked for awhile, but recently now it says that I don't have a valid IP configuration. I've looked through many forums and threads and
tried their "fixes" but I guess it still wasn't my "fix". I have gone into CMD and did the ipconfig /all command and here are my details:
Microsoft Windows [Version 6.1.7600]
Copyright (c) 2009 Microsoft Corporation. All rights reserved.
C:\Users\apagtalunan>ipconfig
Windows IP Configuration
Wireless LAN adapter Wireless Network Connection 2:
Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :
Wireless LAN adapter Wireless Network Connection:
Connection-specific DNS Suffix . :
Link-local IPv6 Address . . . . . : fe80::4d38:b408:8509:4c3b%11
IPv4 Address. . . . . . . . . . . : 192.168.43.142
Subnet Mask . . . . . . . . . . . : 255.255.255.0
Default Gateway . . . . . . . . . : 192.168.43.1
Ethernet adapter Local Area Connection:
Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :
Tunnel adapter Reusable Microsoft 6To4 Adapter:
Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :
Tunnel adapter Local Area Connection* 11:
Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :
Tunnel adapter Local Area Connection* 27:
Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :
Tunnel adapter 6TO4 Adapter:
Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :
Tunnel adapter Local Area Connection* 12:
Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :
Tunnel adapter Local Area Connection* 13:
Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :
Tunnel adapter Local Area Connection* 14:
Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :
Tunnel adapter Local Area Connection* 15:
Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :
Tunnel adapter Local Area Connection* 16:
Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :
Tunnel adapter Local Area Connection* 17:
Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :
Tunnel adapter Local Area Connection* 18:
Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :
Tunnel adapter Local Area Connection* 19:
Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :
Tunnel adapter Local Area Connection* 21:
Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :
Tunnel adapter Local Area Connection* 22:
Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :
Tunnel adapter Local Area Connection* 20:
Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :
Tunnel adapter Local Area Connection* 23:
Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :
Tunnel adapter Local Area Connection* 24:
Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :
Tunnel adapter Local Area Connection* 26:
Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :
Tunnel adapter Local Area Connection* 25:
Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :
Tunnel adapter Local Area Connection* 28:
Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :
Tunnel adapter Local Area Connection* 30:
Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :
Tunnel adapter Local Area Connection* 39:
Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :
Tunnel adapter Local Area Connection* 29:
Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :
Tunnel adapter Local Area Connection* 31:
Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :
Tunnel adapter Local Area Connection* 33:
Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :
Tunnel adapter Local Area Connection* 34:
Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :
Tunnel adapter Local Area Connection* 36:
Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :
Tunnel adapter Local Area Connection* 37:
Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :
Tunnel adapter Local Area Connection* 35:
Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :
Tunnel adapter Local Area Connection* 38:
Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :
Tunnel adapter Local Area Connection* 40:
Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :
Tunnel adapter Local Area Connection* 45:
Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :
Tunnel adapter Local Area Connection* 43:
Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :
Tunnel adapter Local Area Connection* 50:
Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :
Tunnel adapter Local Area Connection* 52:
Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :
Tunnel adapter Local Area Connection* 53:
Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :
Tunnel adapter Local Area Connection* 56:
Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :
Tunnel adapter Local Area Connection* 58:
Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :
Tunnel adapter Local Area Connection* 57:
Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :
Tunnel adapter Local Area Connection* 70:
Connection-specific DNS Suffix . :
IPv6 Address. . . . . . . . . . . : 2001:0:9d38:6ab8:103c:2f0e:3f57:d471
Link-local IPv6 Address . . . . . : fe80::103c:2f0e:3f57:d471%79
Default Gateway . . . . . . . . . : ::
Tunnel adapter isatap.{68D1DDD2-DEE1-44CF-B523-24A567A2CF67}:
Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :
C:\Users\apagtalunan>
Not sure if this "Tunnel adapter" should even be there. Anyways, my laptop is a MSI-CR600. I've had it for awhile now, past warranty and whatnot. Never called and brought it back to the manufacturer. D-Link router is
DIR-825. And to narrow it down even more, I can connect to my friend's router, aslo at my church, and my girlfriend's place. If there is any other info needed to help solve this problem, just let me know. I'll do what I can. Thanks!
(Oh, and everything is up to date! Drivers, etc.)
-AlomarAutoconfiguration Enabled . . . . : Yes
Tunnel adapter Local Area Connection* 18:
Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : Microsoft 6to4 Adapter #10
Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0
DHCP Enabled. . . . . . . . . . . : No
Autoconfiguration Enabled . . . . : Yes
Tunnel adapter Local Area Connection* 19:
Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : Microsoft 6to4 Adapter #11
Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0
DHCP Enabled. . . . . . . . . . . : No
Autoconfiguration Enabled . . . . : Yes
Tunnel adapter Local Area Connection* 21:
Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : Microsoft 6to4 Adapter #13
Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0
DHCP Enabled. . . . . . . . . . . : No
Autoconfiguration Enabled . . . . : Yes
Tunnel adapter Local Area Connection* 22:
Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : Microsoft 6to4 Adapter #14
Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0
DHCP Enabled. . . . . . . . . . . : No
Autoconfiguration Enabled . . . . : Yes
Tunnel adapter Local Area Connection* 20:
Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : Microsoft 6to4 Adapter #12
Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0
DHCP Enabled. . . . . . . . . . . : No
Autoconfiguration Enabled . . . . : Yes
Tunnel adapter Local Area Connection* 23:
Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : Microsoft 6to4 Adapter #15
Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0
DHCP Enabled. . . . . . . . . . . : No
Autoconfiguration Enabled . . . . : Yes
Tunnel adapter Local Area Connection* 24:
Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : Microsoft 6to4 Adapter #16
Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0
DHCP Enabled. . . . . . . . . . . : No
Autoconfiguration Enabled . . . . : Yes
Tunnel adapter Local Area Connection* 26:
Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : Microsoft 6to4 Adapter #18
Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0
DHCP Enabled. . . . . . . . . . . : No
Autoconfiguration Enabled . . . . : Yes
Tunnel adapter Local Area Connection* 25:
Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : Microsoft 6to4 Adapter #17
Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0
DHCP Enabled. . . . . . . . . . . : No
Autoconfiguration Enabled . . . . : Yes
Tunnel adapter Local Area Connection* 28:
Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : Microsoft 6to4 Adapter #20
Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0
DHCP Enabled. . . . . . . . . . . : No
Autoconfiguration Enabled . . . . : Yes
Tunnel adapter Local Area Connection* 30:
Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : Microsoft 6to4 Adapter #22
Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0
DHCP Enabled. . . . . . . . . . . : No
Autoconfiguration Enabled . . . . : Yes
Tunnel adapter Local Area Connection* 39:
Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : Microsoft 6to4 Adapter #30
Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0
DHCP Enabled. . . . . . . . . . . : No
Autoconfiguration Enabled . . . . : Yes
Tunnel adapter Local Area Connection* 29:
Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : Microsoft 6to4 Adapter #21
Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0
DHCP Enabled. . . . . . . . . . . : No
Autoconfiguration Enabled . . . . : Yes
Tunnel adapter Local Area Connection* 31:
Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : Microsoft 6to4 Adapter #23
Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0
DHCP Enabled. . . . . . . . . . . : No
Autoconfiguration Enabled . . . . : Yes
Tunnel adapter Local Area Connection* 33:
Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : Microsoft 6to4 Adapter #24
Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0
DHCP Enabled. . . . . . . . . . . : No
Autoconfiguration Enabled . . . . : Yes
Tunnel adapter Local Area Connection* 34:
Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : Microsoft 6to4 Adapter #25
Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0
DHCP Enabled. . . . . . . . . . . : No
Autoconfiguration Enabled . . . . : Yes
Tunnel adapter Local Area Connection* 36:
Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : Microsoft 6to4 Adapter #27
Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0
DHCP Enabled. . . . . . . . . . . : No
Autoconfiguration Enabled . . . . : Yes
Tunnel adapter Local Area Connection* 37:
Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : Microsoft 6to4 Adapter #28
Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0
DHCP Enabled. . . . . . . . . . . : No
Autoconfiguration Enabled . . . . : Yes
Tunnel adapter Local Area Connection* 35:
Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : Microsoft 6to4 Adapter #26
Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0
DHCP Enabled. . . . . . . . . . . : No
Autoconfiguration Enabled . . . . : Yes
Tunnel adapter Local Area Connection* 38:
Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : Microsoft 6to4 Adapter #29
Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0
DHCP Enabled. . . . . . . . . . . : No
Autoconfiguration Enabled . . . . : Yes
Tunnel adapter Local Area Connection* 40:
Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : Microsoft 6to4 Adapter #31
Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0
DHCP Enabled. . . . . . . . . . . : No
Autoconfiguration Enabled . . . . : Yes
Tunnel adapter Local Area Connection* 45:
Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : Microsoft 6to4 Adapter #33
Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0
DHCP Enabled. . . . . . . . . . . : No
Autoconfiguration Enabled . . . . : Yes
Tunnel adapter Local Area Connection* 43:
Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : Microsoft 6to4 Adapter #32
Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0
DHCP Enabled. . . . . . . . . . . : No
Autoconfiguration Enabled . . . . : Yes
Tunnel adapter Local Area Connection* 50:
Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : Microsoft 6to4 Adapter #35
Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0
DHCP Enabled. . . . . . . . . . . : No
Autoconfiguration Enabled . . . . : Yes
Tunnel adapter Local Area Connection* 52:
Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : Microsoft 6to4 Adapter #36
Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0
DHCP Enabled. . . . . . . . . . . : No
Autoconfiguration Enabled . . . . : Yes
Tunnel adapter Local Area Connection* 53:
Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : Microsoft 6to4 Adapter #37
Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0
DHCP Enabled. . . . . . . . . . . : No
Autoconfiguration Enabled . . . . : Yes
Tunnel adapter Local Area Connection* 56:
Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : Microsoft 6to4 Adapter #38
Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0
DHCP Enabled. . . . . . . . . . . : No
Autoconfiguration Enabled . . . . : Yes
Tunnel adapter Local Area Connection* 58:
Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : Microsoft 6to4 Adapter #40
Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0
DHCP Enabled. . . . . . . . . . . : No
Autoconfiguration Enabled . . . . : Yes
Tunnel adapter Local Area Connection* 57:
Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : Microsoft 6to4 Adapter #39
Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0
DHCP Enabled. . . . . . . . . . . : No
Autoconfiguration Enabled . . . . : Yes
Tunnel adapter Local Area Connection* 70:
Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : Teredo Tunneling Pseudo-Interface
Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0
DHCP Enabled. . . . . . . . . . . : No
Autoconfiguration Enabled . . . . : Yes
Tunnel adapter isatap.{F464A3E5-95B3-4E00-8B1C-4FAD657B1EF9}:
Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : Microsoft ISATAP Adapter #2
Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0
DHCP Enabled. . . . . . . . . . . : No
Autoconfiguration Enabled . . . . : Yes
Tunnel adapter isatap.{68D1DDD2-DEE1-44CF-B523-24A567A2CF67}:
Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : Microsoft ISATAP Adapter #3
Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0
DHCP Enabled. . . . . . . . . . . : No
Autoconfiguration Enabled . . . . : Yes
Tunnel adapter isatap.{42861E73-8E24-482C-9E93-BE2B94966E48}:
Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : Microsoft ISATAP Adapter #4
Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0
DHCP Enabled. . . . . . . . . . . : No
Autoconfiguration Enabled . . . . : Yes
C:\Users\apagtalunan> -
I have a windows 8 computer. I can't connect my Ipad to Itunes wirelessly when my computer is a wired connection. I have to disconnect my ethernet cable from the computer and connect as a wifi connection.Then the Ipad shows up in Itunes.Any sugestions?
I'd start with the following user tip:
iTunes for Windows 10.7.0.21: "iTunes has stopped working" error messages when playing videos, video podcasts, movies and TV shows
Maybe you are looking for
-
Check numbers for individual invoices in PAYR
Hey Folks: I have 5 invoices cleared against one ZP document ( clearing document) with payment method being check. I could not find the check information for the invoice line items which got cleared against ZP document in PAYR table. Would someone gi
-
Essbase Dimension Order in a Fix Statement
Does the dimension order (sparse and dense) make a difference in an Essbase Fix statement? I would appreciate any thoughts. Thanks!
-
Non-blocking file behaviour for Reader
Hi! It will be really nice if Reader will not block files for writing. Assume someone is using TeX to create PDF and he need to a) examine the results; b) edit the source. It becomes a nightmare with Reader. Compile TeX, open Reader, examine results,
-
Keep getting 'error -1309' trying to transfer file---getting desperate
Trying to deliver a .avi from edited show to a client so they can load on to their server for play back. Hopefully not the problem except been trying to get it to them for the last 2 days and cannot get this to work. MUST have for them by 7am tomorro
-
How do I acess the music in my itunes library? Since installing icloud I can't see any of my music or access it and it's really stressing me out! Help!