TS1470 hi i have an iphone 4s i did an update to ios 7 , after few days i got message to update it againe to 7.0.2 but i got a message to connect my iphone to the itune.and in my computer i got a message the iphone could not be restored error occurred 29

hi i have an iphone 4s i did an update to ios 7 , after few days i got message to update it againe to 7.0.2 but i got a message to connect my iphone to the itune.and in my computer i got a message the iphone could not be restored error occurred 29

l3az wrote:
... got a message the iphone could not be restored error occurred 29
Error 20, 21, 23, 26, 28, 29, 34, 36, 37, 40
These errors typically occur when security software interferes with the restore and update process. Use the steps to troubleshoot security software issues to resolve this issue. In rare cases, these errors may be a hardware issue. If the errors persist on another computer, the device may need service.
Also, check your hosts file to verify that it's not blocking iTunes from communicating with the update server. See the steps under the heading "Blocked by configuration (Mac OS X / Windows) > Rebuild network information > Mac OS X > The hosts file may also be blocking the iTunes Store." If you have software used to perform unauthorized modifications to the iOS device, uninstall this software prior to editing the hosts file to prevent that software from automatically modifying the hosts file again on restart

Similar Messages

  • TS3694 My Ipod could not be restored error occured (3014) have tried all of the above?

    My itunes will not recognise my Idop Touch, I asks me to restore it when I do I get error message ipod could not be restored and unknown error occured (3014) have been on trouble shooting web site have done all they have said but no luck!

    Have you looked at the previous discussions listed on the right side of this page under the heading "More Like This"?

  • TS3694 I forgot my passcode, then I decided to restore through Itune but it says iphone 3 could not be restored error 1015 occurred. what should I do?

    I forgot my passcode, then I decided to restore through Itune but it says iphone 3 could not be restored error 1015 occurred. what should I do?  

    Was the computer used to jailbreak a different iOS device? Are you trying to forcibly install a version of iOS other than the current version for your device? (4.2.1 for the 3G, 6.0.1 for the 4 and 4S, 6.0.2 for the 5).
    Those are the only other reasons you would get that error other than an extremely rare hardware failure.

  • I have swtiched to Lion and now my backup to Airport is not working. Error - The backup disk image "/Volumes/Data/Anik Karimjee's MacBook Air.sparsebundle" could not be accessed (error -1).

    Hi
    I have a time capsule that has been working fine, but I swtiched to Lion and now get this error with no help?
    The backup disk image “/Volumes/Data/Anik Karimjee’s MacBook Air.sparsebundle” could not be accessed (error -1).

    See # C17 in Pondini's excellent support document Time Machine -- Troubleshooting
    http://pondini.org/TM/Troubleshooting.html

  • Failed iOS7 update -- then iPhone could not be restored error 27

    Hello community
    I tried to upgrade t0 iOS7 on my iphone4s via USB itunes connection. It finished downloading and then error box came up saying "iphone could not be updated
    '. then the phone was stuck on apple logo and i reset the phone and now its in recovery mode. itunes tell me to restore my phone but error box keeps on popping up with "iphone could not be restored error 27". tried everything...reinstalled itunes, disabled firewall/security and nothing's working =((((
    HALLP

    Hi.
    Ipad 3 wifi a1314 here failed while upgrading to ios 7 over wifi. After that, it is stucked on recovery mode. Itunes is latest 11.1.3 and firewall my pc is off, antivirus off and I keep on getting error 27
    What does this error mean?
    Restoring ipad software bar on itunes compleates
    verifying ipad software compleates
    but fails verifying ipad restore on error message The ipad "iPad" could not be retsored. An unknown error occurred (27)
    The status bar on the IPad device (under the logo) stucks on about 85%
    The local Ipad service that was supposed to be applec certified simply did the same and said cannot fix withough no explanation what is worng with the device.
    I am a bit dissapointed because the device is 1,5 years old only.

  • HT2953 i-tunes could not be used because the original file could not be found.could not locate.this error occurs on most of my songs in my library and will not play even though they are in my i-pod and play with no trouble.can  anyone please help?

    i-tunes could not be used because the original file could not be found.could not locate.this error occurs on most of my songs in my library and will not play even though they are in my i-pod and play with no trouble.can  anyone please help?

    I was not complete clear.
    Since you never changed the settings in the advanced section of iTunes preferecnes, you have to chech that your music is really in the location setted in the folders reported in the advanced section.  If not you have 2 ways: reset the position of this folders or in the actual disk organisation or in the pointing on the preferences.
    If you press the reset button you just give to itunes its default setting as for the position of the music files: probably this will be a good choice if you have never changed any default preference.
    But before I would check the folders and see if the songs are really there
    In my iTune I have this, and I believe it is the default.
    Users/YOURHOMEFOLDERNAME/Music/iTunes/iTunes Music

  • HT201210 Iphone could not be restored error (1604).

    I updating ios6 but i can't itunes shown Iphone could not be restored error (1604) and i can't open the device.

    It also happened to me. What I did was to put my USB connector at the back of my PC (the main USB port) then I open my iTunes again and Viola, it solves my problem.

  • HT201210 iphone could not be restored error no 1015

    iphone could not be restored error no 1015
    massege recieved while updating
    mobile could not start

    Search!!!!!!
    http://lmgtfy.com/?q=iphone+error+1015

  • Even after resets get "The backup disk image "/Volumes/FreeAgent GoFlex Drive/MacBeth (2) 1.sparsebundle" could not be created (error 22)."

    HELP!  "The backup disk image “/Volumes/FreeAgent GoFlex Drive/MacBeth (2) 1.sparsebundle” could not be created (error 22)."
    TC estimates over 750GB for full backup.
    Late 2010 MBA is connected wirelessly to
    802.11n (1st gen) TC that is connected via ethernet hub built into house to motorola router using charter.com for internet.
    I have had same problem for over 150 days and multiple reboots, restarts in proper order, firmware updates, unplugs with 5min plus gaps, bypassing the tc and using external 500gb WD mybook via usb to time capsule, replacement of the WD mybook to new 2TB Free Agent GoFlex drive, etc, etc, etc!  Note: I originally named my MBA hard drive MacBeth, but at some point months ago, it said backup already existed and system automatically created MacBeth (2), worked for a while, then stopped again, despite trying nearly daily.
    I gave up and started using Carbon Copy Clone daily for just the 128gb on internal SSD of my late 2011 11" MacBook Air, but need to get past these time capsule errors to back up the external disk!  Due to lack of space in MBA, I had long ago transferred both itunes and iphoto and all imovie/fcpx files to a 1tb external disk (WD Passport) that I keep in my bag with MBA.  It is partitioned with 150gb for cloning the MBA, and over 750gb for media/itunes/iphoto/etc.
    Also, I have endured months of "your hard drive is full" messages and system lockups, applying the solution given to me by genious bar (deleting all aol.com outboxes/recovered messages/spam/trash under library/mail/V2/Mailboxes folders, empty trash, restart....watch recovered hard drive space mysteriously shrink next couple days to zero.....repeat)
    Due to lack of space, I had not been able to do javascript and other system updates.  Yesterday, I noticed even safari bookmark bar had mysteriously emptied (not disappeared, I can hide and show the space where the bar used to be - it is just blank area with no data except for eyelass-book-topsites icons), so I transferred a few large quicktime movie files recorded with isight camera to the external disk, and freed up 20 gbs for the first time!
    This got my hopes up yesterday because after I completed all system/software updates, suddenly the bookmark bar showed up and I was able to start the time capsule backup! It took overnight preparing for backup, but finally started and progressed to 12gb of the 100gb+ needed (i guess the update where it left off months ago for the estimated 750gb for the full backup?), then I put system to sleep and took it with me (thus leaving the wireless time capsule network as I do daily fully expecting it to continue when I returned home in the evening.)  But alas, upon return, back to the "Time Machine could not complete backup, The backup disk image ".....sparsebundle" could not be created (error 22)"  Ugh!  More reboots, unplugs, 5min gaps....still Ugh!
    So the problem continues...please help!  Here are my settings:
    About this mac:
    Mac OS X V. 10.7.5
    processor 1.6 ghz intel core 2 duo, memory 4 4g 1067 MHz DDR3
    software up to date!
    Airport Utility:
    V 6.2 (620.33)
    both internet globe and TC show green dots in graphic, however internet occasionally shows yellow then goes to green, but still gets error 22.  Suddenly TC showed explanation mark and says lost connection and asked if I wanted to 'forget', gave same errors, then mysteriously went back to green, but still got error 22!.
    Internet:
    connection: connected, displays router address, 2 dns server, and domain name: charter.com
    Time Capsule:
    shows network, ip address, serial number, version 7.6.3, status: (green dot) Setup over WAN,
    wireless clients: phones, macbooks (including this MBA), printers, wii
    If you need other settings to help me, just ask!  I have read a few of the other solutions in forums, but trying not to erase disks, especially since it worked for a minute yesterday!

    To step sideways.. why not just use CCC to backup the 750GB of the hard disk to the TC.
    You need to understand this is going to be a super slow process and each time you stop it.. it is going to give issues. CCC will at least do a more reliable job of it than TM.
    I would also say.. this is going to be tough without ethernet. You need to understand the backup speed over wireless can be 10GB per hour.. that makes 75hrs to backup the disk. The air needs to run non-stop doing that.. without you touching it.
    I would get another external drive.. plug that into the MBA and if you really want to use TM.. make a backup one to the other.. but CCC will again do a better job and work faster. It will be much faster than over wireless.
    I am trying to think of ways around the issue of just speed.. but plainly you have lots of other issues.. being the simple unreliablity of the TM to identify the TC.
    If you want to make this work.. give yourself a weekend.
    Load 5.6 utility into the MBA..
    http://support.apple.com/kb/DL1482
    Take the TC back to 7.5.2 firmware. It is a really old version and latest firmware does it no good at all.
    Wipe its hard disk using erase and start over.. give it new names for everything.
    So call it TC
    Set the wireless to 5ghz and name it TC5ghz
    Use WPA2 Personal security. Use a 10 character passkey non dictionary.
    At 5ghz you should get 2x the speed as at 2.4ghz but the air will need to be right next to the TC..
    (alternatively buy the USB to ethernet cord apple have available.. it is $30 in the apple store and do it over pseudoethernet. http://store.apple.com/au/product/MC704ZM/A/apple-usb-ethernet-adapter That is the wrong store but you get the idea. )
    WIth a fully clean system.. now do a full reset of TM.
    See A4 http://pondini.org/TM/Troubleshooting.html
    Direct the TM to back to the TC.. and make sure the external hard disk is not excluded.
    Of course the TC has to be 1TB version to fit that much data.. goes without saying right.
    Even over pseudo - ethernet this will take many hours.. and you basically have to leave it to work.. do not touch it.. make sure the MBA cannot sleep though.. turn off sleep.. beforehand.

  • IOS6 installation completes thru restoring firmware when one of two messages come up on iTunes screen:  could not find device, or could not be restored error -1.  Rep. at AT

    Down loaded iOS6 on iPhone 4S. When complete, screen showed usb cable end with arrow to iTunes logo.  Brought up iTunes on computer screen.  OS Windows XP, computer on wi-fi.  After connecting phone to computer, ITunes screen showed name: Phone, capacity: n/a, software version n/a, serial no: n/a.  Under Version, check for update: Your iPhone software is up to date.  Serial no., etc. had previously appeared on iTunes screen in the the past before I attempted the iOS6 download.  Clicked on restore.  ITunes showed extracting software.  Message came up, could not be restored, error 1656.  Took computer and phone AT&T.  Rep contacted Apple Support - as directed rep reinstalled iTunes.  Clicked on restore again, went through extracting software, then into loading software - loading bar showed on iTunes screen and phone screen.  Was almost complete when message came up on computer - device could not be found.  By then ATT store closed.  Tried to restore at home.  Got as far as as restoring firmware, phone screen was showing loading on bar.  Message came up - could not be restored, error -1.    ATT rep said several other customers contacted him with the same problem.    Nearest Apple store to me is 95 mi. away.  Any on line help would be greatly appreciated.  Thank you.

    Additional comment from Carl 37: Phone is locked up with screen showing usb cable end with arrow to iTunes logo.  What can I do to regain use of phone?

  • When backing up on time machine is get " The back up disk image'/volume/data/eric balnchard's Macbook.sparbundle"could not be accessed (error-1). what does it mean? it's a new time machine

    when backing up on time machine is get " The back up disk image'/volume/data/eric balnchard's Macbook.sparbundle"could not be accessed (error-1). what does it mean? it's a new time machine

    Expect to see this error again due to a bug in Lion (and Mountain Lion).
    See # C17 in Pondini's excellent support document below, or look over to the right of this web page under the heading of More Like This
    http://pondini.org/TM/Troubleshooting.html

  • HT3275 TIME MACHINE ERROR: The backup disk image "/Volumes/Data/Sean McGuire's MacBook Pro.sparsebundle" could not be created (error 1).

    I can select a disk (Time Capsule) and initiate the backup.  It only "waits to back up" then "making backup disk available" and remains frozen there.  I tried to update the software a while back and was unsuccessful, I think that may be the issue.
    Any insight would be greatly appreciated.  This is the error message I receive.
    TIME MACHINE ERROR: The backup disk image “/Volumes/Data/Sean McGuire’s MacBook Pro.sparsebundle” could not be created (error 1).
    Thanks

    See #C17 in Pondini's excellent support document Time Machine - Troubleshooting
    http://pondini.org/TM/Troubleshooting.html

  • HT3275 I continually get this message: The TM could not complete backup.  The backup image "/Volumes/Data/....'s computer_001ec21b890f.sparsebundle" could not be accessed (error 1).?

    I continually get this message: The TM could not complete backup.  The backup image "/Volumes/Data/....'s computer_001ec21b890f.sparsebundle" could not be accessed (error 1).?

    Have you looked through Pondini's extensive TM help site?
    http://Pondini.org/TM/FAQ.html
    http://pondini.org/TM/Troubleshooting.html
    Can't imaging something not being covered there.

  • The iphone could not be restored error 23

    **Hello to all I have a iPhone 3gs 3.1.3 Suddenly went Network and i Switched off the devices and turn it on again prepared But not open network and mark appears cable & iTunes And worked restor but an error message appears the iphone could not be restored 23 .**
    **The iPhone still does not function with the flag whenever two devices the same problem .**
    **Please help**
    *thankss*

    Error 23 is generally a hardware failure. If under warranty, make an appointment at an Apple store or contact whoever handles warranty & support where you live. If out of warranty, google third party repair shops in your area. You will not be able to restore with a hardware failure. To confirm, try restoring on a known good computer, if you get the same error message, you have a hardware failure.

  • The iPod could not be restored - error code 1433

    Just today I went to sync my 4th generation 20GB iPod with my Mac and iTunes gave me the following error message:
    "iTunes has detected an iPod that appears to be corrupted. You may need to restore this iPod before it can be used with iTunes. You may also try disconnected and reconnecting the iPod."
    I tried disconnecting and reconnecting several times, but always got the same error. I then tried to restore the iPod. iTunes then hung for several minutes before presenting another dialog box with the following error message:
    "The iPod "iPod" could not be restored. An unknown error occurred (1433)."
    Upon clicking the More Information button I was directed to the following web page:
    http://support.apple.com/kb/TS1372
    I've tried restarting the computer and connecting the iPod to a different USB port. The windows suggestions would seem not to apply. I read somewhere else on these forums that the error code was previously triggered when people tried to update older iPods with the then-new iTunes 7.6. Is it possible that iTunes is unable to restore an iPod as old as mine?

    From my experience it can be either an iPod or computer problem, try to prove it by doing a restore with another computer, if it works then you need to deal with the computer.
    In my case, I finally found out it was the bad USB hub causing the problem ... don't use the hub without the external power

Maybe you are looking for

  • Main Reports' Group Tree doesn't retain last record selected

    In Crystal 2008 Viewer, when you click one of the last tree nodes on a long Group Tree, the program jumps to that part of the report for that group.  But when you return to the Main report tab the Group Tree pane returns to the top. According to my u

  • How to change the font size from tabs ???

    Hi I found a tip to change the CSS in the apache directory in the forum here. but i can´t find the directory on my hard disk/oracle directory i got this version installed: Oracle Database 10g Express Edition Release 10.2.0.1.0 - Product PL/SQL Releas

  • Whats wrong with port

    hello i have made simple video player http://83.149.241.81/chto/chtoPlayerTest/CHTOPlayer.html it plays fms's streams (vod) But customer cannot use it, he opens "log" (inside player), and log stops in line "FMS connecting to rtmp://83.149.241.81/vod"

  • How can I have two differents versions of provider working in a Server

    Hi... I'm a ASP Classic developer. I'm working with Oracle 10g and I'm using the Oracle Provider 10.1 but now I need to change of version to 10.2 Release. So I install the 10.2 Release Version in same host where I have de 10.1 version. For do the con

  • Design Projects

    Hello All, I'm a student doing a 'Advanced VLSI design' class, I'm looking for a design project. I came to know recently about open-sourced SPARC processor core. Are there any possible projects, in which we can contribute in terms of the Design/Layou