TS3694 Hi,I have an iphone 3g that is "not" jailbroken,nor have I tried,however,I had been having problems with it shuting down¬ starting again so I updated&tried to restore only to have an error 1015.The iphone is now stuck on the connect to itunes,pl
Hi, I have an Iphone 3g that is "Not" jailbroken, nor do I want it to be jailbroken. However, I had been having problems with it shuting down and not starting again. So, I tried to update and restore only to get an "error" 1015.
It is now stuck on "connect to itunes"
Any help would be great as this is a factory unlocked phone
Apple in no way blocks devices.
Carriers can blacklist devices from their network. If that is what has occurred, only the carrier can remove the blacklist. This should have nothing to do with your ability to activate the device and use it as an iPod.
Similar Messages
-
After sorting the material of my friends on the drive and creating a new user, I realized that the system was unusable with 30 or 40 crashes a day. I am a photoshop user and my friend had installed cs2 and upgraded to cs5. Actually everything was crashing and he had had the problems in Lion and they did not go away in Mountain Lion.
So my sense is the next best step is to uninstall and reinstall the operating system....but I'm entirely new to Mac though I quite good at problem solving on PC. I have been messing around trying to get Mac up for over a week now so am learning quickly but feel uncertain about the steps in installation and don't want to mess things further.
I have found this
https://discussions.apple.com/docs/DOC-3351
which seems useful.
I'm backing everything now to a usb drive, I have one copy in timemachine, but I need a clean install so I'm backing things manually as it's not so complicated my being a new user.
I have the original discs of Snow Leopard and a dmg file of Mountain Lion that were installed on this computer.
I hope I can find my friends Adobe id and password.....he does have a list of passwords, how can I check if they are correct.
Do I need to install Snow leopard from the original disks first and then update and then upgrade to Mountain Lion?
He upgraded first to Lion but I can't find that program to install, do I need it to get to Mountain Lion?
I don't have boot disks, does that matter?
What can I do about CS5 in a restore? I don't mind loosing other programs so much as this one.....I haven't seen the upgrades and only have CS2. What happens to all your programs...I guess they are just lost?
I haven't used mail, so I'm not worried about that.
Hope I can get some support with the process, any support will be valued that is at all related. Thank youMerielsea wrote:
I am looking through this material, it's great. I'm wondering though, does command r work in #8 if my original disks where Snow Leopard?
Yes, when the operating system was upgraded to 10.7 then to 10.8, it 10.6 was replaced so those 10.6 disks are only good now for completely erasing the entire drive and reverting the machine back to 10.6
10.7 and 10.8 has a Recovery HD partiton on the boot drive.
https://support.apple.com/kb/HT4718
I have a mountain lion dmg file that was used to upgrade from Lion, would double clicking on this equal the same thing as reinstalling mountain lion over itself?
I wouldn't use this, as Apple is now changing things, so you need to reinstall 10.8 via the Recovery HD
I would prefer to keep CS5 photoshop
Not going to happen, if it's working now good for you. But according to Roaring Apps it's not working for 10.8. and it needs to be upgraded to CS6
If you revert the machine to 10.6 or 10.7, your going to erase CS5 and everything else.
Doing #20 would be a bit beyond me and I don't know another mac user so that I can work from their mac.
Why do you need another Mac users machine?
Print out the instructions.
Here is some more about secure erasing for a new owner
How do I securely delete data from the machine?
Installing OS X 10.8 again
https://support.apple.com/kb/HT4718
Does the reinstall have to go from Snow Leopard which was the base install, to lion then to mountain lion,
No, you erase and install 10.8
When Apple upgrades 10.6 to 10.7 then to 10.8, it's a complete operating system replacement, it's called a upgrade because it's still OS X but leaves all your files and most programs intact, none of the older operating system version remains.
Just like if you would upgrade Vista to Windows 7, or Windows 7 to Windows 7 Pro.
Can I install the mountain lion upgrade over a freshly installed Snow Leopard?
Yes, but it requires erasing the entire drive (including 10.8 Recovery HD) from the 10.6 disks, then installing 10.6, then Software Updating to 10.6.8, then buying 10.8 from the AppStore, then downloading it and installing it, then the machine will be 10.8
Or you can use the Recovery HD and just erase the Macintosh HD parittion then reinstall 10.8 that way for free.
How to reinstall just OS X or erase/install OS X
https://support.apple.com/kb/HT4718
See what is confusing you is there is a hidden Recovery HD partition on the boot drive, it can do all the things like a OS X install disk can do, erase the Macintosh HD partiton (where OS X, programs and files are) and install a new copy of OSX from Apple's servers so it reboots to a brand new machine again (no Cs5 though)
Instead of a boot disk, there is a two bootable partitions on the boot drive, one is Recovery HD and the other is Macintosh HD which boots into OS X.
SO your command r booting the operating system in Recovery HD to erase the other partition and reinstall OS X into from Apple's servers, got it.?
Your going to need your AppleID and password to reinstall OS X 10.8, all part of the new world order. -
I'm frustrated, I am doing everything you recommend, I use only two channels, have plenty of memory in my hard disk, and external hard drive, no effects, and still having problems with Garage band. Giving messages as you ave too many live channels, the disk is slow prepare...can you help?
Quote from: Richard on 15-November-07, 20:33:05
tornado2003,
What you need to do is boot into Safe Mode. Then delete the VGA Drivers.
After that boot normally and install the latest nVidia ForceWare Drivers
Take Care,
Richard
i guess you missed that:
Quote from: tornado2003 on 15-November-07, 17:26:52
ive tryed booting xp in safe mode but it just freezes after it loads up a couple of needed files .
ive even formatted my hard drive and tryed installing a fresh xp on it but it just keeps locking up when it gets to the "starting windows setup" .(this is just after it loads all the drivers from the xp cd) -
Has anyone been having problems with camera, safari etc. crashing on iOS 5.0.1 because I have been having the problem as well as my brother I have the iPhone 4. If anyone else having same issue comment below
Then the next step would be a restore as new to rule out corruption in the backup.
-
Q since upgrade to iOS6 l have been having problem with wifi connection and getting into App Store and itunes
Saw this on another post.
Applecare Senior Advisor Txx Bxxx (I have his contact info in an email he just sent) just confirmed with me that the problem people are having with the App Store not loading is an apple issue with there servers, ITS NOT YOUR IPAD so don't go restoring it! It's not happening to everyone however but they are looking into it, its really hit or miss.
In the meantime ...........
The Complete Guide to Using the iTunes Store
http://www.ilounge.com/index.php/articles/comments/the-complete-guide-to-using-t he-itunes-store/
Can't connect to the iTunes Store
http://support.apple.com/kb/TS1368
iTunes: Advanced iTunes Store troubleshooting
http://support.apple.com/kb/TS3297
Best Fixes for ‘Cannot Connect to iTunes Store’ Errors
http://ipadinsight.com/ipad-tips-tricks/best-fixes-for-cannot-connect-to-itunes- store-errors/
Try this first - Reset the iPad by holding down on the sleep and home buttons at the same time for about 10-15 seconds until the Apple Logo appears - ignore the red slider - let go of the buttons.
This works for some users. Not sure why.
Go to Settings>General>Date and Time> Set Automatically>Off. Set the date ahead by about a year.Then see if you can connect to the store.
~~~~~~~~~~~~~~~~
iOS 6 Wifi Problems/Fixes
Fix For iOS 6 WiFi Problems?
http://tabletcrunch.com/2012/09/27/fix-ios-6-wifi-problems/
Did iOS 6 Screw Your Wi-Fi? Here’s How to Fix It
http://gizmodo.com/5944761/does-ios-6-have-a-wi+fi-bug
How To Fix Wi-Fi Connectivity Issue After Upgrading To iOS 6
http://www.iphonehacks.com/2012/09/fix-wi-fi-connectivity-issue-after-upgrading- to-ios-6.html
iOS 6 iPad 3 wi-fi "connection fix" for netgear router
http://www.youtube.com/watch?v=XsWS4ha-dn0
Apple's iOS 6 Wi-Fi problems
http://www.zdnet.com/apples-ios-6-wi-fi-problems-linger-on-7000004799/
~~~~~~~~~~~~~~~~~~~~~~~
Look at iOS Troubleshooting Wi-Fi networks and connections http://support.apple.com/kb/TS1398
iPad: Issues connecting to Wi-Fi networks http://support.apple.com/kb/ts3304
WiFi Connecting/Troubleshooting
http://www.apple.com/support/ipad/wifi/
How to Fix: My iPad Won't Connect to WiFi
http://ipad.about.com/od/iPad_Troubleshooting/ss/How-To-Fix-My-Ipad-Wont-Connect -To-Wi-Fi.htm
iOS: Connecting to the Internet
http://support.apple.com/kb/HT1695
iOS: Recommended settings for Wi-Fi routers and access points http://support.apple.com/kb/HT4199
Additional things to try.
Try this first. Turn Off your iPad. Then turn Off (disconnect power cord for 30 seconds or longer) the wireless router & then back On. Now boot your iPad. Hopefully it will see the WiFi.
Go to Settings>Wi-Fi and turn Off. Then while at Settings>Wi-Fi, turn back On and chose a Network.
Change the channel on your wireless router (Auto or Channel 6 is best). Instructions at http://macintoshhowto.com/advanced/how-to-get-a-good-range-on-your-wireless-netw ork.html
Another thing to try - Go into your router security settings and change from WEP to WPA with AES.
How to Quickly Fix iPad 3 Wi-Fi Reception Problems
http://osxdaily.com/2012/03/21/fix-new-ipad-3-wi-fi-reception-problems/
If none of the above suggestions work, look at this link.
iPad Wi-Fi Problems: Comprehensive List of Fixes
http://appletoolbox.com/2010/04/ipad-wi-fi-problems-comprehensive-list-of-fixes/
Fix iPad Wifi Connection and Signal Issues http://www.youtube.com/watch?v=uwWtIG5jUxE
Fix Slow WiFi Issue https://discussions.apple.com/thread/2398063?start=60&tstart=0
Unable to Connect After iOS Update - saw this solution on another post.
https://discussions.apple.com/thread/4010130
Note - When troubleshooting wifi connection problems, don't hold your iPad by hand. There have been a few reports that holding the iPad by hand, seems to attenuate the wifi signal.
~~~~~~~~~~~~~~~
If any of the above solutions work, please post back what solved your problem. It will help others with the same problem.
Cheers, Tom -
I have been having problems with my iPod touch and my WRT...
I have been having problems with my iPod touch and my WRT54G router. I am so frustrated right now because after following the various steps mentioned in one of these threads, following Earthlink's prompts, and speaking with Apple, my iPod touch will still not work. It is connected to the internet but will not download the pages. It is quite frustrating. I have changed from WPA to WEP, I switched the 4th Generated key to the 1st. I've disabled this, enabled that. I've done just about everything. I updated the firmware. I made the switch from a partial bridge to a full bridge. Still nothing seems to work. Does anyone have any other suggestions? The one thing I have not done is enter the Apple code into the iPod which searches for website...-- I cannot access the internet with my iPod so this web address does not work. If anyone has been successful, will you please give me step by step instructions? Yesterday I was on the phone with Linksys for about an hour. Before that with Apple for about an hour and before that with Earthlink. How it is that I can walk into a Bread Co. or Apple Store and immediately connect to the internet with my iPod but I can't in my own house?? Everyone seems to think it is someone else's problem so I've gone around and around. Not one of the Linksys support personnel suggested I look here on this community forum. I had to pay the $9 fee to have advanced Linksys help but still my iPod does not work and when I called back, the man I spoke with seemed to think the case was closed because my PC, Laptop, and iPod are connected to the internet -- the iPod just won't download the webpages or get mail. My iPod's IP address begins with 192. I would appreciate any help on this matter
Message Edited by AlliW on 10-02-2008 02:06 PMI had the same issues with my iPod touch & iPhone. It's a known issue with the touch & Linksys G routers. Go into settings on the touch & do the following.
1. Settings - wifi - linksys
2. Erase your DNS settings & input same numbers as in router
Settings.
3. Http proxy should be
in off position.
4. Close out & open safari you should now have a wireless
connection. -
I am having problems with my outlook 2011. While i am able to check and SEND email on all my other devices ( Ipad, iphone, Macbook), I am unablesend any email with my iMac ( i can recieve email) . This problem started suddenly and the error message i get is error 5.7.8. I have read the threads on line and went into settings, even created a new profile, nothing helps...Please advice..is this something to do with my keychain Access?
As Outlook is not an Apple product, you will find more helpers familiar with Outlook here:
Office for Mac forums -
I have been having problems with my speaker. After the recent update I am unable to listen to movies, music or apps using my speaker. The volume bar is completely missing. If I plug a headset into the port, the volume bar reappears and then disappears after the headset is removed. This is quite annoying. My child's Apps that he likes to play will not even make a sound. HELP!!!
Do a reset (Hold Sleep/Wake and Home buttons about 10 secs or more till Apple logo appears, ignore the Slide to Power Off that appears)
Note: You will not lose any data. -
I have been having issues with my iCloud email on my iMac. For some time period, everyday, it won't reload and often shows symbols instead of letters for the text. Any ideas how to solve?
All I can suggest is that you open that file on the MBA and save it as a new file, then see if you can open the new one on the iMac.
-
hi, i have a macbook air and i've been having problems with the camera when i'm using skype. i know im no the 1st one and i'd like to know when apple or someone 'll do something about this.
Try reinstalling Combo Update.
http://support.apple.com/kb/DL1676
Best. -
I have just been having problems with my Canon MP250 printer and decided to uninstall and re-install the printer and everytime I try to re-install the printer trough preferences and all I keep getting was a message saying "preparing to queue"...... I then decided to try and reload the Canon printer drivers and for some silly reason I deleted the existing Canon printer drive. Now I cannot load them from the CD provided with the printer or from downloads through the Apple store. If anyone out there could help me I would be greatly appreciated......
These Canon printer/scanner drivers from Apple - http://support.apple.com/kb/DL899 - should work. The MP250 is listed on the support page. Try downloading and installing them.
Good luck,
Clinton -
Have you been having problems with ipod nano 3rd gen?
Have you been having problems with your ipod nano 3rd gen? got a windows xp computer? is your pc not recognizing it? I think i may have the solution. After 2 2 hour calls to apple tech support they were stumped. we reset it again and again, reinstalled itunes again and again. and they had no solution for me. I went to my device managerand there was a device called (apple Ipod USB driver) with a yellow exclamation point. I tried updating driver but to no avail. I tried uninstalling and reinstalling and nothing. But then I had an epiphany. I went to the device manager right clicked the apple ipod usb device clicked properties then update driver. Hardware wizard went up and I chose not to install automatically. and i chose to install driver manually. and then I installed a generic usb mass storage driver in its place and presto!!! it worked! it was instantly recognized by itunes and it took me to the registration page. I did what the apple support team wasn't able to do for 4 hours. I wonder if they're accepting applications... Anyway i hope this helps anyone out there cause i know i went through a lot of stress.
the driver is just a regular usb mass storage driver. it's in your computer. it's just a matter of installing it manually where it saya to include the location of the driver click browse and choose c:\windows\system32
-
Having problems with Bridge shutting down after saving photo in PS Cs5,,,,,,,,, Also when i attempt to update either PS or bridge get an error message in Adobe application manger "Error loading updater workflow"
Sorry for the late reply. My email firewall has become a little over zealous & sent a lot of my emails straight to my junk email folder, so I have only just now discovered your reply in my junk mail folder.
The only "don't open files exceeding xxx megabytes" instruction I can find in my Prefs, is in the Bridge Prefs for Thumbnails, & mine is set at 1000mb. The biggest files I handle are bigger than 200mb so I should be able to open a few, not just one.
However, this doesn't explain why I can open a psd format file of 180mb, close it, but then can't open a RAW format file of only 26mb immediately after.
I can open the RAW file only if I restart my computer - very annoying!
However, thanks for the advice about the video card & memory.
So, I'm still stuck as to what the issue is. -
I have been having issues with my battery capacity. The battery will drain within half an hour with it being fully charged when the battery normally lasts me all day. I haven't had the phone that long so it most definitely shouldn't be happening. I went to my service provider about the problem and he said to go into the apple website, click "support" and then "battery capacity issues" to which you then type in your email to troubleshoot the problem on your phones however, I cannot find this. Someone help me out!
He may have been referring to: https://www.apple.com/support/contact/
On the linked page, click "Get Started" then on the next page click "iPhone" then on the next page "Battery, Power & Charging" then "Battery questions or troubleshooting" -
I have been using FaceTime regularly over the past year or so and suddenly it has stopped working. It seems to dial up and says its connecting and then just switches off. I have a number of other friends who are also having problems with this and also on their iPhones. Does anyone have an answer to this problem?
Make sure all parties are running IOS 7.1.1
http://support.apple.com/kb/TS5419
Maybe you are looking for
-
Upgrade Oracle Forms/Reports from 6i to 11g
Hi you Oracle experts, I'm considering to upgrade my Oracle Forms/Reports application from 6i to 11g. However, I see dozens of separated server components on the download page in OTN. Can anyone guide me what server/developer software components shou
-
Hi everyone, I am trying to get the properties of a button in a webdynpro by doing : IWDButton button = (IWDButton)wdContext.getCurrentElement().getAttributeValue("Go_ctx"); button.setEnabled(false); I get a CastClassException. Can someone help ? Tha
-
Problem running app in default server (Jdev 11g)
Hi, I am pretty new to Java/Jdev and I am facing some problems trying to run the application as laid out in the example tutorial from http://www.oracle.com/technology/products/jdev/11/cuecards/adf_set_22/ccset22_ALL.html. I have followed all the step
-
In SE30, what the graph represents
hi when we analyse the performance of a particular report or BDC using SE30 , we will get a graph. How to analyze that graph. what the graph indicates. how the graph should appear for a better performance report. need the answer more clearly.
-
How to change 5.1 output channels?
I have set the output channels of 5.1 surround in the AUDIO MIDI SETUP to physical outputs 5-10. Soundtrack PRO still uses its own selection/order of 5.1 outputs (ie 1-6). How can I use other outputs of my audio interface? Tnx, Kustav