Ultrabeat multiple out put problem

when i change the output of a voice in ultrabeat it plays out of sync and sounds like a different pattern.When i change it back to "main" its plays back ok.Is it a bug or something?or is something wrong with my system?
Message was edited by: top2004

Hi Vishi
Please check you routine associated with your output type, suppose you have a requiremnt that is qty=5 then trigger DLO1, in such cases every time you save sales order with qty =5 output will trigger automatically.
To avoid such cases add some code in routine that is output has already triggered then don't trigger.
Take help of ABAPer.
try and revert

Similar Messages

Multiple Out put issued

Dear All,
I have one sales order where out put types DLO1, DLO3 and DLO4 are determined as sales order confirmation out put. The transmission medium for all of these is Print out ie external send.
Here in the sales order multiple out puts are issued. Customer has received 5-6 mails for each output. When i go to out put determination / edit screen thre also i can see as many number of lines partaining to output types.
Can you please help me solving this issue since i am not able to analyse from where or how this thing is happening.
One imp thing i noted that all the out put are automatically detemined. I mean no mannual addtion of lines has happened.
Regards,
Vishi.

Hi Vishi
Please check you routine associated with your output type, suppose you have a requiremnt that is qty=5 then trigger DLO1, in such cases every time you save sales order with qty =5 output will trigger automatically.
To avoid such cases add some code in routine that is output has already triggered then don't trigger.
Take help of ABAPer.
try and revert

Billing out put problem

hi gurus,
I have a problem when creating billing out put automatically. through condition technique . I did it when am looking into vf02 it is not coming automatically. when am giving manually it is accepting. when i saved that out put type it is saving and green singl is coming. But it is not coming automatically. Even though i maintained conditon records in vv31. still am getting this prob. in procedure. am having conditon type that
conditon type i assigned i proce.
If any one know this please help.me . he will get maximum rewards from this query.

Hi Nag,
I.Once again check assignments with repect to billing type.
2.Check the communication tab in VV32 are you maintaining all parameters or not,check the storage field it should be filled with print,check medium also.
I hope it will help you
Regards,
Murali.

XML PUBLISHER report in Excel out put problem

Hi Experts,
I have developed one XML report which output type is EXCEL in Oracle Application.
I am getting some -ve value in the report so I need to do the trailing sign
Menace for example I got a value -8645 I need to display the value like (8645).
This functionality is working in PDF output but in EXCEL out put it is not working.
Could any body please help me on this..
Its Urgent .
Thanks in Advance.

Check this metalink notes, did you got any error..?
Note: 364547.1 - Troubleshooting Oracle XML Publisher For The Oracle E-Business Suite
https://metalink.oracle.com/metalink/plsql/ml2_documents.showDocument?p_database_id=NOT&p_id=364547.1
Note: 359875.1 - Cannot View Xml Publisher Report Output In Excel Format
Note: 358296.1 - How To Produce Requests In Formats Of HTML, RTF, and Excel From XML Publisher
Note: 850685.1 - Wrong Output Format In Xml Publisher Output
Note: 727031.1 - XML Publisher Requests Always Get Defaulted to Output Format as PDF Whatever the Template Type is Set To
Note: 337343.1 - Unable to View Excel Output File Created by XML Publisher
Note: 401328.1 - Default Layout Format for XML Publisher Concurrent Request Is Always PDF
Re: XML Publisher Server on EBS 11.5.10.2

Report web out put problem

Hi:
I used 10g forms and reports for my application. When I run a report .rdf file in form used
web.show_document(v_parameter_string ,'_blank');
build in function, the v_parameter_string include all parameter for server and application.
Everything is ok and the report file appears in the browser window. But maybe the size of each row is too long, the words in the report body with font size =1 -- the smallest size of letter. So the color of words in report body part is dark gray but the title part is normal black color (words' font size is 2 or upper). This make I looking at report body very difficult in web browser. When I print the report from browser, the print out paper is good and no color different between body and title part.
Do some people know why this gray color issue happened and how to fix it making the black color words appear in the report body.
Thanks.
LWU

Hi Madhu,
Yes, I did but out put is not coming.
Regards,
Pradeep Krishnamurthy

Out put problem in Ad hoc query reports

Hi Gurus,
I am tryting to generate a report through Ad hoc query in S_PH0_48000510 - Ad Hoc Query SAP/Query/HR_ADM - > Selected several options like personnel number / employee name / entry date / leaving date.
But when we select it shows the input details but when i try for output the entry date / leaving date even the names of the employees are not reflecting.
But the age/date of birth other fields are coming in output.
Kindly let me know the solution to get a out put. If there is any changes need to be done in the back end. Pls advice with the path details.
Thanks & Regards,
Pradeep Krishnamurthy

Hi Madhu,
Yes, I did but out put is not coming.
Regards,
Pradeep Krishnamurthy

Csv report out put problem

am trying to generate delimited format report on command prompt.
out put is to huge and it gives error . To over come this when I turned page break to yes the report will be generated successfully but the out put number of rows are being doubled.
suppose initially I am getting 100 rows , With page break set to yes the out put in
report csv format will be 200

Its not possible to export data directly from 6i to excel but you can export in text file and then open it in excel it will open very easily but keep it in you mind first eliminate all report groups.
and
There is a trick to capture Oracle Reports output (text output) into a excel sheet.
Basic Steps :
1) Set the output format for the report to XML
2) Run the report to generate output.
3) Save the output file locally as a XML file.
4) Open the file using MS Excel.
5) To make it more beautiful, you may use a MS Excel Template
and read below may be this will be helpful to u
http://kr.forums.oracle.com/forums/thread.jspa?threadID=853876
Reports 6i Matrix Output in Excel Format

Ultrabeat + Multiple Outs - Sorted!!

Hello Peeps, just a note to say that I've cracked the problem with Multiple Outputs and Ultrabeat (Logic Pro) - set up as normal and then trigger notes from the MIDI keyboard, from there on it's fine. Thanx for all the help, cheers, Rich C.

Hi,
1. Instantiate a multi-ouput EXS24 instance. NOT a Stereo version.
2. Create new auxes according to how many outputs you will need.
3. In each Aux, select the exs output you want to feed to that Aux track.
4. In the EXS, for each track, change the output that you want to route the track to.
Voila.
Cheers.

Out Put Problems After Crash

Hi I am running a newly installed LP8 following a crash to day I am having problems getting sound out
If if I switch core audio to Built in Audio I do get sound from my internal speaker.
I am Running a MOTU traveller and a MOTU 828 which are linked in Core audio and clocks linked by fiber .If I switch core audio to Both together or the Traveller on its own( I use the Traveller’s channels 1 and 2 to input to my monitors) I get I high pitched beeping sound which seems to lag the playing of my midi Keyboard
I have tried various adjustments but to be honest I am just poking an hoping
Any ideas?

Sounds like you're already running an aggregate audio audio setup (linked in core audio). Maybe the crash wiped out the arregate device?
Often resetting the MOTU 828 can clear up "beeping" sounds.
Is it and 828MkII?
If so the reset procedure is:
- Unplug the firewire
- press the button "setup", turn full right until "factory default"
- push select
- confirm with "value"
- plug back firewire
Might want to check the manual and see if the Traveler has
a reset procedure as well.
If none of the above just make sure your audio clocks are locked at the same frequency. Also, shut the Mac down, unplug all of the MOTU stuff, boot the Mac, plugin the MOTU units.
pancenter-

Data load and out put problem

Hi Experts,
Iam going through a peculiar problem.I have data flowing from R/3 to master data Info provider 0Requi. I have validated the data between R/3 and the master data info provider, it is found to be good. This data is being loaded from 0Requi to a staging write optimized DSO. there are routines in the Transformations for the DSO. when I check and compare the data, I found that out of 625 records in the Source only 599 were available in the target, and out of 599 records 17 records are duplicate and 29 records have not been populated from source to target.
Any help to solve the issue will be highly appreciated and thanked with suitable points.
Thanks and Regards
SHL

Thank you very much Jen, Full points to you.
There was nothing in the error stack. Sy_Subrc in the routine was giving the problem. It has been rectified and the Data is loading fine in the development system.
Now I am in another peculiar situation.
The routines, after debugging, are working good in the development system but after transporting to Quality system for testing, they are failing there. Iam facing the same old problem there again. The transports are checked, they were done properly. The ABAPer is satisfied with the transported code. If you can then please guide me.Iam closing this thread and opening a new thread with Subject as " In different behavior of Routines"
Thank you once again Jen. Full points assigned to you.
Kind Regards
SHL

Out Put Problem in Sales Order

Hi ,
i created a sales order , but prinit out is not generating automatically for one particular customer, rest of customers ok , it's working fine
and when i assign output type BA00 manually in sales order , system throwing error
"Requirements are not checked with manual create"
message no :Message no. VN085
Hint: <b>this error is only for this particular customer</b>
hope u people can find a solution for me ,
Thanks & Regards
Venkat.Dhanemkula
Message was edited by:
Venkat

PLs check delivery block in order, if yes , u check requirements for delivery blocks
give me feedback immediatly
Raj

Out put problem

Hi experts,
i have a problem with my script, my script name is zmodify_form, my report name is zmodify and the trancation code of the script is zmodify, if i make any changes in form (allignments and formats) i can see the changes that made by me in printing test . But when i execute the tcode it shows the same existing screen. wat can i do for this?
<MOVED BY MODERATOR TO THE CORRECT FORUM>
Edited by: Alvaro Tejada Galindo on Sep 28, 2011 3:53 PM

Hi,
In Background u can get the Maximum length 250 only.
Regards,
Balavardhan.K

Regarding ALV out put problem

hi
i have a internal table with the following structure
TYPES: begin of ty_final.
types: b_bseg type bseg.
types: k_kna1 type kna1.
types: l_lfa1 type lfa1.
types: s_ska1 type ska1.
types: a_anlu type anlu.
TYPES:   End of ty_final.
DATA: lt_final TYPE STANDARD TABLE OF ty_final ,
      wa_final TYPE ty_final.
after i fill my final internal table i need to get the output in ALV grid , i tried to pass the internal table to ALv Grid function module but I am getting shortdump .
is it possible to to get the output with this complex structure?
Moderator message: please choose more descriptive subject lines for your posts.
Edited by: Thomas Zloch on Jun 8, 2011 4:38 PM

here is the short dump , I think the ALV program doesnt get the internal table value , because the value resides in deep structure . if i am wrong correct me.
Short text
Field symbol has not yet been assigned.
What happened?
Error in the ABAP Application Program
The current ABAP program "SAPLSLVC" had to be terminated because it has
come across a statement that unfortunately cannot be executed.
Error analysis
You attempted to access an unassigned field symbol
(data segment 32821).
This error may occur if
- You address a typed field symbol before it has been set with
ASSIGN
- You address a field symbol that pointed to the line of an
internal table that was deleted
- You address a field symbol that was previously reset using
UNASSIGN or that pointed to a local field that no
longer exists
- You address a global function interface, although the
respective function module is not active - that is, is
not in the list of active calls. The list of active calls
can be taken from this short dump.
Trigger Location of Runtime Error
Program                                 SAPLSLVC
Include                                 LSLVCF36
Row                                     3.267
Module type                             (FORM)
Module Name                             FILL_DATA_TABLE
Source Code Extract
Line
SourceCde
3237
alv_style_align_center_top.
3238
endif.
3239
3240
append ls_lvc_data to ct_lvc_data.
3241
endif.
3242
3243
3244
Column per Fieldcat Entry
3245
3246
loop at it_fcat_local assigning <ls_fcat>.
3247
clear: ls_lvc_data-href_hndl,
3248
ls_lvc_data-drdn_hndl,
3249
ls_lvc_data-style,
3250
ls_lvc_data-style2,
3251
ls_lvc_data-style3,
3252
ls_lvc_data-style4,
3253
ls_lvc_data-maxlen.
3254
3255
clear: lt_color_lvc, lt_color_slis.
3256
3257
add 1 to ls_lvc_data-col_pos.
3258
3259
if not <ls_fcat>-indx_field is initial.
3260
assign component <ls_fcat>-indx_field
3261
of structure <ls_data> to <l_field_value>.
3262
else.
3263
assign component <ls_fcat>-fieldname
3264
of structure <ls_data> to <l_field_value>.
3265
endif.
3266
>>>>>
macro_cell_data_get
3268
<ls_fcat>
3269
<ls_data>
3270
<l_field_value>
3271
ls_lvc_data-value.
3272
3273
*>>> new API
3274
if ir_salv_adapter is bound.
3275
clear ls_lvc_data-style.
3276
3277
color
3278
if g_gui_type ne 1.
3279
if <ls_fcat>-key eq abap_true.
3280
ls_lvc_data-style = alv_style_color_int_key.
3281
elseif l_style_color is initial
3282
and ( <ls_fcat>-emphasize is initial or
3283
<ls_fcat>-emphasize = '$' ).
3284
if <ls_stin>-counter is initial.
3285
ls_lvc_data-style = alv_style_color_normal.
3286
else.

Problem with Input out put parametes of IViews in callable objects

Dear Friends,
I have designed model which contains 2 IViews
Apply leave IViews
Approve leave Iviews
In both the cases i have exposed the in & out parameters using start & end point.
Finally deployed in portal successfully
Guided procedures ->Design Time
I have created folder
when i create callable objects using this IViews , i dont see the input & out put parameters exposed in context parameters tab for this IView.
Any step i missed.
Regards
shekar Chandra

HI Nishi
struck up with minor problem,
We have a application designed in VC.It contains
Create request
Approve Request(approve or reject buttons)
IF approved then
a.Book Request IView
b.Summary Iview
If Rejected then
a.rejected IView.
When i am designing Process with Sequential block,
all the actions namely
create request
appprove request
reject
book
summary
are processingone one by as action mentioned in sequential block irrespective of approved or rejected.
I cannot go for alternative block, since the result state buttons are desinged in IView only namely(Approve/reject).
How to overcome this probelm any suitable solution?
regards
shekar chandra

Problem with dispalying out put of report RLLI0400

i have added one field in the report by copieng the report to zprogram...
i want see the out of the report ,but i am not getting any out put just giving the message saying that tha document is printed...
i need to change code in this report?
i need to change any thing in form DRUCKER_EINSCHALTEN,
if yes please tell me what changes are needed.....

Hi Kranthi,
in sub routine DRUCKER_EINSCHALTEN omit the code NO-DIALOG with NEW_PAGE command. i think it is genreating output into a spool request and suppress the dialog. if you omit this NO-DIALOG it will generate output.
Regards
Krishnendu

Ultrabeat multiple out put problem

Similar Messages

Maybe you are looking for