Unable to access the windows side of my split hard drive...
I've split my hard drive so that I could run CAD(windows based). How do I access that hard drive? When I start my computer it automatically goes to the apple side of things and there is no option to access the windows side. Please help!!
Hi Aonelisa,
Welcome to the Support Communities!
The article below may be able to help you with this.
Click on the link to see more details and screenshots.
Mac Basics: Using Windows on your Mac via Boot Camp
http://support.apple.com/kb/ht1461
Boot Camp Assistant creates a partition just for Windows without erasing your existing OS X volume.
After installation, you can switch between Windows and OS X by holding the Option (Alt) key at start up. Or, use the Startup Disk control panel in Windows (installed with Boot Camp support software) or the OS X Startup Disk preference pane to set the default operating system to use each time the computer starts up.
OS X Mountain Lion: Change your startup disk
http://support.apple.com/kb/PH10603
Cheers,
- Judy
Similar Messages
-
On imac 10.6.8 using current version of Aperture. How can I access the Aperture Library on my external hard drive that I use with time machine for backup? I can only access the application but not the library..
Go into Time Machine (the program not the bundle on the extrnal disk) and using Time Machine's browser go to the Folder where the library lives. You could look in the library bundle in Time Machine but that won't really tell you much,
If you want to make sure it truely has backed up your library you will need to restore it and open the restored library with Aperture.
If all this still has you confused you need to read up on Time Machine in order to get a feel for how it works, for what it is doing and for how to restore files from it. -
I was just about to order a photo book, using photos stored on an external hard drive. I organised the book and pressed 'buy'. IPhotos instructed me that I needed to upgrade and so I went on the ASpp store, bought the upgrade and installed as directed. I then used the iPhoto Library upgrader as directed.
After the iPhoto upgrade I can no longer access the photos stored on my external hard drive. I am able to access the photos stored on my internal hard drive - the remainder (including the photo album) seem to have vanished into thin air.
Any suggestions please?What format is the external drive?
-
My hard disk crashed and I cannot find out how to "contact customer service" other than this forum. The website seems to just take me in a circle. I need to de-activate a license but cannot access the software due to a crashed hard drive. Please help.
Hi Anthony ,
Here is the link to connect with Adobe Chat Support.
https://helpx.adobe.com/adobe-connect/kb/connect-chat-support.html
Hope your query gets resolved .
Regards
Sukrit Dhingra -
How to back up the Windows side of your Apple computer
Hello friends,
As I get more involved in the Windows side of my Apple computer (Macbook Pro Snow Leopartd with boot camp) I am wondering what is the proper way to back up the files I have on the Windows side to an external hard drive? I can obviously easily copy my documents, pictures and videos, but what about the contents of my copy of Microsoft Outlook (all my emails and all my contacts), the copy of iTunes I have on the Windows side and the list of "favorites" that I have in my Internet Explorer (again all of these programs are on the Windows side).
Is there a way to back them up so that if my Apple computer dies, and I get a new Apple again with boot camp and Windows, I can reinstall them on to the new computer and have them functioning just like before (the way one can with programs on the Macintosh side)?
Your help would be appreciated.
Thank you.
CosmasadGood morning folks, Twonails, ScuseMe and Hatter—
Several questions:
Good to hear about your experiences with Winclone, Paragon’s HDM 2011 Suite and Acronis True Image 2011. Would you mind telling me what it is about these programs that have made them so useful to you? I have looked at their websites online but would love to hear it described in plain words. For example, how do these programs differ from Windows 7’s built-in Backup and Restore and Create a System Image? Do they work better with Windows mounted on Boot Camp?
ScuseMe, when one encounters a problem like you did with the audio drivers, couldn’t you have used system restore to roll the clock back to the point before you installed the drivers? Does system restore not always fix these kind of problems?
Finally, TwoNails, can you tell me what exactly you mean by “yes several drivers had to be updated but it still booted and functioned well”? By drivers do you mean the drivers that control printers and if so, how does one know whether they need updating after you do a reinstall?
Thank you all. Your patience is appreciated.
Cosmasad -
Can I back up the windows side of my Mac with Time Capsule too?
I use VMware to access the Windows side and have a couple of programs on it after I upgraded to Lion which does not support them. But now how to back up?
vois0011 wrote:
I have no idea what to do, I've tried multiple things and I still cant acess my wifi network when im on the windows side of my computer
You provided no information about your computer, your operating system, network, errors, or Windows version. But I'll take some guesses.
What did you try? What happens when you try? Any error messages? Did you download and install the Windows Support Software, or install it from your Snow Leopard Install Disk if you are using Snow Leopard? Did you look in the Windows Help menu to see how to set up wifi in Windows? -
Hello,
I would like to know how to change the partitioned drive on my mac to give more resources to the windows side of the machine?
i have one other little problem, If I am running the windows side of the machine the mac book's internat speakers produce no sound, but if the content is streamed to my TV the audio id there and working right.When you look in the jack on the side of the computeryou see a red light shinig through itand the speaker icon tells me that the speaker output is at 100% even though there is no sound coming out of the internal speakers.
Thank you all in advance for sny help
JTNTo change the partitions on your MBP, go to DISK UTILITY>PARTITION and follow the instructions.
Regarding your sound issue, the red light in the audio output port indicates that the switch is set to provide audio to earphones and the internal speakers are disconnected. To alleviate the problem try a repeated insertion of the earphone jack. If that does not get the internal speakers functioning, the get a cocktail stirrer or tooth pick and jiggle it inside. If still no success, the Apple store.
Ciao. -
Unable to access the data from Data Management Gateway: Query timeout expired
Hi,
Since 2-3 days the data refresh is failing on our PowerBI site. I checked below:
1. The gateway is in running status.
2. Data source is also in ready status and test connection worked fine too.
3. Below is the error in System Health -
Failed to refresh the data source. An internal service error has occurred. Retry the operation at a later time. If the problem persists, contact Microsoft support for further assistance.
Error code: 4025
4. Below is the error in Event Viewer.
Unable to access the data from Data Management Gateway: Query timeout expired. Please check 1) whether the data source is available 2) whether the gateway on-premises service is running using Windows Event Logs.
5. This is the correlational id for latest refresh failure
is
f9030dd8-af4c-4225-8674-50ce85a770d0
6.
Refresh History error is –
Errors in the high-level relational engine. The following exception occurred while the managed IDataReader interface was being used: The operation has timed out. Errors in the high-level relational engine. The following exception occurred while the
managed IDataReader interface was being used: Query timeout expired.
Any idea what could have went wrong suddenly, everything was working fine from last 1 month.
Thanks,
RichaNever mind, figured out there was a lock on SQL table which caused all the problems. Once I released the lock it PowerPivot refresh started working fine.
Thanks. -
Hi,
I am monitoring AD server from SCOM 2012 R2. My management server goes into waning state. When i run Health explorer then it come back in the healthy state but after some time it again goes into warning state. After seeing alert i found that a alert is coming
again and again i.e. Operations Manager Failed to Access the Windows Event Log.The description of alert is mention below
The Windows Event Log Provider is still unable to open the DhcpAdminEvents event log on computer 'nc2vws12ad5.corp.nathcorp.com'.
The Provider has been unable to open the DhcpAdminEvents event log for 64080 seconds.
Most recent error details: The RPC server is unavailable.
Please suggest me how to resolve this so that my management server will again come back in healthy state.
Thanks
AbhishekHi Abhishek,
As i mentioned earlier the Alert resolution says the same points.
Can you give details on the below ?
Is there really a log named "Dhcpadminevents" in the MS's Event viewer ?
Did you recently configure any new alert where you mentioned "Dhcpadminevents"
as a event log location ?
If yes then what is the target you selected for the rule / monitor there ?
Can you post the results for analysis ?
Gautam.75801 -
UNABLE TO ACCESS THE INTERNET FROM LOCAL PROVIDER ON A SITE-TO-SITE VPN CONNECTION
Dear All,
I have a site-to-site connection from point A to point B. From point B i am unable to access the internet from local internet provider.
I am trying to ping from 192.168.20.1 the dns 8.8.8.8 but i receive the message "destination net unreachable".
When i run "show ip nat translation" i receive nothing.
The vpn connection is working properly, i can ping the other side 192.168.10/24
Below is the configuration of the cisco router on point B.
dot11 syslog
ip source-route
no ip dhcp use vrf connected
ip dhcp excluded-address 192.168.21.254
ip dhcp pool voice
network 192.168.21.0 255.255.255.0
default-router 192.168.21.254
option 150 ip 192.168.5.10
ip cef
ip domain name neocleous.ru
ip inspect name IOS_FIREWALL tcp
ip inspect name IOS_FIREWALL udp
ip inspect name IOS_FIREWALL icmp
ip inspect name IOS_FIREWALL h323
ip inspect name IOS_FIREWALL http
ip inspect name IOS_FIREWALL https
ip inspect name IOS_FIREWALL skinny
ip inspect name IOS_FIREWALL sip
no ipv6 cef
multilink bundle-name authenticated
vty-async
isdn switch-type primary-net5
redundancy
crypto isakmp policy 5
hash md5
authentication pre-share
group 2
crypto isakmp policy 10
encr aes
authentication pre-share
group 2
lifetime 28800
crypto isakmp policy 50
encr 3des
hash md5
authentication pre-share
group 2
crypto isakmp key Pb85heuvMde9Wdac5Qohha7lziIf142u address [ip address]
crypto isakmp invalid-spi-recovery
crypto isakmp keepalive 10
crypto ipsec transform-set TRANSET esp-aes esp-sha-hmac
crypto ipsec transform-set TRANSET2 esp-des esp-md5-hmac
crypto ipsec df-bit clear
crypto map CryptoMAP1 ipsec-isakmp
set peer [ip address]
set transform-set TRANSET
match address CryptoACL
interface FastEthernet0/0
description Primary Provider
ip address [PUBLIC IP MAIN PROVIDER] 255.255.255.252
ip access-group outside_acl in
ip mtu 1390
ip nat outside
ip virtual-reassembly in
load-interval 30
duplex auto
speed auto
crypto map CryptoCY
crypto ipsec df-bit clear
interface FastEthernet0/1
description TO LAN
no ip address
load-interval 30
speed 100
full-duplex
interface FastEthernet0/1.1
description DATA VLAN
encapsulation dot1Q 20
ip address 192.168.20.254 255.255.255.0
ip access-group inside_acl in
ip nat inside
ip inspect IOS_FIREWALL in
ip virtual-reassembly in
ip tcp adjust-mss 1379
interface FastEthernet0/1.2
description VOICE VLAN
encapsulation dot1Q 21
ip address 192.168.21.254 255.255.255.0
interface Serial0/2/0:15
no ip address
encapsulation hdlc
isdn switch-type primary-net5
isdn incoming-voice voice
no cdp enable
interface FastEthernet0/3/0
no ip address
ip access-group outside_acl in
ip nat outside
ip virtual-reassembly in
shutdown
duplex auto
speed auto
crypto map CryptoCY
ip local pool VPNPool 192.168.23.2 192.168.23.10
ip forward-protocol nd
ip http server
no ip http secure-server
ip nat inside source list nat_list interface FastEthernet0/3/0 overload
ip route 0.0.0.0 0.0.0.0 [default gateway ip]
ip access-list standard VTY
permit 192.168.20.0 0.0.0.255
ip access-list extended CryptoACL
permit ip 192.168.20.0 0.0.0.255 192.168.3.0 0.0.0.255
permit ip 192.168.21.0 0.0.0.255 192.168.5.0 0.0.0.255
permit ip 192.168.21.0 0.0.0.255 192.168.6.0 0.0.0.255
permit ip 192.168.21.0 0.0.0.255 192.168.12.0 0.0.0.255
permit ip 192.168.21.0 0.0.0.255 192.168.2.0 0.0.0.255
permit ip 192.168.20.0 0.0.0.255 192.168.10.0 0.0.0.255
permit ip host 192.168.22.1 192.168.5.0 0.0.0.255
permit ip host 192.168.20.1 192.168.5.0 0.0.0.255
permit ip host 192.168.22.1 192.168.6.0 0.0.0.255
ip access-list extended DFBIT_acl
permit tcp any any
ip access-list extended inside_acl
permit ip 192.168.20.0 0.0.0.255 host 192.168.3.35
permit ip 192.168.20.0 0.0.0.255 host 192.168.3.39
permit ip 192.168.20.0 0.0.0.255 host 192.168.3.23
permit ip 192.168.20.0 0.0.0.255 host 192.168.3.18
permit ip 192.168.20.0 0.0.0.255 host 192.168.3.55
permit ip 192.168.20.0 0.0.0.255 host 192.168.10.144
permit ip 192.168.20.0 0.0.0.255 host 192.168.10.146
permit ip 192.168.20.0 0.0.0.255 host 192.168.10.141
permit ip host 192.168.20.253 host 192.168.3.21
permit ip host 192.168.20.254 host 192.168.3.21
permit ip 192.168.20.0 0.0.0.255 host 192.168.3.10
permit ip 192.168.20.0 0.0.0.255 host 192.168.20.254
ip access-list extended nat_list
deny ip host 192.168.20.254 192.168.10.0 0.0.0.255
deny ip host 192.168.20.254 192.168.3.0 0.0.0.255
deny ip host 192.168.20.1 192.168.3.0 0.0.0.255
deny ip host 192.168.20.1 192.168.10.0 0.0.0.255
deny ip host 192.168.20.2 192.168.3.0 0.0.0.255
deny ip host 192.168.20.2 192.168.10.0 0.0.0.255
permit ip host 192.168.20.1 any
permit ip host 192.168.20.2 any
permit ip host 192.168.20.254 any
ip access-list extended outside_acl
permit gre any host [ip address]
permit esp any host [ip address]
deny ip any any
ip sla 2
icmp-echo 192.168.10.254 source-interface FastEthernet0/1.1
frequency 180
timeout 500
ip sla schedule 2 life forever start-time now
logging 192.168.3.21
route-map DFBIT_routemap permit 10
match ip address DFBIT_acl
set ip df 0
route-map ISP2 permit 10
match ip address nat_list
match interface FastEthernet0/3/0
route-map nonat permit 10
match ip address nonat_acl
route-map ISP1 permit 10
match ip address nat_list
match interface FastEthernet0/0You cannot access internet, because all traffic is tunneled for VPN !!!!
Please see cisco tech documentation and bypass traffic for internet.
eg. if lan traffic is going from site a to site b then through vpn
else
lan traffic to internet (any) should be out thorugh the vpn . -
In Mavericks Mail I am unable to access the BCC: line for sending a blind carbon copy. I open my Contacts list, select a person, and when I click on the BCC: box above in the Contacts window, the person is not entered onto a line in the email for receiving a BCC: and the BCC: line does not even appear. Thoughts from all you experts out there?
I managed to find the answer to my own question. As shown in the screenshot below, the header field area on a new message contains a small lined box in the lower left corner of it. If you click on the lined box, it allows you to customize the Header field, such as adding a BCC: line.
Message was edited by: Radiation Mac -
Content generation
[Error: Unable to access the output directory. The directory is not writable, so the folio cannot be saved.]
This means?
This is fun BTW. Two days and two different silly errors applying themselves arbitrarily. Yesterday was the network, today its this.heres the fix i used for on a Mac
1. While in the Finder, select the menu command Finder > Preferences.
2. In the General panel, ensure the option "Connected Servers" is selected under the heading "Show these items on the desktop:", then close the preferences dialog box.
3. Choose the menu command Finder > Hide Others.
4. Close all open Finder windows to ensure you can see all items on your desktop.
5. If you locate what appears to be a mounted volume with the name "Users", Control + Click on its icon and choose the contextual menu command Eject "Users".
6. Add or update your article(s).
7. Cross fingers
8. If doesn't work ask for a refund -
I am using pse 11 0n windows vista for years and it has suddenly started freezing on starting, I am now unable to access the organizer it freezes on the blue screen, the editor can be opened. Have removed and reinstalled but is still occurring. Have changed the files as suggested, am unable to open as administrator
'The installer has insufficient privileges to modify this file C:\Program Files (x86)\Common Files\Apple\Apple Application Support\Web kit.resources\inspector\Images\Spinner Inactive Selected.gif.'
That one's consistent with disk/file damage. The first thing I'd try with that is running a disk check (chkdsk) over your C drive.
XP instructions in the following document: How to perform disk error checking in Windows XP
Vista instructions in the following document: Check your hard disk for errors
Windows 7 instructions in the following document: How to use CHKDSK (Check Disk)
Select both Automatically fix file system errors and Scan for and attempt recovery of bad sectors, or use chkdsk /r (depending on which way you decide to go about doing this). You'll almost certainly have to schedule the chkdsk to run on startup. The scan should take quite a while ... if it quits after a few minutes or seconds, something's interfering with the scan.
Does the chkdsk find/repair any damage? If so, can you get an install to go through properly afterwards? -
Ref: Unable to access the endpoint(s): In BPEL
Hi,
Here My requirement is, I wants Invoke WSDL into my Composite.
My is Domain like http://s008apl011001:7001.
But that WSDL is in diff Domain like http://v110aplffc002: 8001.
This time I am getting below Error:
Non Recoverable System Fault :
Unable to access the following endpoint(s): http://v110aplffc002:8001/soa-infra/services/default/ContentManagement/ContentManagement_ep
I am using SOA suite version 11.1.1.6.
In my composite I have added below security policies like below
<reference name="ContentManagement"
ui:wsdlLocation="http://v110aplffc002:8001/soa-infra/services/default/ContentManagement/ContentManagement.wsdl">
<interface.wsdl interface="http://www.absa.co.za/afs/ContentManagement#wsdl.interface(contentMgt_ptt)"/>
<binding.ws port="http://www.absa.co.za/afs/ContentManagement#wsdl.endpoint(ContentManagement_ep/execute_pt)"
location="ContentManagement_ep.wsdl" soapVersion="1.1">
*<wsp:PolicyReference URI="oracle/wss_username_token_client_policy"*
orawsp:category="security" orawsp:status="enabled"/>
*<property name="oracle.webservices.auth.password">p$ssword01</property>*
*<property name="oracle.webservices.auth.username">weblogic</property>*
*<property name="weblogic.wsee.wsat.transaction.flowOption"*
type="xs:string" many="false">WSDLDriven</property>
*<property name="oracle.webservices.proxyHost" type="xs:anyURI"*
many="false" override="may"> http://v110aplffc002</property>
*<property name="oracle.webservices.proxyPort" type="xs:integer"*
many="false" override="may">8001</property>
*<property name="oracle.webservices.local.optimization" type="xs:boolean"*
many="false" override="may">true</property>
</binding.ws>
</reference>
Then deployed SOA server,It's deployed successfully. At testing time it's throwing below Error :
Non Recoverable System Fault :
<bpelFault><faultType>0</faultType><remoteFault xmlns="http://schemas.oracle.com/bpel/extension"><part name="summary"><summary>oracle.fabric.common.FabricInvocationException: Unable to access the following endpoint(s): http://v110aplffc002:8001/soa-infra/services/default/ContentManagement/ContentManagement_ep</summary></part><part name="detail"><detail>Unable to access the following endpoint(s): http://v110aplffc002:8001/soa-infra/services/default/ContentManagement/ContentManagement_ep</detail></part><part name="code"><code>null</code></part></remoteFault></bpelFault>
Please any one provide solutions for above error.
What I do for above error.
Thanks in Advance
Regards
AnilLooks like http://v110aplffc002: 8001 is not accessible from http://s008apl011001:7001. if s008apl011001 is windows server check from the browser if you are able to access http://v110aplffc002:8001/soa-infra/services/default/ContentManagement/ContentManagement_ep?WSDL and see the wsdl file. if linux then try curl and see if you can access the wsdl . Most likely the url on v110aplffc002:8001 is not accessible from s008apl011001 .
-
I have just sought to update my lightroom and am now unable to access the develop function and get a note stating that I have reduced functionality what it this about and how do I get my product back
Hi there
I have version 5.7 and every time I opened it I was told that updates are available and to click on the icon to access these. Instead it just took me to the
adobe page with nowhere visible to update. I then sought to download lightroom cc and this is when I could not access the 'develop' section due to reduced
functionality It was apparent that my photos had been put in cc but no way to access them unless I wanted to subscribe.
I have since remedied the problem as my original lightroom 5.7 icon is still available on the desktop and have gone back to that. I do feel that this is a bit
of a rip off and an unnecessary waste of my time though.
Thank you for your prompt reply by the way.
Carlo
Message Received: May 04 2015, 04:52 PM
From: "dj_paige" <[email protected]>
To: "Carlo Bragagnolo" <[email protected]>
Cc:
Subject: I have just sought to update my lightroom and am now unable to access the develop function and get a note stating that I have
reduced functionality what it this about and how do I get my product back
dj_paige created the discussion
"I have just sought to update my lightroom and am now unable to access the develop function and get a note stating that I have reduced functionality what it
this about and how do I get my product back"
To view the discussion, visit: https://forums.adobe.com/message/7510559#7510559
>
Maybe you are looking for
-
Not able to access human task form (11.1.1.4)
I installed SOA Suite with BPM Suite 11.1.1.4. I ran into quite a few issues. The biggest one is I am not able to access the human task form in BPM workspace even for the new application created in 11.1.14. Do you have such issue? I am not sure if it
-
Why cant I find an add-on to open a new tab in my home page on Firefox 5?
I have been able to open a new tab in my home page (Google in my case) in all of the other versions of Firefox. I am a loyal user but this is frustrating. I cannot locate an add-on for this feature. Is there something out there?
-
JVC KS-PD100 doesn't charge my iPhone 3G.
My JVC KS-PD100 works fine and charges my old iPhone, I have just upgraded to iPhone 3G but when I plug into my JVC KS-PD100 adapter, it doesn't charge my iPhone 3G any more, is it because of the iPhone 3G hardware change? Is there any fix for it? li
-
Why does the screen turn black? I was using it normally and it all of a sudden faded to black and hasnt come back on since yesterday. You can see the back light but no image on the screen. Ive plugged it in and it vibrates that its connected but stil
-
We are using Form Designer 8.1.1 with Reader 8.1.1 Whenever a form is accessed via Reader it opens with a zoom level of 177% which fills the width of the screen. The form user has to retset the zoom level to 67% in order to see a complete page. Can t