Unable to enter administration page of NSS 326

Even after a soft reset, we are unable to enter the administration page of our NSS 326, and even through the NSS Discovery tool, we can't configure as it asks the admin username and password ( the default is expected to be admin-admin after the soft reset but doesn't work). Any help would be useful. Thank you in advance.

That may be because the clock settings on your computer are not the same as the clock in general, or perhaps because the clock on your computer is dead..
to deal with you can reset your clock on your computer or sertivikat looking at options on the right side and then choose to agree if it has been found..

Similar Messages

Unable to load web pages. This is what I get when I enter them; Unable to connect

Yesterday I turned on my computer & was not able to use Firefox. Nothing had been changed on my computer. No web pages will load. When I hit enter this is the message I get:
Unable to connect Firefox can't establish a connection to the server at www.geocaching.com.
The site could be temporarily unavailable or too busy. Try again in a few moments. If you are unable to load any pages, check your computer's network connection. If your computer or network is protected by a firewall or proxy, make sure that Firefox is permitted to access the Web.

It most likely means your internet connection is out. Wait a little while then try again. You might also want to reboot your computer. If that doesn't work, please reply.

Unable to enter router setup page

my router is WRT54G..i can only enter into the setup page once..after i close my IE..i am unable to enter anymore..must do a reset to enter again..is my router faulty ? plsssss help

well.....possibly a firmware issue...follow the steps :
1)go to ftp.linksys.com/pub/network and download the tftp.exe file....
2)go to www.linksys.com/download and download the latest firmware for the corresponding version no. of WRT54G ...
3)run the tftp.exe file
4)here, the server is router's ip add ( 192.168.1.1 ) , password is router's password ( by default it's "admin" ) and browse the firmware file and click upgrade
5)once the firmware is upgraded , reset the router and reconfigure it....

WAAS 3.5, unable to login to administrator page.

Hello All
We recently installed WAAS Mobile Server 3.5,the installation was sucessful, all the pre requisite was fulfilled for the installation
But we are unable to log in to the administration page, keep getting the erro invalid username and password.I did some check on the IIS but no results, would appreciate any assistance on this.
Thank you,
Subu

Hi
After you install the WAAS Mobile Server, you should be able to open the WAAS Mobile Manager Login page and login using the default usernames and password. The default username is admin and password is default
This is described in the WAAS Mobile Server installation guide on Page number 19 in the link below:
http://www.cisco.com/en/US/docs/app_ntwk_services/waas/waas_mobile/v3.5/configuration/administration/guide/CiscoWAASMobileAdminGuide_3_5.pdf
Regards
Rama

Unable to enter a Division for which I have proper credentials, via the GUI

I have a Division which I am unable to enter, either as a student or as the full site Administrator, from the GUI.
When I log into the main Site page, I see the link for the Division (as I should - I have DOWNLOAD permissions for the Division). However when I click the link (the thumbnail image) I am always, 100% of the time, rejected and sent to the login page. Ignoring that, I still have all of my proper credentials and may continue to freely access other parts of the site.
In the past, I had this exact behavior on (1) a Division "RobotCourses:PSYC" (Psychology), and (2) my main site breadcrumb, which appears at the top of the site page to the right of the "iTunes U" breadcrumb and says "Maiko Covington @ University of Illinois..." For reasons completely unknown to me, this behavior resolved itself yesterday, clicking both of those objects works as expected, although NO one at our site with any edit access did anything on the server.
However, the same behavior has now reappeared, this time on a Division "RobotCourses:CLCV" (Classical Civilizations). Again, I have not done any editing of that Division, nor had anyone logged into it (these Divisions are in a test area where I am developing automation tools).
I am, quite frankly, stumped. But I've done some investigation.
SETUP:
The Division has identity "RobotCourses:CLCV".
This Division contains a single Course with identity "RobotCourses:CLCV:CLCV115:CLCV115All-13564".
Both the Division and the Course are restricted to properly registered academic students. I have developed automation code in a login portal which grants credentials for RobotCourses:CLCV to students registered for courses in the CLCV department (Classical Civilizations) and credentials for RobotCourses:CLCV:CLCV115:CLCV115All-13564 to students registered for CLCV 115 (Classical Civilizations 115 - Mythology of Greece and Rome) specifically.
The Permissions set on RobotCourses:CLCV in particular are:
<Permission>
<Credential>Authenticated@urn:mace:itunesu.com:sites:illinois.edu</Credential>
<Access>No Access</Access>
</Permission>
<Permission>
<Credential>gakusei@urn:mace:itunesu.com:sites:illinois.edu:RobotCourses:CLCV</C redential>
<Access>Download</Access>
</Permission>
The point is to deny access to Authenticated@ (merely authenticated students) and then specifically grant it for people given a "gakusei" credential for RobotCourses:CLCV in particular.
(Note here that "gakusei" is a Japanese word meaning "student," I am using it in my credentials to ensure that my credentials and permissions are not affected by other credentials named "student" set at upper levels and used by some live users of the site, as we do not have a segregated development environment. It is our lowest level of access beyond mere Authenticated@..., designed to give students access to download and "surf to" Divisions and Courses.)
*LOGIN: ISSUING CREDENTIALS:*
The login portal code works successfully, and so when a student "Jane Doe" logs in, she is in fact given appropriate credentials (as she is actually registered for CLCV 115 here at UIUC). From the code generating her login URL, I see:
Issued credentials:
gakusei@urn:mace:itunesu.com:sites:illinois.edu:RobotCourses:CLCV
gakusei@urn:mace:itunesu.com:sites:illinois.edu:RobotCourses:CLCV:CLCV115:CLCV1 15All-13564
gakusei@urn:mace:itunesu.com:sites:illinois.edu:RobotCourses:STAT
gakusei@urn:mace:itunesu.com:sites:illinois.edu:RobotCourses:STAT:STAT100:STAT1 00X1-13570
(You can see she is also registered for STAT 100).
With the default login URL thus generated, she is taken to the top level of the Site in iTunes, and in fact sees thumbnail links for both STAT (Statistics) and CLCV (Classical Civilizations). Clicking on STAT takes her to the STAT Division where she can then enter the Course STAT 100 with no problems.
*PROBLEM: CAN'T GET TO CLCV FROM THE MAIN PAGE IN THE GUI*
HOWEVER! Clicking on CLCV brings up the login page. If she ignores the login page, she can still access the rest of the site, including STAT, just fine. Logging in again (reissuing her credentials) does not help the situation.
Note that this is not a problem only for Jane Doe, the same thing happens for anyone in CLCV and in fact happens for me as Administrator of the whole site with full access, even.
*ACCESS DIRECTLY TO THE DIVISION BY URL WORKS*
With a slight modification to the login to allow access directly to the RobotCourses:CLCV Division (by adding the handle of the Division to the end of the location), credentials are issued exactly as before:
Issued credentials:
gakusei@urn:mace:itunesu.com:sites:illinois.edu:RobotCourses:CLCV
gakusei@urn:mace:itunesu.com:sites:illinois.edu:RobotCourses:CLCV:CLCV115:CLCV1 15All-13564
gakusei@urn:mace:itunesu.com:sites:illinois.edu:RobotCourses:STAT
gakusei@urn:mace:itunesu.com:sites:illinois.edu:RobotCourses:STAT:STAT100:STAT1 00X1-13570
and she is taken to the Division page, SUCCESSFULLY. So, it seems she actually HAS access, as expected.
*ACCESS CONFIRMED WITH DEBUGGING:*
Writing some code to generate not the actual login URL but rather a link that takes me to an "iTunes U Access Debugging" page for the Division (figured this out by reading some other posts! :)) I am taken to a page with the following:
(at generated URL https://deimos.apple.com/WebObjects/Core.woa/Browse/illinois.edu.1945806043/xxx5 64?credentials=....)
Received
Destination illinois.edu.1945806043
Identity "Jane X Doe" <[email protected]> (jxdoe) [xxxxxxxxx]
Credentials gakusei@urn:mace:itunesu.com:sites:illinois.edu:RobotCourses:CLCV; gakusei@urn:mace:itunesu.com:sites:illinois.edu:RobotCourses:CLCV:CLCV115:CLCV1 15All-13564; gakusei@urn:mace:itunesu.com:sites:illinois.edu:RobotCourses:STAT; gakusei@urn:mace:itunesu.com:sites:illinois.edu:RobotCourses:STAT:STAT100:STAT1 00X1-13570
Time 1236877947
Signature 42ccef92a3298684a7a09eed45adb6b788a700c01645b8b423d33ace120650b0
Analysis
The destination string is valid and the corresponding destination item was found.
The identity string is valid and provides the following information:
Display Name Jane X Doe
Email Address [email protected]
Username jxdoe
User Identifier xxxxxxxxx
The credential string is valid and contains the following 4 recognized credentials:
1. gakusei@urn:mace:itunesu.com:sites:illinois.edu:RobotCourses:CLCV
2. gakusei@urn:mace:itunesu.com:sites:illinois.edu:RobotCourses:CLCV:CLCV115:CLCV1 15All-13564
3. gakusei@urn:mace:itunesu.com:sites:illinois.edu:RobotCourses:STAT
4. gakusei@urn:mace:itunesu.com:sites:illinois.edu:RobotCourses:STAT:STAT100:STAT1 00X1-13570
The time string is valid and corresponds to 2009-03-12 17:12:27Z.
The signature string is valid.
Access
Because the received signature and time were valid, the received identity and credentials were accepted by iTunes U.
In addition, the following 2 credentials were automatically added by iTunes U:
1. All@urn:mace:itunesu.com:sites:illinois.edu
2. Authenticated@urn:mace:itunesu.com:sites:illinois.edu
With these credentials, you have browsing and downloading access to the requested destination.
(In case you think to check the sums, be aware I've actually changed the student's name for this example.)
So, as expected, I have access, in fact the student DOES have access, visiting the Division page directly (specifiying its handle as part of the desired location).
*IT'S ONLY CLICKING THE THUMBNAIL ON THE MAIN PAGE THAT BREAKS*
Because the problem is only apparent when clicking the icon for the Division on the main Site page, I have no way (that I know of) to get any information about precisely WHAT is going on, what possibly differs in the GUI-click situation from the "generate me a URL that takes me right there" situation.
At that point I'm fully in the GUI, I'm not sending anything via web services, so I have no idea how I can proceed to debug this from here.
I'm also quite confused at the sudden appearance of this behavior, and the disappearance of this behavior from RobotCourses:PYSC, another Division that was broken in this same way all last week but which magically resumed allowing me access yesterday.
Any suggestions, hints, or advice would be very welcome. Has anyone else even seen behavior similar to this?
Thanks for any information you might have.

Maiko,
I'm confess I'm still trying to get a handle on your problem. You do a fantastic job of describing it ... but I'm just trying to picture it accurately in my head.
I think, were I in your shoes, I'd begin by looking at what the debug page has to say for the specific destination in which you're interested in fixing. In other words, I'm not clear on where, exactly, this destination points ...
Destination illinois.edu.1945806043
Is that your site, or the division within your site that you want to fix? "Normally", you do not need to specify a site handle to get to your site within your transfer CGI ... if you say "uillinois.edu", it's enough to transfer your users to iTunes U ... but every site still has a handle, and you could, if you wanted to, actually specify it in your transfer CGI. For example, this:
Destination uic.edu.1139051993
is for my entire site ... it's my site handle. Whereas this:
Destination uic.edu.1991288441
is for a division within my site ... but it's impossible to tell the difference between "site" and "division" from just the handle (I mean, if I didn't say "this is a site" and "this is a division", there'd be no way for you to know). So when I look at your creds and permissions on your debug page, I can't quite tell if they give you download access for your site, or for the specific division you want to fix. If you could open the debug page with your division as destination (or confirm that that's what we're looking at), it'd rule out some things.

I cant accese iitunes store? "unable to locate requested page please check your connection"

ok, today i installed itunes, i live in india....so after i insalled i dint open it!
i just reboot my laptop (windows 7, home basic)
k then as i on my lapton and itunes i imported all music..
when i click the itunes stores it dosent opens.
i just wait... but after tat it shows "unable to locate requested page please check your connection"
dah!... why? please answer me!

Close your iTunes,
Go to command Prompt -
(Win 7/Vista) - START/ALL PROGRAMS/ACCESSORIES, right mouse click "Command Prompt", choose "Run as Administrator".
(Win XP SP2 & above) - START/ALL PROGRAMS/ACCESSORIES/Command Prompt
In the "Command Prompt" screen, type in
netsh winsock reset
Hit "ENTER" key
Restart your computer.
If you do get a prompt after restart windows to remap LSP, just click NO.
Now launch your iTunes and see if it is working now.
If you are still having these type of problems after trying the winsock reset, refer to this article to identify which software in your system is inserting LSP:
iTunes 10.5 for Windows: May see performance issues and blank iTunes Store
http://support.apple.com/kb/TS4123?viewlocale=en_US

For some reason the Apple ID window in iTunes and App Store now seems to have a character number constraint. As a result I am unable to enter the final few characters of my Apple ID which I have had for many years. Does anyone know what has caused this?

For some reason the Apple ID window in iTunes and App Store now seems to suddenly have a character number constraint which prevents me using my 29 character Apple ID. As a result I am unable to enter the final few characters of my Apple ID which I have had for many years. Does anyone know what has caused this?

You need to ask Apple for assistance with getting back into your old ID. To do this, click here and pick a method; if that page doesn't list one for your country or you're unable to resolve this issue through the Account Security team, fill out and submit this form.
(118441)

CUCM OS Administration Page Not There in CUCM 8.6

No option for CUCM OS Administration Page in navigation menu in CUCM 8.6
Unable to access CUCM OS Administration page.
following error came while using url http://<ip-address>/cmplatform
HTTP Status 404 - /cmplatform
type: Status report
message: /cmplatform
description: The requested resource (/cmplatform) is not available.

Try restarting tomcat
Also please post in the right forum, this one is for video over ip
Sent from Cisco Technical Support iPad App

Unable to enter text in text area box

Hi all,
I have an issue. unable to enter comments in the text area in the client side application while i can able to enter from my system. But when they login and logout they can able to enter.
When they again comeback to the page they could not. It is very difficult to logout everytime.
Is it a browser issue or any text area functionality?
Browser is IE
apex version is 4.0
can anyone please help?
Regards
Raj.

RajEndiran wrote:
Hi all,
I have an issue. unable to enter comments in the text area in the client side application while i can able to enter from my system. But when they login and logout they can able to enter.
When they again comeback to the page they could not. It is very difficult to logout everytime.
Is it a browser issue or any text area functionality?
Browser is IE
apex version is 4.0
can anyone please help?
Regards
Raj.Wrong forum.
Entering information into a form has nothing to do with SQL or PL/SQL.
Try the apex forum: Oracle Application Express (APEX)

Unable to enter text in popup window

Hi,
I am new to OATS OpenScript. I am unable to enter text in the popup window.
Here's my situation in detail:
My application is in Oracle Siebel and the pop up is a webpage dialog.
When I click on the Button in Siebel application, the webpage dialog pops up and there is a text box and a Submit button.
When I was recording, I was unable to record the webpage dialog as it was not identified by Openscript recorder.
Hence, I recorded the webpage seperately and the standalone scripts runs fine. It is able to navigate to the page and enter the text in textbox and click submit button.
Now I am trying to integrate those Webpage XPath in my existing script but it fails to recognize the webpage or the textbox from the popup webpage dialog.
Has anyone able to figure out how to record the popup windows using OATS OpenScript? Please help.
Thanks,
Sapna

Hi Deepu,
Thanks for replying.
web:window[@index='0' or @title='Enter Card Number']/web:document[@index='0']/web:body[@index='0']
web:window[@index='0' or @title='Enter Card Number']/web:document[@index='0']/web:input_text[@id='txt_name' or @name='name' or @index='0']
web:window[@index='0' or @title='Enter Card Number']/web:document[@index='0']/web:input_submit[@name='submit' or @value='Submit' or @index='0']
These are the XPaths I get when I record that webpage seperately.
Also when I was recording the webpage alongwith the siebel app, I got these XPaths for the same objects:
/web:dialog_unknown[@text='Enter Card Number -- Webpage Dialog' and @winClass='Internet Explorer_TridentDlgFrame' and @index='0']/web:accText[@index='2']
Submit Button
/web:dialog_unknown[@text='Enter Card Number -- Webpage Dialog' and @winClass='Internet Explorer_TridentDlgFrame' and @index='1']/web:accPushButton[@index='0' or @name='Submit']
I also read in one of the forums that if the object is not added, I need to add it manually. How can i do that?:
Popup wb window is not detected by openscript
Thanks,
Sapna

Can't Access the web administration page

Hello,
I have a new Linksys router that I installed a few months ago. I am trying to connect my PS3 using wireless. the PS3 sees the access point SSID, but keeps failing to connect. I have double/triple check the WEP2 key and it is correct. I am also having problems accessing the web administration page. I keep getting page not found. I don't think that I have access the web administration page since I set it up. I can ping the router, so I know that its up, along with getting out to the Internet, I have used NMAP and scanned the router, but only 10080 is open (PS3) port. I assume that the default URL for the web administration page is http://192.168.1.1. There is no port needed to put in the URL is there? Also, since NMAP showed no ports open does that mean that the web server in the router is not listen? If so how do I connect without having to reset the router?
I do have some Cisco Linksys app that shows a GUI of my network, but no adminisration help.
Thanks,

Who is your ISP..?
Are you able to go online on the wired computer...?
Make sure the computer is connected to the router on the Ethernet port and check the ip address first...Click Start >> All Programs >> Accessories >> Command Prompt...A black box will appear(Command Prompt)...In the Command Prompt window type ipconfig and press 'Enter'...Look for Ethernet Adapter Local Area Connection IP Address , Subnet Mask and Default Gateway...
IP Address should be 192.168.1.x, Subnet Mask : 255.255.255.0, Default Gateway : 192.168.1.1 (assuming your router is 192.168.1.1)...
If you get the above mentioned IP Address, Subnet and Gateway Address then you should ping the Gateway, type ping 192.168.1.1 and press Enter...If it gives you request timed out then disable any firewalls, security softwares on the computer...
If you get 4 replies then,Adjust the browser settings....Open an IE, click Tools >> Internet Options, then delete all files, cookies, history, forms...Goto "Connections", make sure Never Dial a Connection is checked, click on LAN Settings and make sure all the options are unchecked...Once you are done click on O.k...Close the IE and re-open it...
Now,try to open the setup page again...

Unable to enter Agent name and port details while doing ODI (11.1.1.6) installation on Solaris

Unable to enter Agent name and port details while doing installation on Solaris, Installation wizard is moving slowly and at 'Specify Agent Details' page it is not allowing me to enter the details and now I am not able to continue installation.
Please let me know if I am missing anything and there is any solution.

just in case cross verify the certiication matrix for 11.1.1.6
http://www.oracle.com/technetwork/middleware/data-integrator/odi-11gr1certmatrix-163773.xls
Thanks,
Saichand

NAS NSS 326 Reset Issue.

Hi peeps
Have a little issue with a Cisco NAS NSS 326 Smart Storage 6 bay - with RAID 5 over 6 disks.
Apparently there were some funny business with the performance with the device so someone reset the device from the button on the back.
I've been ask to get everything working but I've bumped into a little problem.
The DHCP address the device pick up is 10.2.7.127, so I open up a web interface and hop on that address and configure password, time etc.
When it comes up to step 6 I've tried selecting "Do not set disk configuration" and RAID 5, then on the finish window to start installing it advises it'll format all disk to continue!!!
We have a lot of data (9GB or so)
Is it possible to continue in any way without clearing the data we have on it? or map it somehow to recover the data?

Marc,
I would first back all data you wouldn’t want to lose since the volume is unlocked now. Instead of a hard reset we can attempt a reset of admin password. Administration guide: PG- 39
http://www.cisco.com/en/US/docs/storage/nass/csbcdp/smart_storage/admin/guide/NSS32X_Admin_Guide_OL21155_v1.5.pdf
Reset Network Settings and Password
You can restore the network settings and password for your NAS device using the
reset button located on the back panel. The NAS device should be powered on for
this procedure. Using a paper clip, press the reset button for 3 seconds, until the
NAS beeps.
The following settings are reset to default:
• System administration password: admin
• Network settings:
- Obtain TCP/IP settings automatically via DHCP
- Disable Jumbo Frame
- System management port - 8080
• System tools: IP filter settings - Allow all connections
• LCD panel password: (blank)
This 3 second reset should only clear out these fields but back up all data as a precaution.
Hope this helps,
Jasbryan.

OS X Lion and NSS 326

I've got a Cisco NSS 326 NAS and have recently run into a problem with OS X Lion Developer Preview and authentication to the NAS. When connecting to the NAS over AFP as guest I can access the NAS just fine. However, when I try and authenticate I get an error that reads:
"The version of the server you are trying to connect to is not supported. Please contact your system administrator to resolve the problem."
I've read on another site (http://trick77.com/2011/02/25/afp-broken-linux-based-nas-mac-os-x-lion-10-7) that this has to do with the version of AFP that is running on the NAS compared to the new version that OS X Lion is using AFP 2.
Does anyone have a solution to enable the NAS to support AFP 2 or are there any plans to support this from Cisco any time soon?

Hi all NSS32x owners,
Like you all, I bought a Storage Solution from Cisco, personally hoping that Cisco would be better in supporting us than the OEM they bougth the NSS32x line from.
Until now I have been disapointed over and over.
They opened a discussion about what should be implemented in the Cisco versions of the NAS'ses but so far no real addition of any value.
Now we are facing the problem with OS X Lion's TimeMachine incompatability, which could have been solved for months ago, when the first developer releases were issued.
No response from Ciso however.
This is really bad.
Other companies already have solutions for their products in order to be compatible with Lion.
Ok, I agree, this might not be a problem caused by Cisco, but a problem that was caused by Apple when releasing Lion. But hey all companies have to update their software so Cisco as well as Apple.
However, companies of major size (Apple, Cisco, and many others) should be more cooperative when releasing new software.
I work in IT for over 30 years now and I have always seen that when Cisco bought a company, their "boxes" were painted gray and the Cisco "bridge" logo was aplied and then all over sudden it became a REAL Cisco product.
And I mean it really became a Cisco product. You might have some minor problems but those were always solved.
I would have expected the same from Cisco with respect to these NAS'ses.
And believe me, I have seen quit some NAS'ses from the competitors but the NSS32x series does not come with the support you get from other competing NAS vendors.
That is what bothers me and I regret that there is no solution today for the issue(s) we have with OS X Lion, but what bothers me even more is that Cisco is not informing us at all about whatever solution there will be within whatever time frame.
I still have the NSS326 and I had to pay quit a premium over other vendors, but accepted it, supposing that the NAS would have the support I am familiar with from Cisco, but as you can read above I am disapointed.
So Cisco, what are you going to do to improve support and be more open and informative about coming software releases for the NSS32x series NAS'ses?
Regards,
Klaas de Jong

Setting portlet admin preferences without opening its administration page

In ALUI 6.5 , I would like to have a link inside a portlet, clciking which opens a pop-up window. Providing data and clicking save in the popup should save the data in portlet admin preferences and close the popup. Is there any way to achieve this?
We are able to set admin preferences for a portlet only from the Portlet Administration page which opens up on clicking the pencil icon in the title bar of the portlet. Clicking Edit button in the portlet administration page opens up the popup where data can be entered and saved in the admin preferences. We are looking for a way to be able to set the admin preferences without actually having to go to the portlet administration page.

Just to clarify, you want to click a link in the portlet to open the admin pref's instead of clicking the pencil?
To do that: grab the link URL from your web service: Advanced URL Settings: Remote Configuration Settings: Administration Configuration URL and then put it into your portlet.
If you want to have the admin preference code within the portlet I'm pretty sure you can just open up the the code that the admin configuration URL is pointing to and copy it into your portlet code and that should do the trick also.
Here is the 10.3 documentation dealing with Administrative Preferences (it shouldn't be very different from the 6.5 code base): http://download.oracle.com/docs/cd/E13158_01/alui/wci/docs103/devguide/con_portlets_prefspages_admin.html
user13820683 wrote:
In ALUI 6.5 , I would like to have a link inside a portlet, clciking which opens a pop-up window. Providing data and clicking save in the popup should save the data in portlet admin preferences and close the popup. Is there any way to achieve this?
We are able to set admin preferences for a portlet only from the Portlet Administration page which opens up on clicking the pencil icon in the title bar of the portlet. Clicking Edit button in the portlet administration page opens up the popup where data can be entered and saved in the admin preferences. We are looking for a way to be able to set the admin preferences without actually having to go to the portlet administration page.

Unable to enter administration page of NSS 326

Similar Messages

Maybe you are looking for