Unable to Execute a Report to send PAN XML messages out of SNC

Hi All,
We are unable to Execute a Report /SCA/DM_TIMESERIES_OUT to send Product Activity Notifications in the form of XML messages out of SNC. We have manitained some Planned Reciepts data in SNC and would like to transfer it out to ECC.
Could anyone help in understanding if we have to maintain mandatory settings before executing this report.
Thanks & Regards,
Sadiq

Hi Pravin,
As per the documentation(http://help.sap.com/saphelp_snc70/helpdata/EN/48/6bdb4767a431cbe10000000a42189d/frameset.htm), we have tried both the manual and automatic features to configure the output from SNC in the form of XML messages.
The manual method gave a message "Time series data for selection is empty" and the Automated method could trigger the XML messages on every incoming message from ECC but we are unable to see the Planned Receipts in that XML messages.
Was just wondering if we can see the Planned Receipt info by changing the settings of this report or by using any other simillar report as the PR info is very important for our development.
Thanks & Regards,
Sadiq

Similar Messages

  • Settings required to send ROEMPROACT2 XML from ECC to SNC

    Hi All,
    Can anyone explain the config that will be required on ECC / PI / SNC to send ROEMPROACT2 XML from ECC side and recevie the PAN XML successfully on the SNC side.
    I already went through this link : Using ROEMPROACT2 but couldnt understand.
    Also what transaction to use to check if the XML has been sent out successfully from the ECC system (Like we use WE05 for the Idocs)
    Thanks,
    Bharath

    Hi Bharath,
    In ECC you need to maintained the PI logical system in transaction SXMB_ADMIN.
    In PI you need to mapped XML mapping <ECCLogical_system>|ProductActivtyNotification_Out|<SNC_Logical_System>
    In SNC you need to maintain ProductActivityNotification_In XML configuration(By default this setting will be there) if it is not maintained then:
    Go to SPRO>Supply Network Collaboration>Basic Settings>Processing Inbound and Outbound Messages>Process Types for Inbound Messages-->Assign Inbound XML Messages to Default Process Types
    XML Message=ProductActivityNotification_Inbound
    Process type=Supplier Collaboration.
    Go to transaction code SXMB_MONI or SXI_MONITOR to check XML message in ECC.
    Regards,
    Nikhil

  • Sending an XML message and using proxy at receiver end

    hi all,
    please suggest me the steps to be followed in order to send a XML message and accepting this message using proxies.
    please help me out with detailed procedure.
    thanks+regards,
    Ujwalkumar

    Hi UjwalKumar,
    Follow this link:
    /people/prateek.shah/blog/2005/06/14/file-to-r3-via-abap-proxy
    This blog gives an excellent description of 'FILE to Proxy' scenario.
    what you need is XML to proxy...i.e. your scenario is very similar to this one...only diffrence is  that  , you wont be using FCC .since your source msg is in XML format..
    Hope this helps..
    Regards ,
    Sushil

  • I just upgraded my iPhone4s to iOS7 and now I am unable to make phone calls and send/receive text messages. Network signal indicator on the upper left side of the display shows hollow circles instead of full circles. Any idea how to fix the problem?

    I just upgraded my iPhone4s to iOS7 and now I am unable to make phone calls and send/receive text messaes. Network signal indicator on the upper left side of the display shows hollow circles instead of full circles (but with the network provider name). I checked with my colleagues in the office who use the same network and theirs work just fine on iOS7. Any idea how to fix the problem?

    I have also called my service provider and my service remains active in the network. I tried removing and reinserting my SIM but to no avail.

  • Unable to execute the report.  2108: The object requested: doest not exist in repository

    <BR>Hi,<BR><BR>I have developed report and saved . when I tried to execute from Hyperion reports web URL . It is giving me the error . The object requested does not exist in the repository Error No 2108.<BR><BR>can any one help me in resolving the isssue<BR><BR><BR>tx in advance for the help<BR><BR>regards<BR>bheemesh<BR>

    There might be a number of reasons why your report doesnt open up .One of the main reasons is that your report is incorrectly configured for the server and application .If you think that it is correctly configured .Then try exporting the report and then delete the report from the repository and then re-import the report back to the repository and check the server/application configuration and then run ur report again on the web . You should do fineeeeee.Naveen

  • Unable to execute the Report

    Hi All,
    There is issue, pls help me , when i am executing VL06 in foreground it is working properly and when i am executing in background for the same data system is showing no list (No Output)
    What may be the possible reason? pls help me in wayforward
    Regards

    Hi,
    i dont know whether you understood my query perfectly or not?
    i am trying to execute a query...
    if i execute in English, it says "No texts were maintained in language E for variable"
    but if i execute  the query in client's Language, its executing perfectly..
    i dont see naything in SE63, pls be more clear
    so please advice on this
    regds

  • Can someone help me send a text message out there

    I cant figure out how to send

    Press the green SMS button on the home page.
    Press the little box with the pencil in the corner of the screen.
    Type in the phone number next to the "To:" or press the "+" to use your contacts (then select a contact).
    Type your message.
    Press "send".

  • Configure the file adaptor so as to send sample XML message to integration

    Hi all ,
    I am totally new to XI.
    I had done the configuration and now i want to test the scenario but i dont now how to do that .
    please help me out how to do it.
    its an urgent.
    Thanks,
    shuja

    Hi,
    I think you should post your question Process Integration (PI) & SOA Middleware.
    Regards
    Message was edited by:
            Shehryar Khan

  • Send Receive xml messages

    Hi all,
    I want to find the best way to exchange xml messages with third party system (eg DI Server,  B1iSN).
    Thanks,
    Vangelis
    Edited by: Vangelis Kanellopoulos on Oct 9, 2010 5:34 PM

    I use XML Island on the Browser end.
    Browser
    <XML id="xmlDSO"></XML>
    xmlDSO.async = false;
    xmlDSO.load("Source.xml");
    /The source could be jsp as well but it should return xml in html/text format. SHould not have any HTML tags.
    Do the processing using IE XML
    Then
    <FORM>
    <INPUT NAME=xmlFIELD>
    </FORM>
    In
    function subForm() {
    form.xmlFIELD.value = xmlDSO.xml
    form.submit()
    In the servlet you should be able to receive the xml in a String.
    Which you can process.
    I have go so far as the getting XML into DOM.
    But I started getting into problem once I started using XPATH on the DOM.
    XPATH only takes Node as input. I need to get the DOM so I can start passing the NODE.
    If you don't need to use XPATH, you should be able to get to the stage where I am.
    -Krishna

  • Authorization problem to execute a report through portal

    Hi All,
    One of user while trying to execute report through portal, getting error message saying that
    "you are not authorized to execute the report XXXXXXX'
    Can not load query <query name> (data provider <data provider name> No authorizations for requested service.
    The report is a web template which is getting executed through portal.
    User is having all the authorizations to execute the report(report autho as well as infoprovider autho also)
    we have regenerated the user roles , done user comparision....every thing is OK.
    Still unable to execute the report.
    Please advice what can be done in this case....
    Regards

    Hi Shaik,
    Are you able to run this report with your user id?
    If so check the role or authorization objects which are missing to the user.
    And also check whether he got portal roles assigned to his profile.
    Regards,
    Ravi Kanth
    Edited by: Ravi kanth on May 12, 2009 2:06 PM

  • TSV_TNEW_PAGE_ALLOC_FAILED  error while executing the report

    Hi all,
    . We are having an info cubeXFIAP_C12 (FIAP: Vendor Line Item Open).In which we have defined 10 Dimensions and 6 Line Item Dimensions. We have created a report  on this with Key date as Input Variable Which gives me From Start to Till Date data. Also have an Variable on company code.
    Then No of Records in my Cube is 45, 70,624.Compressed the Info Cube data .But No aggregates on it.
    Now when I provide the key date as 30.06.2011 and Company code =XYZ.
    I am unable to Execute the Report, It gives me a short Dump. Saying NO ROLL MEMORY.
    Variables:
    1. Key Date:  Is a  Customer Exit variable .If user Enters Data as 30.06.2011 ,It fetches data from     u201C00000000u201D to u201C30.06.2011u201D.
    2.Company code: Is a Manual Entry /Default variable.
    I also have shot dump.Please find the error analysis of dump below:
    The internal table "\FUNCTION-POOL=RRK0\FORM=MEGA_SORT_M\DATA=C_TSX_SORTK[2]-GT
    ABIX[1]-GTABIX" could not be further extended. To enable
    error handling, the table had to be delete before this log was written.
    As a result, the table is displayed further down or, if you branch to
    the ABAP Debugger, with 0 rows.
    At the time of the termination, the following data was determined for
    the relevant internal table:
    Memory location: "Session memory"
    Row width: 4
    Number of rows: 1503307
    Allocated rows: 1503307
    Newly requested rows: 2048 (in 1 blocks)
    can any one help me .......
    Regards
    Laxman

    Hi,
    Just check following things
    1http://help.sap.com/printdocu/core/Print46c/en/data/pdf/BCCSTMM/BCCSTMM.pdf
    2. See whether any back up process is happening and it has consumed the main memory.
    3. Are you getting this error regularly
    4. See any transport went and compression/aggregation got removed.
    5. Check whether there are many dumps in ST22 same time when you execute report
    http://www.sdn.sap.com/irj/scn/go/portal/prtroot/docs/library/uuid/4ab89e84-0d01-0010-cda2-82ddc3548c65?QuickLink=index&overridelayout=true
    6. http://www.sap-press.de/download/dateien/1049/sappress_bw_performance_optimization_guide_080.pdf
    7. Check whether Infoprovifder got removed from BIA
    8. Query removed from BIA post transport
    9. Run RSRT and regenerate the report.
    Thanks and regards
    Kiran

  • Message "No applicable data found" after executing the report

    Hi all,
    I have 60 records in a cube which is extracted from a function module. I am able to see the data in the cube but when I execute the report I am getting the message u201CNo applicable data foundu201D. Why is that so?
    Can any one please explain me what to do to bring data when the report is executed?
    When I execute the query there is only one field selection criteria 0P_FPVANT and this is mandatory. When I checked the data in the cube I didn't find any field 0P_FPVANT but I found a field Fiscal Period Variant with the technical name, 0FISPER
    I executed the query in RSRT and there also I am getting the same message, "No applicable data found".
    Please advise what do I need to do inorder to get data when the report is executed?
    Thank you.
    Regards,
    Pavan.

    I think so.
    Ok let me take the other report 0FIAR_C02_Q1003. For this report the selection criteria is
    Company code,
    Customer and
    Period/Fiscal Year
    Of these only company code is mandatory. In the data in the cube I see that for co. code BP01 data is available. So I executed the report with co. code as BP01 but no data.
    Then I gave co. code BP01 and Period /Fiscal year as 2008, 2008.03, still I see no data.
    I tried with values in all the fields that are available in cube
    co. code - BP01
    Customer - PCS-C10
    Period/Fiscal Year - 2008011
    Now with respect to Period/Fiscal Year selection field in report, in cube there are 4 columns
    Fiscal Year Period,
    Posting Period,
    Fiscal Year Variant and
    Fiscal Year
    I've tried all of them but when I enter values in all the fields still I am getting the same error, "no applicable data found".
    Please advise.
    Thank you.
    Pavan.

  • Need of XI to send an XML from one SAP system to another SAP system

    Dear colleagues,
    I work in the SRM solution.
    In SRM there is a Purchaser and Supplier scenario called Supplier Self Services.
    The Purchaser creates a Purchase order and sends it to the supplier in form of an XML file.
    The purchaser system and supplier system are the same SAP system but different clients.
    Example: Purchaser client is 300 and Supplier client is 330 and both of them are on the same system.
    I have a very basic question.
    Currently we have the XI system which acts as an interface to send the Purchaser PO XML to the Supplier as XML.
    a)My question is in case the XML structure is identical across both the clients, then what is the need of XI system?
    b) Is it not possible to send XML from one client to another without an XI system? there si no need of any message mapping required since I am expecting the same XML structure in both clients.
    Please clarify the need of XI system in the following scenario. Is it not possible without XI?
    Many thanks.
    Best regards,
    Srivatsa

    Hi Srivatsa,
        YOu can send the XML message from one sap system to another sap system even without an XI system in between.
    But the use of SAP XI (Or any other middleware) is recommended because, it gives you the following advantages.
    1) Better monitoring and alerting mechanism. XI provides you robust set of tools that let you monitor the status of the messages that are exchanged.
    2) Direct communication between systems is referred to as Point to Point communication, which has its own disadvantages as against Hub and SPoke model (Message exchange using XI).
    3) Message delivery is guaranteed if you have XI in between.
    If the target system is down, the sender sap system will not try multiple times to post the message.
    But if you use XI, it can be configured to send the message multiple times, till it succeeds.
    Regards,
    Ravi Kanth Talagana

  • [HTTP Sender]How to send different XML using static URL

    Hi all,
    I have a problem, my legacy system send XML messages to SAP XI by HTTP, I know that I need to use HTTP Sender adapter, the problem is that legacy system support only a static URL. I have more than one interface, how could I fix this problem?
    Can I send the XML message to SAP XI without define INTERFACE on URL? How can I handle this?
    Thank in advance,
    Daniel Torres

    Hi Srinivas,
    The legacy system is a java application, that send XML messages to SAP XI server using HTTP protocol. So I just ask to legacy system team to change the application to add <b>server</b>, <b>namespace</b> and <b>interface</b> attributes to the URL querystring.
    So for each XML message you should especify mesage interface that it belongs to. You do it by especifying on URL as message atribute for exemple:
    HTTP://[SAPXISERVER]:80[SYSTEM ID]/sap/xi/adapter_plain?service=[BS SERVICE]&namespace=[MESSAGE INTERFACE NAMESPACE]&interface=[MESSAGE INTERFACE]
    So if you have for example information belows:
    <b>MESSAGE INTERFACE</b> = MI_MYMESSAGEINTERFACE_IB
    <b>MESSAGE INTERFACE NAMESPACE</b> = urn:teste:mymessageinterface
    <b>SERVICE</b> = MY_LEGACY
    <b>SYSTEM ID</b> = 10
    <b>SAPXISERVER</b> = MYSAPXI
    Your url should looks like: http://MYSAPXI:8010/sap/xi/apadter_plain?service=MY_LEGACY&namespace=urn:teste:mymessageinterface &interface=MI_MYMESSAGEINTERFACE_IB
    You should have a different message interface for each XML that you send to SAP XI.
    Message was edited by:
            Daniel Torres
    Message was edited by:
            Daniel Torres

  • Send XML messages via Internet

    Hello,
    Just wanted to know if it is possible for SAP R3 Enterprise 470x110 to set this up.  Basically we wanted to send XML messages over the internet to our counterparts in other location.  In return they will be sending us XML messages in return that we need to process.  Is this a limitation of our SAP release?  If this can be configured in our system, does anyone has done it?  Let me know if you have references. 
    Thanks a lot.
    Tony

    Jan,
    if QoS is important to you then JMS may not be overkill. Most appservers like Borland, IONA, HP/Bluestone and BEA provide JMS facilities already. What appserver are you using? Does it support JMS?
    There are many cases of companies doing what you want to do, both internally and externally with their partners over the Net.

Maybe you are looking for