Unable to start in single-user mode - HD dead?

My MacBook Pro (Mac OS X) refused to start, it hung up on the loading screen where you see the apple and the spinning loading wheel. I found out how to fix this, I had to go into single-user mode and type "/sbin/fsck -fy" to repair/verify the disk (I was unable to do so from the Disk Utility via the Install Disc, the repair/verify buttons were just grayed out).
Anyways, doing this from the command line (single-user mode) fixed the problem and I could boot into Mac OS X (there were more issuses after this point which forced me to do an "Archive and Install").
^ that happened a week ago. And happened again yesterday, hung up on the exact same point. So I boot up my Mac into single-user mode, and type in "/sbin/fsck -fy" to start the process. Different from last time, I got a lot of text this time. It also kept going for a longer while. After about 10 minutes, there was a couple of minutes where nothing happened. So I typed "/sbin/fsck -fy" again (as I'm supposed to do so until it says "** The volume (nameofvolume) appears to be OK"), and I got some more text, then nothing happened for a while.
Inpatient as I am, I considered the process to be complete, and restarted my Mac by typing "exit".
I think I ****** up my Mac OS X partition at this point. Because when I try to start my Mac now, it automaticly boots into Windows XP (my other partition). Also I cannot enter single-user mode or Verbose mode, the Mac just ignores and goes right into Windows XP.
I've tried to boot from the Install Disc. When I run Disk Utility, the "HD"(name of Mac OS X partition) is grayed out. I can't do an Archive and Install because it cannot detect my main partition.
An interesting thing though: When I have the Install Disc inserted, I can enter single-user mode (by holding cmd+s at startup). However, when I type /sbin/fsck -fy, it starts verifying the Install Disc rather than the HD.
Also when I open My Computer in Windows XP, I can see the other partition (MacDrive). When I select it, I see:
Free Space: 219GB
Total Size: 168GB
This indicates that my HD is dead/erased, and that my last three months of work is gone. This just because I'm impatient, and didn't wait for the fsck process to complete.
What is the next step? How can I get into single-user mode so that I can verify/repair my disc?

On the point of contacting the folks at Alsoft, I have found that they seem to be unobtainable on www.alsoft.com at present.
I wanted to get in touch as I had a small problem with Diskwarrior on updating to 10.5.5 from 10.5.4 ,
Disk permissions ends with an error code.
I wonder if there were so many queries re this that they are unobtainable?
I run 3 machines from a wireless router, an iMac, an HP laptop with XP and a totally obsolete Dell into which i have squeezed W2000, with a resultant mix of browsers but no contact with the folks at Alsoft.
Am I in a minority of one here?

Similar Messages

  • MBP only runs if I start in single user mode and run fsck. WHY!

    I am having trouble with my MBP. If I don't start in single user mode and run fsck -fy twice, I can't click on anything with my trackpad. I can't even log in. I've tried resetting pram/nvram, disk permission repair too but once i reboot... nada. I can't do anything in recovery mode, I can move around with arrows and tab but can't select anything. Safe mode hangs at about 20% and doesn't budge (left it for an hour, nothing). If I run fsck -fy it works but as soon as I reboot/ logout i'm back to square one again. Anyone know what causes this to happen? It just started tonight. I have a 2012 15" with Mountain Lion.

    The boot drive is failing, or you have some other hardware fault.
    Back up all data immediately, then make a "Genius" appointment at an Apple Store to have the machine tested.
    If privacy is a concern, erase the data partition(s) with the option to write zeros* (do this only if you have at least two complete, independent backups, and you know how to restore to bare metal from any of them.) Don’t erase the recovery partition, if present.
    *An SSD doesn't need to be zeroed.

  • What's   "...start in Single User  mode"? HOW? and WHY?

    A silly question...
    What's "...start in Single User mode"? HOW? and WHY?
    Can anyone, please explain that to me?
    Cheers!

    Hello Nando,
    The only silly questions are the ones that never get asked
    Have a look in here...
    Single User Mode
    Hope that helps
    Regards
    Ian

  • Impossible to boot MacBook Pro Retina ! impossible to start in single user mode, Openfirmware password set, but safari works!

    I have got a Macbook pro retina.
    I have done 2 partitions on the SSD drive. 1 for the OS and 1 for the user (with a kind of ln -s /Home/myself /Volume/Part2/myself
    I was watching a movie (with VLC) in full screen for a while and I wanted to escape. Impossible, and impossible to reboot.
    When I start, I have a directory with a question mark.
    I have a Open firmware passwords set (that I remember).
    I cannot reset PRAM. (I can not change the RAM amount inside the commuter as this is a retina model)
    I cannot start in verbose mode.
    I can choose a disk to boot. I see only the OS drive and not the user partition, and no 'recovery partition'. It seems that i need to do a fsck -yff on the user partition but how ?
    I can start the OS partition, and i can choose 'guess' or 'myself'. If i choose myself, I have an error message :'there is a error, the session can not start'. If I start with the guess account, I restart, and then I can browse the internet with safari (this is how I am writing this text!)
    => How can i repair the partition ? (open a terminal, boot in single user mode ...?)
    best regards.

    Actually, the recovery partition was there, but was not shown as my user partition. I have seen that reseting the PRAM and changing the ram could remove the open firemware password. So i have turn the computer on until the battery was empty. Then I boot about 20 times, and unplug the power supply after few seconds at different step of the booting pricess. At last, the screen default resolution when booting changed, I undertood that i succeeded, and I was able to enter.
    Then I boot in single user mode, removed the open firmware password, activated the root user,  and everything was fine now !

  • Can't start in single user mode, trying to fix blue screen startup

    Trying to fix my blue screen startup and I'm on the step to fix the Network Preferences and I'm suppoed to go into single user mode. It starts but then locks up. last line is: localhost:\ root# Anyone have an idea?

    Hi David.
    Sorry we haven't received any response yet. getting used to the new forum is occupying a lot of peoples time at present I fear. I've yelled a bit louder this time!
    In the mean time, have you already tried starting up in SAFE mode, rather than SU? http://docs.info.apple.com/article.html?artnum=107393 and following the other processes identified in http://docs.info.apple.com/article.html?artnum=106464
    If you have access to another firewire equipt Mac then you could also use Target disk mode (connect the two together with a firewire cable, then start up your own computer while holding down the t key. ) Your own HD would then appear on the desktop of the other computer as another HD, and you can then proceed to remove or shift the same .plist files (on your own HD) identified in point 4 or 5 of http://docs.info.apple.com/article.html?artnum=106464
    Cheers
    Rod

  • MacBookPro does not start in Single User Mode

    I am trying to boot my MacBookPro in Single User Mode. I read I should power off computer then start it while holding Command-S. I don't know what I am doing wrong but whenever I try, Mac just load normally and load the system.

    Nevermind, seems to be working now!

  • Macbook won't start in single-user-mode.

    I'm trying to repair the disk and instead of booting in single-user mode, it boots up regularly, ignoring Command + S. I'm running 10.6.8.
    Thank you.

    Nevermind, seems to be working now!

  • Latest Patch cluster (Feb 11, 2010) unable to run in Single user mode.

    Hi ,
    This is my first post in this forum.
    Hope you people will help to resolve the issue.
    My issue - I have downloaded the latest patch cluster (Feb 11, 20100) and tried to install it from single user mode.
    Nothing happened. I have waited for more than 30 mins, still no progres.
    Then I killed the process, and tried to run it in Multi user mode (To verify any issue with extraction or file) -- Its working(and killed the process) !!!
    Anyone facing this strange issue ?
    Appreciate your help to complete the patching.
    Thanks.
    sas.

    Hi,
    If you're encountering issues with a patch cluster bundle your best bet is to contact [email protected] From the description it sounds like there may be a filesystem not mounted in SUM that the cluster is trying to patch.

  • Single user mode locks up hard

    Is anyone else having this type of problem? I had it with both Panther and now also with Tiger. I've filed a bug on this with apple, but they closed it citing the usual "you have third party ram" argument. The ram has zero issues with anything else and I've done some very extensive testing of it (running remember for 72+ hours without a single fault).
    Basically what happens is within 2 seconds of getting the root shell prompt in single user mode it locks up. By lock up I mean that the keyboard is locked out and no method of input works. Funny enough if there was a key pressed down when this happens the key keeps repeating, even if I unplug the keyboard.
    This machine seems to be kind of haunted (have other problems with it as well, all registered with Apple) but I can't get them to replace it.
    Just looking to see if I'm the only one with this problem or not ....
    TIA

    Are you using a Bluetooth keyboard? Some people have reported being unable to type in Single User mode with a Bluetooth keyboard, even though everything else works normally.
    (8916)

  • How to get to single user mode

    I aquired an old power mac G4 with an old account with 10.3.9 and an old administrator account.  It seems that procedures to remove the account start in Single user mode.  The computer won't start when holding down system - s.  The drive clicks a few times but the display goes to sleep from no video signal.  So How can I get to single user mode when the usual way don't work?

    The hard drive's directory may be dead, or it may have last been booted into Mac OS 9.  IF you are lucky, they did install Mac OS X on it, and that can be determined either through an Option key boot, or through an X key boot on a wired (not wireless) USB Apple compatible keyboard.   X key booting will only work if the X operating system is on the same partition, whereas Option key boot will reveal the Startup Manager, where you select the drive and hit the right pointing arrow for the drive partition that has Mac OS X.   Note this will not work on an original PCI PowerMac G4.   You may also need to replace the PRAM battery, a 1/2 AA 3.6V battery from Radio Shack before any boot sequence will work.  Once it boots into Mac OS X, Single User Mode should work.

  • Restarts in single user mode since install

    Hi,
    I've only seen this problem on one of my computers. Since installing SL (from family disk), when restarting or starting from full shut down, the MBAir starts in Single User mode with command lines. I actually think it showed the GUI for about 2 seconds then goes into the command line text. Shows a bunch of the usual stuff about MAC framework initiations and lines about kernel dependency. I don't see any error lines repeated (but I do not understand much of the code) and it does not offer me a prompt. After about 1 minute, it launches the OS X gui and everything else is fine.
    I updated the 10.6.1 - same problem persists.
    So far I've verified, repaired some permission, PRAM, and tech tools basic. Do I need to do some deeper investigating? Any ideas?
    Thanks
    bc

    bluecool wrote:
    Will do. Do you mean re-choose the start up disk from the sys pref? Why might it search for another start up disk?
    resetting PRAM clears the startup disk settings.

  • Mount USB Device in Single User Mode

    Hi All,
    Can anyone give me any assistance of mounting a USB stick in single user mode?
    I am trying to use the command:
    $ mount -uw /dev/disk2s1 /Volumes/usb
    But it get the error:
    --specified device does not match mounted device
    If I put the USB stick in normal OSX mode, then run 'df -k' in terminal, it is mounted by automounter, but I can't seem to get it to mount in single user mode.
    Thanks,
    Nik

    Hi Nik,
       I don't believe that there are enough services started in Single User Mode to do this; you'll have to start the services yourself. However, I haven't tested this so I don't know. Wanna be a Guinea Pig?
       If your going to need to write to the boot drive, mount it read/write with:
    /sbin/mount -uw /
    Next, start the basic services, including diskarbitrationd:
    /usr/libexec/registermach_bootstrapservers /etc/mach_init.d
    The above should be one line, modulo wrapping. Then start diskarbitrationd:
    /sbin/SystemStarter start Disks
    You should probably check /dev and see what disks are already mounted. (without the USB stick) I assume that the services that mount removable media are now started so insert the stick and see if it appears mounted in /Volumes. Otherwise, check /dev and see if there's a new disk. If it only appears in /dev, you can use the standard mount command to mount it. If it doesn't appear in /dev then you might reboot into Single User Mode and repeat the procedure with the USB stick already inserted. If none of that works then this must not be the right method and you have my apologies.
    Gary
    ~~~~
       Computers are like air conditioners. Both stop working
       if you open windows.
          -- Adam Heath

  • Can't exit single user mode

    I frequently start in single user mode to run fsck -fy on my startup disk
    and after running fsck -fy, I exit single user mode typing exit or logout.
    Now after running fsck -fy, typing exit or logout the single user mode remains
    and returns a line: -sh-2.05b#. I’m not adept enough to use single user mode
    other than for running fsck -fy so I am stuck on how to end the single user mode. TIA
    Eric

    Some stories have happy endings and this is one of them.
    After a little head scratching I dig out the Tiger install DVD
    and repaired the permissions on the problem HD partition.
    Reboot to the problem disk, enter correct network settings, and
    now we even have a web to surf. Also we can exit single user mode OK.
    Eric

  • Bluetooth errors (hundreds) in single-user mode

    Never had this in Tiger or Panther but...
    When starting in single-user mode I get hundreds of USB Bluetooth errors.
    Also all too often (approx. every other day) when rebooting I loose use of my Bluetooth Apple keyboard and have to use Leopard Cache Cleaner to clean the user and system caches... after which the keyboard is once again functional.
    Even though */sbin/fsck -fy* gives the system an okay after the hundreds of errors... I can restart and again get the same errors.
    Here is an image of what it looks like (a little blurry but if you're familiar with such errors perhaps you'll recognize them). If necessary I'll take another photo of the screen and post it.
    http://www.theimagecache.com/downloadarea/forum_images_misc/single_usererror.html
    Thanks for any advice on how to get rid of these errors once-and-for-all.

    A wireless bluetooth keyboard would only let you boot into Single User Mode, after that, you will need a regular USB keyboard to type in the prompts, same goes when doing a Hardware Test using the disc provided.
    As for some users posted on this forum saying they have not able to continue the Single User Mode under a regular USB keyboard, I am afraid I am one of them... I have not been able to solve the problem as yet and it is kinda "annoying" that there "may be something wrong" with my iMac that I cannot perform fsck, nevertheless I have regularly booted from the OS disc and run Disk Utility, which is equivilent to booting to SUM, but supposingly much better, and my HD checks out fine... so at the moment I have no worries.
    In my post there is another person who has regularly keeping me update about this problem and has deduced it maybe due to the internal bluetooth module and the USB inside... rather complex issue that may require me lengthy conversation with AppleCare or have something replace, or "worse" have my iMac sent away for a time for repair or replacement. Since my iMac is doing quite fine, I'll live with it for the moment...
    Cheers

  • Loud Fan Noice, Single User Mode?

    My iMac makes really loud fan noises when it's on
    There's no problem with it, but the fan is running all time and making loud noises.
    So I looked for help, and some say about starting in single-user mode.
    What exactly is it and what does it do to my computer?
    Is it really necessary?
    iMac G5 PowerPC   Mac OS X (10.4.9)  

    "what exactly do i have to do for disk utility test ?
    i verified and i checked those permissions stuff
    but i dont exactly know what i'm supposed to do there"
    Did you do the above from your Tiger DVD?
    If you received errors did you click the Repair Disk button?
    Were there errors that the Utility could not repair? If so, then you will need to use a stronger utility programs. The top 3rd party utility programs that are favorites/recommended in these forums are the following:
    DiskWarrior
    Highly recommended for *directory damage* repairs.
    TechTool Pro
    Multi-functional utility.
    Drive Genius Multi-functional utility.
    You will need to make your own decision on which to purchase. Read up on them on their websites because each does something a little different.
    ================
    If you did not repair from your Tiger DVD:
    Repairing permissions from the Tiger DVD
    Boot up from your Tiger Install DVD while holding down the "c" key.
    Select the language you wish to use, and then choose "Disk Utility" from the menu bar.
    Your HD should appear in a panel on the left hand side of the window which opens. Select it and then click on the "repair disk" button in the right hand section of the window.
    If Disk First aid is able to complete the repair now click on the "Repair permissions" button.
    Once this process has been completed restart your computer.
    http://docs.info.apple.com/article.html?artnum=25751 About Disk Utility's Repair Disk Permissions feature
    TIP-You should Repair Permissions:
    After installing and/or updating an OS (Operating System).
    After installing software.

Maybe you are looking for