Updated bios via Live Update and now my Network card isn't detected

I have an msi Z87-GD65 Gaming Motherboard and I updated some drivers and the bios via msi Live Update 6 last night and now my computer refuses to recognize my network adapter. The adapter is a TRENDnet N600, plugs into PCIe if I'm not mistaken. Wifi if my only option with this computer, I can't use ethernet, so it's really important I get the network card working again. I have had zero issues with it until this.
The reason I was updating was to try to get my third monitor to work when plugged into the mobo, while my other two were plugged into the graphics card (which I also installed yesterday, but it's working fine). Note that it still was not working, but I had enabled the IGD Multi-Monitor from bios.
Any suggestions would be appreciated. I did try uninstalling the drivers but it still won't detect the network card. I also tried disconnecting and reconnecting the network card (and I cleaned the port for good measure).
I've only been using Windows computers for a year, so bear with me if there's stuff I don't know. Thanks in advance. I can try to get a full list of what was installed later tonight, but all of it that I can find has been uninstalled at this point.
Note: I did not flash the bios when I installed, which I have now heard is a bad idea, apparently. l:

what OS you are running?
Quote
Note: I did not flash the bios when I installed, which I have now heard is a bad idea, apparently. l:
you said you've updated drivers & BIOS:
Quote
I updated some drivers and the bios via msi Live Update 6 last night and now my computer refuses to recognize my network adapter.
can you clarify is you update BIOS too or not?
and what is your current bios version?
Quote
and I updated some drivers
what kind of drivers?
Quote
I did try uninstalling the drivers but it still won't detect the network card. I also tried disconnecting and reconnecting the network card (and I cleaned the port for good measure).
have you tried to load last good known configuration or the last windows restore point?
or to reinstall OS?

Similar Messages

My Apple TV stalled during an update and now just shows an image of it being plugged into a USB. It won't complete the update and does nothing when I plug it into my Mac via USB.

2 Apple TVs. The first won't reboot, it stalled during an update and now shows a picture of a UBS plug. Ive tried to plug into my computer, nothing happens. At a standtill.
The second Apple TV works but only if I send something via Airplay. The remote no longer has any affect. The light on the front of the Apple TV blinks when I push a buttom on the remote but nothing happens.
Any Ideas? I am starting to think I need to replace them. Thanks.

Ok, with itunes open on the pc, plug one end of the usb cord into the computer, but not connected to the ipad.
now, press the power button on the ipad until it turns off.
Then, press and hold the home button on the ipad at the same you plug the usb cord into the ipad. DON'T LET GO OF THE HOME BUTTON.
Keep holding the home button until you see the recovery mode message pop on the itunes window.
When that happens, you should now be able to restore.

HT201628 My girlfriend accidentally rebooted her iPod during an update, and now it won't boot. How can this possibly be fixed?? She says the OS has been wiped. You know how to fix this??

My girlfriend believes she's wiped out the OS on her iPod 4th generation she said she did this by accidentally rebooting her iPod during an update, and now her iPod just shows the apple logo then fades to white. My question is, can this be fixed? Or is a new iPod necessary??

If you live near an Apple store take it in for diagnosis. Don't forget to make an appointment online first. If you don't live near a store, you may get help by searching "youtube" for DFU Restore ipod. This is not difficult to do but it requires proper timing to get the device into DFU mode.

I thought I was installing an update and now iTunes will not open? HELP!!!!!, I thought I was installing an update and now iTunes will not open? HELP!!!!!

I thought I was installing an update and now iTunes will not open on my computer... HELP!!!!

Others are more likely to help if you stop needlessly repeating yourself and provide some details.
What operating system? Windows (XP, Vista, 7) Mac
Any errors?
Also, try doing a search either here or via Google, you are more likely to get a faster resolution as there is no need to wait on others to respond.

I recently did an apps update and now the update is locked and I have 15 apps I can't open. Any suggestions on how to fix this?

I recently did an apps update and now the update is locked and I have 15 apps I can't open. Any ideas on what may have caused this and to fix it?

If Ralph's suggestion doesn't work, try a Restore. Note that it's nowhere near as quick as a Reset. It could take well over an hour! Connect via cable to the computer that you use for sync. From iTunes, select the iPad/iPod and then select the Summary tab. Follow the on-screen directions for Restore and be sure to say "yes" to the backup. You will be warned that all data (apps, music, movies, etc.) will be erased but, as the Restore finishes, you will be asked if you wish the contents of the backup to be copied to the iPad/iPod. Again, say "yes."
At the end of the basic Restore, you will be asked if you wish to sync the iPad/iPod. As before, say "yes." Note that that sync selection will disappear and the Restore will end if you do not respond within a reasonable time. If that happens, only the apps that are part of the IOS will appear on your device. Corrective action is simple - choose manual "Sync" from the bottom right of iTunes.
If you're unable to do the Restore (or it doesn't help), go into Recovery Mode per the instructions here. You WILL lose all of your data (game scores, etc,) but, for the most part, you can redownload apps and music without being charged again. Also, if you have IOS-7, read this.

HT4623 By accident i removed the charger while updating and now my iPhone shows me connect to iTunes and i am but my Phone doesn't show Help :(

By accident i removed the charger while updating and now my iPhone shows me connect to iTunes and i am but my Phone doesn't show Help

You need to restore the iPhone via recovery mode. To do this follow the link below to guide you:
http://support.apple.com/kb/HT1808
Because you need to restore to factory settings all data on the iPhone will be erased. Because the iPhone was never backed up most of the data you won't be able to get back.

TS1362 just purchased new cpu ,windows 8 recieved new updates and now I Tunes not play when play button hit.nothing happens??Rsvp please .time is fleeting:)

just purchased new cpu ,windows 8 recieved new updates and now I Tunes not play when play button hit.nothing happens??Rsvp please .time is fleeting:)

RealPlayer can cause conflicts with Flash Player because it tries to assign EVERY TYPE of video or audio file to itself by default. I haven't used RealPlayer in years for that reason. It's an unnecessary program anymore. There are apps loike VLC media player that cna do EVERYTHING it does without conflicting with other apps like Flash Player.
With WIndows 8, Microsoft began embedding FlashPlayer themselves into Internet Explorer. Because of that, you cannot download and install it from here. You cannot uninstall it from Internet Explorer without removing a specific Windows Update first. And you cannot update it via this website. ONLY through Windows Update can Flash Player for Internet Explorer be updated.
That said, you probably DON'T have a virus that's causing the problems with Flash Player and Internet Explorer. Many, many websites are not "recognizing" the browser.
This is a known problem with Internet Explorer 11, which Microsoft has been aware of since October 18 when they released IE11 The pages can't recognize the browser, so they don't recognize any of the plugins, like Flash Player.
So far, Microsoft has made NO indication that they have any plan to fix it soon.
Microsoft's recommendation is to use Compatibility View for affected pages, and "pretend" you're using an different browser. Trouble with that is it has seen limited success at best, and you have to individually enable it for EVERY page that has problems.
I'm not big on "pretending" so I recommend actually using another browser.
Firefox (from Mozilla)
Opera (from Opera)
Safari (from Apple)
Chrome (from Google)
ANY of those will work where IE11 won't, with the Flash Player Plug-in (For all other browsers), and Chrome doesn't even need that because it has its own Flash Player plugin built in.

I recently downloaded the latest iTunes update and now my menus are in Korean. I work in Korea but want my menus in English. I've never had this problem with updates before. How can I get English back? Thank you.

I recently downloaded the latest iTunes for Windows update, and now when I open iTunes my menus are in Korean. I live and work in Korea but want my menus in English like they always have been. I've never had this problem with updates before. How can I get English back? I'll appreciate any help.

CTRL+, (Comma) brings up preferences
General is the tab on the left
Language is the last drop down control
English (UK) & English (US) are 9th and 10th on the list
Close iTunes & reopen to effect the change
tt2

Last night I did an update and now when I turn on my macbook it just goes to the white screen with the apple and stays like that.

Last night I did an update and now when I turn on my macbook it just goes to the white screen with the apple and stays like that. How do I fix this issue?

Take each of these steps that you haven't already tried. Stop when the problem is resolved.
To restart an unresponsive computer, press and hold the power button for a few seconds until the power shuts off, then release, wait a few more seconds, and press it again briefly.
Step 1
The first step in dealing with a startup failure is to secure the data. If you want to preserve the contents of the startup drive, and you don't already have at least one current backup, you must try to back up now, before you do anything else. It may or may not be possible. If you don't care about the data that has changed since the last backup, you can skip this step.
There are several ways to back up a Mac that is unable to start. You need an external hard drive to hold the backup data.
a. Start up from the Recovery partition, or from a local Time Machine backup volume (option key at startup.) When the OS X Utilities screen appears, launch Disk Utility and follow the instructions in this support article, under “Instructions for backing up to an external hard disk via Disk Utility.” The article refers to starting up from a DVD, but the procedure in Recovery mode is the same. You don't need a DVD if you're running OS X 10.7 or later.
b. If Step 1a fails because of disk errors, and no other Mac is available, then you may be able to salvage some of your files by copying them in the Finder. If you already have an external drive with OS X installed, start up from it. Otherwise, if you have Internet access, follow the instructions on this page to prepare the external drive and install OS X on it. You'll use the Recovery installer, rather than downloading it from the App Store.
c. If you have access to a working Mac, and both it and the non-working Mac have FireWire or Thunderbolt ports, start the non-working Mac in target disk mode. Use the working Mac to copy the data to another drive. This technique won't work with USB, Ethernet, Wi-Fi, or Bluetooth.
d. If the internal drive of the non-working Mac is user-replaceable, remove it and mount it in an external enclosure or drive dock. Use another Mac to copy the data.
Step 2
If the startup process stops at a blank gray screen with no Apple logo or spinning "daisy wheel," then the startup volume may be full. If you had previously seen warnings of low disk space, this is almost certainly the case. You might be able to start up in safe mode even though you can't start up normally. Otherwise, start up from an external drive, or else use the technique in Step 1b, 1c, or 1d to mount the internal drive and delete some files. According to Apple documentation, you need at least 9 GB of available space on the startup volume (as shown in the Finder Info window) for normal operation.
Step 3
Sometimes a startup failure can be resolved by resetting the NVRAM.
Step 4
If a desktop Mac hangs at a plain gray screen with a movable cursor, the keyboard may not be recognized. Press and hold the button on the side of an Apple wireless keyboard to make it discoverable. If need be, replace or recharge the batteries. If you're using a USB keyboard connected to a hub, connect it to a built-in port.
Step 5
If there's a built-in optical drive, a disc may be stuck in it. Follow these instructions to eject it.
Step 6
Press and hold the power button until the power shuts off. Disconnect all wired peripherals except those needed to start up, and remove all aftermarket expansion cards. Use a different keyboard and/or mouse, if those devices are wired. If you can start up now, one of the devices you disconnected, or a combination of them, is causing the problem. Finding out which one is a process of elimination.
Step 7
If you've started from an external storage device, make sure that the internal startup volume is selected in the Startup Disk pane of System Preferences.
Start up in safe mode. Note: If FileVault is enabled in OS X 10.9 or earlier, or if a firmware password is set, or if the startup volume is a software RAID, you can’t do this. Post for further instructions.
Safe mode is much slower to start and run than normal, and some things won’t work at all, including wireless networking on certain Macs.
The login screen appears even if you usually log in automatically. You must know the login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
When you start up in safe mode, it's normal to see a dark gray progress bar on a light gray background. If the progress bar gets stuck for more than a few minutes, or if the system shuts down automatically while the progress bar is displayed, the startup volume is corrupt and the drive is probably malfunctioning. In that case, go to Step 11. If you ever have another problem with the drive, replace it immediately.
If you can start and log in in safe mode, empty the Trash, and then open the Finder Info window on the startup volume ("Macintosh HD," unless you gave it a different name.) Check that you have at least 9 GB of available space, as shown in the window. If you don't, copy as many files as necessary to another volume (not another folder on the same volume) and delete the originals. Deletion isn't complete until you empty the Trash again. Do this until the available space is more than 9 GB. Then restart as usual (i.e., not in safe mode.)
If the startup process hangs again, the problem is likely caused by a third-party system modification that you installed. Post for further instructions.
Step 8
Launch Disk Utility in Recovery mode (see Step 1.) Select the startup volume, then run Repair Disk. If any problems are found, repeat until clear. If Disk Utility reports that the volume can't be repaired, the drive has malfunctioned and should be replaced. You might choose to tolerate one such malfunction in the life of the drive. In that case, erase the volume and restore from a backup. If the same thing ever happens again, replace the drive immediately.
This is one of the rare situations in which you should also run Repair Permissions, ignoring the false warnings it may produce. Look for the line "Permissions repair complete" at the end of the output. Then restart as usual.
Step 9
If the startup device is an aftermarket SSD, it may need a firmware update and/or a forced "garbage collection." Instructions for doing this with a Crucial-branded SSD were posted here. Some of those instructions may apply to other brands of SSD, but you should check with the vendor's tech support.
Step 10
Reinstall the OS. If the Mac was upgraded from an older version of OS X, you’ll need the Apple ID and password you used to upgrade.
Step 11
Do as in Step 9, but this time erase the startup volume in Disk Utility before installing. The system should automatically restart into the Setup Assistant. Follow the prompts to transfer the data from a Time Machine or other backup.
Step 12
This step applies only to models that have a logic-board ("PRAM") battery: all Mac Pro's and some others (not current models.) Both desktop and portable Macs used to have such a battery. The logic-board battery, if there is one, is separate from the main battery of a portable. A dead logic-board battery can cause a startup failure. Typically the failure will be preceded by loss of the settings for the startup disk and system clock. See the user manual for replacement instructions. You may have to take the machine to a service provider to have the battery replaced.
Step 13
If you get this far, you're probably dealing with a hardware fault. Make a "Genius" appointment at an Apple Store, or go to another authorized service provider.

HT204053 Our family uses one Apple ID for all of our iPhones. We installed the update and now we are all getting each others photos and texts. How do we stop this?

Our family uses one Apple ID for all of our iPhone 5's. We installed the update and now we are all receiving each other's pictures and texts. How do we stop this?

Have a look here...
http://macmost.com/setting-up-multiple-ios-devices-for-messages-and-facetime.htm l

I downloaded the iPhoto update and now it won't open the library on my external hard drive telling me it is locked (which it isn't) what do i do?

i downloaded the iPhoto update and now it won't open the library on my external hard drive telling me it is locked (which it isn't) what do i do?

What version of iPhoto?
What format is the disk?

I took my phone off the charger and wifi while it was updating and now it wont let me on the phone nor my computer. how do i get it to finish updating or turn on?

i took my phone off the charger and wifi while it was updating and now it wont let me on the phone nor my computer and it just has the apple icon on the screen. how do i get it to finish updating or turn on?

Why would you do that when your phone is updating?
Your phone is in recovery mode If you can't update or restore your iOS device

I did the update and now cant open itunes i get a error 7 windows error 198

I did the update and now itunes wont open...I get a windows error 7 (windows error 198) HELP

Hello there, thumerick.
The following Knowledge Base article addresses the very issue you're describing:
iTunes 11.1.4 for Windows: Unable to install or open
http://support.apple.com/kb/TS5376
Check for .dll files
Go to C:\Program Files (x86)\iTunes and C:\Program Files\iTunes and look for .dll files.
If you find QTMovie.DLL, or any other .dll files, move them to the desktop.
Reboot your computer.
Note: Depending on your operating system, you may only have one of the listed paths.
Uninstall and reinstall iTunes
Uninstall iTunes and all of its related components.
Reboot your computer. If you can't uninstall a piece of Apple software, try using the Microsoft Program Install and Uninstall Utility.
Re-download and reinstall iTunes 11.1.4.
Thanks for reaching out to Apple Support Communities.
Cheers,
Pedro.

I just installed the latest software update and now I can't open Mail 4.5 on my Mini 2,1. How do I re-install Mail?

I just installed the latest software update and now I can't open Mail 4.5. This is a Mini 2,1 using OSX 10.6.8.

Try re-installing the big 10.6.8 Combo...
http://support.apple.com/kb/DL1399
Repair Permissions afterwords, reboot.

Fire fox did an update, and now will not work at all.

Firefox did an update, and now will not open, it tells me that it cannot access any site I try

[[Firewalls]] can block a new version of Firefox. See [[Cannot connect after upgrading Firefox]]

Updated bios via Live Update and now my Network card isn't detected

Similar Messages

Maybe you are looking for