URGENT HELP-Connecting 2 Switches

Hi All,
I need to connect 2 switches (2960 & 2960S) with only one single link in our LAN network. This is to get extra number of ports.
Requesting your help with the followings:
Please confirm if straight throug cable will work to connect between the above two switches
What will be the best configuration on each port (in sw1 & 2) to avoid any kind of loop? For example: spanning tree command
Please advise
Thanks in advance

Ok. Here are the outputs:
For SW1:
sw1#show vtp status
VTP Version capable             : 1 to 3
VTP version running             : 2
VTP Domain Name                 : dr
VTP Pruning Mode                : Disabled
VTP Traps Generation            : Disabled
Device ID                       : 9caf.ca74.8400
Configuration last modified by 10.212.100.11 at 9-2-13 12:20:53
Local updater ID is 10.212.100.11 on interface Vl100 (lowest numbered VLAN interface found)
Feature VLAN:
VTP Operating Mode                : Server
Maximum VLANs supported locally   : 255
Number of existing VLANs          : 15
Configuration Revision            : 17
MD5 digest                        : 0xDE 0xA3 0x3E 0x80 0x2A 0x70 0x29 0xEC
                                    0xBB 0x30 0x88 0x32 0x6D 0x17 0x22 0x9A
sw1#show spanning-tree vlan 100
VLAN0100
  Spanning tree enabled protocol rstp
  Root ID    Priority    32868
             Address     9caf.ca74.8400
             This bridge is the root
             Hello Time   2 sec  Max Age 20 sec  Forward Delay 15 sec
  Bridge ID  Priority    32868  (priority 32768 sys-id-ext 100)
             Address     9caf.ca74.8400
             Hello Time   2 sec  Max Age 20 sec  Forward Delay 15 sec
             Aging Time  300 sec
Interface           Role Sts Cost      Prio.Nbr Type
Gi0/1               Desg FWD 4         128.1    P2p Edge
Gi0/6               Desg FWD 19        128.6    P2p Edge
Gi0/7               Desg FWD 4         128.7    P2p
Gi0/8               Desg FWD 4         128.8    P2p
Gi0/9               Desg FWD 19        128.9    P2p Edge
Gi0/10              Desg FWD 19        128.10   P2p
Gi0/15              Desg FWD 19        128.15   P2p Edge
Gi0/16              Desg FWD 19        128.16   P2p Edge
Interface           Role Sts Cost      Prio.Nbr Type
Gi0/21              Desg FWD 4         128.21   P2p
Gi0/22              Desg FWD 4         128.22   P2p Edge
Po6                 Desg FWD 2         128.96   P2p
sw1#show spanning-tree vlan 103
VLAN0103
  Spanning tree enabled protocol rstp
  Root ID    Priority    32871
             Address     9caf.ca74.8400
             This bridge is the root
             Hello Time   2 sec  Max Age 20 sec  Forward Delay 15 sec
  Bridge ID  Priority    32871  (priority 32768 sys-id-ext 103)
             Address     9caf.ca74.8400
             Hello Time   2 sec  Max Age 20 sec  Forward Delay 15 sec
             Aging Time  300 sec
Interface           Role Sts Cost      Prio.Nbr Type
Gi0/7               Desg FWD 4         128.7    P2p
Gi0/8               Desg FWD 4         128.8    P2p
Gi0/21              Desg FWD 4         128.21   P2p
Po6                 Desg FWD 2         128.96   P2p
For SW2:
sw2#show vtp s
qadr-sw2#show vtp status
VTP Version capable             : 1 to 3
VTP version running             : 2
VTP Domain Name                 : dr
VTP Pruning Mode                : Disabled
VTP Traps Generation            : Disabled
Device ID                       : 9caf.ca7b.3800
Configuration last modified by 10.212.100.11 at 9-2-13 12:20:53
Local updater ID is 10.212.100.12 on interface Vl100 (lowest numbered VLAN interface found)
Feature VLAN:
VTP Operating Mode                : Server
Maximum VLANs supported locally   : 255
Number of existing VLANs          : 15
Configuration Revision            : 17
MD5 digest                        : 0xDE 0xA3 0x3E 0x80 0x2A 0x70 0x29 0xEC
                                    0xBB 0x30 0x88 0x32 0x6D 0x17 0x22 0x9A
sw2#show spanning-tree vlan 100
VLAN0100
  Spanning tree enabled protocol rstp
  Root ID    Priority    32868
             Address     9caf.ca74.8400
             Cost        2
             Port        96 (Port-channel6)
             Hello Time   2 sec  Max Age 20 sec  Forward Delay 15 sec
  Bridge ID  Priority    32868  (priority 32768 sys-id-ext 100)
             Address     9caf.ca7b.3800
             Hello Time   2 sec  Max Age 20 sec  Forward Delay 15 sec
             Aging Time  300 sec
Interface           Role Sts Cost      Prio.Nbr Type
Gi0/1               Desg FWD 4         128.1    P2p Edge
Gi0/6               Desg FWD 19        128.6    P2p Edge
Gi0/7               Desg FWD 4         128.7    P2p
Gi0/8               Desg FWD 4         128.8    P2p
Gi0/9               Desg FWD 19        128.9    P2p Edge
Gi0/14              Desg FWD 4         128.14   P2p Edge
Gi0/15              Desg FWD 19        128.15   P2p Edge
Gi0/21              Desg FWD 4         128.21   P2p Edge
Gi0/22              Desg FWD 4         128.22   P2p
Po6                 Root FWD 2         128.96   P2p
sw2#show spanning-tree vlan 103
VLAN0103
  Spanning tree enabled protocol rstp
  Root ID    Priority    32871
             Address     9caf.ca74.8400
             Cost        2
             Port        96 (Port-channel6)
             Hello Time   2 sec  Max Age 20 sec  Forward Delay 15 sec
  Bridge ID  Priority    32871  (priority 32768 sys-id-ext 103)
             Address     9caf.ca7b.3800
             Hello Time   2 sec  Max Age 20 sec  Forward Delay 15 sec
             Aging Time  300 sec
Interface           Role Sts Cost      Prio.Nbr Type
Gi0/7               Desg FWD 4         128.7    P2p
Gi0/8               Desg FWD 4         128.8    P2p
Gi0/22              Desg FWD 4         128.22   P2p
Po6                 Root FWD 2         128.96   P2p

Similar Messages

  • URGENT HELP-CONFIGURE SWITCH 3560

    Dear All,
    I have here in my company 25 Cisco Switch 3560 .
    as i know, i will configure the Switch with the Basic configuration like Hostname & IP-Address - & Gateway.
    My 2 question is :-
    1- if i configure the switch with the Basic Configuration like IP-Address & Subnet mask & So on , where its saved on the Switch Exactly ?
    2- instead of have the 25 Switch in-front of me , and assign each switch his configuration like IP-Address & all the Things, is there any way to copy the Configurations from the switch which i configured on the Text file & then on each switch i will modify the Text file which include the configuration for that switch ( New configuration ) & then apply to that switch ( the New one ) ?
    if i can do like that , can i & HOW CAN I DO IT , PLEASE HELP ME BY WRITING THE COMMAND WHICH I NEED TO FOLLOW IT ?
    Thanks .
    Rania.

    Hi Rania,
    When you just configure the switch all the config is in DRAM (running config) but when you do wr me it is saved in NVRAM (startup config).
    What you can do is write all the commands for ip address and the configs what you want on wordpad and from there you can modify the lines what you want for each switch and just copy it and paste on the switch global config mode.
    Remember you have to create all the vlans manually in vlan database or you can configure one switch as VTp server and another switch as VTP client and all the vlans will be synched to the switches which are in VTP client mode.
    To configure ip address
    int vlan 1
    ip address x.x.x.x x.x.x.x
    no shut
    to configure hostname
    config t
    hostname
    This link is a complete config guide which will guide you with all what you want to configure on 3560 switch
    http://www.cisco.com/univercd/cc/td/doc/product/lan/cat3560/12119ea1/3560scg/index.htm
    HTH
    Ankur

  • Urgent Help Required for Connect Four Game

    Hi all,
    I am a student and I have a project due 20th of this month, I mean May 20, 2007 after 8 days. The project is about creating a Connect Four Game. I have found some code examples on the internet which helped me little bit. But there are lot of problems I am facing developing the whole game. I have drawn the Board and the two players can play. The players numbers can fill the board, but I have problem implementing the winner for the game. I need to implement the hasWon() method for Horizontal win, Vertical win and Diagonal win. I also found some code examples on the net but I was unable to make it working. I have 5 classes and one interface which I m implementing. The main problem is how to implement the hasWon() method in the PlayGame class below with Horizontal, vertical and diagonal moves.
    Sorry there is so much code.
    This the interface I must implement, but now I am only implementing the int move() of this interface. I will implement the rest later after solving the winner problem with your help.
    Interface code..............
    interface Player {
    void init (Boolean color);
    String name ();
    int move ();
    void inform (int i);
    Player1 class......................
    import java.util.*;
    import java.io.*;
    import javax.swing.*;
    public class Player1 implements Player
    public Player1()
    public int move()
    Scanner scan = new Scanner(System.in);
    // BufferedReader stdin = new BufferedReader (new InputStreamReader(System.in));
    int player1;
    System.out.println ("What is your Number, player 1?");
    player1 = scan.nextInt();
    System.out.println ("Hey number"+player1+" are you prepared to CONNECT FOUR");
    System.out.println();
    return player1;
    //Player.move();
    //return player1;
    }//end move method
    public void init (Boolean color)
    public void inform (int i)
    public String name()
    return "Koonda";
    }//end player1 class
    Player2 class...........................
    import java.util.*;
    import java.io.*;
    import javax.swing.*;
    public class Player2 implements Player
    public int move()
    //int cup0,cup1,cup2,cup3,cup4,cup5,cup6;
    // cup0=5;cup1=5;cup2=5;cup3=5;cup4=5;cup5=5;cup6=5;
    //int num1, num2;
    Scanner scan = new Scanner(System.in);
    // BufferedReader stdin = new BufferedReader (new InputStreamReader(System.in));
    int player2;
    System.out.println ("What is your Number, player 2?");
    player2 = scan.nextInt();
    System.out.println ("Hey "+player2+" are you prepared to CONNECT FOUR");
    System.out.println();
    //return player1;
    return player2;
    }//end move method
    public void init (Boolean color)
    public void inform (int i)
    public String name()
    return "malook";
    }//end player1 class
    PlayGame class which contains all the functionality.........................................................
    import java.util.*;
    import java.io.*;
    import javax.swing.*;
    public class PlayGame
    //Player player1;
    //Player player2;
    int [][]ConnectFourArray;
    boolean status;
    int winner;
         int player1;
         int player2;
         public PlayGame()
              //this.player1 = player1;
              //this.player2 = player2;
         public void StartGame()
         try{
         // int X = 0, Y = 0;
         //int value;
         int cup0,cup1,cup2,cup3,cup4,cup5,cup6;
    cup0=5;cup1=5;cup2=5;cup3=5;cup4=5;cup5=5;cup6=5;
         int[][] ConnectFourArray = new int[6][7];
         int num1, num2;
         for(int limit=21;limit!=0;limit--)
    BufferedReader selecter = new BufferedReader (new InputStreamReader(System.in));
    String column1;
    System.out.println();
    for ( int row=0; row < ConnectFourArray.length; row++ ){
    System.out.print("Row " + row + ": ");
    for ( int col=0; col < ConnectFourArray[row].length; col++ )
    System.out.print( ConnectFourArray[row][col] + " ");
    System.out.println();
    System.out.println();
    System.out.println ("Please Select a column of 0 through 6 ");
    column1 = selecter.readLine();
    num1= Integer.parseInt(column1);
    System.out.println();
    if (num1==0){
    ConnectFourArray[cup0][0]=1;
    cup0=cup0-1;
    else if (num1==1){
    ConnectFourArray[cup1][1]=1;
    cup1=cup1-1;
    else if (num1==2){
    ConnectFourArray[cup2][2]=1;
    cup2=cup2-1;
    else if (num1==3){
    ConnectFourArray[cup3][3]=1;
    cup3=cup3-1;
    else if (num1==4){
    ConnectFourArray[cup4][4]=1;
    cup4=cup4-1;
    else if (num1==5){
    ConnectFourArray[cup5][5]=1;
    cup5=cup5-1;
    else if (num1==6){
    ConnectFourArray[cup6][6]=1;
    cup6=cup6-1;
    System.out.println();
    BufferedReader selecter2 = new BufferedReader (new InputStreamReader(System.in));
    String column2;
    System.out.println();
    for ( int row=0; row < ConnectFourArray.length; row++ ){
    System.out.print("Row " + row + ": ");
    for ( int col=0; col < ConnectFourArray[row].length; col++ )
    System.out.print( ConnectFourArray[row][col] + " ");
    System.out.println();
    System.out.println();
    System.out.println ("Please Select a column of 0 through 6 ");
    column1 = selecter.readLine();
    num1= Integer.parseInt(column1);
    System.out.println();
    if (num1==0){
    ConnectFourArray[cup0][0]=2;
    cup0=cup0-1;
    else if (num1==1){
    ConnectFourArray[cup1][1]=2;
    cup1=cup1-1;
    else if (num1==2){
    ConnectFourArray[cup2][2]=2;
    cup2=cup2-1;
    else if (num1==3){
    ConnectFourArray[cup3][3]=2;
    cup3=cup3-1;
    else if (num1==4){
    ConnectFourArray[cup4][4]=2;
    cup4=cup4-1;
    else if (num1==5){
    ConnectFourArray[cup5][5]=2;
    cup5=cup5-1;
    else if (num1==6){
    ConnectFourArray[cup6][6]=2;
    cup6=cup6-1;
    System.out.println();
    System.out.println();
    catch (Exception E){
    System.out.println("Error with input");
    System.out.println("Would you like to play again");
    try{
    String value;
    BufferedReader reader = new BufferedReader (new InputStreamReader(System.in));
    // Scanner scan = new Scanner(System.in);
    System.out.println("Enter yes to play or no to quit");
    // value = scan.nextLine();
    // String value2;
    value = reader.readLine();
    //value2 = reader.readLine();
    if (value.equals("yes"))
    System.out.println("Start again");
    StartGame(); // calling the StartGame method to play a game once more
    else if (value.equals("no"))
    System.out.println("No more games to play");
    // System.exit(0);
    else
    System.exit(0);
    System.out.println();
    catch (Exception e){
    System.out.println("Error with input");
    finally
    System.out.println(" playing done");
    //StartGame();
    //check for horizontal win
    public int hasWon()
    int status = 0;
    for (int row=0; row<6; row++)
    for (int col=0; col<4; col++)
    if (ConnectFourArray[col][row] != 0 &&
    ConnectFourArray[col][row] == ConnectFourArray[col+1][row] &&
    ConnectFourArray[col][row] == ConnectFourArray[col+2][row] &&
    ConnectFourArray[col][row] == ConnectFourArray[col+3][row])
    //status = true;//int winner;
    if(status == player1)
    System.out.println("Player 1 is the winner");
    else if(status == player2)
    System.out.println("Player 2 is the winner" );
    }//end inner for loop
    }// end outer for loop
    } // end method Winner
    return status;
    }//end class
    ClassConnectFour which designs the board........................
    import java.util.*;
    import java.io.*;
    import javax.swing.*;
    public class ClassConnectFour
         //Player player1;
         //Player player2;
         public ClassConnectFour()
              //this.player1 = player1;
    public void DrawBoard()
    int[][] ConnectFourArray = new int[6][7] ;
    for ( int row=0; row < ConnectFourArray.length; row++ ){
    System.out.print("Row " + row + ": ");
    for ( int col=0; col < ConnectFourArray[row].length; col++ )
    System.out.print( ConnectFourArray[row][col] + " ");
    System.out.println();
    System.out.println();
    }//end class
    TestConnetFour class which uses most of the above class..................
    import java.util.*;
    import java.io.*;
    import javax.swing.*;
    public class TestConnectFour
    public static void main(String[] args)
    ClassConnectFour cf = new ClassConnectFour();
    cf.DrawBoard();
    Player1 player1 = new Player1();
    Player2 player2 = new Player2();
    player1.move();
    player2.move();
    System.out.println("Number 1 belongs to player " + player1.name());
    System.out.println("Number 2 belongs to player " + player2.name());
    PlayGame pg = new PlayGame();
    pg.StartGame();
    pg.hasWon();
    //pg.Play();
    //System.out.println(player.name());
    //System.out.println(player2.name());
    }// end main
    }//end class
    I am sorry for all this junk code but I only understand it this way. Your urgent help is required. Looking forward to your reply.
    Thanks in advance.
    Koonda
    //

    Hi,
    Thanks for your help but I really don't understand the table lookup algorithm. Could you please send me some code to implement that.
    I will send you the formatted code as well
    Thanks for your help.
    looking forward to your reply.
    Koonda
    Hi all,
    I am a student and I have a project due 20th of this month, I mean May 20, 2007 after 8 days. The project is about creating a Connect Four Game. I have found some code examples on the internet which helped me little bit. But there are lot of problems I am facing developing the whole game. I have drawn the Board and the two players can play. The players numbers can fill the board, but I have problem implementing the winner for the game. I need to implement the hasWon() method for Horizontal win, Vertical win and Diagonal win. I also found some code examples on the net but I was unable to make it working. I have 5 classes and one interface which I m implementing. The main problem is how to implement the hasWon() method in the PlayGame class below with Horizontal, vertical and diagonal moves.
    Sorry there is so much code.
    This the interface I must implement, but now I am only implementing the int move() of this interface. I will implement the rest later after solving the winner problem with your help.
    Interface code..............
    interface Player {
    void init (Boolean color);
    String name ();
    int move ();
    void inform (int i);
    Player1 class......................
    import java.util.*;
    import java.io.*;
    import javax.swing.*;
    public class Player1 implements Player
    public Player1()
    public int move()
    Scanner scan = new Scanner(System.in);
    // BufferedReader stdin = new BufferedReader (new InputStreamReader(System.in));
    int player1;
    System.out.println ("What is your Number, player 1?");
    player1 = scan.nextInt();
    System.out.println ("Hey number"+player1+" are you prepared to CONNECT FOUR");
    System.out.println();
    return player1;
    //Player.move();
    //return player1;
    }//end move method
    public void init (Boolean color)
    public void inform (int i)
    public String name()
    return "Koonda";
    }//end player1 class
    Player2 class...........................
    import java.util.*;
    import java.io.*;
    import javax.swing.*;
    public class Player2 implements Player
    public int move()
    //int cup0,cup1,cup2,cup3,cup4,cup5,cup6;
    // cup0=5;cup1=5;cup2=5;cup3=5;cup4=5;cup5=5;cup6=5;
    //int num1, num2;
    Scanner scan = new Scanner(System.in);
    // BufferedReader stdin = new BufferedReader (new InputStreamReader(System.in));
    int player2;
    System.out.println ("What is your Number, player 2?");
    player2 = scan.nextInt();
    System.out.println ("Hey "+player2+" are you prepared to CONNECT FOUR");
    System.out.println();
    //return player1;
    return player2;
    }//end move method
    public void init (Boolean color)
    public void inform (int i)
    public String name()
    return "malook";
    }//end player1 class
    PlayGame class which contains all the functionality.........................................................
    import java.util.*;
    import java.io.*;
    import javax.swing.*;
    public class PlayGame
    //Player player1;
    //Player player2;
    int [][]ConnectFourArray;
    boolean status;
    int winner;
    int player1;
    int player2;
    public PlayGame()
    //this.player1 = player1;
    //this.player2 = player2;
    public void StartGame()
    try{
    // int X = 0, Y = 0;
    //int value;
    int cup0,cup1,cup2,cup3,cup4,cup5,cup6;
    cup0=5;cup1=5;cup2=5;cup3=5;cup4=5;cup5=5;cup6=5;
    int[][] ConnectFourArray = new int[6][7];
    int num1, num2;
    for(int limit=21;limit!=0;limit--)
    BufferedReader selecter = new BufferedReader (new InputStreamReader(System.in));
    String column1;
    System.out.println();
    for ( int row=0; row < ConnectFourArray.length; row++ ){
    System.out.print("Row " + row + ": ");
    for ( int col=0; col < ConnectFourArray[row].length; col++ )
    System.out.print( ConnectFourArray[row][col] + " ");
    System.out.println();
    System.out.println();
    System.out.println ("Please Select a column of 0 through 6 ");
    column1 = selecter.readLine();
    num1= Integer.parseInt(column1);
    System.out.println();
    if (num1==0){
    ConnectFourArray[cup0][0]=1;
    cup0=cup0-1;
    else if (num1==1){
    ConnectFourArray[cup1][1]=1;
    cup1=cup1-1;
    else if (num1==2){
    ConnectFourArray[cup2][2]=1;
    cup2=cup2-1;
    else if (num1==3){
    ConnectFourArray[cup3][3]=1;
    cup3=cup3-1;
    else if (num1==4){
    ConnectFourArray[cup4][4]=1;
    cup4=cup4-1;
    else if (num1==5){
    ConnectFourArray[cup5][5]=1;
    cup5=cup5-1;
    else if (num1==6){
    ConnectFourArray[cup6][6]=1;
    cup6=cup6-1;
    System.out.println();
    BufferedReader selecter2 = new BufferedReader (new InputStreamReader(System.in));
    String column2;
    System.out.println();
    for ( int row=0; row < ConnectFourArray.length; row++ ){
    System.out.print("Row " + row + ": ");
    for ( int col=0; col < ConnectFourArray[row].length; col++ )
    System.out.print( ConnectFourArray[row][col] + " ");
    System.out.println();
    System.out.println();
    System.out.println ("Please Select a column of 0 through 6 ");
    column1 = selecter.readLine();
    num1= Integer.parseInt(column1);
    System.out.println();
    if (num1==0){
    ConnectFourArray[cup0][0]=2;
    cup0=cup0-1;
    else if (num1==1){
    ConnectFourArray[cup1][1]=2;
    cup1=cup1-1;
    else if (num1==2){
    ConnectFourArray[cup2][2]=2;
    cup2=cup2-1;
    else if (num1==3){
    ConnectFourArray[cup3][3]=2;
    cup3=cup3-1;
    else if (num1==4){
    ConnectFourArray[cup4][4]=2;
    cup4=cup4-1;
    else if (num1==5){
    ConnectFourArray[cup5][5]=2;
    cup5=cup5-1;
    else if (num1==6){
    ConnectFourArray[cup6][6]=2;
    cup6=cup6-1;
    System.out.println();
    System.out.println();
    catch (Exception E){
    System.out.println("Error with input");
    System.out.println("Would you like to play again");
    try{
    String value;
    BufferedReader reader = new BufferedReader (new InputStreamReader(System.in));
    // Scanner scan = new Scanner(System.in);
    System.out.println("Enter yes to play or no to quit");
    // value = scan.nextLine();
    // String value2;
    value = reader.readLine();
    //value2 = reader.readLine();
    if (value.equals("yes"))
    System.out.println("Start again");
    StartGame(); // calling the StartGame method to play a game once more
    else if (value.equals("no"))
    System.out.println("No more games to play");
    // System.exit(0);
    else
    System.exit(0);
    System.out.println();
    catch (Exception e){
    System.out.println("Error with input");
    finally
    System.out.println(" playing done");
    //StartGame();
    //check for horizontal win
    public int hasWon()
    int status = 0;
    for (int row=0; row<6; row++)
    for (int col=0; col<4; col++)
    if (ConnectFourArray[col][row] != 0 &&
    ConnectFourArray[col][row] == ConnectFourArray[col+1][row] &&
    ConnectFourArray[col][row] == ConnectFourArray[col+2][row] &&
    ConnectFourArray[col][row] == ConnectFourArray[col+3][row])
    //status = true;//int winner;
    if(status == player1)
    System.out.println("Player 1 is the winner");
    else if(status == player2)
    System.out.println("Player 2 is the winner" );
    }//end inner for loop
    }// end outer for loop
    } // end method Winner
    return status;
    }//end class
    ClassConnectFour which designs the board........................
    import java.util.*;
    import java.io.*;
    import javax.swing.*;
    public class ClassConnectFour
    //Player player1;
    //Player player2;
    public ClassConnectFour()
    //this.player1 = player1;
    public void DrawBoard()
    int[][] ConnectFourArray = new int[6][7] ;
    for ( int row=0; row < ConnectFourArray.length; row++ ){
    System.out.print("Row " + row + ": ");
    for ( int col=0; col < ConnectFourArray[row].length; col++ )
    System.out.print( ConnectFourArray[row][col] + " ");
    System.out.println();
    System.out.println();
    }//end class
    TestConnetFour class which uses most of the above class..................
    import java.util.*;
    import java.io.*;
    import javax.swing.*;
    public class TestConnectFour
    public static void main(String[] args)
    ClassConnectFour cf = new ClassConnectFour();
    cf.DrawBoard();
    Player1 player1 = new Player1();
    Player2 player2 = new Player2();
    player1.move();
    player2.move();
    System.out.println("Number 1 belongs to player " + player1.name());
    System.out.println("Number 2 belongs to player " + player2.name());
    PlayGame pg = new PlayGame();
    pg.StartGame();
    pg.hasWon();
    //pg.Play();
    //System.out.println(player.name());
    //System.out.println(player2.name());
    }// end main
    }//end classI am sorry for all this junk code but I only understand it this way. Your urgent help is required. Looking forward to your reply.
    Thanks in advance.
    Koonda

  • No more connections available to this remote computer...Urgent Help for File server...

    Hi Guys,
    I need urgent help regards to our school File server which is having "No more connection to this remote computer error"
    on SMB Shares where I usually authenticate with a domain username it used to work fine since till 3 weeks ago.
    Now I can browse the SMB shares with only IP... Netbios gets straight away this error message from non-domain joined pc's where the computer needs to connect to the SCCM distribution point on this file server.
    Strangely, Domain joined pc's does not have this problem at all they can use Netbios or IP no problem at all. But someone from a standalone laptop or desktop who needs to access shares through netbios gets this message.
    Can someone help me please?
    I did check DNS yet there is no problem on DNS I checked PTR record for the server to make sure it is not turned in to multihome accidently but nothing at all.
    I also did a NETMON where I captured the data from server and the client I get these errors:
    205 4:54:35 PM 16/12/2013
    7.3299179 10.2.1.96
    10.2.0.13 TCP
    TCP:Flags=......S., SrcPort=49312, DstPort=Microsoft-DS(445), PayloadLen=0, Seq=1771710719, Ack=0, Win=8192 ( Negotiating scale factor 0x2 ) = 8192
    {TCP:22, IPv4:21}
    206 4:54:35 PM 16/12/2013
    7.3299668 10.2.0.13
    10.2.1.96 TCP
    TCP:Flags=...A..S., SrcPort=Microsoft-DS(445), DstPort=49312, PayloadLen=0, Seq=2167618331, Ack=1771710720, Win=8192 ( Negotiated scale factor 0x8 ) = 2097152
    {TCP:22, IPv4:21}
    207 4:54:35 PM 16/12/2013
    7.3301468 10.2.1.96
    10.2.0.13 TCP
    TCP:Flags=...A...., SrcPort=49312, DstPort=Microsoft-DS(445), PayloadLen=0, Seq=1771710720, Ack=2167618332, Win=16425 (scale factor 0x2) = 65700
    {TCP:22, IPv4:21}
    208 4:54:35 PM 16/12/2013
    7.3301468 10.2.1.96
    10.2.0.13 SMB
    SMB:C; Negotiate, Dialect = PC NETWORK PROGRAM 1.0, LANMAN1.0, Windows for Workgroups 3.1a, LM1.2X002, LANMAN2.1, NT LM 0.12, SMB 2.002, SMB 2.???
    {SMBOverTCP:23, TCP:22, IPv4:21}
    209 4:54:35 PM 16/12/2013
    7.3307974 10.2.0.13
    10.2.1.96 SMB2
    SMB2:R   NEGOTIATE (0x0), GUID={8447F237-5219-D48A-40C0-29092450C68E}
    {SMBOverTCP:23, TCP:22, IPv4:21}
    210 4:54:35 PM 16/12/2013
    7.3314064 10.2.1.96
    10.2.0.13 SMB2
    SMB2:C   SESSION SETUP (0x1) {SMBOverTCP:23, TCP:22, IPv4:21}
    211 4:54:35 PM 16/12/2013
    7.3318815 10.2.0.13
    10.2.1.96 SMB2
    SMB2:R  - NT Status: System - Error, Code = (22) STATUS_MORE_PROCESSING_REQUIRED  SESSION SETUP (0x1), SessionFlags=0x0
    {SMBOverTCP:23, TCP:22, IPv4:21}
    212 4:54:35 PM 16/12/2013
    7.3324012 10.2.1.96
    10.2.0.13 SMB2
    SMB2:C   SESSION SETUP (0x1) {SMBOverTCP:23, TCP:22, IPv4:21}
    215 4:54:35 PM 16/12/2013
    7.3339977 10.2.0.13
    10.2.1.96 SMB2
    SMB2:R  - NT Status: System - Error, Code = (109) STATUS_LOGON_FAILURE  SESSION SETUP (0x1)  
    {SMBOverTCP:23, TCP:22, IPv4:21}
    216 4:54:35 PM 16/12/2013
    7.3341805 10.2.1.96
    10.2.0.13 TCP
    TCP:Flags=...A.R.., SrcPort=49312, DstPort=Microsoft-DS(445), PayloadLen=0, Seq=1771711788, Ack=2167619070, Win=0 (scale factor 0x2) = 0
    {TCP:22, IPv4:21}
    217 4:54:35 PM 16/12/2013
    7.3357089 10.2.1.96
    10.2.0.13 TCP
    TCP:Flags=......S., SrcPort=49313, DstPort=Microsoft-DS(445), PayloadLen=0, Seq=2943201172, Ack=0, Win=8192 ( Negotiating scale factor 0x2 ) = 8192
    {TCP:27, IPv4:21}
    218 4:54:35 PM 16/12/2013
    7.3357422 10.2.0.13
    10.2.1.96 TCP
    TCP:Flags=...A..S., SrcPort=Microsoft-DS(445), DstPort=49313, PayloadLen=0, Seq=3718656547, Ack=2943201173, Win=8192 ( Negotiated scale factor 0x8 ) = 2097152
    {TCP:27, IPv4:21}
    219 4:54:35 PM 16/12/2013
    7.3359768 10.2.1.96
    10.2.0.13 TCP
    TCP:Flags=...A...., SrcPort=49313, DstPort=Microsoft-DS(445), PayloadLen=0, Seq=2943201173, Ack=3718656548, Win=16425 (scale factor 0x2) = 65700
    {TCP:27, IPv4:21}
    220 4:54:35 PM 16/12/2013
    7.3359768 10.2.1.96
    10.2.0.13 SMB2
    SMB2:C   NEGOTIATE (0x0), GUID={8213462D-2600-D1B1-11E3-65FC4BCDE707}
    {SMBOverTCP:28, TCP:27, IPv4:21}
    221 4:54:35 PM 16/12/2013
    7.3364173 10.2.0.13
    10.2.1.96 SMB2
    SMB2:R   NEGOTIATE (0x0), GUID={8447F237-5219-D48A-40C0-29092450C68E}
    {SMBOverTCP:28, TCP:27, IPv4:21}
    222 4:54:35 PM 16/12/2013
    7.3369702 10.2.1.96
    10.2.0.13 SMB2
    SMB2:C   SESSION SETUP (0x1) {SMBOverTCP:28, TCP:27, IPv4:21}
    223 4:54:35 PM 16/12/2013
    7.3373474 10.2.0.13
    10.2.1.96 SMB2
    SMB2:R  - NT Status: System - Error, Code = (22) STATUS_MORE_PROCESSING_REQUIRED  SESSION SETUP (0x1), SessionFlags=0x0
    {SMBOverTCP:28, TCP:27, IPv4:21}
    224 4:54:35 PM 16/12/2013
    7.3377060 10.2.1.96
    10.2.0.13 SMB2
    SMB2:C   SESSION SETUP (0x1) {SMBOverTCP:28, TCP:27, IPv4:21}
    227 4:54:35 PM 16/12/2013
    7.3390552 10.2.0.13
    10.2.1.96 SMB2
    SMB2:R  - NT Status: System - Error, Code = (109) STATUS_LOGON_FAILURE  SESSION SETUP (0x1)  
    {SMBOverTCP:28, TCP:27, IPv4:21}
    Regards,
    Gokhan

    Solution has been found, 
    After doing bit of a backtrack, site DC's were out of sync with PDC with time.
    Also Time service was shutdown on PDC which has been enabled and pointed to the Australian pool ntp IP address.
    Everything is back on track now.
    Regards,
    Gokhan Cil

  • Computer restarts when ipod is connected urgent help needed

    alright this is weird, I've had my ipod for ages and suddenly I go to plug it in and the computer slows down really really really slow and eventually just turns it self off, restarts and then sits in a black screen. if I leave the ipod plugged into the computer and restart it again it just goes straight back to the black screen, but both my ipod and computer work fine when there not connected. i have the latest version of itunes which seemed to help the first time i tried it actually started to update the ipod but then guess what the computer has another heart attack. urgent help needed please!!!

    if I leave the ipod plugged into the computer and restart it again it just goes straight back to the black screen
    Given this, I'd put it down to a flaky power supply in the computer. Might want to try using another computer or replacing the PSU.

  • Switch until release using keyboard...need urgent help

    Hi,
    i have a problem of configuring "switch until release" action using keyboard....
    or is it there no this function at all...
    it seems like all i can do is press to ON and press again to OFF
    anyone can help...
    need Urgent help....
    thank you in advance..

    This isn't possible because of the way operating systems
    handle keyboard events. When you press a keyboard key, it does not register as
    one key down. For whatever your operating system is set for as far as repeating
    characters, it will register that many key down presses. The mouse works
    differently, when you press the mouse it keeps that event "locked"
    until you release the mouse. Because of this, you can not make a switch until
    release using the keyboard; this definition is only for mouse clicks.
    Brandon Vasquez | Software Engineer | Integration Services | National Instruments

  • Urgent help : Nomadic computing / connected env(long)

    Hi,
    I need some urgent help on the following problem.
    Platform : NT 3.51 as the Env Mgr, server and clients.
    Forte : 2.0.E.1
    The test case is simple :
    Multiple, lets say 3, Forte environments (each a NT machine, but that
    shouldn't be significant), of which one is the "home" environment, Env0,
    as well as the other remote environments, Env1 and Env2. I need to
    connect to Env1, Env2 from Env0 on a completely dynamic basis, i.e. I
    have a list of NS addresses (IP & port) and the particular one is
    selected by the user. "Connect" means anything from the very basic
    invoke a method on a service, to the more sophisticated inspect (&
    change) instruments and invoke commands on all system agents and custom
    agents.
    I started off with the new nomadic stuff : As per Forum and technote
    (#?) x 3. I installed my server partition on Env1 and Env2 and started
    the client with the -fnoins flag. Then I dynamically set the environment
    variable (in NT its in HKEY_CURRENT_USER in the NT registry)
    FORTE_NS_ADDRESS to the new environment, Env1. When I invoked the method
    it fired off the part in the right Env. Then I changed the
    FORTE_NS_ADDRESS, to Env2, and did the task.part.DistObjLOcationMgr.Rele
    aseConnection(EnvMgr).. thing. This was fine. The question now was : How
    do I "connect" to the newly set Env ? I tried everything from simply
    calling my server partition, to server...task.part.GetEnvMgr, to
    registering anchored objects on the blessed ObjLocationMgr ! It just
    didnt connect to the new Env : It stayed connected to Env1 !
    Then I got onto connected environments. Here I also tried a couple of
    things: Most significantly, connecting to Env1 and setting the
    environment search path also did the trick, but again disconnecting from
    Env1 seem troublesome : Q : How do I seperate the original Env0 and Env1
    ? Forte seem to think that its all one big environment now and gave
    strange errors when I disconnected from Env1, connected to Env2 and
    tried to set the environment search path to Env2. Another Q, is there a
    way to dynamically set the environment search path for a SO ? All I
    could do was set the NS environment search path.
    Anyway, my apologies for this long dragged out e-mail, but any ideas
    will help...I'm getting desperate !
    Anton van Niekerk

    Well I hate to say it but I think you borked it somehow. I have no idea what you mean by that green chip connected with two wires and that blue long chip but the fact that you are referring to internal parts that way tells me you didn't really know what you were doing in there. There is a Manual and it can be followed step by step rather than just rushing in and turning screws. I suggest putting it all in a basket and taking it to a repair shop where they can figure it out if possible. Trust me, you will not be the first such case they have ever seen.

  • URGENT HELP NEEDED - iPhone 3Gs no longer detected or charged by MacBook

    My iPhone 3Gs (3.1) has been running fine, until several hours ago today, when I plugged it to my MacBook, the iPhone is no longer detected - it doesn't show up in iTunes, nor it is charged. I tried opening iPhoto, and it wasn't there too. Not with Image Capture too. I tried charging it using the out-of-box wall charger using the same out-of-box USB cable I use for MacBook, and it can be charged without any problem. Then I put it into Recovery mode, and there iTunes can see it. I don't want to restore it before I figure out exactly what went wrong, as I don't want the restore process somehow gets stuck in the middle that the connection is lost again.
    I've tried reinstalled iTunes, including completely removal of Apple Mobile Device Support, as instructed by Apple. But still no luck.
    I've tried switching to another USB port of my MacBook. No luck.
    My iTunes is the latest 9.0.1, and my Mac OSX is 10.6.1. My iPhone is on 3.1, upgraded from 3.0.
    I've read from web that it seems I'm not the only one out there having this problem. But none of them seem having any real working solution.
    Urgent help needed & appreciated. Millions of thanks in advance.
    Gary

    1. I used both cables - theirs & mine ... and on several macs
    2. yes, same cable for wall & mac
    3. as said, i did completely remove & install itunes (incl. apple mobile device support), as instructed on the apple webpage
    anyway, did a restore just now. it seems okay now. but the problem is i have no idea what cause this, and i can't replicate the problem. so i don't know when it will happen again ... maybe a bug with os 3.1 ... others on web said os 3.1 is quite buggy ...

  • Urgent help need on swing problem

    Dear friends,
    I met a problem and need urgent help from guru here, I am Swing newbie,
    I have following code and hope to draw lines between any two components at RUN-TIME, not at design time
    Please throw some skeleton code, Thanks so much!!
    code:
    package com.swing.test;
    import java.awt.*;
    import java.awt.event.*;
    import java.awt.geom.*;
    import javax.swing.*;
    import javax.swing.event.*;
    public class LongguConnectLineCommponent
        public static void main(String[] args)
            JFrame f = new JFrame("Connecting Lines");
            f.setDefaultCloseOperation(JFrame.EXIT_ON_CLOSE);
            f.getContentPane().add(new ConnectionPanel());
            f.setSize(400,300);
            f.setLocation(200,200);
            f.setVisible(true);
    class ConnectionPanel extends JPanel
        JLabel label1, label2, label3, label4;
        JLabel[] labels;
        JLabel selectedLabel;
        int cx, cy;
        public ConnectionPanel()
            setLayout(null);
            addLabels();
            label1.setBounds( 25,  50, 125, 25);
            label2.setBounds(225,  50, 125, 25);
            label3.setBounds( 25, 175, 125, 25);
            label4.setBounds(225, 175, 125, 25);
            determineCenterOfComponents();
            ComponentMover mover = new ComponentMover();
            addMouseListener(mover);
            addMouseMotionListener(mover);
        public void paintComponent(Graphics g)
            super.paintComponent(g);
            Graphics2D g2 = (Graphics2D)g;
            g2.setRenderingHint(RenderingHints.KEY_ANTIALIASING,
                                RenderingHints.VALUE_ANTIALIAS_ON);
            Point[] p;
            for(int i = 0; i < labels.length; i++)
                for(int j = i + 1; j < labels.length; j++)
                    p = getEndPoints(labels, labels[j]);
    //g2.draw(new Line2D.Double(p[0], p[1]));
    private Point[] getEndPoints(Component c1, Component c2)
    Point
    p1 = new Point(),
    p2 = new Point();
    Rectangle
    r1 = c1.getBounds(),
    r2 = c2.getBounds();
    int direction = r1.outcode(r2.x, r2.y);
    switch(direction) // r2 located < direction > of r1
    case (Rectangle.OUT_LEFT): // West
    p1.x = r1.x;
    p1.y = r1.y;
    p2.x = r2.x + r2.width;
    p2.y = r2.y;
    if(r1.y > cy)
    p1.y = r1.y + r1.height;
    p2.y = r2.y + r2.height;
    break;
    case (Rectangle.OUT_TOP): // North
    p1.x = r1.x;
    p1.y = r1.y;
    p2.x = r2.x;
    p2.y = r2.y + r2.height;
    if(r1.x > cx && r2.x > cx)
    p1.x = r1.x + r1.width;
    p2.x = r2.x + r2.width;
    break;
    case (Rectangle.OUT_LEFT + Rectangle.OUT_TOP): // NW
    p1.x = r1.x;
    p1.y = r1.y;
    p2.x = r2.x + r2.width;
    p2.y = r2.y;
    if(r1.y > r2.y + r2.height)
    p2.y = r2.y + r2.height;
    break;
    case (Rectangle.OUT_RIGHT): // East
    p1.x = r1.x + r1.width;
    p1.y = r1.y;
    p2.x = r2.x;
    p2.y = r2.y;
    if(r1.y > cy)
    p1.y = r1.y + r1.height;
    p2.y = r2.y + r2.height;
    break;
    case (Rectangle.OUT_TOP + Rectangle.OUT_RIGHT): // NE
    p1.x = r1.x + r1.width;
    p1.y = r1.y;
    p2.x = r2.x;
    p2.y = r2.y;
    if(r1.y > cy)
    p1.y = r1.y + r1.height;
    p2.y = r2.y + r2.height;
    if(r1.y > r2.y + r2.height)
    p1.y = r1.y;
    else
    if(r1.y > r2.y + r2.height)
    p2.y = r2.y + r2.height;
    break;
    case (Rectangle.OUT_BOTTOM): // South
    p1.x = r1.x;
    p1.y = r1.y + r1.height;
    p2.x = r2.x;
    p2.y = r2.y;
    if(r1.x > cx && r2.x > cx)
    p1.x = r1.x + r1.width;
    p2.x = r2.x + r2.width;
    break;
    case (Rectangle.OUT_RIGHT + Rectangle.OUT_BOTTOM): // SE
    p1.x = r1.x + r1.width;
    p1.y = r1.y + r1.height;
    p2.x = r2.x;
    p2.y = r2.y;
    break;
    case (Rectangle.OUT_BOTTOM + Rectangle.OUT_LEFT): // SW
    p1.x = r1.x;
    p1.y = r1.y + r1.height;
    p2.x = r2.x;
    p2.y = r2.y;
    if(r1.x > r2.x + r2.width)
    p2.x = r2.x + r2.width;
    if(r1.x > cx && r2.x > cx)
    p1.x = r1.x + r1.width;
    p2.x = r2.x + r2.width;
    return new Point[] {p1, p2};
    private void determineCenterOfComponents()
    int
    xMin = Integer.MAX_VALUE,
    yMin = Integer.MAX_VALUE,
    xMax = 0,
    yMax = 0;
    for(int i = 0; i < labels.length; i++)
    Rectangle r = labels[i].getBounds();
    if(r.x < xMin)
    xMin = r.x;
    if(r.y < yMin)
    yMin = r.y;
    if(r.x + r.width > xMax)
    xMax = r.x + r.width;
    if(r.y + r.height > yMax)
    yMax = r.y + r.height;
    cx = xMin + (xMax - xMin)/2;
    cy = yMin + (yMax - yMin)/2;
    private class ComponentMover extends MouseInputAdapter
    Point offsetP = new Point();
    boolean dragging;
    public void mousePressed(MouseEvent e)
    Point p = e.getPoint();
    for(int i = 0; i < labels.length; i++)
    Rectangle r = labels[i].getBounds();
    if(r.contains(p))
    selectedLabel = labels[i];
    offsetP.x = p.x - r.x;
    offsetP.y = p.y - r.y;
    dragging = true;
    break;
    public void mouseReleased(MouseEvent e)
    dragging = false;
    public void mouseDragged(MouseEvent e)
    if(dragging)
    Rectangle r = selectedLabel.getBounds();
    r.x = e.getX() - offsetP.x;
    r.y = e.getY() - offsetP.y;
    selectedLabel.setBounds(r.x, r.y, r.width, r.height);
    determineCenterOfComponents();
    repaint();
    private void addLabels()
    label1 = new JLabel("Label 1");
    label2 = new JLabel("Label 2");
    label3 = new JLabel("Label 3");
    label4 = new JLabel("Label 4");
    labels = new JLabel[] {
    label1, label2, label3, label4
    for(int i = 0; i < labels.length; i++)
    labels[i].setHorizontalAlignment(SwingConstants.CENTER);
    labels[i].setBorder(BorderFactory.createEtchedBorder());
    add(labels[i]);

    If you need some help, be respectful of the forum rules and people will help. By using "urgent" in the title and bumping your message every 2 hours you're just asking to be ignored (which is what you ended up with).

  • Your urgent help will be very much appreciated

    I have a problem whenever I connect my database and need your urgent help. the sample source code is below
    import java.sql.*;
    import javax.swing.*;
    import java.awt.*;
    import java.awt.event.*;
    import java.util.*;
    public class Table extends JFrame
    private Connection con;
    private JTable table;
    public Table()
         String url = "jdbc:odbc:Books";
         String username="";
         String password="";
         try{
         Class.forName("sun.jdbc.odbc.JdbcOdbcDriver");
         con = DriverManager.getConnection(url, username, password);
         catch(ClassNotFoundException cnfex)
         System.err.println("Failed to load JDBC/ODBC driver.");
         cnfex.printStackTrace();
         System.exit(1);
         catch(SQLException sqlex)
         System.err.println("Failed to connect");
         sqlex.printStackTrace();
         getTable();
         setSize(45,150);
         show();
    public void getTable()
         Statement state;
         ResultSet result;
         try{
         String query="Select * from Author";
         state=con.createStatement();
         result=state.executeQuery(query);
         displayResult(result);
         state.close();
         catch(SQLException sqlex)
         sqlex.printStackTrace();
    public void displayResult(ResultSet rs)throws SQLException
    boolean moreRecord=rs.next();
    if (!moreRecord)
    JOptionPane.showMessageDialog(this, "ResultSet contained no record");
    setTitle("No records to display");
    return;
    setTitle("Author table from Books");
    Vector columnHeads=new Vector();
    Vector rows=new Vector();
    try{
    ResultSetMetaData rsmd=rs.getMetaData();
    for (int i=1; i<=rsmd.getColumnCount(); i++)
    columnHeads.addElement(rsmd.getColumnName(i));
    do{
    rows.addElement(getNextRow(rs, rsmd));
    }while(rs.next());
    table=new JTable(rows, columnHeads);
    JScrollPane scroller=new JScrollPane(table);
    getContentPane().add(scroller,BorderLayout.CENTER);
    validate();
    catch(SQLException sqlex)
    sqlex.printStackTrace();
    public Vector getNextRow(ResultSet rs, ResultSetMetaData rsmd)
              throws SQLException
    Vector currentRow=new Vector();
    for (int i=1; i<=rsmd.getColumnCount(); i++)
    switch (rsmd.getColumnType(i))
    case Types.VARCHAR:
         currentRow.addElement(rs.getString(i));
         break;
         case Types.INTEGER:
         currentRow.addElement(new Long(rs.getLong(i)));
         break;
    default:
    System.out.println("Type was: "+rsmd.getColumnTypeName(i));
    return currentRow;
    public void shutDown()
         try{
         con.close();
         catch(SQLException sqlex)
         System.err.println("Unable to disconnect");
         sqlex.printStackTrace();
    public static void main(String args[])
         final Table app=new Table();
         app.addWindowListener( new WindowAdapter()
         public void windowClosing(WindowEvent e)
              app.shutDown();
              System.exit(0);

    Thank you for your help. When I compile it, it is fine, the problem happens when run it.
    Unexpected Signal : EXCEPTION_ACCESS_VIOLATION occurred at PC=0x6d448d54
    Function name=(N/A)
    Library=C:\Program Files\JavaSoft\JRE\1.3.1_05\bin\hotspot\jvm.dll
    NOTE: We are unable to locate the function name symbol for the error
    just occurred. Please refer to release documentation for possible
    reason and solutions.
    Current Java thread:
    at sun.jdbc.odbc.JdbcOdbc.driverConnect(Native Method)
    at sun.jdbc.odbc.JdbcOdbc.SQLDriverConnect(Unknown Source)
    at sun.jdbc.odbc.JdbcOdbcConnection.initialize(Unknown Source)
    at sun.jdbc.odbc.JdbcOdbcDriver.connect(Unknown Source)
    at java.sql.DriverManager.getConnection(Unknown Source)
    at java.sql.DriverManager.getConnection(Unknown Source)
    at Table.<init>(Table.java:26)
    at Table.main(Table.java:145)
    Dynamic libraries:
    0x00400000 - 0x00405000 C:\WINNT\system32\java.exe
    0x77F80000 - 0x77FFB000 C:\WINNT\System32\ntdll.dll
    0x77D90000 - 0x77DED000 C:\WINNT\system32\ADVAPI32.dll
    0x77E60000 - 0x77F35000 C:\WINNT\system32\KERNEL32.DLL
    0x786F0000 - 0x78761000 C:\WINNT\system32\RPCRT4.DLL
    0x78000000 - 0x78046000 C:\WINNT\system32\MSVCRT.dll
    0x60000000 - 0x6003A000 c:\program files\rising\rav\ApiHook.dll
    0x05000000 - 0x0502E000 c:\program files\rising\rav\MemMon.dll
    0x77DF0000 - 0x77E55000 C:\WINNT\system32\USER32.dll
    0x77F40000 - 0x77F7C000 C:\WINNT\system32\GDI32.DLL
    0x75E00000 - 0x75E1A000 C:\WINNT\System32\IMM32.DLL
    0x6D420000 - 0x6D4F7000 C:\Program Files\JavaSoft\JRE\1.3.1_05\bin\hotsp
    ot\jvm.dll
    0x77530000 - 0x77560000 C:\WINNT\system32\WINMM.dll
    0x6D220000 - 0x6D227000 C:\Program Files\JavaSoft\JRE\1.3.1_05\bin\hpi.d
    ll
    0x6D3B0000 - 0x6D3BD000 C:\Program Files\JavaSoft\JRE\1.3.1_05\bin\verif
    y.dll
    0x6D250000 - 0x6D266000 C:\Program Files\JavaSoft\JRE\1.3.1_05\bin\java.
    dll
    0x6D3C0000 - 0x6D3CD000 C:\Program Files\JavaSoft\JRE\1.3.1_05\bin\zip.d
    ll
    0x6D020000 - 0x6D12A000 C:\Program Files\JavaSoft\JRE\1.3.1_05\bin\awt.d
    ll
    0x777C0000 - 0x777DE000 C:\WINNT\system32\WINSPOOL.DRV
    0x75010000 - 0x75020000 C:\WINNT\system32\MPR.DLL
    0x77A30000 - 0x77B25000 C:\WINNT\system32\ole32.dll
    0x6D1E0000 - 0x6D21B000 C:\Program Files\JavaSoft\JRE\1.3.1_05\bin\fontm
    anager.dll
    0x6DD30000 - 0x6DD36000 C:\WINNT\System32\INDICDLL.dll
    0x37210000 - 0x3723D000 C:\WINNT\DOWNLO~1\CnsMin.dll
    0x77C50000 - 0x77C9A000 C:\WINNT\system32\SHLWAPI.dll
    0x777E0000 - 0x777E7000 C:\WINNT\system32\VERSION.dll
    0x75950000 - 0x75956000 C:\WINNT\system32\LZ32.DLL
    0x6D290000 - 0x6D29A000 C:\Program Files\JavaSoft\JRE\1.3.1_05\bin\JdbcO
    dbc.dll
    0x1F7F0000 - 0x1F825000 C:\WINNT\system32\ODBC32.dll
    0x76AF0000 - 0x76B2D000 C:\WINNT\system32\comdlg32.dll
    0x77B30000 - 0x77BB9000 C:\WINNT\system32\COMCTL32.DLL
    0x78F90000 - 0x791D6000 C:\WINNT\system32\SHELL32.DLL
    0x1F8E0000 - 0x1F8F6000 C:\WINNT\system32\odbcint.dll
    0x77900000 - 0x77923000 C:\WINNT\system32\imagehlp.dll
    0x72960000 - 0x7298D000 C:\WINNT\system32\DBGHELP.dll
    0x687E0000 - 0x687EB000 C:\WINNT\system32\PSAPI.DLL
    Local Time = Tue Feb 25 21:33:38 2003
    Elapsed Time = 7
    # HotSpot Virtual Machine Error : EXCEPTION_ACCESS_VIOLATION
    # Error ID : 4F530E43505002BD
    # Please report this error at
    # http://java.sun.com/cgi-bin/bugreport.cgi
    # Java VM: Java HotSpot(TM) Client VM (1.3.1_05-b02 mixed mode)
    # An error report file has been saved as hs_err_pid1792.log.
    # Please refer to the file for further information.
    #

  • URGENT HELP NEEDED (Bios Settings Failed)

    Hey Guys,
    I am having problems with my MSI Board, and don't know what to do.  I am very much a noob to BIOS/and modding so I apologize in advance.  You guys helped me a few months ago getting everything up and running and all was great for months.  Then last night I walked away from my PC for a while and when i came back a starting screen was on saying my OC Settings Failed to load, i tried other versions I saved and they all failed as well.  I ended up loading failsafe options, and got the "double start" where the computer turns on, then instantly shuts off, then turns on again.  This allowed me to load windows 7, which then started to "install updates".   So i think while i was away Windows automatically updated and rebooted... but would that effect my BIOS settings?
    As I said, I had my system running perfect for months no errors or crashes at all based on the Bios setting you guys help me with in this thread:  https://forum-en.msi.com/index.php?topic=147854.0
    However, last week I removed the heat sink and installed this cooler:  http://www.newegg.com/Product/Product.aspx?Item=N82E16835181010&nm_mc=OTC-Froogle&cm_mmc=OTC-Froogle-_-Water+Cooling-_-Corsair-_-35181010
    All I did was unhook everything from the MB, install the cooler, and then hook everything back up to the MB.  The only thing I may have done wrong is not connect the SATA devices (my HDs and ROMS) back in the spots they were in originally.  However after I installed the cooler, they system booted right up, and I haven’t had any problems with my system for the past two weeks.  I also should note I didnt make any BIOS changes either after I installed the cooler.  So I don’t know if I should have done something there.   Yet, like I said the system has been fine for the past two weeks, no crashes or errors... it wasn’t until last night after Windows auto updated that this has begun.
    The reason I need "URGENT HELP" is because of course I just a new job with deadlines due and so much video editing work I need to do.  I would be fine leaving it on failsafe settings, and forgetting the OC setting all together if I new that would make the system stable.  But considering its still doing the "double start" even in failsafe mode, im afraid if i start working my system will crash.
    So I am begging anybody for any advice or help they could provide.  I will provide my system info below.  If anybody can guide me as to what settings I should set in BIOS i would appreciate it.  Or perhaps there’s a BIOS update that I should use now that I have a cooler and not a heat sink?  If you need any more information from me, just ask.  I will be monitoring this thread all day, as I desperately need help.
    MY SYSTEM: 
    Intel 980X chip running Win 7 64bit (with MSI BigBang xPower MB installed in my old Dell XPS 730X)
    (1) SATA II WD 3gb Hard Drive @ 1.5TB
    (2) OCZ SATA II SSD drives @120GB: http://www.newegg.com/Product/Product.aspx?Item=N82E16820227543
    (2) Hitachi 6gb SATA III drives @2TB: http://www.newegg.com/Product/Product.aspx?Item=N82E16822145473
    3 DVD/CD/BLUERAY DRIVES:
    1 SATA DVD DRIVE
    1 SATA BlueRay Drive
    1 SATA CD Drive
    (So 8 SATA Devices Total)
    24GIGs of this ram: http://www.newegg.com/Product/Product.aspx?Item=N82E16820145321
    1 NVida Geforce GTX 470
    1 Soundblaster X-Fi Titanum Card
    New Addition Water Cooler:  http://www.newegg.com/Product/Product.aspx?Item=N82E16835181010&nm_mc=OTC-Froogle&cm_mmc=OTC-Froogle-_-Water+Cooling-_-Corsair-_-35181010 

    PROBLEM:  My OC BIOS setting wont load.  Even on failsafe i get the "double start".  I want to get back to my OC (stable) settings.
    UPDATE:  Since I posted somebody messaged me mentioned I should have "reset the CMOS" after I installed the new cooler.  So I did that, and now they system starts fine without the "double start".  I am able to load one of my saved OC settings now as well (but any others causes a failure).
    NEW QUESTIONS: 
          1.  Since I reset the CMOS and now the system is starting fine on my last OC settings, is it safe to assume the sytem is stable for now? 
          2.  I never made any power changes or BIOS changes after I installed the new cooler.  Should I have?
          3.  After I reset the CMOS was I soupposed to reinstall the drivers from the MSI disk again?  I did not, and the system seems to be fine, but I thought I was soupposed to do that after a CMOS reset.
          4.  Is there a new BIOS version for my setup that may be better now?   Im currently on v1.5
    Here is a screenshot from CPUZ of the system information currently.  This is with it booting normally after my CMOS reboot.  I just figured id post it incase it helps with any of my questions.  Thanks so much for helping guys!

  • URGENT HELP NEEDED!!! iOS8 behaviour!

    We have 2 iPhones (6 & 5s) and an iPad using the same Apple ID. Both are running iOS8.
    When someone calls either of the iPhones BOTH iPHONES RING!!!!
    Yes, you read right, the same incoming call appears on BOTH iPhones at the same time.
    This is obviously totally unacceptable not to mention useless.
    Obviously both iPhones use the same account so that iCal & Contacts can be shared but sharing phone calls?
    Really, I need some urgent help with this bug!!!!

    Hi RexRox,
    Based on your description, it sounds like you may have Continuity enabled, a feature in iOS 8 that allows you to take calls across more than one device (generally aimed at a single person with multiple devices on the same account). You may find the following article helpful, especially the following portion:
    Turn off iPhone cellular calls
    To turn off iPhone Cellular Calls on a device, go to Settings > FaceTime and turn off iPhone Cellular Calls.
    Connect your iPhone, iPad, and iPod touch using Continuity
    Regards,
    - Brenden

  • Urgent Help Needed: ATI Graphics Card install

    Hello All.... I am in need of some urgent help..
    I am trying to install a new graphics card - the ATI Radeon 9600 SE. I currently have a Voodoo3 card. I followed all of the instructions step by step, but when I plug the monitor to the Radeon card and boot up, I do not get any display. I have tried everything I can think of, and yet - I am sure the card is secured in place and the monitor is plug into the card.
    Can anyone help me on this one.. ATI's support is, well - lacking..
    Here is some info on my pc:
    MCI motherboard
    AMD Athlon(tm) XP 2000+ 1.7 GHz
    768 MB
    AMIINT - 10 Version 1.00, 07/10/02
    Could the problem be with switching from a regular PCI card to an AGP card???

    Quote
    Originally posted by southmike
    okay i'll bite what are omega drivers,
    how are they different from cat4.2 drivers
    i was suprised that the voodoo 3 would work in a AMD64 mobo...
    whoops....just read the rest of the post :lol:
    BTW is there an external power connector that needs to be plugged in?

  • URGENT HELP REQUIRED!

    I am having problems implementing a username validaion bean for my login system. Every time I click my login icon on my main JSP page the login JSP page does not appear except one of the error JSP pages.
    How can I correct this problem?
    Does the code below look correct?
    Below is the codes for the Username Validation Bean :
    LOGIN.JSP
    <%@ page import="java.io.*"%>
    <%@ page import="java.util.*"%>
    <%@ page import="java.sql.*"%>
    <%@ page import="com.mysql.jdbc.*"%>
    <%@ page errorPage="badLogin.jsp"%>
    <%@ page import="gcd.UserNameValidationBean"%>
    <%
    Class.forName("com.mysql.jdbc.Driver");
    java.sql.Connection connection=java.sql.DriverManager.getConnection("jdbc:mysql://localhost/gcdBB_db");
    java.sql.Statement statement = connection.createStatement();
    Enumeration parameters = request.getParameterNames();
    if(parameters.hasMoreElements())
    String usernameValue = request.getParameter("username");
    String passwordValue = request.getParameter("password");
    statement.executeUpdate("INSERT INTO users (username,password) VALUES ('"+usernameValue+"','"+passwordValue+"')");
    %>
    GOODLOGIN.JSP
    <%@ page errorPage="badLogin.jsp"%>
    <%@ page import="gcd.UserNameValidationBean"%>
    <% UserNameValidationBean validationBean = new UserNameValidationBean();
    if(request.getParameter("username")!=null)
    validationBean.validateUserNameBean(request.getParameter("username"));
    %>
    <%=request.getParameter("username")%>
    USERNAMEVALIDATIONBEAN.JAVA
    package gcd;
    public class UserNameValidationBean
    public UserNameValidationBean(){}
    public boolean validateUserName(String userName) throws InvalidUserNameException
    if(userName.length() < 32)
    throw new InvalidUserNameException("User Name Invalid: " + userName);
    return true;
    INVALIDUSERNAMEEXCEPTION.JAVA
    package gcd;
    public class InvalidUserNameException extends Exception
    public InvalidUserNameException(String message)
    super(message);
    I need urgent help to get this working!

    Here is code for badLogin.jsp and badLoginWithExceptonObject:
    BADLOGIN.JSP
    <HTML><HEAD><TITLE>Login Failure</TITLE></HEAD>
    <BODY bgcolor="#FF9900">
    <H1></H1>
    <font face="Arial" size="3">Sorry but you either entered an incorrect username
    or password </font>
    <P><font face="Arial" size="3">Try Again</font>
    </BODY></HTML>
    BADLOGINWITHEXCEPTIONOBJECT.JSP
    <HTML><HEAD><TITLE>Check User Login Against Parameters</TITLE></HEAD>
    <BODY bgcolor="#FF9900">
    <%@ page isErrorPage = "true"%>
    <P><font face="Arial" size="3">Error =</font> <%= exception.getMessage()%> <% PrintWriter writer = new PrintWriter(out); %>
    <P><font face="Arial" size="3">Stack =</font> <% exception.printStackTrace(writer); %>
    <P><font face="Arial" size="3">Try Again</font>
    </BODY></HTML>

  • Urgent help required in migration

    Hello,
    I am stuck on 77% of r3load process my all 15/16 processes are finished successfully only one process has failed I have cut paste the log (SAPAPPL1.log) below of the same. Request your urgent help.
    DbSl Trace: Connecting via TNS_ADMIN=/oracle/F01/920_64/network/admin, tnsname=F01
    DbSl Trace: Got NLS_LANG=AMERICAN_AMERICA.US7ASCII from environment
    DbSl Trace: Now I'm connected to ORACLE
    DbSl Trace: Database instance F01 is running on e027pae0 with ORACLE version 9.2.0.7.0
    trying to restart import ###
    (RIM) INFO: table "BKPF" truncated
    restart finished ###
    #START: 20070530101004
    TAB: BKPF
    (RD) ERROR: missing last block number for table "BKPF" in directory file "/sapcd/EXPDIR/DATA/SAPAPPL1.TOC"
    #STOP: 20070530101004
    Thanks & Regards,
    Bhushan

    Did you split the files?
    It seems that export file for this table got corrupt.
    Unfortunately, you ahve to start again. I had a similar problem and had to do it again.

Maybe you are looking for