USB 2.0 on K7N2 Delta ILSR

Hi there !
I have a problem with USB 2.0 on my motherboard.
I understand now I need Win XP Service PAck 2 loaded to be able to get the USB 2.0 support.
I installed a few month ago the Nvivia drivers (coming from the nvidia web site), and my USB port is working finr.
Today; Windows update is proposing to install service pack 2 (It was not installed yet). I just installed it, but what should I do for USB 2.0 support ?
Reload the nvidia Drivers ?
How can I check I have USB 2.0 now or USB 1.0 ?
Many Thanks!!

Quote from: cdelecole on 27-December-05, 01:58:01
Concentrateur USB Racine
Concentrateur USB Racine
Concentrateur USB Racine
Controleur hote PCI vers USB Standard etendu
Controleur hote USB OpenHCD Standard
Controleur hote USB OpenHCD Standard
not that i know any french, but i am guessing by comparing to mine that "etendu" translates to "enhanced",
and according to this page, having the word "enhanced" in there is all the verification you need.
(mine is working and reads "standard enhanced pci to usb host controller")

Similar Messages

K7N2 Delta-ILSR - USB to Serial Adapter Doesn't Work!

Is anyone aware of an error such as the follows with the K7N2 Delta-ILSR?
I am trying the use a USB to Serial Adapter, namely the a Prolific PL-2303.
However, my PC does not seem to like it, nor does it what to cooperate with it at all.
On one occasion i have managed to get the device to show in the Manager window with the exclamation mark,
and upon checking its properties it told me: Prolific This device cannot start. (Code 10).
I have un-installed all my system USB drivers and the device drivers, and reinstalled them, but again, no matter what i do i cannot get it to work.
Any ideas peeps?
Cheers, G.

Don't think it will this time, but on occassions booting into SafeMode and removing possibly half-installed copies of USB devices from Device Manager has helped.
Is this what you are looking for, Henry?
http://www.prolific.com.tw/eng/downloads.asp?ID=33
"Note: Please take notice of the installation order. First, run the InstallShield wizard,
and then plug in the USB to Serial adapter"
...How many times have I said that, if a USB device needs a driver you install that before attaching the device!?

K7N2 Delta ILSR & Netgear MA311

Please help!
K7N2 Delta ILSR
AMD 2500+ not over clocked
ATI 9600 Pro 256Mb graphics not over clocked
768Mb RAM - not labelled
300Watt PSU
Netgear MA311 PCI Wireless network card
Win XP
Everything works fine bar the Netgear wirless network card. I am getting "The device cannot start. (Code 10)." in Device Manager.
Tried the latest drivers from Netgear. Done a windows update. Updated the BIOS. Tried all the PCI slots. Disabled EVERYTHING (inc on-board network, serial, paralell, usb etc) but the bare bones in the BIOS. Updated from MSI site the system drivers.
Tried the card in my other machines & works fine.
I'm stuck & any assistance would be greatly appreciated.
Paul

The IRQ table looks like this:
(ISA) 0 System timer
(ISA) 1 Stadard Keyboard
(ISA) 3 COM2
(ISA) 8 System CMOS/realtime clock
(ISA) 9 Microsoft ACPI-Compliant System
(ISA) 13 Numeric data processor
(ISA) 14 Primarary IDE Channel
(ISA) 15 Secondary IDE Channel
(PCI) 4 NVIDIA(R) nForce(TM) MCP Audo Processing Unit
(PCI) 5 NVIDIA nForce PCI System Management
(PCI) 5 NVIDIA(R) nForce(TM) Audi Codec Interface
(PCI) 10 NVIDIA nForce MCP Networking Controller
(PCI) 10 Standard OpenHCD USB Host Controller
(PCI) 11 Standard Enhanced PCI to USB Host Controller
(PCI) 11 WinXP Promise FastTrack 376 (tm) Controller
(PCI) 12 Rdeon 9600 Series
(PCI) 12 Standard OpenHCD USB Host Controller
Rgds
Paul

Using extenal HDD with K7N2-Delta ILSR

My board is MS-6570 K7N2 Delta ILSR. My board supports up to 160GB HDD. But i want to buy a 400GB external Philips USB 2.0 HDD. Does my board support this?

tsavasci,
Please don't use liveupdate to flash a bios...just too fickled and risky. In the future, if you need to flash an MSI board, use a bootable CD or, better yet, try the USB flashing utility we have developed.
clickme>>MSI Forum HQ USB flashing tool!!!<<clickme

K7N2 Delta ILSR (mouse stuttering)

:wall:windows/load/mousepointer/trouble:bonk:
if windows is running under load,even if load means that i just
use windows media player or any other application, the
pointer is starting to stutter alot. if i stop media player, the
mouse runs fine again.
meanwhile i read many threads that doesn't helped me.
meanwhile i read several nforce2 problem guides.
meanwhile i checked out all thinkable ways of changing values
on mobo and in windows itself. i had no success.
tried changing drivers, programs, operating systems and
some parts of hardware.
all you can imagine, i guess. i'm not a noob.
i'm out of ideas .... anybody got a hint to help me?
* otherwise the k7n2 delta ilsr is the worst mobo i ever got*

@Wonkanoby
IRQ TABLE : (without using APIC) / with ide sw miniport driver
(ISA) 0 system timer
(ISA) 1 standard 101/102-key or ms natural ps/2 keyboard
(ISA) 3 communications port (com3)
(ISA) 6 standard floppy disk controller
(ISA) 8 system cmos/real time clock
(ISA) 9 microsoft acpi-compilant system
(ISA) 12 ps/2 compatible mouse
(ISA) 13 numeric data processor
(PCI) 4 nvidia(r)nforce(tm) MCP audio processing unit (dolby(r)digital)
(PCI) 5 nvidia geforce fx 5600
(PCI) 5 standard open hcd usb host controller
(PCI) 7 nvidia nforce pci system management
(PCI) 7 nvidia(r)nforce(tm) audio codec interface
(PCI) 10 nvidia nforce MCP networking controller
(PCI) 10 standard open hcd usb host controller
(PCI) 11 standard enhanced pci to usb host controller
(PCI) 14 nvidia nforce 2(tm) spp/igp ata controller
(PCI) 15 nvidia nforce 2(tm) spp/igp ata controller
IRQ TABLE : (using APIC) / without ide sw miniport driver
(ISA) 0 system timer
(ISA) 1 standard 101/102-key or ms natural ps/2 keyboard
(ISA) 3 communications port (com3)
(ISA) 6 standard floppy disk controller
(ISA) 8 system cmos/real time clock
(ISA) 9 microsoft acpi-compilant system
(ISA) 12 ps/2 compatible mouse
(ISA) 13 numeric data processor
(ISA) 14 primary ide channel
(ISA) 15 secondary ide channel
(PCI) 7 nvidia nforce pci system management
(PCI) 19 nvidia geforce fx 5600
(PCI) 20 nvidia(r)nforce(tm) audio codec interface
(PCI) 20 standard enhanced pci to usb host controller
(PCI) 21 nvidia nforce MCP networking controller
(PCI) 21 standard open hcd usb host controller
(PCI) 22 nvidia(r)nforce(tm) MCP audio processing unit (dolby(r)digital)
(PCI) 22 standard open hcd usb host controller

2 Queries on K7N2 Delta-ILSR

Hi,
1) I just bought a pair of K7N2 Delta-ILSR mobo's for two new pc's. Each box has in it an item that isn't mentioned in the book, on the box, or at the website. It's for a rear slot, and it has two ports on it. One looks like an RCA jack, the other is five hole round (looks similar to a mouse port). There's a black cable with a rectangular five hole connector on the end.
Anyone know ehat it is?
2) I feel stupid even asking this. There's an nforce2 chip on the board, which I'm told is equivalent to a geforce 3 card. Where does a monitor get plugged in to?
Thanks!!!!
Paul

I believe its a TV out that was included by mistake, there is an answer in a FAQ I read tonight on the MSI site. There is no GeForce on the K7N2 Delta-ILSR, you need the "G" version for that.
As I just got my Delta tonight I will ask a couple of questions here Im unsure about instead of making a new thread up.
First Im using my XP2400 266mhz until I can afford a new CPU but Im using some 333mhz Ram, will this be ok and whats the best settings will I have to run the ram at 266 or can I run it at 333mhz? BTW I have used the 333 in my 420 ok with the xp2400 but with this Delta accepting a higher memory type Im unsure how it will pick it up in any settings.
Also I notice an extra 4pin CPU ATX power connecter, do I have to use this as well as the normal ATX connector?
Finally, is the covered Bluetooth port just a bog standard USB connecter?
thanks for any answers
waveydavey
#

Win XP problem w/k7n2 delta ilsr

I forgot to put this in my first post. I have a k7n2 delta ilsr and I'm using win xp pro. In device manager under Other Devices it reads:
? ethernet controller
? raid controller
? sm bus controller
? universa serial bus usb controller
Did I forget to install or setup something.
Thanks, Ron.

Hi,
Yes, you should install the nForce drivers for your board:
The latest ones are here:
http://www.nvidia.com/content/drivers/drivers.asp
Axel

Case Recommendation for K7N2 Delta-ILSR

Greetings,
I'm looking for a mid size ATX case that that has the front usb etc. ports prewired as to work easily with a K7N2 Delta-ILSR mb. By that I mean I don't have to plug each wire individually (with names that don't match) just a plug that goes on the mb. My eyesight isn't as sharp so hooking up those one wire at a time is tediuous. Not to mention the lack of starndards Does anyone know if this is address on the next rev of mb's (with pcix etc).
Thanks

Brazos,
I have yet to see a case that has all the USB wires together, they are all 1 pin at a time. You will find the Antec line of cases very good. (You can always use a magnifying glass to see the pins.) The pin names on the Antec cases are standardized and easy to figure out.
If you want a good case at a cheap price, then go with the SLK3700AMB:
If you want a good high end case, then go with the Sonata:
If weight is an issue, then go with the Super Lanboy:
Take Care,
Richard

Someone plz help me with my k7n2 delta-ilsr

Hey everyone,
I just put my sytem togother and ran into a problem. I got the system to boot up just fine. It was not until I tried installing windows xp proffesional that I ran into problems. The installation process runs pretty smoothly, until the computer reboots to run windows for the first time. After it reboots the windows logo appears and the after 2 seconds or so, a blue screen appears saying that windows was shut down to prevent any damage to my computer. I have never encountered this problem before when I built other systems. The screen suggests that I should check my HDD's for viruses or check to see if they are configured correctly. The HDD's are SATA and I have them set up in RAID 0 mode and yeah I installed the RAID drivers during the installation process. Thinking that I had made mistake setting up the SATA drives, tried installing windows using a regular IDE hard drive and it gave the same message. I am stumped anybody have any ideas of what I might be doing wrong? Any help would be appreciated . My system specs are below.
MSI k7n2 delta-ilsr mobo
AMD 3000+ Athlon XP cpu (333 fsb)
ATI Raedon 9000 ( I know it's crappy , I'm still saving up for the ATI all in wonder 9800 )
x1 kingston 512mb pc3200 DIMM
x2 maxtor 80gb maxtor hdd's
x1 regular cd-rom drive
x1 floppy drive
420w raidmax psu
(+3.3v = 26A, +5v = 32A, +12v=13A)

Memory that comes with timing of 5 2 2 2 or 6 2 2 2 or usally winbond BH-5 memory chips. Ones with 5 3 2 2 or CH-5 winbond chips. The BH-5 chips overclock a little better than the CH-5. (Muskin uses BH-5 winbond in there black ram)
Winbond is no longer making BH-5 chips but is going to make a limited run of them as demend is high for them.
The first number shown here is the Traz and it controls the flush timing bench testing is showing that a higher number of 9, 10 or 11 or getting better bench results than the 6 or 5. Thats with Dual Channel memory.
The timing you show probly should be something like 8 3 3 3 or 8 3 3 2.5 unless it is there faster Dual channel ram.
The timing numbers can also appear like this 2 2 2 5 the high number is the Traz either way.
Look on your memory manufactor web site for the timing that if should run at also look at the voltage as this can make a big differance.

HELP me with my K7N2 delta ilsr

Can anyone help me with this problem. I have just upgraded to MSI's K7N2 delta ilsr motherboard. Its all working quite well apart from the fact that the pc wont start up from cold....at all.
When I start the pc from an off state, it runs up the fans and drives, but does not post.
The diagnostic led pannel on the back of the pc shows that the cpu is faulty or not installed correctly.
If I then press the reset button, the pc posts, and boots up just fine.
It does this EVERY time I start up.
I have tried re installing the cpu, which is an XP 2800+ 333 barton, but to no avail.
I have asked a few questions on other forums, but I cant solve it.
These are the suggestions so far.
1. the psu (I have a Tsunami 400 atx psu) could not be giving out enough power on initial startup, but once the pc is running, it has enough to boot the pc from a reset.
2. The mobo or the bios could be at fault. I have not flashed the bios, or upgraded it in any way from original, so is there an issue with the original bios on these boards, and 2800 barton chips??? Could it be a mobo fault? The pc runs fine once the machine is booted.? how do I test it?
3. The cpu could be faulty? but would this not stop it running fuull stop?
4. my ram. I have a single stick of OCZ 512mb pc3200 ddr, which I was told would make the pc fly. Not shure on that statement, but is this ram compatible?? could this be the problem?
Im fairly new to the upgrade side of things, and I need some help with this one.
Also, Id be really greatfull if some one could talk me through flashing my bios to the latest version, as the thought of doing this narks me a bit...I dont want to mess it up and get a dead pc...
HELP

+3.3v 14A
+5v 28A
+12v 16A
+5vsb 2A
-5v 0.5A
-12v 0.8A
Hope this helps, as my pc seems to be living with its case off a lot these days..haha

Internet Connection Problem on MSI K7N2-Delta-ILSR

Hi, recently I buy an MSI K7N2-Delta-ILSR.I have a problem when I was trying to connect to the Internet through my modem on WinXP Pro SP1. It bring me up an error message 678 ( The computer that was tried to connect did not respond...). I have also a second hard disk with Mel windows. On disk the disk with the Mel I don’t have any problem with the internet connection. All my settings are same on WInXP pro and Mel.I have checked I thousand times. My computer configuration is:
Athlon XP 2400+ Overclocked to 2205MHz
2 memory modules of 256MB 400 manufactured by Samsung
TharmalTake Volcano 11
Triplex Xabre 400 PRO with 128MB
Hercules Gamesurrround Fortissimo III 7.1
Microcom InPorte Home modem 56k
Leadtek winfast 2000 (TV/FM radio)
Acard SCSI controller (Acard AEC-6710D) for my scanner
WesternDigital WD800 GB
WesternDigital 15.3gb
Bios ver.7.4
Can anyone help me?

Quote
Originally posted by Roger Wilco
Hmmmmm, I\'m also having a problem with the onboard lan of the K7N2 Delta.
I have an ADSL connection, and have an Alcatel SpeedTouch Home modem.
I pretty much get the same error as SiliconMan (The computer that was tried to connect did not respond...)
I ended up giving up on it for the time being, just using my SMC NIC. Would be quite interested in finding out what the problem is though.
Anyone else in the same boat?
Hi,
Your problem is not the same, SiliconMan is trying to connect with a dial-up modem not LAN. Your problem sounds like it may be configuration, do a search on this post, I'm sure you will find people with onboard LAN troubles. It's hard to troubleshoot though since you didn't provide any info about your computer. Good Luck
Rob

Strange phantom restarts on MSI K7N2 Delta ILSR

Just wanted to see if I could get opinions on this. My MSI K7N2 Delta ILSR mobo runs real nice now, but still, on occasion, very rare and intermittently, it will just restart. Not likely a heat issue, as the temps are nice and low. Also, not just happenning when I'm playing a game or anything strenuous. Did it once while checking email, once during install of an MS Office program, and once during a game. Could it be my old Gforce 2 MX 200 video card, as the picture sometimes gets wavy (like fine waves on an ocean), and the old computer it was in did similar things, or is it common with this mobo.
MSI K7N2 Delta ILSR
Athlon XP 2500+ Barton
1026 MB Kingston DDR RAM (2x512 Dual)
Gforce 2 MX 200 AGP 4x
WD 60 GB 7200 RPM

I had errors on test 4 not 5 with Winbond 2-512 Dual Channel called Hardcore Cooling and they said that getting errors with memtest86 may not mean that the ram is defective, it may not be compatible with the memory comtrol and they had me RMA it back. I also was not able to run the ram stable at there advertized rate of 6 2 2 2 it was only stable at 8 3 3 2.5
I replaced it with OCZ after talking to there Tech support people about compatiblety problems with the Nvidia chipset. Sense I installed the OCZ I only had one ram reboot and when I checked I was running the voltage at 2.5 and OCZ said that I should be running at 2.6. They also said that I could run it up to 2.8 with no worry.
Look on manufactor web site to see what ram timing yours should be running at and what voltage, Auto setting in Bios is not always the best setting.
If it still not stable at manufactor spec than I'd talk to who ever you bought it from about replacing it or refund and buy something thats on the Nvidia compatible list.
Most ram manufactors have a list of motherboards that there ram will work on but sometimes the newer boards like K7N2 or not listed yet as still working that out.

Kate needs HELP!!! MSI K7N2 Delta ILSR

Guys...
pls help me...
I am assembling, yes I know I am a techi girl...., msik7n2 with radeon9600 and 2xCorsair Value Select 256Mb DDR 400Mhz PC3200 mem...(hence 512mb)
I installed everything assembled it... booted and loaded fine for about 3 times...
and suddenly....
>power on
>no video
>no beeps
>after checking hard nothing happens...
>only thing I can tell is that the d bracket is indicating "memory section"
....d-bracket from MSI K7N2 Delta ILSR is 1,3,4 red and 2 green. Which is according the the manual "Memory Detection Test"-if the memory module is damaged or not installed properly.
Why woudl a memory suddenly not work?
I know I was adjusting bios for this and that....
I think just before this happened.. I adjusted something on agp setting... but what ahs that got to do with memory?
COuld it be the mobo or memory or the video card???
pls help....
My email is [email protected]...
please please help...
and guys in MSI what is your expert opinion? mobo? or memory?
Heeeeeeeeeeeeeeeellllp...
thanks...
Kate x

hi and welcome to this forum.
nice to se a girl here for a change
clear cmos jumper jbat1.
also try safe mode jumper j10 ans j11.
also try to reseat memory and dont trust the dbracket to 100%.
it can show wrong sometimes.
Quote
COuld it be the mobo or memory or the video card???
when you got it running then run http://www.memtest86.com to check memory,
also what psu do you have ?
post max amps on 3.3v 5v and 12v rails.
minimum is 28 35 16.recommended is higher.

Data corruption on MSI K7N2 Delta ILSR

Hi all,
Just got my new MSI K7N2 Delta ILSR up and running.
Got some issues with the memory running at 200mhz while the Barton core of my Athlon Xp 2600+ was running 166mhz, this had to be 1:1 (thx forum )
While running the default bios settings with cpu/mem at 166/166 fsb everything is stable as hell. I have been running Prime95 for 2 days now and using the system for dvd ripping/encoding, UT2004 gaming etc.
Then the overclocking began I'm using the standard AMD cooler that came with my boxed Xp2600+ so I didn't expect an FSB of 200mhz.
I stopped at an FSB of 190mhz...been crunching Prime95 for 18 hours now and again very stable.
Now comes the problem : Sometimes I get crc errors when installing a game or decrypting a dvd!! But how can this be? Prime95 is stable at this 190fsb overclock.
When using an FSB of 166mhz no data corruption or crc errors.
What can this be? It's not the cables because they're all the same as in my old setup which was running (ahum...walking) stable. PCI/AGP speeds are locked when overclocking...
Only thing I can think of is the power supply. I've read in a warning post from Bas that the Q-Tec 550w psu I have is crap. So my guess is PSU, but maybe it's something else I'm forgetting...Any suggestions??
The stupid thing is when I'm not overclocking I don't have the data corruption problems, but I'm still using the same crappy Q-Tec 550w PSU.
Help!
gr,
Remco

Hmmm, that's curious. On the MSI K7N2 Delta ILSR product page Kingston memory is recommended
Ok, did a Memtest86 v1.11 pass at cpu/dimm 166/166 - no problems whatsoever. I think using Prime95 would have revealed memory problems...but will do another pass with cpu/dimm at 190/190.
Can overclocking affect the Promise Raid Controller?? It should be locked like the PCI/AGP but who knows...
Well, I still have to replace my PSU but I'm not 100% sure that this is the problem. What PSU would you recommend? ...and I'm also thinking about replacing the standard CPU cooler, any advice is welcome
gr,
Remco

FLASH BIOS MSI K7N2 Delta-ILSR ????????

I am trying to flash the BIOS of my K7N2 Delta-ILSR board. I follwed all the instructions from the MSI Web but I can't get it going. I booted from Win ME & Win98 but could not get into C: drive. So I used Command Prompt from Window to get into the C: drive and follwed the Flash Bios Procedures. I keep getting the message: AwdFlash No Support WinNT/2000/XP OS
I got problem with the temp after I updated the BIOS. I wanted to flash it back to the old Bios. Please help me out
Thank you
My system:
WinXP Pro
MSI K7N2 Delta-ILSR
AMD 2500+
1 GB DR3200
Seagate 160 SATA

http://www.msi.com.tw/html/support/bios/note/ntfs.htm

USB 2.0 on K7N2 Delta ILSR

Similar Messages

Maybe you are looking for