Using Airport Extreme base station as wireless Cable router and airtunes.

Can I replace my wired Roadrunner cable modem with a Apple Airport Extreme wireless 56g router removing the wired modem out of the picture?
I just have read and have not come to the complete conclusion that the Airport extreme base station is a standalone wireless router.
I would like this if it is a wireless standalone router as I want to but a pair of wireless airtunes router for music around the house keeping the Airport Extreme in my room where the airtunes routers would not be as I have the computer in my room and I have iTunes right there and would not need the airtunes routers in my computer room.
Leon.

Can I replace my wired Roadrunner cable modem with a Apple Airport Extreme wireless 56g router removing the wired modem out of the picture?
The AirPort Extreme Base Station (AEBS) does NOT have a built-in DSL/Cable modem. You will still require a Cable modem in order to access your ISP's Internet service.
I just have read and have not come to the complete conclusion that the Airport extreme base station is a standalone wireless router.
The AEBS IS a wireless router, but it is NOT a combination wireless router & cable modem.

Similar Messages

Trouble using Airport Express Base Station with DSL modem, Router and Hub

About 18 months ago, I had an Airport (802.11b) with WAN & LAN ports and modem hooked up to support two laptops, a Titanium Powerbook G4/600 and G3/400. The setup went from DSL modem -> Linksys router -> to Airport -> Hub (which had desktop and ethernet laser printer plugged in). The network worked fine.
Then, I got a G4 iBook to replace G3/400. Wanted to get 802.11g to support “g” Airport card in iBook. Got a Linksys 802.11g Wi-Fi with 4-port router for $50. Hooked it up directly with DSL modem. (Couldn’t get it to send out to hub). Hooked the desktop and ethernet laser printer into Linksys Wi-Fi/router. The only way I could use the printer was by having it be a shared printer from the desktop. This was often problematic.
Two months ago, I got a refurbished Airport Extreme Base Station. I can’t get the AEBS to interface directly with the DSL modem, so I hooked it up as follows:
DSL modem -> Linksys router -> to AEBS -> Hub. I plugged my Epson 820 (USB) into the AEBS and can see it to print to.
I have a static IP. That info is entered into Linksys router. Router set as Gateway, with DHCP enabled. AEBS is set to Connect using Ethernet, Configure using DHCP. Network setting: Distribute IP Addresses is unchecked.
Here’s my issue:
I can’t see the ethernet laser printer. It will occasionally flash available, but is gone in less than a minute. The printer is HP 2100 series.
Sometimes I can connect to the desktop G4 tower; most times I can’t.
I have checked and double-checked the cables.
Both the printer and desktop are connected to the Hub.
What can I do so that I can see the HP 2100 series printer and the G4 tower?

Don,
Thanks for the suggestions. Glutton for punishment that I am, I tried this again, “just for grins.“ The six other times I tried this, I couldn’t get the AEBS to “see” the Internet. And lo, this time it worked. Here’s the setup now:
DSL modem -> AEBS -> 4-port hub (which is connected to G4 tower and HP 2100 Ethernet printer). My USB Epson is connected to the AEBS, and I can print from the laptops. AEBS is set up: manual IP info, Network: distribute IP address; share a single IP using DHCP.
When I still couldn’t see the desktop G4 and the Ethernet HP 2100 connected via the hub (not), I got a flash. I had swapped out the cable a number of times to no avail. Then I realized, the hub is old and all the cables I was using are the new CAT5s. I dug out an old four-wire with RJ45 connectors that my husband made years ago (probably a cross-over cable). It was quite an effort as the cable is 30 ft. long and wrapped around the perimeter of the office behind desks and file cabinets, entwined with all the other wires. But I plugged it in and, Shazam! I am WORKING!
And, Don, thanks to you, I have eliminated the router from my gaggle of electronic boxes.

Using Airport Extreme Base Station with Cable Modem

Hi everyone,
I have just bought an Airport Extreme Base Station. I connected it to my cable modem (Surfboard 3100) through the WAN port and my iMac G4 is connected to it through the Ethernet port. Installed the Airport Utility, and configured the base station with the normal settings of DHCP for Internet and DHCP for internal network.
After restarting the base station, my Internet connection from the iMac through the base station is very slow and most of the time will time-out. My Internet connection through my PowerBook G4 using wireless through the base station is ok though.
My question is, is there some setting which I should set for the Ethernet portion of the base station to make my wired connections to the Internet work?
Thanks in advance for any help!
regards,
Weiming
iMac G4 Mac OS X (10.4.10)

Hi,
My iMac G4 does not have an Airport card. I did not physically restarted the base station, its part of the sequence when we update the configuration, that the base station will restart on its own.
regards,
Weiming

Using Airport Extreme Base Station As A Wireless Card?

Hi,
I don't know if this is even possible but here's what I'd like to do:
I've started to share an internet connection with a cousin of mine that lives in my apartment building. The connection is in her apartment and as far as I can tell the wireless signal is coming from the modem she has, there is no stand alone router/ base station. So far I've just been connecting using my iBook with the aiport card in it. No problems. I just had to get the ip number and password from her and I was hooked right up.
Here's my real question:
I also have a G4 Mini with no wireless card in it at all and an Airport Extreme base station from before we started sharing a connection. In the time that we've been sharing I haven't connected to the internet at all using the Mini. Now I'm wondering if there is a way I can hook the Airport Extreme to the Mini and somehow use it as a replacement for a wireless card in the Mini. Thus using the Mini connected to the Airport to connect just the Mini to the internet.
I'm not worried about the iBook and do not wish to reconfigure the way I'm using/ connecting with it. Everything is peachy with that.
If this is possible, how can I do it?
Thank you in advance for any help with this.

Ernest Lohrer wrote:
Hi,
I don't know if this is even possible but here's what I'd like to do:
I've started to share an internet connection with a cousin of mine that lives in my apartment building. The connection is in her apartment and as far as I can tell the wireless signal is coming from the modem she has, there is no stand alone router/ base station.
She has an "integrated" modem/router/access point.
So far I've just been connecting using my iBook with the aiport card in it. No problems. I just had to get the ip number and password from her and I was hooked right up.
Here's my real question:
I also have a G4 Mini with no wireless card in it at all and an Airport Extreme base station from before we started sharing a connection. In the time that we've been sharing I haven't connected to the internet at all using the Mini. Now I'm wondering if there is a way I can hook the Airport Extreme to the Mini and somehow use it as a replacement for a wireless card in the Mini. Thus using the Mini connected to the Airport to connect just the Mini to the internet.
I'm not worried about the iBook and do not wish to reconfigure the way I'm using/ connecting with it. Everything is peachy with that.
If this is possible, how can I do it?
Set up the AEBSn as a "bridge" and connect the G4 Mini to one of the "wired" internet connections.

Printing wirelessly using airport extreme base station

I recently set up a wireless network at my house using an airport extreme base station. I plugged my usb printer into the base station and, according to the manual, I can print wirelessly. However, when I go to print, after following the manual instructions, it just times out. Any ideas?

There is already a thread (or two) on the PSC 1410:
Some people have had success here:
http://discussions.apple.com/thread.jspa?messageID=5987003&#5987003

Certain web address not available when using Airport Extreme Base Station

Hello. To access my "secure" account at the local library, I must use a web address that contains a colon followed by a number. I believe that this is a port number, but I confess that all the discussions here regarding ports are going well over my head, and I may be incorrect with this assumption.
My problem is that while I CAN access this site by connecting to my DSL router directly via ethernet cable from my iMac G5, I cannot access the site when connecting to the internet in the mode: iMac Airport to Airport Extreme Base Station to DSL router via ethernet.
The format of the web address is: http://xxxx.yyyy.net:####/zzzzz/, where #### is the number I guess may be specifying a port and causing my problem.
Can anyone advise me, in simple terms, how to get to this address when in the Airport--internet connection mode? Will the solution have any adverse side effects?
Regards and Thanks
iMac G5, 2.5 year old AEBS Mac OS X (10.3.9) Westell 327W 4-port DSL Modem, not using wireless feature.

Very likely the embedded firewall that comes with your AirPort blocks the port you are trying to use.
In order to solve this, best way is to modify the AirPort settings (open the AirPort maintenance app):
Click at the tab "port forwarding" and add the desired port as "public port" to the list. "private IP" is the IP of your Mac and for "private port" type in the port number again.
If you are unsure about the IP of your Mac, look at the network maintenance application.
Well, one side-effect is that you have an open port in your configuration which could cause security issues... but only if you are paranoid So there is nothing to care about (note that without the AirPort inbetween your Mac and your modem, this port would be not blocked and freely accessible

How do I get a VPN acct accessed using Airport Extreme Base station?

I have PC running Windows 2000. For my job, I access a hospital VPN at home. In my home, I am able to set up the Extreme Base Station for wireless conductivity with computers in my home and all have access internet wirelessly. No problem.
The problem is that I cant get it all to work together. How do I configure the base station to recognize/allow the VPN client to enter my network?
I currently have WEP 128 on. The computer used for VPN is hardwired to the base station. Even with security turn-off, I cant access the VPN via base station set up as it is.
help!
PC Windows 2000

I recently got my roommate's Lenovo t43p with VPN to finally work with my Airport Extreme.
1. Open the Airport Utility
2. Double click on your Airport Express on the left side to open up the panel.
3. Click on the "Internet" tab and then select the "DHCP" tab.
4. Click the "+" sign under "DHCP Reservations"
5. Create a name for the profile like "XP Work Laptop" or whatever, and then click Continue
6. You'll need to get your Windows laptop's MAC address which is sometimes under your laptop on a sticker, or you'll have to dig through XP's ridiculous Control Panel to find it.
7. Enter your laptop's MAC address in the field.
8. Lastly, in the 'IPv4 Address" field designate an IP address for your XP laptop that is within your router's range, if you're not sure of the range, the "IPv4 Address" range should be auto-populated with an IP address and you can just try it with that, or if it doesn't work you can change the last number to something higher but no more than like 4-5 digits more.
Hope this helps, Good luck!!

Using AirPort Extreme Base Station to Connect a Hard Drive

I have a wireless network set up using a wireless device provided by my network provider. What I would like to do is to use my Airport Extreme Base station only to connect a hard drive to it. However when doing so, Airport Utility does not recognize or see the Extreme. The Extreme can only been seen if connected to the router provided by my network provider. How can I set up a wireless hard drive or printer with the Extreme without connecting to the network?

Samir, why you wanna use service provider wireless instrument when you have world class wireless device
you don't need 2 wireless ???
I am not expert but I used common sense, I had linksys N series router but recently I bought TC 1TB
so what I dumped my N router in store and went ahead with TC installation, Trust me it took me 10 minutes to configure my 4 HDD 5 computer printer etc with TC
I am sure you have a ethernet modem too separate from your wireless instrument
try to do a clean installation ( thats where all these people who has problem, trying to connect to their existing network
try setting up your AEBS as fresh wireless device connect to your modem and run Airport Utility
I am sure you will be a happy apple customer
good luck

Using AirPort Extreme Base Station as a network AP

I have a Netgear N900 wireless router and and an Airport Extreme Base Station.I used my N900 to create a high speed wirelss network. I would like to use my Extreme Base Station as an access point on this network, in order to get AirPlay and some extra ethernet ports in another part of the house. Is this possible to do, and if so how?
The "extend your current network" option from the Wireless Mode menu does not work. There is no "join your current network" option, like on the Airport Express. What am I missing?
Thank you in advance,
Alex

The Extreme *does not* let you joint an existing network
Yes it does. Please open up AirPort Utility 5.6, select the Extreme and click Manual Setup
Click the Wireless tab below the row of icons
Hold down the option key on your Mac while you click on the Wireless Mode selection box.
What happens? Now you see the "Join" selection.
Problem is, only the USB port is enabled if you configure the Extreme to "join".......as I already stated. The Ethernet ports are not enabled.
The AirPort Express 802.11n has a special feature that allows it to "join a wireless network" and the Ethernet port can be enabled.
The AirPort Extreme does not have this feature.....which might be the reason why Apple hides the "Join" setting for the Extreme.

Using airport extreme base station modem to fax

Can I use an Airport Extreme Base Station with a modem to send faxes?
powerbook G5 Mac OS X (10.4.8)

kersto, Welcome to the discussion area!
No. The built-in 56k modem is only for connecting to a dial-up ISP. There is no ability to send FAXes.

Airport Extreme base station vs. Linksys router

Hi all -- I have a tech choice to make and I'm soliciting advice and war stories from those who have been in my place.
I have a DSL connection, G5 Mac and a Windows laptop. I've been connecting to the Internet via a Linksys WRT54G router -- the Mac is connected to the router via Ethernet, and the Windows machine connects wirelessly -- and I've been happy with this setup. I have it on good authority that I'll be getting an Airport Express in my stocking this year; I had done a little research and found that it is possible to make the WRT54G and the Airport Express work together, and was planning on doing some hacking and fiddling to make that happen in the new year.
However, last night my WRT54G seems to have died a horrible death -- all its lights started blinking at once, the Internet connection went away, then all the lights went out except for the "diagnostic" light, and now no lights come on at all. No idea what happened, but it seems pretty kaput.
So! I'm in need of a new wireless base station. I could get an Airport Extreme base station, or I could get another Linksys (or another off-the-shelf 802.11 router, but we'll just use "Linksys" as the catch-all phrase here to mean "not an Airport Extreme base station"). The most obvious difference is price -- the Airport Extreme station is $200, while the Linksys is more like $65. Another thing that irks me about the AE station is that it only has one LAN port. I do like being able to plug in my laptop to the wired network to do some diagnostics once in a while and it'd be a pain to have to disconnect my Mac to do so. And then there's nagging worries that the AE base station might not work as well with my Windows laptop.
On the other hand, I'm sure that setting up the Airport Express would be much, much easier with the AE base station. And I do like the idea of the base station being able to dial up if my DSL goes down (as it does from time to time). Basically, I am tempted by the AE base station feature-wise, but I'm kind of balking at paying three times the price and not getting even a second LAN port. Any advice, particularly from people who have used both types of routers in a mixed network, would be appreciated.

Replace your Linksys with another WRT54G. Then you can hook up your anticipated AX as either a client (connected like a computer), a wireless access point (connected using ethernet with DHCP disabled on the AX), or using WDS:
http://discussions.apple.com/click.jspa?searchID=-1&messageID=607414

I have an Apple AirPort Extreme Base Station (Simultanious Dual_Band) (MC340LL/A), and updated the software. After updating no devices can connect via wifi. Any suggestions.

I have an Appl,e AirPort Extreme Base Station (Simultaneous Dual_Band( MC340LL/A. After updating the software, no devices can connect via wifi.

As suggested in another discussion area, (AirPort), I reset the AEBS to factory defaults. On the TV, I went to >Settings>General>Network>Configure Wireless>Wireless Networks. I could then see the generic "Apple Network xxxxx" on the TV. From my MacBookPro, I verified that I could connect to the TV by launching iTunes and noting that the TV was now visible in the "Devices" menu. Went back to the AEBS and ran through the "Setup" routine. I did NOT use the "Previous Settings" but instead, saved the old settings profile, created a new wireless network and new settings profile and enabled WPA2 Personal encryption. I then went back to the TV and went through the "Settings" routine again (as noted above). This time, after entering my WPA2 password, the TV connected to the network and problem was solved. Thanks.

Apple airport extreme base station b/g (old model) and airport express

i want to extend the range of my old airport extreme base station, the one that is a circular pyramid. I was wondering if the airport express would work or if I should get something else.

Hello lvpd. Welcome to the Apple Discussion!
i want to extend the range of my old airport extreme base station, the one that is a circular pyramid. I was wondering if the airport express would work or if I should get something else.
Yes, you can extend the older 802.11b/g AirPort Extreme Base Station (AEBS) with the newer 802.11n AirPort Express Base Station (AXn). To do so, they would both need to be reconfigured for a Wireless Distribution System (WDS).

Airport Extreme Base Station as Wireless Adapter

I have a Verizon FIOS network coming into my house and connected to the supplied wireless router. Our three Macs are connected to it wirelessly, as our the iPhone and Touch.
I have a G5 in the basement that does not have a wireless adapter. I bought an older AEBS b/g model in hopes that I could connect to the G5 (with the LAN port) and wirelessly connect to my existing home network. Basically, I was hoping to use it as a wireless adapter.
Is this possible? I have been looking all over as well as in the documentation and cannot figure out how to do it.
Thanks for the help.
Jeff

I bought an older AEBS b/g model in hopes that I could connect to the G5 (with the LAN port) and wirelessly connect to my existing home network. Basically, I was hoping to use it as a wireless adapter.
Is this possible? I have been looking all over as well as in the documentation and cannot figure out how to do it.
Sorry, but no. Instead, the newer 802.11n AirPort Express Base Station (AX) could be used as an Ethernet bridge, which would basically do the same thing. With this type of bridge, you could connect your G5, by Ethernet, to the AX's Ethernet port and, in turn, the AX would connect wirelessly to your Verizon wireless network.

Can't create a working Wireless Network using Airport Extreme Base Station

I don't know what I'm doing wrong...
I've got the cable from the modem going to the base station. I follow ALL on screen instructions. I select "Using DHCP" because when I plug the ethernet cable into my MBP it automatically does everything for me, and has that as its setting as well.
I get to the stage where it asks whether or not I'd like it to share an IP or go into bridge mode, I'm not sure what either of these two mean...I've tried both and both result in no wireless internet.
On several occasions I get to the end, and after I do the "final" update is comes back with one problem - internet connection, saying the router doesn't have a valid IP.
I'm totally lost on what to do here...
If you need more information just ask...please...

The below procedure is described in your AirPort setup manual, but it can be a little confusing. Here is my step-by-step procedure for an AEB setup for the system you describe:
A. Setup the 'Main' Base Station:
1. Do a factory reset of your AEB (main), then turnoff the DSL Modem and the AEB (main).
2. Check ethernet cable connections:
- DSL Modem > AEB (main) WAN port;
- AEB (main) > Mac computer running OS X 10.5.x.
3. Power-on DSL Modem and wait for it to initialise.
4. Power-on the AEB (main) and start your Mac computer.
5. Open AirPort Utility and select the AEB (main) in the LH pane. Click 'Continue' and give the AEB (main) a name and an admin password (twice). Click 'Continue'.
6. Select 'I don't have a wireless network and I want to create one', click Continue.
7. Give your network a name, select WPA/WPA2 Personal and insert the wireless network password (twice) - use 13 alpha/numeric characters for password. Tick 'Remember this password in my keychain'. Click 'Continue'.
8. Select 'I connect to the Internet with a DSL or cable modem using DHCP. Click 'Continue'.
9. Click 'Update' and wait for the AEB (main) to restart.
10. Disconnect the ethernet cable between your Mac and the AEB (main).
B. Setup Client computer
1. Open System Preferences/Network/AirPort.
2. Against 'Network Name:' select your network (the name you gave it at A7).
3. Click 'Advanced' and select TCP/IP. Against 'Configure IPv4:' select 'Using DHCP', then click 'OK'.
4. Click 'Apply' and exit System Preferences.

Using Airport Extreme base station as wireless Cable router and airtunes.

Similar Messages

Maybe you are looking for