Using iPod shuffle 4th generation for first time and receiving the error : one of the USB devices attached to this computer has malfunctioned, and windows does not recognize it. For assistance in solving this problem, click this message

Using iPod shuffle 4th generation for first time and receiving the error : one of the USB devices attached to this computer has malfunctioned, and windows does not recognize it. For assistance in solving this problem, click this message.
Using win 7 and latest iTunes [10.6.3]. Have already gone through below links and did not find any solution.
http://support.apple.com/kb/HT2292
http://support.apple.com/kb/TS1369
http://support.apple.com/kb/HT1923
http://en.kioskea.net/forum/affich-17997-ipod-not-detected

I was hoping it would be something like a USB device conflict, but now the shuffle is the only thing connected...
This article was one of the ones you linked to above in your initial post
http://support.apple.com/kb/TS1369
Under Part 9. Verify that USB drivers are installed, did you try the steps in If only "Unknown Device" appears? That appears to be your situation.
Also, you said that the shuffle initially worked well enough to do a sync, then it had the same problem again. If you can get it to work again initially, before doing anything else, try the following. Select the shuffle in the iTunes sidebar, under DEVICES. Over to the right, go to the Summary tab. By default, the checkbox for Enable disk use should be unchecked. If so, check it and Apply the change. See if that makes any difference.
(If Enable disk use was already checked, try unchecking it and Apply the change. Basically, set it the "other way" and see if there is any improvement.)
NOTE: When disk use is enabled, you have to eject the iPod in iTunes before disconnecting it physically.
If the disk use change makes a difference, that may provide a clue about the actual cause.

Similar Messages

My computer will not recognize my iPod Nano when i connect it. I tried my laptop instead but it said the same thing - one of the USB devices attached to your computer has malfunctioned, and windows does not recognize it. Can i fix this?

My 16 gig iPod Nano 7th gen was put of power. I connected it to the computer and it started to turn on (the apple appeared in the middle of the screen). Then left it two minutes and the computer went into sleep mode. My iPod nano had gone off and now it will not turn on, or connect to the computer, so i cannot charge it. I am not sure if it is a problem with the usb cable. When I conntct the cable to the computer nothing happens, but then when i connect the iPod to the cable it says 'one of the USB devices attached to your computer has malfunctioned, and windows does not recognize it'. Please don't say its broken already

It probably needs to be reset. The procedure is different for different Nano models: http://www.apple.com/support/ipodnano/assistant/itunes/

Cant Charge/connect ipod touch. Get an error saying "One of the USB devices attached to your computer has malfunctioned, and Windows does not recognize it" . HELP.

Ok . so my ipod touch 2G , used to be all ok . its just yesterday i went to charge my ipod it wouldnt do anything . Then after being plugged in for a bit , i got pop up saying " "One of the USB devices attached to your computer has malfunctioned, and Windows does not recognize it" .
Ive tried plugging this into 3 other computers same error message pops up .
PLEASE help me . thanks (:

Uninstall your USB drivers in your computer & reinstall.
contact your pc manufacturer for the steps.
Although I am working on behalf of HP, I am speaking for myself and not for HP.
Love Kudos! If you feel my post has helped you please click the White Kudos! Star just below my name : )
If you feel my answer has fixed your problem please click 'Mark As Solution' and make it easier for others to find help quickly : )
Happy Troubleshooting : )

One of the usb devices attached to this computer has malfunctioned, and Windows does not recognize it. For assistance in solving this problem, click this message.

I connected my sons Ipod Touch to my pc and it worked fine. Now, when I try to connect my iPad the following message comes up: One of the usb devices attached to this computer has malfunctioned, and Windows does not recognize it. For assistance in solving this problem, click this message.
I checked the cable. It surely is not the cable. If I connect the iPod again it works fine. If I use the same cable with my pc and ipad at work or my other son’s laptop, it is working perfectly. It is only on my laptop where the iPod was connected. Something tells me it got something to do with the drivers that went corrupt or something when I connected the iPod.
I searched the internet and I see a lot of people gets this message. Still no solved answers yet. Is there a place where I can download the drivers again or any other suggestions?
Windows 7 and iPad 2
Kind regards,

I was hoping it would be something like a USB device conflict, but now the shuffle is the only thing connected...
This article was one of the ones you linked to above in your initial post
http://support.apple.com/kb/TS1369
Under Part 9. Verify that USB drivers are installed, did you try the steps in If only "Unknown Device" appears? That appears to be your situation.
Also, you said that the shuffle initially worked well enough to do a sync, then it had the same problem again. If you can get it to work again initially, before doing anything else, try the following. Select the shuffle in the iTunes sidebar, under DEVICES. Over to the right, go to the Summary tab. By default, the checkbox for Enable disk use should be unchecked. If so, check it and Apply the change. See if that makes any difference.
(If Enable disk use was already checked, try unchecking it and Apply the change. Basically, set it the "other way" and see if there is any improvement.)
NOTE: When disk use is enabled, you have to eject the iPod in iTunes before disconnecting it physically.
If the disk use change makes a difference, that may provide a clue about the actual cause.

Error code 43 with message 'one of the USB device attached to this computer has malfunctioned, and Windows does not recognise it'.

i have suddenly got this message 'one of the USB device attached to this computer has malfunctioned, and Windows does not recognise it'. it says error code 43. the usb drives (2 in no.) have stopped working as in they dont recognise the external hard drive
or pen drive. I have a HP pavilion dv4 series notebook. the usb drives were working fine - however suddenly yesterday this strange message cropped up. life has taken a drastic turn! please help.
in device status is says: Windows has stopped this device because it has reported problems. (Code 43)
location: Port_#0002.Hub_#0005
driver provider: microsoft
date of driver: 21-06-2006
driver version: 6.1.7600.16385
HELP!!!!!!!!!!!

Hi ameet2005,
Please check if the following suggestions help:
First, please disconnect all USB devices and then perform the following steps:
1. Click "Start" button, type “devmgmt.msc” (without quotation marks) in the “Search” bar and press "Enter". Click “Continue”
if necessary.
2. In Device Manager, double click to expand "Universal Serial Bus controllers", right click on the Host Controller, click "Uninstall" and click "OK".
3. Repeat the step 2 to uninstall all items under "Universal Serial Bus controllers".
Then, restart your computer and Windows 7 will reinstall all USB controllers automatically.
If the issue persists, please check if it can be resolved by running
System File Checker.
Please remember to click “Mark as Answer” on the post that helps you, and to click “Unmark as Answer” if a marked post does not actually answer your question. This can be beneficial to other community members reading the thread. ”

G31TM-P21 One of the usb devices attached to this computer has malfunctioned and

Just bought the G31TM-P21 motherboard and installed it with a E3200 proc. Whenever I plug in a USB device in one of the four ports on the back panel I get the message:
"One of the usb devices attached to this computer has malfunctioned and windows does not recognize it. For assistance in solving this problem, click this message."
After clicking the message I get a window with:
"One of the usb devices attached to this computer has malfunctioned and windows does not recognize it." with a tree of USB Root Hub (2 ports) with Unused Port and Unknown device under it.
If I go to Device Manager nothing appears to be uninstalled but if I expand the USB I do have a single instance of Unknown Device among the root hub and host controller. I'm running windows XP home 32 SP3.

Quote from: Wonkanoby on 14-November-09, 18:21:00
what device
what is usb in your set up
Any device, keyboard, mouse, printer, etc.

Iphone 3gs is not charging nor detected by i tunes and computer shows 'One of the USB devices attached to this computer has malfunctioned and windows does not recognize it'

Hello evi one .. My iphone 3gs is not charging and is not recognised by itunes .whenever i attach my iphone to my computer,it displays a message 'one of the USB devices attached to this computer has malfunctioned and windows does not recognize it ' . :-( it do charging sometime with charger but does'nt by computer . kindly please tell me the solution .. thanks

As I said above, some of the new lightning cables have been known to be causing problems for some users. Have it replaced if at all possible by bringing it into your local Apple Store's Genius Bar.
B-rock

When i attach my iphone 4 with computer it shows one of the USB devices attached to this computer has malfunctioned and windows does not recognize it,now what can i do ..plz help me

when i attach my iphone 4 with computer it shows one of the USB devices attached to this computer has malfunctioned and windows does not recognize it,now what can i do ..plz help me

I would first try unplugging All the USB devices plugged into your computer, and then plug back in just the iPhone and see if that is recognized. Also, do you have the latest version of iTunes for Windows installed on your PC, as you need to?
Hope this helps

Computer says 'one of the USB devices attached to this computer has malfunctioned and windows does not recognize it'. what do i do?

i have an ipod nano 7th gen and when i plug it in for itunes my computer says 'one of the USB devices attached to this computer has malfunctioned and windows does not recognize it'. what do i do?

As I said above, some of the new lightning cables have been known to be causing problems for some users. Have it replaced if at all possible by bringing it into your local Apple Store's Genius Bar.
B-rock

My computer will not recognize my ipod touch anymore. When I plug it in it says the USB device attached to this computer has malfunctioned and windows doesn not recognize it.

My computer (PC) will not recognize my ipod touch anymore. When I plug it in, it says the USB device attached to this computer has malfunctioned and windows does not recognize it. I have tried attaching the same cord and ipod to a different computer and it is recognized by our mac. I have tried restarting the ipod, downloading all updates on my pc, restarting the pc, etc. Nothing has worked. Please advise.

See:
iOS: Device not recognized in iTunes for Windows
I would start with
Removing and reinstalling iTunes, QuickTime, and other software components for Windows Vista or Windows 7

Hi my ipod was working perfectly fine but i turned it on the net day and i was stuck in recovery mode ans my computer keeps on saying one of the usb devies attached to this computer has malfunctioned and window dose not recognize

hi my ipod was working perfectly fine but i turned it on the net day and i was stuck in recovery mode ans my computer keeps on saying one of the usb devies attached to this computer has malfunctioned and window dose not recognize

https://discussions.apple.com/message/23791369#23791369
https://discussions.apple.com/thread/5325044?tstart=0
more
https://www.google.dk/search?q=restore+iphone+error+29&oq=restore+iphone+error+2 9&aqs=chrome..69i57j0l5.4603j0j7&sourceid=chrome&espv=210&es_sm=93&ie=UTF-8

One of the USB devices attached to this computer has malfunctioned and ...

Hello all, I have the same problem with one of our members here and also would really appreciate some help. I have a iPod video since last December and it worked just fine. Yesterday, I took some of the data out from my iPod with another computer and everything ran fine also. But when I connected my iPod to my laptop, it said "USB devices attached to this computer has malfunctionedand Windows does not recognize it". I tried to connect that to another computer and same message popped out. I have charged my iPod, it usually took few hours to recharge the battery but this time, even though it was charged for more than 6 hours, it is still not fully charged. The iPod works fine (it plays all of my current uploads on it) it's just that it won't communicate with my computer so I can't update content and get my data out of my iPod.
I have tried to updates iPod in a disk mode, connect and reconnect again but it still doesn't work. I very much appreciate it if anyone can help. I can't afford to lose the data I have in my iPod. Thanks.

I'm not really up on the complexities of the Windows OS but try this tip I picked up a while back, hopefully it might help.
"USB Device not Recognized in Windows"
1. On the Start menu, click Control Panel.
2. Double-click the System icon.
3. Click the Hardware tab.
4. Click Device Manager.
5. Scroll down the list of devices to the Universal Serial Bus controllers
6. Click the plus icon next to the Universal Serial Bus controllers.
7. Double-click one of the indented USB Root Hub entries.
8. Click the Power Management tab.
9. Deselect the "Allow the computer to turn off this device to save power" option.
10. Click the OK button at the bottom of the window.
11. Restart the computer.

Windows does not recognize driver for pci-4461

Hello,I am currently running windows xp with labview 7.0 on my computer. Recently trying purchased and trying to install PCI-4461 Audio Analyzer PC card. I downloaded the latest driver 9.0.2 off the NI website. After the install I verified the driver exist by using the Measurement & Automation tool. However, window does not recognize any driver for the hardware. When I point it to the directory where the driver is "suppose" to exist, windows gives me an error message saying that the driver does not exist or is corrupted. I've tried uninstalling and reinstalling several times. Has anyone ran into this problem and can give me some advise? I know that the version on DAQmx 9.0.2 is not compatible with the version of labView I am running. However it should not affect windows from locating and installing hardware. Thank you,Ruth

Hi Ruth,
Did you install the PCI-4461 card in your computer before or after you installed the DAQmx 9.0.2 drivers? It would be best to install the drivers first and then the card. Windows XP will pop up the New Hardware Wizard, saying it detected new hardware. Click Next, and then to Search for Drivers Automatically. Do not try to navigate and select the appropriate driver folder. As long as the drivers are installed correctly Windows will be able to find the correct driver automatically.
You can also remove the PCI-4461 card and try it in a different PCI slot. This will cause the new hardware wizzard to appear on the next restart.
Eric S.
Eric S.
AE Specialist | Global Support
National Instruments

Okay every time i plug my ipod up to my laptop a message comes up and says one of the USB devices attached to this computer has malfunctioned, and Windows does not recognize it. Can someone plz help me ive done everything.

I really need assistance/help with my ipod because it was working fine one day. Then the next day i decide to put more music on it then this message came up, and ive tried all the troubleshooting stuff and different links to help but still no success. But theres one thing i havent tried yet someone told me to buy another Apple charger and wall plug in to see if that works other than that i need help because i went to settings and erased everything off my ipod to see if that worked and it didnt so all my stuff is gone....Yeah i was ****** but plz help me!

I would first try unplugging All the USB devices plugged into your computer, and then plug back in just the iPhone and see if that is recognized. Also, do you have the latest version of iTunes for Windows installed on your PC, as you need to?
Hope this helps

Cannot sync iTouch. {"One of the USB devices attached to this computer has malfunctioned, and Windows does not recognize it."}

Any help? I have not synced the iTouch in quite a while because it could not be found after an out-of-state move. I just found it, after two years, and am wondering if it will sync if I Restore it. I don't want to lose all of my music and if there's a way to avoid that, I would appreciate it the recommendation.
jvb654

Hello jvb654,
Thanks for using Apple Support Communities.
For more information on this, take a look at:
iOS: Device not recognized in iTunes for Windows
http://support.apple.com/kb/TS1538
Follow these steps, testing to see if the issue is resolved after each section.
Best of luck,
Mario

Using iPod shuffle 4th generation for first time and receiving the error : one of the USB devices attached to this computer has malfunctioned, and windows does not recognize it. For assistance in solving this problem, click this message

Similar Messages

Maybe you are looking for