VD offline;still the Volume is accessible in read-only mode.

Hi,
In our lab, we have a test server setup with Windows 2012 R2(Build 9600) Standard edition installed.
As part of our test exercise, we need to induce the failure of a RAID 0 drive(internal storage) and carry out the volume/applications recovery.
We induced the drive failure by pulling out a disk drive from a RAID 0 volume. As soon as the drive was pulled out, the LSI storage controller reported the VD offline. The windows disk management did show the uninitialzed/unallocated drive
on rescanning drives.
But the specific volume is still accessible from Windows explorer in read only mode. The applications(sql server database) that are running on the specific volume are also running fine (they are of read-only nature).
We are quite surprised by this behavior. Please advise.
Thanks and Regards,
Jisha

have you attempted a reboot? Pulling a drive may have different behavior than a failed drive.
LSI is a raid controller but if you see both drives it sounds like you may be using a software raid?

Similar Messages

It is possible to apply redo while the standby is open in read only mode ?

Hi,
I am using Oracle 11g R2 (11.2.0.1.0)
Step 1: Two node RAC is Configured.
Step 2: One node Data Guard RAC is configured.( i,e Standby is one node RAC).
Primary:
SQL> select open_mode,database_role,PROTECTION_MODE,PROTECTION_LEVEL from v$database;
OPEN_MODE DATABASE_ROLE PROTECTION_MODE PROTECTION_LEVEL
READ WRITE PRIMARY MAXIMUM AVAILABILITY MAXIMUM AVAILABILITY
Standby:
SQL> select open_mode,database_role,PROTECTION_MODE,PROTECTION_LEVEL from v$database;
OPEN_MODE DATABASE_ROLE PROTECTION_MODE PROTECTION_LEVEL
READ ONLY WITH APPLY PHYSICAL STANDBY MAXIMUM AVAILABILITY MAXIMUM AVAILABILITY
Question:
I have not purchased active dataguard license.
In my case In Data Guard RAC it is possible to apply redo while the database is open in read only mode?
Thanks
Solaiman

876149 wrote:
SQL> select open_mode,database_role,PROTECTION_MODE,PROTECTION_LEVEL from v$database;
OPEN_MODE DATABASE_ROLE PROTECTION_MODE PROTECTION_LEVEL
READ ONLY WITH APPLY PHYSICAL STANDBY MAXIMUM AVAILABILITY MAXIMUM AVAILABILITY
"READ ONLY WITH APPLY" in V$DATABASE.OPEN_MODE means Active Data Guard is enabled.
Oracle code cannot check if you have the right license: it is up to you to know which license you have for your database environments.

Write-protect mode is currently active. The editor is now in read-only mode

How do i get the portal out of write protect mode.   No matter what i change to do, i get the message
Write-protect mode is currently active. The editor is now in read-only mode.
this shows up in the log
10/06/10 16:21:21 - ERROR: Not deployed. Deploy Service returned ERROR:
                     java.rmi.RemoteException: Cannot deploy application sap.com/com.sap.pct.bi.tct.BI_Administration..
                     Reason: <--Localization failed: ResourceBundle='com.sap.engine.services.deploy.DeployResourceBundle', ID='Exception during
deploy: Import aborted - write protect mode is active.

Hi David,
Do the following steps:
       1.       Start the Visual Administrator .
       2.       Choose Global Configuration   u2192Server u2192Services u2192com.sap.portal.pcd.gl .
The properties of the service are displayed:
                            a.      Pcd.Pl.WriteProtectActivated defines whether or not write-protect mode is activated. By default it is set to false .
                            b.      Pcd.Pl.WriteProtectCause describes the reason that write-protect mode is activated. This information appears in the log files.
       3.       Deactivate write-protect mode by entering false as the value for Pcd.Pl.WriteProtectActivated .
       4.      C lick Update and then click Save .
A confirmation dialog box opens.
       5.       To apply the changes to all cluster elements, click Yes .
       6.       To reset the default values, click the Reset Default Global Properties icon .
This will deactivate the write protect mode.
Thanks and Regards,
Syam.

The Index Server is in Read Only Mode

Hi,
In our test environment ALL of our jobs are failing. The message in every failed Job Log is:
11/18/05 10:25:15- Starting to run operations (1 total) for job 'Search Update 2 - Run Once'. Will stop on errors. (PID=14064)11/18/05 10:25:16- *** Job Operation #1 of 1: System Agent 'Search Update Agent' [Run as owner 'Administrator']11/18/05 10:25:16- The index server is in read-only mode.11/18/05 10:25:16- The index Server is inaccessible. Search Update cannot continue and will terminate.11/18/05 10:25:16- *** Job Operation #1 failed: Call to perform operation #1 failed with error (0x80044301): (null) (0x4)11/18/05 10:25:16- Call to perform operation #1 failed with error (0x80044301): (null)
has anybody seen this before, and how can I correct it?
Thanks,Shawn

The search server goes into read only mode in response to certain error conditions. Simply restart the service to put the search server back into R/W mode. The server will attempt to self repair on startup. You should review your recent search server logs to see if there are errors that may have caused the transition to read only mode. If problems persist, contact tech support for further assistance in troubleshooting.

The MDM repository is in read-only mode

Hi Experts,
In our environment we have a Master ans Slave repository and the synchronization is being scheduled daily.
Now we understand from the MDIS logs of the Master repository that the repository is in Read-Only mode and none of the records can be updated / created.
We have tried restarting the repository too.
Please advice.
Thanks,
Sridhar T A

Chander,
We get Check/Verify Option only after repository is unarchived/created. So, this can not be applied in Maria's case....
Maria,
Please let us know what version of MDM you are using.. Are you sharing database for MDM with other systems too??
Also, can you check MDM logs and provide detailed error message from logs...You can check MDM server logs either from Console or On MDM server log directory...
This information will help..
Please also try this after setting following entry in MDS.INI file:
Unarchive Ignore Language Count=True
Best Regards,
Shiv

Convert the oracle10g database into standby ( read only mode)

One month ago, converted the oracle 10g standby database into read and write mode( database is open). I would like to convert the oracle10g database into standby
Please provide me the steps or document
Thanks in advance

user8680248 wrote:
two months ago we have convert the standyby database into standard database ( read, write)
NoW I am plannning to convert this database into standby database
any link or steps pleaseDid you meant you would creating(or you have) another standby database and make that standby database as primary and this as standby
If this is not what you meant then there is no way you can make this as sandby database.
Regards
Anurag

Volume works only in read only mode

Our Xsan volume is going nasty
if any client tries to write on it , the xsan would crash and disconnect on all clients
only way to bring it back is to shutdown all machines and power on again
it works fine when the volume is mounted as read only though , so now I have a volume I can only read from , but can't write to
any one had this happening before ? any idea what might be causing it ?
Thanks

Our Xsan volume is going nasty
if any client tries to write on it , the xsan would
crash and disconnect on all clients
only way to bring it back is to shutdown all machines
and power on again
it works fine when the volume is mounted as read only
though , so now I have a volume I can only read from
, but can't write to
any one had this happening before ? any idea what
might be causing it ?
Thanks
Here is what I would suggest:
Check the time stamp on all your machines
Xsan versions (are they compatible)
OS revision
Private Network connectivity

How to display the "display values" in READ Only mode for a SHUTTLE

Hi,
I have a form item of type *'Shuttle'* and using the following LOV.
   select DEPTNAME d, DEPTNO r
    from DEPTIn normal mode..it displays the department name and internally store the Deptno..
Now I converted this item to Read Only mode using Read Only Condition Type
the problem is as soon as it becomes read only...it displays the deptno....not the department name
            Department-   10:20:30How can I display the "display values" i.e the actual department name in read only mode..
            Department-   Department1:Department2:Department3Thanks,
Deepak

Hi,
It seems feature. Shuttle is span tag when it is read only.
Work around could be that
you compute display as text item with LOV display value according shuttle session state and show shuttle and this item conditionally depend case
Br, JAri

Which table shows the tablespace in read-only mode or read-write mode.

HI All,
Can someonoe help me out to find which table shows whether the a tablespace is in Read-only mode or Read-write.
Thanks,
naveen

Try this:
select tbl.table_name, tb.tablespace_name, TB.STATUS from dba_tablespaces tb, dba_tables tbl
where TB.TABLESPACE_NAME = tbl.TABLESPACE_NAME and TB.TABLESPACE_NAME = 'YOUR_TABLESPACE_NAME' and tbl.table_name = 'TABLE_NAME'

Essbase Java API - Check if the cube is in read-only mode

Hello,
I use "Essbase Java Api 11.1.2.0" to manage my essbase server.
I made a script based on sample to make a cube in read-only mode and I have an exception when the cube is already in read-only mode.
So is-it possible to check if the cube is in read-only mode with the essbase java api ?
Thanks
Arnaud

Hi,
I have a solution that might work for you, please follow steps below:
1) Go to your project schedule, make a small modification to any task on schedule and 'Publish' the project.
2) While your project is being published and saved, open another window
Server Settings -> Manage Queue Jobs
3) Here you can view the progress of your current Project Publishing update, check if all goes smooth and your project is published successfully without indicating any errors :
( to view any error look at the last column of
table on Manage Queue Job page)
4) Also in your Project window see if the project is published and not saved as Draft.
Basically this will give you a fair idea of your project being published or not.
Regards

Opening the file in read only mode

hi all,
i am using
i want to open any type of files in read only mode using host command.so first i am setting the attribute to read only and then opening the file. But still the opened file is editable. i have written like below
Host( 'cmd /c attrib +r "\test_folder\testing\PURCHASE_ORDER\'||:PO_FILE_NAME||'"',NO_SCREEN);
Host( 'cmd /c "\test_folder\testing\PURCHASE_ORDER\'||:PO_FILE_NAME||'"',NO_SCREEN);is this is the way to open the file in readonly mode?
Along with the above the files which i opened with the help of above said code those files i am not able to delete also.(i have to delete the selected file)
i thing when i am setting the attribute something is going for a mess!
Please help.
Thanks..
Edited by: GD on Jun 23, 2011 2:25 AM

hi,
Read only means you cannot mofiy the file. This also includes that you cannot delete a readonly-file yes,
what i am doing is i have three button in my layout 'save','view' and 'delete'.
1.so when user press 'save' button after selecting the file then the file gets saved into the specified.
2. when user press 'view' button the file has to open in read only mode.
for this i have written above mentioned code(but still i am able to edit the file)
3.when user press 'delete' button the file has to be deleted from the specified location.
so my problem is after setting file to read only mode, i am able to edit but i am not able to delete it.
What i am using to set the file to read only mode is right?
Please help.
Thanks..

Datafile offline in reade only mode

i read the oracle9i reference and it show me the message
'Read-only mode does not restrict database recovery or operations that change the
database’s state without generating redo data. For example, in read-only mode:
Datafiles can be taken offline and online
Offline datafiles and tablespaces can be recovered
The control file remains available for updates about the state of the database'
first one the message show me is 'datafiles can be taken offline and online' , i think this tell me i can change the datafiles's state online to offline, so when i use
alter database datafile test.ora offline is a error ora-01145 in the noarchivelog mode
but it is successful in the archivelog mode
so could anyone tell the distinct of two mode the database and tablespace offline

The docs are at http://tahiti.oracle.com.
No doubt while reading the docs you will find other valuable information that someone writing you a short paragraph would omit.

The report parameter 'param1' is read-only and cannot be modified. (rsReadOnlyReportParameter)

hey guys..
I'm trying to get the report that I need to be filtered by a parameter value (named Param1)
I created a parameter in the data tab and tried to pass a value from my Web application to the report services.. now my report have that textbox that prompts me to enter the filtering value for the report I want.. everything works fine till this point..
now I have another webpage that has a report viewer and a textbox for the user input the value they want.. and pass it to the report.. and I'm using the following code to pass the value to the report I made earlier..
Dim par(0) As Microsoft.Reporting.WebForms.ReportParameter
par(0) = New Microsoft.Reporting.WebForms.ReportParameter("paramSiteCode", TextBox1.Text.ToString)
ReportViewer1.ServerReport.SetParameters(par)
ReportViewer1.ServerReport.Refresh()
however.. now I'm getting an error.. "The report parameter 'paramSiteCode' is read-only and cannot be modified. (rsReadOnlyReportParameter)"
what am I missing here? I've been thru the help and forums.. and the code should work.. or so I hope it would.. thanks in advance..

Details
Product:
sql server reporting services
ID:
rsreadonlyreportparameter
Source:
microsoft.reportingservices.diagnostics.utilities.errorstrings.resources.strings
Version:
8.00
Message:
The report parameter '{0}' is read-only and cannot be modified.
Explanation
This error occurs when you attempt to set a value for a parameter that is read-only. A parameter is read-only when the
Prompt property for the parameter is set to false.
User Action
To set a value for a parameter, the Prompt property for the parameter must be set to
true. You can set this property in two ways:
Before publishing the report, provide a prompt string for the parameter. In Report Designer, you can provide a prompt by typing a prompt string in the
Prompt text box in the Report Parameters dialog box.
After publishing the report, set the Prompt User property for the parameter. In Report Manager, in report properties, click the
Parameters tab, and then select Prompt User for the parameter.
For more information about report parameters in Report Designer and Report Manager, see Books Online.
In the release version of SQL Server 2000 Reporting Services, when Prompt is
true and Prompt String is blank, the parameter is still available to the user in the report viewer. In SP1, when
Prompt is true and Prompt String is blank, the parameter is hidden from the user.
Note: Publishing a report over an existing report on the report server does not overwrite the parameter information. To update parameters for an existing report, either delete the report on the report server and republish, or update the parameter information
for the report in Report Manager.
I struggled with the same problem in VS 2010.
After a long series of hoops to jump through, I modified the rdlc file by hand and added <Prompt>true</prompt>. This parameter cannot be set through the GUI - go figure.
In my case, I was attempting to generate a sub report, and pass a parameter to the sub report.
To get this to work, the sub report needed these two sections.
<ReportParameters>
<ReportParameter Name="Network_Id">
<DataType>String</DataType>
<Prompt>true</Prompt>
</ReportParameter>
</ReportParameters>
<Variables>
<Variable Name="Network_ID">
<Value />
</Variable>
</Variables>
I was then able to use the name "Network_Id" in the sub-report properties of the "sub report control" for the name of a parameter on the parameters tab. I then set it to the key value that I need in the subreport properties dialog.
Prior to setting prompt to true, I kept getting the read-only exception.
I'm not sure if I am being clear about this, but sub reports do work, and prompt can be manually added to the report definition file.

I am not able to use Firefox with Sharepoint - I can only open a file in read-only mode and cannot checkout the document and edit.

I would like to use Firefox with Sharepoint.
However, I am only able to open a file in "read only" mode whch means I cannot edit the document and save it. I am also not able to "check-out" a document in Sharepoint and edit it at the same time.

This may not work for everyone, but I solved this problem by clicking on the file name in sharepoint, not the document icon to the left of the name. This then brought up the various options, including checking out, editing, version history etc. It seems obvious but I have only just realised this!

The project cannot be checked out because the server is in read-only mode.

Receiving the message "The project cannot be checked out because the server is in read-only mode." when a project manager is trying to access a project. He is a backup PM, and I'm wondering if that's why he is getting the message (since he is
not the Owner or Status Manager of the project he is trying to access). We are using SharePoint permissions in Project Server 2013.

Hi,
I have a solution that might work for you, please follow steps below:
1) Go to your project schedule, make a small modification to any task on schedule and 'Publish' the project.
2) While your project is being published and saved, open another window
Server Settings -> Manage Queue Jobs
3) Here you can view the progress of your current Project Publishing update, check if all goes smooth and your project is published successfully without indicating any errors :
( to view any error look at the last column of
table on Manage Queue Job page)
4) Also in your Project window see if the project is published and not saved as Draft.
Basically this will give you a fair idea of your project being published or not.
Regards

VD offline;still the Volume is accessible in read-only mode.

Similar Messages

Maybe you are looking for