Vista/Windows 7 Duplex Patch for Officejet 7210 7310 7410 and Photosmart 2610 2710

Some printer model with automatic duplexers do not properly print the back page in Vista (or in Windows 7 if updated from Vista). In these models the back side is printed updside down regardless of the driver settings.
The attached zip file has a patch and instructions to correct this issue for the following printers:
Officejet 7210
Officejet 7310
Officejet 7410
Officejet L7300
Photosmart 2610
Photosmart 2710
Patches for other models may be available here.
This patch has been well tested, with over 1800 copies of this patch distributed via email since April 2007.
The zip file has two files
OJ7410.pdf contains detailed instructions to apply the patch. Opening this file requires Adobe Reader or a similar pdf viewer, available for free download.
hpo7x00t.gpd is the actual patch file.
To apply the patch download the zip file attached here. Extract the files into the %temp% directory, then open the OJ7410.pdf file and follow the instructions. If you have difficulty finding the %temp% directory you can find this directory by opening your "computer" folder and typing %temp% in the address bar.
Bob Headrick, HP Expert
I am not an employee of HP, I am a volunteer posting here on my own time.
If your problem is solved please click the "Accept as Solution" button ------------V
If my answer was helpful please click the "Thumbs Up" to say "Thank You"--V
This question was solved.
View Solution.
Attachments:
Officejet 7410 Vista Duplex Patch.zip ‏427 KB

[Placeholder for updates]
Message Edited by Bob_Headrick on 05-14-2009 12:39 PM
Bob Headrick, HP Expert
I am not an employee of HP, I am a volunteer posting here on my own time.
If your problem is solved please click the "Accept as Solution" button ------------V
If my answer was helpful please click the "Thumbs Up" to say "Thank You"--V

Similar Messages

Need generic print driver for Officejet 7210 all-in-one on Windows 8.1

Updated my Windows 8 to Windows 8.1, which removed my print driver for an Officejet 7210 all-in-one. Attempted to reinstall. Error that file not found. Followed detailed process to a tee (deleted temp files, removed startup programs, everything). Driver doesn't work but printer does with other computers. Printer is no longer supported and no help (but is in great working condition).
I'm looking for a generic driver that would work with my printer and Windows 8.1. I really appreciate any help...
This question was solved.
View Solution.

Hi LChristofaro,
I have researched your error message and the Msiexec.exe error and it is an issue with windows installer. I recommend restarting your windows installer.
To do this:
1. Run "Services.msc" (without the quotation marks).
2. Double-click "Windows Installer" in the Services list.
3. Click Stop and click OK.
4. Click Start and click OK.
Restart you computer and try the install again.
Let me know if this helped.
Thank you,
I worked on behalf of HP.

New patches for SAP GUI 6.40 and the Screenreader Extension

Hi,
patch 10 for SAP GUI 6.40 and version 8 of the screenreader extension have been published on service.sap.com and ftp.sap.com.
Best regards,
Christian

Hi John,
short update: I talked to the service market place team, and unfortunately the software corner is not a standard SMP site, so the nice features you know from other pages are not available, and won't be in the near future.
I will post news about new patches here, but as mentioned this is not part of the official workflow and may not always happen, for example when I'm on vacation
Best regards,
Christian

Duplex Printing for Officejet 5740

I recently purchased an Officejet All-In-One 5740 printer. I did not realize that automatic duplex was a default and not an option. I can't find a way to change to 1-sided print (there is no selection in Properties). Is there an allowance for 1-sided print for this model printer?
This question was solved.
View Solution.

Hi,
From the application used to print open teh Print dialog, then click on Properties / Settings / Preferences to access the Printing Preferences dialog.
Within the Layout tab set Two-Sided printing as Off, confirm the changes and try printing again.
Additionally from the Control Panel open Devices and Printersm right click the printer icon and select Printing Preferences.
Ensure the same that Two-Sided printing is disabled to ensure it is diabled by default.
Regards,
Shlomi
Say thanks by clicking the Kudos thumb up in the post.
If my post resolve your problem please mark it as an Accepted Solution

Duplexing unit for Officejet 6500

I've got hold of an Officejet 6500 to take to university with me next month. I'm thinking that a duplexing unit would be useful but HP UK don't have any and I can't find any online elsewhere (except HP USA, which would be a bit too expensive I reckon). The part number is CB057-67001, anyone know of a place where I might be able to get hold of one?

Hi there,
Could you provide the community with a little more information to help narrow troubleshooting? What operating system is this?
You can say thanks by clicking the Kudos Star in my post. If my post resolves your problem, please mark it as Accepted Solution so others can benefit too.

Patch for ESSBASE 11.1.2.2

Hi All,
I had Applied patch for
1. Shared Servcies 11.1.2.2 (14020629) .300patch
2.EPM Workspace 11.1.2.2 (13936087).300patch
3.Planning 11.1.2.2 (13905088) .300patch
4.FDM & FOR ERPI 11.1.2.2 (14173894).300patch
i want to apply patch for Essbase 11.1.2.2 now can i do that ?. is there any sequence ,because i had applied patchs for shared services, workspace,planning and FDM earlier thats why - ?
i had applied patch for FDM 11.1.2.2 is this same patch applies for ERPI 11.1.2.2 also - ?
i got success message in command prompt when i applied patch for FDM , but once i open webclient and workbech client in help i am not able to find .300 new patch i applied for FDM
where can we check it -?

You can patch Essbase in any sequence, it will say in the readme if there are prereqs
Cheers
John
http://john-goodwin.blogspot..com/

Patch for report 3

can we download the patch for fixing the report margin and
rbwxpq.res not foung form oracle site?
please give the link for download, i am not able to run it on CD.
thanks in advance

hello,
oracle support services usually does not provide patches for
already de-supported products for download. you should contact
your local oracle support services to see if they can provide
you with this patch.
as far as i know, there are no patches for download other than
the ones for the most current products.
regards,
the oracle reports team --pw

Latest Patch for Oracle BPM 10.3.2

Hi,
I am using Oracle BPM 10g, I want to update that , I need latest patch/ hot fix for Oracle 10.3.2 with related jars and the steps for the update.
From where I can get all these documents, file and, updated files.
Thanks,
Brijesh Kumar Singh

From https://support.oracle.com/
You need a user to log and then Patches & Updates, click on Advanced Search, put Oracle Business Process Management Suite Release Oracle BPM 10.3.2 and click Search.
You will see the patches for Studio, Enterprise Stand Alone and Enterprise J2EE.
Download the one you want and the uncompressed and if it is Studio from Studio it self in File-->Updates-->Studio Local Update select the upd file.
If it is Enterprise has to be done through the AdminCenter.
HTH

Deskjet 710/720/810/820/1000 Series printers - Patch for 64 bit Vista and Windows 7

There is an issue with the 64 bit Vista, Windows 7 and Windows 8 or 8.1 drivers that causes the spooler to crash with the following HP Deskjet printers:
Deskjet 710
Deskjet 712
Deskjet 720
Deskjet 722
Deskjet 810
Deskjet 812
Deskjet 820
Deskjet 822
Deskjet 1000
The attached file contains a patch for this issue for Vista and Windows 7.
[The patch does not currently work for Windows 8 or 8.1 x64 systems. There are some efforts to address this, if a solution is developed it will be posted here. {Edit - I have not made any progress in getting the patch to work in Windows 8 x64.}]
First make sure the driver for the printer is installed. If the driver has not been installed go to Start, Devices and Printers, Add a Printer, Local Printer, choose the proper port (for USB-Parallel converters the port will likely be USB001: or perhaps USB002: ), Next, click Windows Update then choose HP for the manufacturer and select the appropriate printer.
Apply the patch as follows: Log into the computer with an administrative account. Download the patch by clicking on this link or on the paper clip at the end of this post. Save the patch file to your computer, then unzip it. Next copy the three DLL files to the following directory: %windir%\system32\spool\drivers\x64\3
Note that %windir% is a system variable that points to the location of the Windows directory. For most systems this will be C:\Windows. You can click Start, Computer and type %windir%\system32\spool\drivers\x64\3 in the address bar and it will find the right place.
This can be done from a DOS prompt if DOS is opened with the "run as administrator" command, or from explorer with a copy and paste. Depending on your UAC settings you may need to provide confirmation. Also allow the current files to be overwritten if prompted.
This patch is not required and should not applied to a 32 bit version of Vista or Windows 7.
Thanks to extraordinary Microsoft engineer Alan Morris for guidance for the patch.
Update - the following are more detailed installation instructions:
Download the patch from here. Now click on the file and open it, then extract the patch to some directory that is easy to find. (I use c:\temp. If this directory does not exist you can create it as follows: open the administrative DOS prompt by clicking on Start, All Programs, Accessories, then right click on CMD.EXE and select Run as Administrator. Click in the DOS box then type the following:
MD c:\temp
CD \temp
Now extract the patch files into the c:\temp directory (extract all, chose c:\temp as the destination).
[Update - Windows security settings may prevent these files from being used, please open Computer, type c:\temp in the address bar and then right click on each of the dll files and select Properties. If there is a message in Properties indicating the file was downloaded from the internet and may be blocked then unblock the file before proceeding.]
Next click back in the administrative DOS prompt and type the following: (stuff in green is comments, do not type them...)
DIR *.dll (this is just to verify the files are there, it should list hpvdb720.dll, hpvdb820.dll and hpwm5db1.dll and perhaps others.)
Net stop spooler (makes sure the files are not in use.)
Copy hpvdb720.dll C:\windows\system32\spool\drivers\x64\3 (this is for the Deskjet 710/712/720/722)
Copy hpvdb820.dll c:\windows\system32\spool\drivers\x64\3 (this covers the Deskjet 820 and 822)
Copy hpwm5db1.dll c:\windows\system32\spool\drivers\x64\3(this covers the Deskjet 1000)
Net Start Spooler
Exit
[Edit - note that these DLL files will already be in the directory. You will get a warning asking if it is OK to overwrite the files, say "yes".]
At this point the patch is installed and ready to print.
Note that the printers here do not support USB connections, they have only parallel ports. [Edit - if your printer does have a parallel port use it, this will likely be much less problematic than using a USB-Parallel converter.] If you use a USB-parallel converter make sure it is supported in your operating system. The following posts are flagged with USB-parallel cables that are reported to work in Windows 7.   A driver is required for the USB-parallel converter in addition to the driver for the printer. For supported converters this is typically supplied automatically in Windows 7. Note: the proper port to select for the USB-Parallel converters is often USB001:. I have heard of some cases where the port was USB002: or LPT3: as well. If the port you are using does not succeed (after applying the patch) try changing the port by going to Start, Devices and Printers, right click on your printer and select Printer Properties, then click on the Ports tab.
Bob Headrick, HP Expert
I am not an employee of HP, I am a volunteer posting here on my own time.
If your problem is solved please click the "Accept as Solution" button ------------V
If my answer was helpful please click the "Thumbs Up" to say "Thank You"--V
This question was solved.
View Solution.
Attachments:
DJ_Patch.zip ‏34 KB

Just want to send a thanks. Purchased a new HP computer with 64 bit Windows 7 and haven't been able to get my 722c to work. This patch worked like a charm!

Difficulty installing Rescue and Recovery 4.2 patch for Windows Vista

Which between System Update Installation History and Post-Installation Status Report should I believe, when they tell a different story?
When I run thinkVantage System Update, the post-intallation status report indicates that the following fails to install:
* Rescue and Recovery 4.2 patch for Windows Vista
* ThinkVantage Client Security Solution for Vista SP1
* Lenovo Wireless WAN Activation Patch
However, when I open the ThinkVantage System Update History Log, I read that the above updates have been installed.
Which one should I believe?
I'm willing to believe that the update has been installed, but whenever I run System Update, I keep getting the same message that the above three need to be installed.
Should I keep ignoring the message? If not, what else could I try?
I have a T60 running Vista with SP1 installed.

Hi privard,
Thanks for your feedback. Anyhow, let me see how i could help to sort this out for you.
Cleo
WW Social Media
T61, T410, x240, Z500, Flex 14
Important Note: If you need help, post your question in the forum, and include your system type, model number and OS. Do not post your serial number.
Did someone help you today? Press the star on the left to thank them with a Kudo!
If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"!
Follow @LenovoForums on Twitter!
How to send a private message? --> Check out this article.
English Community Deutsche Community Comunidad en Español Русскоязычное Сообщество

Officejet 7210 all-in-one duplex problem

Since connecting Officejet 7210 to laptop running Vista Business, the 2-sided printing accessory with rear tray is not recognised. I have been using the Deskjet 990C driver for 2-sided printing but it does not recognise the rear tray. Am unable to print photos using the rear tray, & when I try to load the 4x6 photo paper into main tray, the image will only print from the centre position of an A4 page, not the location when the tray is adjusted for the 4x6 (10cm x 15cm) stock. How can I enable the rear tray to feed the photo stock.
Is there an updated driver for the 7210 that supports the duplexer with rear tray or what other workaround can you recommend?
This question was solved.
View Solution.

Since the duplexer and rear tray were optional on the Officejet 7210 the driver will default to them being "not installed". Go to the printers folder, right click on the 7210, Properties, Device settings, Installable Options and set the Duplex Unit and the Rear Tray to installed, Apply, OK.
Once this is done the rear tray should be accessible and you can try duplex printing. You will probably need a patch to correct the back side printing upside down when duplexing, this is available as described here.
Regards,
Bob Headrick, MS MVP Printing/Imaging
Bob Headrick, HP Expert
I am not an employee of HP, I am a volunteer posting here on my own time.
If your problem is solved please click the "Accept as Solution" button ------------V
If my answer was helpful please click the "Thumbs Up" to say "Thank You"--V

Firmware upgrade for Officejet 4500 G510n-z

Please. i need the firmware upgrade for Officejet 4500 G510n-z or at the original firmware. my machine is acting uncommon. The paper feeder process start and page stop in the middle.
thanks for all your help.
Regards;
Carlos Peguero

Yes, there should have been either a firmware update/patch, or a full recall on this device.
The software setup and configuration is bad enough for one humble computer, but when used as
intended with multiple devices it's an absolute headache.
I am constantly having to unplug the printer because the machine has decided it needs to rest for a bit. Okay,
everybody deserves a break now and then. But it goes into coma mode and I could be jesus himself and the power
or any other button) still would not wake it.
I would get into the rest but I'm not getting a helpful vibe from the forum; it's more defensive of a product which, apparently just under 5000 people have come by to check on. My friend at Microsoft talked to an HP engineer, who
laughed and gave us the fix.
Uploading to FedEx-Kinko's is the better option.

Patch for cluster upgrade from 10201-10203

Hi,
i want to upgrade my cluster from 10.2.0.1 to 10.2.0.3
can somebody help me in finding the upgrade patch from 10.2.0.1 to 10.2.0.3
Thanks
Bala

patch for which operating system? and why you would like to patch 10203 ?
if you have metalink account you can download latest patches and documentation for particular patches.
search metalink knowledge tab for documentation.
for LINUX os patch download from metalink oracle support select tab patch&upgrade and search the patch i already mentioned.
for windows and mac os you can directly download from OTN.
http://www.oracle.com/technetwork/database/enterprise-edition/downloads/index.html
Oracle Database 10g Release 2 (10.2.0.4) for MAC OS X on Intel x86-64
Oracle Database 10g Release 2 (10.2.0.4) for Microsoft Windows Vista x64 and Microsoft Windows Server 2008 x64
Oracle Database 10g Release 2 (10.2.0.3/10.2.0.4) for Microsoft Windows Vista and Windows 2008

How to get and install 10.2.0.3 patch for Oracle XE (express)

Total newby here, pardon the stupid question....
I've installed Oracle XE but I've been told I need the patch that updates the database to 10.2.0.3. I can only find a patch for Vista, I'm on XP. When I go to the metalink(?) page it says I need to have a support ID.
How do I get a support ID (free) for XE, or is there something I'm missing.
Thx,
Mark

1) Just for sanity, I'm assuming that you posted a Metalink Note ID, not a bug. Metalink Note 334968.1 refers to bug 3807408.
2) The patches referenced in that bug would appear to relate to the Oracle client. Assuming proper licenses, I would expect that you could patch the Oracle clients accessing the XE database and resolve the issue.
3) The Metalink note references an alternate workaround of installing Visual Studio in a non-default location that doesn't include parenthesis.
Justin

Cannot install patch for cs5

While trying to figure out a problem minimizing files, which turned out not to be a problem, I discovered a patch for cs5. I could not install the patch. I then uninstalled cs5, re-installed it, shut off my virus protection, downloaded the patch first with firefox and then with explore and when win zip opens the downlaod and i go to install the patch I get an error message.
I have a Dell Inspioron, Windows 7 Home Premium,
Any help?
Thanks

That was still pretty terse.
It's not a problem to copy the entire log and post it here. Often times deep in the log there will be an error message that helps identify the problem.
With so little info to go on, these very generic suggestions come to mind:
1. Clear your Internet cache and download the update again to ensure you did not get a corrupted copy.
2. Close down all other software on your computer while installing, including temporarily disabling your antivirus.
3. If you have XP, make sure you're an admin. If running Vista or Win 7 run the installer As Administrator.
Note: If disabling your antivirus software helps the install process, you should consider tearing it out entirely and getting a better antivirus package.
-Noel

Vista/Wind​ows 7 Duplex Patch for Officejet 7210 7310 7410 and Photosmart 2610 2710

Similar Messages

Maybe you are looking for

Vista/Windows 7 Duplex Patch for Officejet 7210 7310 7410 and Photosmart 2610 2710