Vlan routing with Linksys sge2000
hi I have a Linksys sge2000 with two vlans, one has interface 192.168.50.10 /18 and the second has 192.168.30.10 /24, I need to get communication between these networks, because few computers must access to other network, so that’s why I ask you for some help, because until now I couldn’t find if its possible in this switch thank you in advanceDaniel
it is not possible for those 2 vlans to communicate with each other unless you hook up a router to those 2 vlans. the device is not capable for inter vlan routing alone so you will need to use layer 3 device.
Similar Messages
-
Vlan routing with cisco router and linksys switch
I have a linksys switch width vlan configured, connected to a Cisco router (1841), but I cant route between vlans.
Please help me!!
It Works with a Cisco switch perfectly(with the same ip and vlan).Yes. the linksys switch (SRW2024 24-Port 10/100/1000 Gigabit Switch) supports trunking.
If you want you can visit the link and see that the switch supports vlan, dot1q and trunking.
http://www.linksys.com/servlet/Satellite?childpagename=US%2FLayout&packedargs=c%3DL_Product_C2%26cid%3D1123638180432&pagename=Linksys%2FCommon%2FVisitorWrapper -
Migrate network segment to vlan routing with dlsw+
Currently, the dlsw are terminated on the core router which has token ring interface. The rest of the network are segmented using ethernet interface on the core router.
I need to migrate the network segment on the core router to cat6509 which will run inter-vlan routing.
My concern is when I move down the bridge group from the router ethernet, any issue will arise?
core router core router
| |
cat6509--------cat6509Hi,
My HQ router running SRB/TB to allow ethernet segment at HQ router to access IBM host. There is an active dlsw peer to BR1 and backup peer to BR2.
L1 and L2 are links between gigabit interface to routed port at core switch which running bridge group 1.
CS2 will be the root for vlan 20,40,200. CS1 will be the root for vlan 10,30,100.
L3 and L4 are trunk link to CS1 and CS2. AS1 is connected to DS1 on a port assigned to VLAN200. SNA client is on vlan 200.
Vlan 20,40,200 are assigned to bridge group 1.
For normal operation, SNA client establish circuit to the host. From CS1, I can see host mac address learn through bridge which is from gigabit interface connected to BR1. From CS2, I can see the host mac address learn through port channel.
When L4 link down, the circuit still maintain with interruption. This time CS2 does not display any host mac address due DS1 will forward vlan 200 to CS1. The SNA traffic will go direct to BR1.
During L4 recover ( meaning reconnect back the lost connection), I can see host mac address learn through vlan 20,40,200.
After the mac aging, all mac address disappear and I cant establish any SNA session. What could be the problem for this? -
Inter VLAN Routing with ASA 5520 and Cat 2960
Hi there,
I am a complete novice at networking, but I was tasked to have an ASA 5520 do inter VLAN routing (since my shop doesn't have a layer 3 router).
As a basic setup, I am trying to have three workstations on three different VLANs communicate with each other. The attached screenshot shows the topology.
I am unable to ping from a PC to the ASA...therefore I can't ping to other VLANs. Any assistance would be greatly appreciated.
ROUTER CONFIG:
ciscoasa#
ciscoasa# show run
: Saved
ASA Version 8.3(1)
hostname ciscoasa
domain-name null
enable password ###### encrypted
passwd ###### encrypted
names
dns-guard
interface GigabitEthernet0/0
no nameif
no security-level
no ip address
interface GigabitEthernet0/1
no nameif
security-level 100
ip address 10.10.1.1 255.255.255.0
interface GigabitEthernet0/1.10
vlan 10
nameif vlan10
security-level 100
ip address 10.10.10.1 255.255.255.0
interface GigabitEthernet0/1.20
vlan 20
nameif vlan20
security-level 100
ip address 10.10.20.1 255.255.255.0
interface GigabitEthernet0/1.30
vlan 30
nameif vlan30
security-level 100
ip address 10.10.30.1 255.255.255.0
interface GigabitEthernet0/2
shutdown
no nameif
no security-level
no ip address
interface GigabitEthernet0/3
shutdown
no nameif
no security-level
no ip address
interface Management0/0
nameif inside
security-level 100
ip address 192.168.1.1 255.255.255.0
management-only
boot system disk0:/asa831-k8.bin
ftp mode passive
dns server-group DefaultDNS
domain-name null
same-security-traffic permit inter-interface
same-security-traffic permit intra-interface
access-list global_access extended permit icmp any any
pager lines 24
logging enable
logging asdm informational
mtu inside 1500
mtu vlan10 1500
mtu vlan20 1500
mtu vlan30 1500
no failover
icmp unreachable rate-limit 1 burst-size 1
icmp permit any inside
asdm image disk0:/asdm-631.bin
no asdm history enable
arp timeout 14400
access-group global_access global
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-record DfltAccessPolicy
http server enable
http 192.168.1.0 255.255.255.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec security-association lifetime seconds 28800
crypto ipsec security-association lifetime kilobytes 4608000
telnet timeout 5
ssh timeout 5
console timeout 0
management-access inside
dhcpd address 192.168.1.2-192.168.1.5 inside
dhcpd enable inside
dhcpd address 10.10.10.101-10.10.10.253 vlan10
dhcpd enable vlan10
dhcpd address 10.10.20.101-10.10.20.253 vlan20
dhcpd enable vlan20
dhcpd address 10.10.30.101-10.10.30.253 vlan30
dhcpd enable vlan30
threat-detection basic-threat
threat-detection statistics host
threat-detection statistics port
threat-detection statistics protocol
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
webvpn
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns migrated_dns_map_1
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns migrated_dns_map_1
inspect ftp
inspect h323 h225
inspect h323 ras
inspect netbios
inspect rsh
inspect rtsp
inspect skinny
inspect esmtp
inspect sqlnet
inspect sunrpc
inspect tftp
inspect sip
inspect xdmcp
inspect ip-options
service-policy global_policy global
prompt hostname context
call-home
profile CiscoTAC-1
no active
destination address http https://tools.cisco.com/its/service/oddce/services/DD
CEService
destination address email [email protected]
destination transport-method http
subscribe-to-alert-group diagnostic
subscribe-to-alert-group environment
subscribe-to-alert-group inventory periodic monthly
subscribe-to-alert-group configuration periodic monthly
subscribe-to-alert-group telemetry periodic daily
Cryptochecksum:4ad1bba72f1f51b2a47e8cacb9d3606a
: end
SWITCH CONFIG
Switch#show run
Building configuration...
Current configuration : 2543 bytes
version 12.2
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname Switch
boot-start-marker
boot-end-marker
no aaa new-model
system mtu routing 1500
ip subnet-zero
spanning-tree mode pvst
spanning-tree extend system-id
no spanning-tree vlan 1
vlan internal allocation policy ascending
interface GigabitEthernet0/1
description Port Configured As Trunk
switchport trunk allowed vlan 1,10,20,30,1002-1005
switchport mode trunk
interface GigabitEthernet0/2
switchport access vlan 10
switchport mode access
interface GigabitEthernet0/3
switchport access vlan 20
switchport mode access
interface GigabitEthernet0/4
switchport access vlan 30
switchport mode access
interface GigabitEthernet0/5
interface GigabitEthernet0/6
interface GigabitEthernet0/7
interface GigabitEthernet0/8
interface GigabitEthernet0/9
interface GigabitEthernet0/10
interface GigabitEthernet0/11
interface GigabitEthernet0/12
interface GigabitEthernet0/13
interface GigabitEthernet0/14
interface GigabitEthernet0/15
interface GigabitEthernet0/16
interface GigabitEthernet0/17
interface GigabitEthernet0/18
interface GigabitEthernet0/19
interface GigabitEthernet0/20
interface GigabitEthernet0/21
interface GigabitEthernet0/22
interface GigabitEthernet0/23
interface GigabitEthernet0/24
interface GigabitEthernet0/25
interface GigabitEthernet0/26
interface GigabitEthernet0/27
interface GigabitEthernet0/28
interface GigabitEthernet0/29
interface GigabitEthernet0/30
interface GigabitEthernet0/31
interface GigabitEthernet0/32
interface GigabitEthernet0/33
interface GigabitEthernet0/34
interface GigabitEthernet0/35
interface GigabitEthernet0/36
interface GigabitEthernet0/37
interface GigabitEthernet0/38
interface GigabitEthernet0/39
interface GigabitEthernet0/40
interface GigabitEthernet0/41
interface GigabitEthernet0/42
interface GigabitEthernet0/43
interface GigabitEthernet0/44
interface GigabitEthernet0/45
interface GigabitEthernet0/46
interface GigabitEthernet0/47
interface GigabitEthernet0/48
interface Vlan1
ip address 10.10.1.2 255.255.255.0
no ip route-cache
interface Vlan10
no ip address
no ip route-cache
interface Vlan20
no ip address
no ip route-cache
interface Vlan30
no ip address
no ip route-cache
ip default-gateway 10.10.1.1
ip http server
ip http secure-server
control-plane
line con 0
line vty 5 15
endciscoasa# capture cap10 interface vlan10
ciscoasa# capture cap20 interface vlan20
ciscoasa# show cap cap10
97 packets captured
1: 17:32:32.541262 802.1Q vlan#10 P0 10.10.10.101.2461 > 10.10.10.1.8905: ud
p 96
2: 17:32:36.741294 802.1Q vlan#10 P0 10.10.10.101 > 10.10.10.1: icmp: echo re
quest
3: 17:32:36.741523 802.1Q vlan#10 P0 10.10.10.1 > 10.10.10.101: icmp: echo re
ply
4: 17:32:37.539217 802.1Q vlan#10 P0 10.10.10.101.2462 > 10.10.10.1.8905: ud
p 98
5: 17:32:39.104914 802.1Q vlan#10 P0 10.10.10.101.2463 > 10.12.5.64.8906: ud
p 95
6: 17:32:41.738914 802.1Q vlan#10 P0 10.10.10.101 > 10.10.10.1: icmp: echo re
quest
7: 17:32:41.739143 802.1Q vlan#10 P0 10.10.10.1 > 10.10.10.101: icmp: echo re
ply
8: 17:32:42.544023 802.1Q vlan#10 P0 10.10.10.101.2464 > 10.10.10.1.8905: ud
p 93
9: 17:32:46.747352 802.1Q vlan#10 P0 10.10.10.101 > 10.10.10.1: icmp: echo re
quest
10: 17:32:46.747580 802.1Q vlan#10 P0 10.10.10.1 > 10.10.10.101: icmp: echo re
ply
11: 17:32:47.546633 802.1Q vlan#10 P0 10.10.10.101.2465 > 10.10.10.1.8905: ud
p 98
12: 17:32:51.739921 802.1Q vlan#10 P0 10.10.10.101 > 10.10.10.1: icmp: echo re
quest
13: 17:32:51.740150 802.1Q vlan#10 P0 10.10.10.1 > 10.10.10.101: icmp: echo re
ply
14: 17:32:52.544100 802.1Q vlan#10 P0 10.10.10.101.2466 > 10.10.10.1.8905: ud
p 98
15: 17:32:56.741859 802.1Q vlan#10 P0 10.10.10.101 > 10.10.10.1: icmp: echo re
quest
16: 17:32:56.742088 802.1Q vlan#10 P0 10.10.10.1 > 10.10.10.101: icmp: echo re
ply
17: 17:32:57.547396 802.1Q vlan#10 P0 10.10.10.101.2467 > 10.10.10.1.8905: ud
p 98
18: 17:33:01.742728 802.1Q vlan#10 P0 10.10.10.101 > 10.10.10.1: icmp: echo re
quest
19: 17:33:01.742957 802.1Q vlan#10 P0 10.10.10.1 > 10.10.10.101: icmp: echo re
ply
20: 17:33:02.547609 802.1Q vlan#10 P0 10.10.10.101.2468 > 10.10.10.1.8905: ud
p 97
21: 17:33:06.742774 802.1Q vlan#10 P0 10.10.10.101 > 10.10.10.1: icmp: echo re
quest
22: 17:33:06.743018 802.1Q vlan#10 P0 10.10.10.1 > 10.10.10.101: icmp: echo re
ply
23: 17:33:07.543337 802.1Q vlan#10 P0 10.10.10.101.2469 > 10.10.10.1.8905: ud
p 93
24: 17:33:10.375514 802.1Q vlan#10 P0 10.10.10.101.137 > 10.10.10.255.137: ud
p 50
25: 17:33:11.114679 802.1Q vlan#10 P0 10.10.10.101.137 > 10.10.10.255.137: ud
p 50
26: 17:33:11.742728 802.1Q vlan#10 P0 10.10.10.101 > 10.10.10.1: icmp: echo re
quest
27: 17:33:11.742957 802.1Q vlan#10 P0 10.10.10.1 > 10.10.10.101: icmp: echo re
ply
28: 17:33:11.864731 802.1Q vlan#10 P0 10.10.10.101.137 > 10.10.10.255.137: ud
p 50
29: 17:33:12.546266 802.1Q vlan#10 P0 10.10.10.101.2470 > 10.10.10.1.8905: ud
p 98
30: 17:33:16.746497 802.1Q vlan#10 P0 10.10.10.101 > 10.10.10.1: icmp: echo re
quest
31: 17:33:16.746726 802.1Q vlan#10 P0 10.10.10.1 > 10.10.10.101: icmp: echo re
ply
32: 17:33:17.548403 802.1Q vlan#10 P0 10.10.10.101.2471 > 10.10.10.1.8905: ud
p 97
33: 17:33:21.744880 802.1Q vlan#10 P0 10.10.10.101 > 10.10.10.1: icmp: echo re
quest
34: 17:33:21.745109 802.1Q vlan#10 P0 10.10.10.1 > 10.10.10.101: icmp: echo re
ply
35: 17:33:22.545351 802.1Q vlan#10 P0 10.10.10.101.2472 > 10.10.10.1.8905: ud
p 95
36: 17:33:23.785558 802.1Q vlan#10 P0 10.10.10.101.137 > 10.10.10.255.137: ud
p 50
37: 17:33:24.522464 802.1Q vlan#10 P0 10.10.10.101.137 > 10.10.10.255.137: ud
p 50
38: 17:33:25.272568 802.1Q vlan#10 P0 10.10.10.101.137 > 10.10.10.255.137: ud
p 50
39: 17:33:26.744926 802.1Q vlan#10 P0 10.10.10.101 > 10.10.10.1: icmp: echo re
quest
40: 17:33:26.745154 802.1Q vlan#10 P0 10.10.10.1 > 10.10.10.101: icmp: echo re
ply
41: 17:33:27.548708 802.1Q vlan#10 P0 10.10.10.101.2473 > 10.10.10.1.8905: ud
p 96
42: 17:33:31.749625 802.1Q vlan#10 P0 10.10.10.101 > 10.10.10.1: icmp: echo re
quest
43: 17:33:31.749854 802.1Q vlan#10 P0 10.10.10.1 > 10.10.10.101: icmp: echo re
ply
44: 17:33:32.550096 802.1Q vlan#10 P0 10.10.10.101.2474 > 10.10.10.1.8905: ud
p 97
45: 17:33:36.748343 802.1Q vlan#10 P0 10.10.10.101 > 10.10.10.1: icmp: echo re
quest
46: 17:33:36.748572 802.1Q vlan#10 P0 10.10.10.1 > 10.10.10.101: icmp: echo re
ply
47: 17:33:37.546251 802.1Q vlan#10 P0 10.10.10.101.2475 > 10.10.10.1.8905: ud
p 95
48: 17:33:41.745566 802.1Q vlan#10 P0 10.10.10.101 > 10.10.10.1: icmp: echo re
quest
49: 17:33:41.745795 802.1Q vlan#10 P0 10.10.10.1 > 10.10.10.101: icmp: echo re
ply
50: 17:33:42.547975 802.1Q vlan#10 P0 10.10.10.101.2476 > 10.10.10.1.8905: ud
p 97
51: 17:33:46.747855 802.1Q vlan#10 P0 10.10.10.101 > 10.10.10.1: icmp: echo re
quest
52: 17:33:46.748084 802.1Q vlan#10 P0 10.10.10.1 > 10.10.10.101: icmp: echo re
ply
53: 17:33:47.548403 802.1Q vlan#10 P0 10.10.10.101.2477 > 10.10.10.1.8905: ud
p 94
54: 17:33:51.747718 802.1Q vlan#10 P0 10.10.10.101 > 10.10.10.1: icmp: echo re
quest
55: 17:33:51.747931 802.1Q vlan#10 P0 10.10.10.1 > 10.10.10.101: icmp: echo re
ply
56: 17:33:52.547670 802.1Q vlan#10 P0 10.10.10.101.2478 > 10.10.10.1.8905: ud
p 97
57: 17:33:54.134239 802.1Q vlan#10 P0 10.10.10.101 > 10.10.20.101: icmp: echo
request
58: 17:33:56.750678 802.1Q vlan#10 P0 10.10.10.101 > 10.10.10.1: icmp: echo re
quest
59: 17:33:56.750891 802.1Q vlan#10 P0 10.10.10.1 > 10.10.10.101: icmp: echo re
ply
60: 17:33:57.563035 802.1Q vlan#10 P0 10.10.10.101.2479 > 10.10.10.1.8905: ud
p 97
61: 17:33:59.245272 802.1Q vlan#10 P0 10.10.10.101 > 10.10.20.101: icmp: echo
request
62: 17:34:01.752188 802.1Q vlan#10 P0 10.10.10.101 > 10.10.10.1: icmp: echo re
quest
63: 17:34:01.752402 802.1Q vlan#10 P0 10.10.10.1 > 10.10.10.101: icmp: echo re
ply
64: 17:34:01.995737 802.1Q vlan#10 P0 10.10.10.101.2263 > 156.80.16.23.427: u
dp 49
65: 17:34:01.995813 802.1Q vlan#10 P0 10.10.10.101.2263 > 156.80.16.23.427: u
dp 34
66: 17:34:01.995950 802.1Q vlan#10 P0 10.10.10.101.2263 > 156.80.16.22.427: u
dp 49
67: 17:34:01.996011 802.1Q vlan#10 P0 10.10.10.101.2263 > 156.80.16.22.427: u
dp 34
68: 17:34:01.996118 802.1Q vlan#10 P0 10.10.10.101.2263 > 156.80.200.40.427:
udp 49
69: 17:34:01.996179 802.1Q vlan#10 P0 10.10.10.101.2263 > 156.80.200.40.427:
udp 34
70: 17:34:02.551836 802.1Q vlan#10 P0 10.10.10.101.2480 > 10.10.10.1.8905: ud
p 98
71: 17:34:03.011306 802.1Q vlan#10 P0 10.10.10.101.2263 > 156.80.16.23.427: u
dp 49
72: 17:34:03.011367 802.1Q vlan#10 P0 10.10.10.101.2263 > 156.80.16.23.427: u
dp 34
73: 17:34:03.011443 802.1Q vlan#10 P0 10.10.10.101.2263 > 156.80.16.22.427: u
dp 49
74: 17:34:03.011489 802.1Q vlan#10 P0 10.10.10.101.2263 > 156.80.16.22.427: u
dp 34
75: 17:34:03.011550 802.1Q vlan#10 P0 10.10.10.101.2263 > 156.80.200.40.427:
udp 49
76: 17:34:03.011596 802.1Q vlan#10 P0 10.10.10.101.2263 > 156.80.200.40.427:
udp 34
77: 17:34:04.027037 802.1Q vlan#10 P0 10.10.10.101.2263 > 156.80.16.23.427: u
dp 49
78: 17:34:04.027082 802.1Q vlan#10 P0 10.10.10.101.2263 > 156.80.16.23.427: u
dp 34
79: 17:34:04.027174 802.1Q vlan#10 P0 10.10.10.101.2263 > 156.80.16.22.427: u
dp 49
80: 17:34:04.027250 802.1Q vlan#10 P0 10.10.10.101.2263 > 156.80.16.22.427: u
dp 34
81: 17:34:04.027311 802.1Q vlan#10 P0 10.10.10.101.2263 > 156.80.200.40.427:
udp 49
82: 17:34:04.027357 802.1Q vlan#10 P0 10.10.10.101.2263 > 156.80.200.40.427:
udp 34
83: 17:34:04.745811 802.1Q vlan#10 P0 10.10.10.101 > 10.10.20.101: icmp: echo
request
84: 17:34:06.058514 802.1Q vlan#10 P0 10.10.10.101.2263 > 156.80.16.23.427: u
dp 49
85: 17:34:06.058605 802.1Q vlan#10 P0 10.10.10.101.2263 > 156.80.16.23.427: u
dp 34
86: 17:34:06.058651 802.1Q vlan#10 P0 10.10.10.101.2263 > 156.80.16.22.427: u
dp 49
87: 17:34:06.058712 802.1Q vlan#10 P0 10.10.10.101.2263 > 156.80.16.22.427: u
dp 34
88: 17:34:06.058758 802.1Q vlan#10 P0 10.10.10.101.2263 > 156.80.200.40.427:
udp 49
89: 17:34:06.058819 802.1Q vlan#10 P0 10.10.10.101.2263 > 156.80.200.40.427:
udp 34
90: 17:34:06.750907 802.1Q vlan#10 P0 10.10.10.101 > 10.10.10.1: icmp: echo re
quest
91: 17:34:06.751151 802.1Q vlan#10 P0 10.10.10.1 > 10.10.10.101: icmp: echo re
ply
92: 17:34:07.552751 802.1Q vlan#10 P0 10.10.10.101.2481 > 10.10.10.1.8905: ud
p 96
93: 17:34:11.752082 802.1Q vlan#10 P0 10.10.10.101 > 10.10.10.1: icmp: echo re
quest
94: 17:34:11.752326 802.1Q vlan#10 P0 10.10.10.1 > 10.10.10.101: icmp: echo re
ply
95: 17:34:12.553392 802.1Q vlan#10 P0 10.10.10.101.2482 > 10.10.10.1.8905: ud
p 96
96: 17:34:16.755438 802.1Q vlan#10 P0 10.10.10.101 > 10.10.10.1: icmp: echo re
quest
97: 17:34:16.755682 802.1Q vlan#10 P0 10.10.10.1 > 10.10.10.101: icmp: echo re
ply
98: 17:34:17.554811 802.1Q vlan#10 P0 10.10.10.101.2483 > 10.10.10.1.8905: ud
p 97
99: 17:34:21.751303 802.1Q vlan#10 P0 10.10.10.101 > 10.10.10.1: icmp: echo re
quest
100: 17:34:21.751563 802.1Q vlan#10 P0 10.10.10.1 > 10.10.10.101: icmp: echo re
ply
101: 17:34:22.552034 802.1Q vlan#10 P0 10.10.10.101.2484 > 10.10.10.1.8905: ud
p 95
102: 17:34:26.753989 802.1Q vlan#10 P0 10.10.10.101 > 10.10.10.1: icmp: echo re
quest
103: 17:34:26.754218 802.1Q vlan#10 P0 10.10.10.1 > 10.10.10.101: icmp: echo re
ply
104: 17:34:27.560334 802.1Q vlan#10 P0 10.10.10.101.2485 > 10.10.10.1.8905: ud
p 98
105: 17:34:31.755499 802.1Q vlan#10 P0 10.10.10.101 > 10.10.10.1: icmp: echo re
quest
106: 17:34:31.755728 802.1Q vlan#10 P0 10.10.10.1 > 10.10.10.101: icmp: echo re
ply
107: 17:34:32.563950 802.1Q vlan#10 P0 10.10.10.101.2486 > 10.10.10.1.8905: ud
p 95
107 packets shown
ciscoasa# show cap cap20
92 packets captured
1: 17:26:53.653378 802.1Q vlan#20 P0 10.10.20.101.1187 > 216.49.94.13.80: S 8
20343450:820343450(0) win 65535
2: 17:27:12.019133 802.1Q vlan#20 P0 10.10.10.101 > 10.10.20.101: icmp: echo
request
3: 17:27:17.214481 802.1Q vlan#20 P0 10.10.10.101 > 10.10.20.101: icmp: echo
request
4: 17:27:55.593688 802.1Q vlan#20 P0 10.10.20.101.1188 > 216.49.94.13.80: S 1
499891746:1499891746(0) win 65535
5: 17:27:58.555284 802.1Q vlan#20 P0 10.10.20.101.1188 > 216.49.94.13.80: S 1
499891746:1499891746(0) win 65535
6: 17:28:04.564790 802.1Q vlan#20 P0 10.10.20.101.1188 > 216.49.94.13.80: S 1
499891746:1499891746(0) win 65535
7: 17:29:06.504856 802.1Q vlan#20 P0 arp who-has 10.10.20.1 tell 10.10.20.101
8: 17:29:06.504917 802.1Q vlan#20 P0 arp reply 10.10.20.1 is-at 54:75:d0:ba:4
6:bb
9: 17:29:06.505222 802.1Q vlan#20 P0 10.10.20.101.1189 > 216.49.94.13.80: S 4
7080594:47080594(0) win 65535
10: 17:29:09.467032 802.1Q vlan#20 P0 10.10.20.101.1189 > 216.49.94.13.80: S 4
7080594:47080594(0) win 65535
11: 17:29:15.476537 802.1Q vlan#20 P0 10.10.20.101.1189 > 216.49.94.13.80: S 4
7080594:47080594(0) win 65535
12: 17:30:17.417245 802.1Q vlan#20 P0 10.10.20.101.1190 > 216.49.94.13.80: S 1
445997597:1445997597(0) win 65535
13: 17:30:18.156043 802.1Q vlan#20 P0 10.10.10.101 > 10.10.20.101: icmp: echo
request
14: 17:30:20.378688 802.1Q vlan#20 P0 10.10.20.101.1190 > 216.49.94.13.80: S 1
445997597:1445997597(0) win 65535
15: 17:30:23.220356 802.1Q vlan#20 P0 10.10.10.101 > 10.10.20.101: icmp: echo
request
16: 17:30:26.388102 802.1Q vlan#20 P0 10.10.20.101.1190 > 216.49.94.13.80: S 1
445997597:1445997597(0) win 65535
17: 17:30:28.721047 802.1Q vlan#20 P0 10.10.10.101 > 10.10.20.101: icmp: echo
request
18: 17:30:34.222507 802.1Q vlan#20 P0 10.10.10.101 > 10.10.20.101: icmp: echo
request
19: 17:33:43.156928 802.1Q vlan#20 P0 arp who-has 10.10.20.101 tell 10.10.20.1
01
20: 17:33:44.187002 802.1Q vlan#20 P0 arp who-has 10.10.20.1 tell 10.10.20.101
21: 17:33:44.187047 802.1Q vlan#20 P0 arp reply 10.10.20.1 is-at 54:75:d0:ba:4
6:bb
22: 17:33:44.187261 802.1Q vlan#20 P0 10.10.20.101 > 10.10.20.1: icmp: echo re
quest
23: 17:33:44.187520 802.1Q vlan#20 P0 10.10.20.1 > 10.10.20.101: icmp: echo re
ply
24: 17:33:44.239016 802.1Q vlan#20 P0 10.10.20.101.137 > 10.10.20.255.137: ud
p 68
25: 17:33:44.327360 802.1Q vlan#20 P0 10.10.20.101.53835 > 208.231.55.26.53:
udp 34
26: 17:33:44.989740 802.1Q vlan#20 P0 10.10.20.101.137 > 10.10.20.255.137: ud
p 68
27: 17:33:45.150611 802.1Q vlan#20 P0 10.10.20.101.6646 > 10.10.20.255.6646:
udp 236
28: 17:33:45.331312 802.1Q vlan#20 P0 10.10.20.101.53835 > 208.231.55.27.53:
udp 34
29: 17:33:45.740943 802.1Q vlan#20 P0 10.10.20.101.137 > 10.10.20.255.137: ud
p 68
30: 17:33:46.331892 802.1Q vlan#20 P0 10.10.20.101.53835 > 208.231.55.26.53:
udp 34
31: 17:33:46.492131 802.1Q vlan#20 P0 10.10.20.101.137 > 10.10.20.255.137: ud
p 68
32: 17:33:47.243502 802.1Q vlan#20 P0 10.10.20.101.137 > 10.10.20.255.137: ud
p 68
33: 17:33:47.994501 802.1Q vlan#20 P0 10.10.20.101.137 > 10.10.20.255.137: ud
p 68
34: 17:33:48.335050 802.1Q vlan#20 P0 10.10.20.101.53835 > 208.231.55.26.53:
udp 34
35: 17:33:48.335141 802.1Q vlan#20 P0 10.10.20.101.53835 > 208.231.55.27.53:
udp 34
36: 17:33:48.745658 802.1Q vlan#20 P0 10.10.20.101.137 > 10.10.20.255.137: ud
p 68
37: 17:33:49.496861 802.1Q vlan#20 P0 10.10.20.101.137 > 10.10.20.255.137: ud
p 68
38: 17:33:50.248812 802.1Q vlan#20 P0 10.10.20.101.137 > 10.10.20.255.137: ud
p 68
39: 17:33:50.249300 802.1Q vlan#20 P0 10.10.20.101.137 > 10.10.20.255.137: ud
p 68
40: 17:33:50.999170 802.1Q vlan#20 P0 10.10.20.101.137 > 10.10.20.255.137: ud
p 68
41: 17:33:50.999246 802.1Q vlan#20 P0 10.10.20.101.137 > 10.10.20.255.137: ud
p 68
42: 17:33:51.750342 802.1Q vlan#20 P0 10.10.20.101.137 > 10.10.20.255.137: ud
p 68
43: 17:33:51.750418 802.1Q vlan#20 P0 10.10.20.101.137 > 10.10.20.255.137: ud
p 68
44: 17:33:52.341336 802.1Q vlan#20 P0 10.10.20.101.53835 > 208.231.55.26.53:
udp 34
45: 17:33:52.341474 802.1Q vlan#20 P0 10.10.20.101.53835 > 208.231.55.27.53:
udp 34
46: 17:33:52.501576 802.1Q vlan#20 P0 10.10.20.101.137 > 10.10.20.255.137: ud
p 68
47: 17:33:52.501652 802.1Q vlan#20 P0 10.10.20.101.137 > 10.10.20.255.137: ud
p 68
48: 17:33:53.254183 802.1Q vlan#20 P0 10.10.20.101.138 > 10.10.20.255.138: ud
p 174
49: 17:33:53.254320 802.1Q vlan#20 P0 10.10.20.101.138 > 10.10.20.255.138: ud
p 204
50: 17:33:54.134361 802.1Q vlan#20 P0 10.10.10.101 > 10.10.20.101: icmp: echo
request
51: 17:33:54.755118 802.1Q vlan#20 P0 10.10.20.101.138 > 10.10.20.255.138: ud
p 174
52: 17:33:54.823535 802.1Q vlan#20 P0 10.120.2.198.1261 > 161.69.12.13.443: R
250934743:250934743(0) ack 2427374744 win 0
53: 17:33:54.823901 802.1Q vlan#20 P0 10.120.2.198.1262 > 161.69.12.13.443: R
3313764765:3313764765(0) ack 1397588942 win 0
54: 17:33:54.824618 802.1Q vlan#20 P0 10.10.20.101.1269 > 161.69.12.13.443: S
2860571026:2860571026(0) win 65535
55: 17:33:56.257448 802.1Q vlan#20 P0 10.10.20.101.138 > 10.10.20.255.138: ud
p 174
56: 17:33:57.759833 802.1Q vlan#20 P0 10.10.20.101.138 > 10.10.20.255.138: ud
p 174
57: 17:33:57.779729 802.1Q vlan#20 P0 10.10.20.101.1269 > 161.69.12.13.443: S
2860571026:2860571026(0) win 65535
58: 17:33:59.245394 802.1Q vlan#20 P0 10.10.10.101 > 10.10.20.101: icmp: echo
request
59: 17:33:59.262178 802.1Q vlan#20 P0 10.10.20.101.138 > 10.10.20.255.138: ud
p 186
60: 17:34:00.263780 802.1Q vlan#20 P0 10.10.20.101.138 > 10.10.20.255.138: ud
p 186
61: 17:34:01.265382 802.1Q vlan#20 P0 10.10.20.101.138 > 10.10.20.255.138: ud
p 186
62: 17:34:02.266908 802.1Q vlan#20 P0 10.10.20.101.138 > 10.10.20.255.138: ud
p 186
63: 17:34:03.268540 802.1Q vlan#20 P0 10.10.20.101.137 > 10.10.20.255.137: ud
p 68
64: 17:34:03.789189 802.1Q vlan#20 P0 10.10.20.101.1269 > 161.69.12.13.443: S
2860571026:2860571026(0) win 65535
65: 17:34:04.019591 802.1Q vlan#20 P0 10.10.20.101.137 > 10.10.20.255.137: ud
p 68
66: 17:34:04.745933 802.1Q vlan#20 P0 10.10.10.101 > 10.10.20.101: icmp: echo
request
67: 17:34:04.770757 802.1Q vlan#20 P0 10.10.20.101.137 > 10.10.20.255.137: ud
p 68
68: 17:34:05.521991 802.1Q vlan#20 P0 10.10.20.101.137 > 10.10.20.255.137: ud
p 68
69: 17:34:06.273209 802.1Q vlan#20 P0 10.10.20.101.137 > 10.10.20.255.137: ud
p 68
70: 17:34:07.024367 802.1Q vlan#20 P0 10.10.20.101.137 > 10.10.20.255.137: ud
p 68
71: 17:34:07.775518 802.1Q vlan#20 P0 10.10.20.101.137 > 10.10.20.255.137: ud
p 68
72: 17:34:08.526706 802.1Q vlan#20 P0 10.10.20.101.137 > 10.10.20.255.137: ud
p 68
73: 17:34:09.277939 802.1Q vlan#20 P0 10.10.20.101.138 > 10.10.20.255.138: ud
p 174
74: 17:34:09.278061 802.1Q vlan#20 P0 10.10.20.101.138 > 10.10.20.255.138: ud
p 174
75: 17:34:09.278702 802.1Q vlan#20 P0 10.10.20.101.138 > 10.10.20.255.138: ud
p 204
76: 17:34:15.810489 802.1Q vlan#20 P0 10.10.20.101.49796 > 208.231.55.26.53:
udp 31
77: 17:34:16.809726 802.1Q vlan#20 P0 10.10.20.101.49796 > 208.231.55.27.53:
udp 31
78: 17:34:17.811222 802.1Q vlan#20 P0 10.10.20.101.49796 > 208.231.55.26.53:
udp 31
79: 17:34:19.814349 802.1Q vlan#20 P0 10.10.20.101.49796 > 208.231.55.26.53:
udp 31
80: 17:34:19.814380 802.1Q vlan#20 P0 10.10.20.101.49796 > 208.231.55.27.53:
udp 31
81: 17:34:23.820682 802.1Q vlan#20 P0 10.10.20.101.49796 > 208.231.55.26.53:
udp 31
82: 17:34:23.820788 802.1Q vlan#20 P0 10.10.20.101.49796 > 208.231.55.27.53:
udp 31
83: 17:34:30.822924 802.1Q vlan#20 P0 10.10.20.101.137 > 10.10.20.255.137: ud
p 50
84: 17:34:31.572892 802.1Q vlan#20 P0 10.10.20.101.137 > 10.10.20.255.137: ud
p 50
85: 17:34:32.324079 802.1Q vlan#20 P0 10.10.20.101.137 > 10.10.20.255.137: ud
p 50
86: 17:34:33.083079 802.1Q vlan#20 P0 10.10.20.101.61089 > 208.231.55.26.53:
udp 44
87: 17:34:34.077007 802.1Q vlan#20 P0 10.10.20.101.61089 > 208.231.55.27.53:
udp 44
88: 17:34:35.078639 802.1Q vlan#20 P0 10.10.20.101.61089 > 208.231.55.26.53:
udp 44
89: 17:34:37.081584 802.1Q vlan#20 P0 10.10.20.101.61089 > 208.231.55.26.53:
udp 44
90: 17:34:37.081706 802.1Q vlan#20 P0 10.10.20.101.61089 > 208.231.55.27.53:
udp 44
91: 17:34:41.087809 802.1Q vlan#20 P0 10.10.20.101.61089 > 208.231.55.26.53:
udp 44
92: 17:34:41.087840 802.1Q vlan#20 P0 10.10.20.101.61089 > 208.231.55.27.53:
udp 44
92 packets shown -
Hookup Linksys Broadband Cable Router with Linksys Hub
Hello All,
New here and have ran into an issue and I thought what better place to go then to here for help.
Ok here is my situation. I am currently running cable internet with the LinkSys RT31P2 Broadband Router and the LinkSys EFAH05W 5 Port Workgroup Hub. I currently have 2 IP's one is shared and one is running 1 system as we have 3 computers.
I had issues awhile back with one of the IP's not registering after the cable company changed my IP addy's. They told me I had the hardware wired improperly and that was the cause of my issue. Well since then I got the one computer running on it's IP without changing anything. Now all the sudden that computer cannot connect to the internet again.
Here is the way I have it wired. Wire from Cable modem going into Hub (Uplink slot), then a Grey wire from the #1 slot in Hub running to router (Internet slot) The one system with it's own IP is hooked up to the #2 slot in the hub and the other 2 shared connecting computers in the 1&2 Slots of the Router.
Now I am wondering one of 2 things: 1) IP is blocked for some reason from the cable company or 2) the Hub has gone bad. Cause if I unhook the the one system on its own IP and plug it into the #3 slot in the router it gains access to the net. If I unplug one of the system on the router and plug it into the hub I loose internet.
My 2 questions are pertaining to this thread is:
1) is there a way to tell if the hub is actually bad as it is about 5+ years old?
2) Is my wiring setup properly before I call the fricking cable company back and go round and round with them? Last time I battled them for like a total of 5 Hours on the phone and via live chat about the wiring and really don't want that headache again
Thanks much in advance for your help and expertise on these questions.
Much Appreciated.
Ron S.Just connect the computer with its own IP(i think it is static IP) directly to modem and see if it works, to test if IP address is blocked. Connect router to modem directly to check if modem gives IP address to router. If both work individually, hub might be the issue.
-
ASA5505 vlan routing with C2960
Hi, I need to have vlans on my C2960 routed using an ASA.
- Do I need to using VLAN interfaces or subinterfaces?
- Does the port connecting to the 2960 need to be trunked?
Here is the config I was planning on adding on the ASA:
#### CONFIG BEGIN ####
interface vlan 100
nameif outside
security-level 0
ip address 10.0.1.254 255.255.255.0
no shutdown
interface vlan 101
nameif mgmt
security-level 100
ip address 10.1.1.254 255.255.255.0
no shutdown
interface vlan 102
nameif ClassII
security-level 50
ip address 10.2.1.254 255.255.255.0
no shutdown
interface vlan 103
nameif ClassIII
security-level 50
ip address 10.3.1.254 255.255.255.0
no shutdown
interface vlan 104
nameif Acronis
security-level 50
ip address 10.4.1.254 255.255.255.0
no shutdown
interface vlan 105
nameif PreProd
security-level 50
ip address 10.5.1.254 255.255.255.0
no shutdown
interface ethernet 0/0
switchport access vlan 100
ip addr 70.X.X.X 255.255.X.X
no shutdown
interface ethernet 0/1
switchport mode trunk
switchport trunk allowed vlan 101-105
no shutdown
same-security-traffic permit inter-interface
#### CONFIG END ####
Also, if using same-security-traffic, can I still use access-lists to filter traffic between the vlans?
Thanks for the help.If you haven't seen this guide already, here:
http://www.cisco.com/en/US/docs/security/asa/asa72/configuration/guide/int5505.html
"Configuring Interfaces for the Cisco ASA 5505 Adaptive Security Appliance" -
Need Help with Linksys router broadband-b
I have a Linksys wireless-B broadband router for some reason it just went crazy on me. My wireless card is a wireless - G . Now when i had Verizon DSL i got this router and a USB wireless adaptor from verizon. I had the usb adaptor on my wife computer and the router and modem on my notebook for six months we had there dsl service until we moved to a nother city. Once we had all of our service's transfered to the new home we could not get verizon DSL there.
So for a nother six months we had to use dial up and being that we run a home business dial up was just not up to the task. Well we got rid of dish network just to get cable T.V. just to get the cable broadband service. That's when i got a wireless card for my notebook anyway for six months the network was working just fine with the router and my wireless card.
Until Sept this year just a few weeks ago the router started going crazy. Before my note book was config for windows to connect linksys was connecting and i would see all conection in the site survey, and my own network also. Until a few weeks a go my network would not show .
So i call linksys the have me download some up dated firmware that would not install on my notebook or my wife computer after being on the phone for hours with linksys they come to tell me that the router is ok and working alright after all the test and steps they took me through with the router. Linksys tells me that there is something wrong with my PCM slot on my notebook or either my linksys wireless card. Ok First of all i can pick up signal on other networks and go on line like the Hilton Hotel when i go in there parking lot, Second i can pick up othr networks and get on line that are not secured sometimes so this tells me that there is Nothing wrong with my PCMI slot or the wireless card.
Now i took my router across the street to a friend house and guess what he gets a signal off the router with his notebook but i can not and when we plug the router in the AC outlet the internet light was flashing like crazy and my wireless card was not even in my notebook so that tells me that someone close was pulling signal off my router but i cant.
Can someone please explain this to me i want to get another router wireless - G this time but if there is something that can be done to get this one working like it should that would really help.
The Notebook has been checked out and config and that works well when i hook the either net plug in from the modem the router was config as well but i just can't get a connected to the router when i use the wireless card.Yes press and hold the reset button in back for 30 seconds and release. Wait 10 seconds and power cycle the router. Now connect to 192.168.1.1 username blank, password 'admin'. Now try.
-
I am trying to connect a Windows 7 / 64 bit to an Epson printer on my Mac. The printer is hooked into the Mac via USB; the Mac is networked to a Linksys wireless router with an ethernet cable, as is the Windows box. I installed the current Bonjour printer services software on the Windows machine, and separately installed the driver software for the Epson printer on the WIndows machine. Running the bonjour wizard, I get an alert saying 'I don't have sufficient access to my computer to connect to the selected printer'.
The printer has 'sharing' turned on from the Mac end; this works with a Powerbook via the wireless connection. Sharing is also turned on in the Windows printer control panel for this printer (under properties). The Mac is a G5 running 10.5.8. When I try to print a page from the Windows machine it gets hung in the print queue.
Any advice how to proceed would be appreciated!
thx,I am trying to connect a Windows 7 / 64 bit to an Epson printer on my Mac. The printer is hooked into the Mac via USB; the Mac is networked to a Linksys wireless router with an ethernet cable, as is the Windows box. I installed the current Bonjour printer services software on the Windows machine, and separately installed the driver software for the Epson printer on the WIndows machine. Running the bonjour wizard, I get an alert saying 'I don't have sufficient access to my computer to connect to the selected printer'.
The printer has 'sharing' turned on from the Mac end; this works with a Powerbook via the wireless connection. Sharing is also turned on in the Windows printer control panel for this printer (under properties). The Mac is a G5 running 10.5.8. When I try to print a page from the Windows machine it gets hung in the print queue.
Any advice how to proceed would be appreciated!
thx, -
Having trouble setting up a linksys WRT54GS router with v...
Having trouble setting up a linksys WRT54GS router with verizon DSL using a westell 6100F modem. the modem works fine by its self but the router will not connect to the internet when installed like the cd tells you to.
online help and phone help has been less than helpful, anyone have any Ideas?Ok I found " Installing the liksys wireless router with a westell 6100 modem" in the verizon troubleshooting guides. printed the instructions so I would'nt forget. step 1 open your web browser and enter http://192.168.1.1 in the address field. PROBLEM it comes up with a login screen that I don't know how to sign into. tried the obvious stuff. cannot get past the login screen. I knew this sounded to easy to be true. anyone have any ideas?
-
Using linksys wired router with AE 2nd generation
Hi. I'm trying to use a linksys befsr41 (non-wireless 4 port router) with a 2nd generation airport express. I have several wired rooms that I want to setup separate networks with other AE's. My configuration is: cable box-->AE WAN in--AE LAN out-->Linksys-->ethernet cable through the house—>AE WAN in rooms. Can’t seem to make this work. I can do it wirelessly (i.e having the remote AE's joing the first AE network) but several of the rooms have poor signal. As soon as I try and create a new network the remote AE’s can’t connect to the network. I checked the cables and they are all good.
Thanks.We need some additional information to be able to troubleshoot this issue.
Can you provide the make and model number of the cable modem that you are using?
Are the other AirPort Express devices that you are trying to connect also 2nd Gen versions? If not, what version are they?
The Linksys router needs to be configured to operate in Bridge Mode so that it will function as if it were an Ethernet switch.....not a router. Is the Linksys set up in Bridge Mode at the current time?
Looking at the Linksys support forum....example below......I cannot tell whether it is possible to configure the Linksys product in Bridge Mode:
https://community.linksys.com/t5/Wired-Routers/Use-BEFSR41-in-Bridged-Mode/td-p/ 272061
Are you trying to configure the AirPorts using AirPort Utility on a Mac....or on an iPhone / iPad? If you are using a Mac, what operating system is the Mac running? If you are not sure, click the Apple icon in the upper left corner of the screen, then click About This Mac. Post back with the OS X version that you see there. -
Using Linksys router with Time Capsule / Airtunes...
Hi,
Does anyone have any idea how I can use my old Linksys WRT54G wireless router with my Time Capsule in such a way that the WRT54G provides a b/g network and I can have my Time Capsule provide just 802.11n for the best possible speed?
I have the two connected via Ethernet (TC connected directly to my cable modem) but don't seem to be able to get things to work.
I know I must be on the edge of getting this to work but am obviously missing the final step...
Cheers in advance for any help you can give,
Adi :o)go to this link:
http://discussions.apple.com/thread.jspa?messageID=6831703#6831703
than the link at the bottom of the page.
i just set this up this weekend - everything works perfectly. -
ACE design with inter-Vlan routing
Hello all.
I'm working on a design for a customer where the ACE will perform inter vlan routing.
A few questions about that :
- is routed traffic enforced in hardware with some kind of CEF-like mechanism ? (I suppose yes because there is a FIB ? per
https://supportforums.cisco.com/docs/DOC-19253 ) we expect a certain load and routing is software will not be acceptable
- if I put my VIPs within the VLANs hosting the application, is there any restriction on accesses made to this VIP (if the VIP is reached after the routing process is performed) ?
example :
VLAN2 (client) ----- ACE ----- VLAN3 (servers)192.168.2.0/24 192.168.3.0/24
If I try to access the VIP (192.168.3.20) from a PC in the VLAN2 (192.168.2.15) does it work ?
I assume yes because the VIP appears as a connected /32 in the routing table, I just want to be sure to not fall into some tricky part of code because the access to the VIP is done after the routing process. I just want to be sure there is no drawback / restriction about that.
Thanks in advance.Hello Surya!
Yes this is possible. You can reach the VIP from one VLAN to another (The VIP is not really inside of the VLAN). Important is to check your ACLs and you need to have the service-policy either globally or local on both VLAN-interfaces.
And I guess there is nothing like CEF implemented in the ACE, because it is not needed there.
Cheers,
Marko -
How apply cgi on Linksys router with safari
I'm having issues of setting preferences on a Linksys router with Safari and a Mac. Am I missing a setting on Safari to allow cgi?
I want to set how many users allowed on my small local network. I can use a different browser to accomplish this but would like to use Safari. From time to time I do maintenance on the router and need to access the router preferences. Also at this time trying to trouble shoot the router for not allowing PC's to show up on the network FInder, a completely different problem and off topic.
-
Using Airport Extreme with Linksys Router/Modem
I was just told that my Mac mini is excruiatingly slow on the internet because I am using a Linksys router with Xfinity and that Airport Extreme will be much faster. And that I should plug Airport Extreme into the modem. When I checked, I don't have a separate modem. My Linksys is a combined router/modem. What should I do? Do I plug the Airport Extreme into the Linksys box, or do I get a completely different modem that is only a modem? And, if I plug Airport Extreme into the Linksys box, how do I configure the network for Airport Extreme, and what else do I need to do? All help greatlly appreciated...I can barely get onto the Apple website!
When I signed up with Xfinity one of the stipulations was that they would not install a router/modem but only a modem. I had heard of problems with their router/modem and I didn't want to go down that path.
I don't but you mighht be able to get them to change out your router/modem for a modem. I would start there by asking them.
Allan -
Outlook send issues with Linksys router
I am on my brother's Linksys router with my own laptop. I can't send email from Outlook 2007, but I can receive it. Any ideas?
Make sure that under Outlook send receive settings ..... the Outgoing Mail Server ... should be in the form of .... mail.Domainname.xyz .... the same as in Incoming Mail Server ....
Click on More Settings and select the Outgoing Server Tab....
Check My outgoing server (SMTP) requires authentication......
Use same settings as my incoming mail server.....
Click Ok. Click Next. Click Finish
See if the Outgoing Mail is working or not ....
Maybe you are looking for
-
Illustrator CS5.1 Crashing on Start Up
Illustrator just started crashing on me. I have no idea what is causing it. It was working fine earlier today and then I restarted my computer, booted up the program, and after it went through the startup process and displayed the tool bars and men
-
I downloaded the latest version of itunes. I am now getting the message that my ipod is in recovery and needs to be restored. When I click to restore, it says it does not recognize this device. Now my ipod is frozen with an image of a cord and an
-
PDF Output Not Displaying Turkish Characters
Hi, We've configured BI 7.0 System with an Standalone Portal+BI Java System running both on SP11 Stack without problem. For BI Web Reports, we're taking PDF Outputs and getting Turkish Character Problems. On the screen we can see everything correct,
-
Attaching a document from program running in batch
Hi experts, i need to find a way, to attach a document (e. G. a CV) to an applicant via object services. Problem is, the document will be provided by a program, running in batch-mode without front-end access. I tried to debug the manual action, but u
-
Which SCs are needed if I want to use KM related API in webdynpro
Hi Gurus, I am using NWDI based development, i want to using KM api in webdynpro application. in the application, file will be uploaded using webdynpro fileupload component and stored in KM. I have read some tutorial and known which jars are needs. b