VMM 2008 R2 error 2921
When attempting to
converts windows 2000 with SP4 physical machine to VM using VMM 2008 R2. I
receive this error. I am login domain admin account and make sure the account
has right on the folder. Why I get this message?
Error (2921)
VMM cannot complete the operation on the file
C:\Users\administrator.PAYROLL\AppData\Local\Temp\SCVMM.1fca7033e3\boot.wim on
the hsamgmtsvr01.hsapayroll.com server. One of the following system errors
occurred: a file is read-only, the specified path is a directory, or Virtual
Machine Manager does not have the required permissions.
Recommended Action
Ensure that the path is valid and VMM has the appropriate rights to perform
this action.<o:p></o:p>
Bob Lin, MCSE & CNE Networking, Internet, Routing, VPN Networking, Internet, Routing, VPN Troubleshooting on http://www.ChicagoTech.net How to Install and Configure Windows, VMware, Virtualization and Cisco on http://www.HowToNetworking.com
Hi Sir,
Please try to add VMM Service account to Local System admin account of source computer .
Best Regards,
Elton Ji
Please remember to mark the replies as answers if they help and unmark them if they provide no help. If you have feedback for TechNet Subscriber Support, contact [email protected] .
Similar Messages
-
Hi,
I receive errors 2915 in VMM 2008 R2 SP1 while VMM tries to Refresh Host:
Error (2915)
The WS-Management service cannot process the request. Object not found on the host1.domain.lab server.
(Unknown error (0x80338000))
Recommended Action
Ensure that the agent is installed and running. If the error persists, reboot omicron3.jg2.local and then try the operation again.
My Hyper-V host: Windows 2008 R2 SP1 on HP DL380p G8.
I have tried solution from: http://support.microsoft.com/kb/976640 but with no luck. Could you help me with this problem?Any help will be appreciated.
-
Can I add windows 2012 R2 host to VMM 2008 R2?
We are running VMM 2008 R2 on Windows 2008 R2. When attempting to add a Windows 2012 R2 as host to VMM, I receive this message:
Error (2915)
The WS-Management service cannot process the request. Object not found on the mdnjdqgxd2.xxxx server.
(Unknown error (0x80338000))
Can I add windows 2012 R2 host to VMM 2008 R2? If yes, what could be the problem?
Bob Lin, MCSE & CNE Networking, Internet, Routing, VPN Networking, Internet, Routing, VPN Troubleshooting on http://www.ChicagoTech.net How to Install and Configure Windows, VMware, Virtualization and Cisco on http://www.HowToNetworking.comThe VMM Server should never have the Hyper-V Role enabled.
The VMM 2008 can only be installed on 2012:
http://technet.microsoft.com/en-us/library/gg610562.aspx#BKMK_SupportedOS
You need to look at the support matrix of the SCVMM version and the Hyper-V Server Version.
http://technet.microsoft.com/en-us/library/gg610649.aspx
In this case it is beyond 'support' it is what actually will work.
Brian Ehlert
http://ITProctology.blogspot.com
Learn. Apply. Repeat.
Disclaimer: Attempting change is of your own free will. -
Hi All
Please help
my server not working showing display error window server 2008 r2 error show "stop :- c00002e3 security account manager initialization failed because of the for A DIVICE ATTACHED to the system is not funcation"
Please help me how to resolve this issue ???
thnaks !!!Hi,
If there is any external device plug into your computer, please unplug it and restart the Server.
You can also test the issue in Safe mode.
If it can boot into Safe mode, please update any driver has yellow warning on it, also check if the dump file is existing under %SystemRoot%\, if so, please help to post back for our research.
Kate Li
TechNet Community Support -
Copy Templates from VMM 2008 to VMM 2012 R2
Hi,
I would like to know if it was possible to copy Templates from VMM 2008 to VMM 2012 R2 ?
Thank youI have never tried this, but you can for sure re-use the physical objects like VHD's, ISO's etc.
The template configuration and profiles are metadata stored in the database.
Based on how things changed with VMM 2012 compared with 2008, you will have several new options and capabilites in the profiles for 2012.
I would recommend you to re-create those (hardware profiles, guest os profiles, application profiles etc) in 2012, as there is no logical mapping from the previous versions.
-kn
Kristian (Virtualization and some coffee: http://kristiannese.blogspot.com ) -
Adobe CS3 - Server 2008 Install Error
I am in the process of transitioning our organization to a cloud server running Windows Server 2008 x64. I would like to be able to install Creative Suite 3 Design Premium on the new server. I have attempted the install but get the following error at the beginning before the installation will ever really get started "Critical errors were found in setup. Please see the setup log for details". Therefore, I am not able to even start the install.
I have tried for several hours to research on the web but have not found any definite answer. It does appear that CS3 is not supported by Adobe on Server 2008. Has any one had any luck getting it to install properly on Server 2008? If not CS3, will any of the newer version work on Server 2008 should I choose to upgrade to a newer Adobe product?
Thank you in advance for any assistance that might be provided. I greatly appreciate it.
ToddThank you very much for your assistance. I really appreciate it.
Todd
Mylenium <[email protected]> wrote:
Mylenium http://forums.adobe.com/people/Mylenium created the discussion
"Re: Adobe CS3 - Server 2008 Install Error"
To view the discussion, visit: http://forums.adobe.com/message/4115952#4115952 -
Estimate time usage for doing an P2V in VMM 2008 R2
Hi
Is it possible to get a estimated time usage for doing a P2V in VMM 2008 R2?
Maybe a preliminary scan or something?
Lasse
/LasseSadly no answers :-)
As far as I can see it's not possible to do a preliminary scan or something similar.
We did a P2V of a different server than the one in question which gave us an idea of the time needed.
Lasse
/Lasse -
Lots of Warning 1706 logged on VMM 2008 R2 Sp1
Hi,
I have VMM 2008 R2 Sp1 server with 3 Hyper-V hosts connected. In VM Manager event log I have noticed lots of 1706 warnings:
"Job <Id> (Refresh virtual machine) failed to complete".
Is it anything dangerous for my servers? Should I troubleshoot it?There are also "Job <Id> (Refresh host) failed to complete" 1706 warnings logged. Could anyone help me with this? How to troubleshoot this problem?
-
How to move VMM 2008 R2 Sp1 server to new machine
Hello,
I need to move/migrate VMM 2008 R2 Sp1 installation (server, not database) to new machine. New machine has several different roles installed so backup/restore method is not possible. New server will have different name.There are also several Hyper-V hosts
and library servers connected to old VMM.
Do you have any good step-by-step for this?
Robert Mandziarz | IT Administrator:
CodeTwo
If this post helps resolve your issue, please click the "Mark as Answer" or "Helpful" button at the top of this message. By marking a post as Answered, or Helpful you help others find the answer
faster.Hi,
Thank you for your posting in Windows Server Forum.
From your description it seems that you have 50 RDS User CAL, if I am wrong then please correct it. If you are using RD User CAL then you can track per User CAL and also generate a report by
RD Licensing Manager. But for tracking RD User CAL, the system must be domain joined as it won’t work with workgroup mode. After creating report you can have the CAL details and to retain\migrate and activate again you need to contact MS clearing house.
Please check below article for more information.
Track the Issuance of Remote Desktop Services Per User Client Access Licenses
http://technet.microsoft.com/en-us/library/cc754625.aspx
Migrate Remote Desktop Services Client Access Licenses (RDS CALs)
http://technet.microsoft.com/en-us/library/dd851844.aspx
Hope it helps!
Thanks,
Dharmesh -
Unable to install SQL Server Express 2008 R2 - Errors "Failed to retrieve data for this request"
As domain admin I am attempting to install "SQL Server 2008 R2 with SP2" but it keeps failing with "Failed to retrieve data for this request".
The installation never actually starts, it errors before then.
It displays the same error even if I run the System Configuration Checker.
The summary.txt for the install displays the following text:
Overall summary:
Final result: Failed: see details below
Exit code (Decimal): -1554760125
Exit facility code: 852
Exit error code: 15939
Exit message: Failed to retrieve data for this request.
Start time: 2014-08-15 16:49:52
End time: 2014-08-15 16:50:06
Requested action: RunRules
Machine Properties:
Machine name: servername
Machine processor count: 8
OS version: Windows Server 2008 R2
OS service pack: Service Pack 1
OS region: United States
OS language: English (United States)
OS architecture: x64
Process architecture: 64 Bit
OS clustered: Yes
Product features discovered:
Product Instance Instance ID
Feature Language
Edition Version Clustered
Package properties:
Description: SQL Server Database Services 2008 R2
ProductName: SQL Server 2008 R2
Type: RTM
Version: 10
SPLevel: 1
Installation location: c:\84122ef5b6d9cdcd3b2ac48cec\x64\setup\
Installation edition: EXPRESS
User Input Settings:
ACTION: RunRules
CONFIGURATIONFILE:
ENU: True
FARMACCOUNT: <empty>
FARMADMINPORT: 0
FARMPASSWORD: *****
FEATURES:
HELP: False
INDICATEPROGRESS: False
INSTANCENAME: <empty>
PASSPHRASE: *****
QUIET: False
QUIETSIMPLE: False
RULES: GLOBALRULES,SqlUnsupportedProductBlocker,PerfMonCounterNotCorruptedCheck,Bids2008InstalledCheck,BlockInstallSxS,AclPermissionsFacet,FacetDomainControllerCheck,SSMS_IsInternetConnected,FacetWOW64PlatformCheck,FacetPowerShellCheck
UIMODE: AutoAdvance
X86: False
Configuration file: C:\Program Files\Microsoft SQL Server\100\Setup Bootstrap\Log\20140815_164944\ConfigurationFile.ini
Detailed results:
Rules with failures:
Global rules:
There are no scenario-specific rules.
Rules report file: The rule result report file is not available.
Exception summary:
The following is an exception stack listing the exceptions in outermost to innermost order
Inner exceptions are being indented
Exception type: Microsoft.SqlServer.Management.Sdk.Sfc.EnumeratorException
Message:
Failed to retrieve data for this request.
Data:
HelpLink.ProdName = Microsoft SQL Server
HelpLink.BaseHelpUrl = http://go.microsoft.com/fwlink
HelpLink.LinkId = 20476
DisableWatson = true
Stack:
at Microsoft.SqlServer.Management.Sdk.Sfc.Enumerator.Process(Object connectionInfo, Request request)
at Microsoft.SqlServer.Chainer.Infrastructure.SqlDiscoveryDatastoreInterface.ProcessDTbl(DataTable dt, Int32 level)
at Microsoft.SqlServer.Chainer.Infrastructure.SqlDiscoveryDatastoreInterface.CollectSqlDiscoveryData(String machineName)
at Microsoft.SqlServer.Chainer.Infrastructure.SqlDiscoveryDatastoreInterface.LoadData(IEnumerable`1 machineNames, String discoveryDocRootPath, String clusterDiscoveryDocRootPath)
at Microsoft.SqlServer.Configuration.SetupExtension.RunDiscoveryAction.ExecuteAction(String actionId)
at Microsoft.SqlServer.Chainer.Infrastructure.Action.Execute(String actionId, TextWriter errorStream)
at Microsoft.SqlServer.Setup.Chainer.Workflow.ActionInvocation.ExecuteActionHelper(TextWriter statusStream, ISequencedAction actionToRun)
Inner exception type: Microsoft.SqlServer.Configuration.Sco.SqlRegistryException
Message:
The network path was not found.
Data:
WatsonData = [email protected]rror
Stack:
at Microsoft.SqlServer.Configuration.Sco.SqlRegistry.CreateBaseKey(ServiceContainer ctx, String machineName, IntPtr hKey, String keyName, RegistryAccess access, RegistryView
view)
at Microsoft.SqlServer.Configuration.Sco.SqlRegistry.GetLocalMachine(ServiceContainer ctx, String machineName, RegistryAccess access, RegistryView view)
at Microsoft.SqlServer.Discovery.DiscoveryEnumObject.GetSql2kMsiInstanceListInHive(String machineName, RegistryView regView)
at Microsoft.SqlServer.Discovery.DiscoveryEnumObject.LoadSql2kInstanceList(String machineName)
at Microsoft.SqlServer.Discovery.Product.GetData(EnumResult erParent)
at Microsoft.SqlServer.Management.Sdk.Sfc.Environment.GetData()
at Microsoft.SqlServer.Management.Sdk.Sfc.Enumerator.GetData(Object connectionInfo, Request request)
at Microsoft.SqlServer.Management.Sdk.Sfc.Enumerator.Process(Object connectionInfo, Request request)Inner exception type: Microsoft.SqlServer.Configuration.Sco.SqlRegistryException
Message:
The network path was not found.
Data:
WatsonData = [email protected]rror
Above message says that your registry is not consistent and some of the parameters are missing from registry.Or
Account installing SQL server does not have permission to access this. I think case can be here that account with which you logged into your system to install SQL Server might not have certain privileges. Can you take help
of domain admin account add it as a local administrator in this machine always right click on setup file and select run as administrator. Before this make sure you remove all SQL Server components from add remove program
I strongly recommend you to have a good look at below thread
http://support.microsoft.com/kb/2000257/en-us
Please mark this reply as answer if it solved your issue or vote as helpful if it helped so that other forum members can benefit from it.
My TechNet Wiki Articles -
Crystal Reports 2008-Vista-ERROR-crw32.exe Entry Point Not Found in dll
Hi Experts,
I just installed the Crystal Reports 2008 (with SP0) on my Vista (Home) machine. When I try to start the CR 2008, I am getting the below error message:
Error Title: crw32.exe - Entry Point Not Found
Error Message: The procedure entry point ?PrintLegend@CMapXLegend@CSLib300@@QAEXJJJJJ@Z could not be located in the dynamic link library cslibu-3-0.dll
Here are the things I tried to resolve the above problem:
1) Uninstall and Reinstall the CR 2008. - No change.
2) I configured the DEP to accept Crystal Reports (Performance - Advanced - DEP allow).
None of these seem fix the problem.
Can you please help me kick start the Crystal Reports 2008?
Thanks,
ArunPlease try with this:
Run a command prompt as administrator. From the start menu, select "All Programs", then "Accessories" and right-click on the "Command Prompt" shortcut and choose "Run As Administrator". From here you can use the following command to disable Data Execution Prevention (DEP) with the following command:
bcdedit.exe /set nx AlwaysOff
Keeping your command prompt open, run your setup or other process being stopped by DEP. Then, to turn it back on again, do the same and run the following:
bcdedit.exe /set nx AlwaysOn
Regards,
Shweta -
Ssrs 2008 r2 error-Forward pointing dependencies are not valid
In an existing SSRS 2008 r2, report, I am attempting to add a parameter called 'Customer_Category'. I am getting the following error message:
The report paramter 'CustomerNumber' has a DefaultValue or a ValidVaue that depends on the report parameter 'Customer_Category'. Forward pointing dependencies are not valid.
I am trying to determine how to fix this error. The 'CustomerNumber' is a parameter value that is obtained by reading from a dataset. In this dataset there are existing other parameters called 'Customer_Type' and 'Customer_Preference'. Both of these parameters
obtain there values from selections that the user makes when the SSRS report is executing. There are no default values.
I am trying to have the 'Customer_Category' be the same way where there are no default values and the user must select the parameter value when the report is executing. There should only be one value that the user can select from.
The new parameter called 'Customer_Category' is the last parameter in the list of parameters. Does the order of parameters make a difference? If so, how can I move the 'Customer_Category' parameter in front of the customer_number parameter?
Here is the sql that is used from obtaining a list of customers from the dataset for customer_number:
SELECT Distinct CustomerNumber
FROM BridgeUserCustomer
WHERE
Type = @Customer_Type
AND Preference = @Customer_Preference and Category = @Customer_Category
GROUP BY CustomerNumber
Would you tell me what is wrong and what I can do to solve the problem?Create independent datasets for each parameter and try once.
Regards, RSingh -
Hello,
Development Server
Recently, I have upgraded SQL Server 2008 Reporting Services (Integrated Mode) with SQL server 2008 R2 (Enterprise version). This reporting services configured with Share Point 2007 (MOSS) farm. Successfully upgraded the SQL 2k8 R2( Microsoft SQL Server
Reporting Services Version 10.50.1600.1 ). Before upgrade i can able to run report without any error but after upgrade when i tried to deploy report, report deployed fine, but when i tried to run report i got following error.
An error occurred during client rendering.
Unsupported RPL stream version detected: 34.62.1836345404. Expected version: 10.3.
I can run report successfully directly from the RS server without going from Share point site.
http://Has1de01/<report name>
Configuration Topology
Moss 2007 Application Server
WFE server 1 (MOSS 2007)
WFE server 1 (MOSS 2007)
Reporting Server 2008 R2 with RS add ins 2008 ( Just upgraded only this server, RS add-ins not upgraded)
Problem/Questions
Report is not working after upgrade, old reports nor new reports, why?
Report is working directly from RS server without going to Share point, so do i need to upgrade the RS add-ins OR am i missing something?
Can Share Point MOSS 2007 work with SQL server 2008 R2 OR do we need Share Point 2010?
If you need more information about Topology, please let me know . Please help me out. I also need to upgrade my Production server too.
RS log
Library!ReportServer_0-6!84c!05/26/2010-10:19:30:: Call to GetSystemPropertiesAction().
library!ReportServer_0-6!84c!05/26/2010-10:19:30:: Call to GetPermissionsAction(http://server.com/reporting/DataSources/TestReport.rdl).
library!ReportServer_0-6!84c!05/26/2010-10:19:32:: Call to GetItemTypeAction(http://server.com/reporting/DataSources/TestReport.rdl).
library!ReportServer_0-6!84c!05/26/2010-10:19:32:: i INFO: RenderForNewSession('http://server.com/reporting/DataSources/TestReport.rdl')
webserver!ReportServer_0-6!84c!05/26/2010-10:19:35:: i INFO: Processed report.
Report='http://server.com/reporting/DataSources/TestReport.rdl', Stream=''
Looks like Srtream is empty
Regards,
MitHi,
I have
the same
problem
and I think it
is any component
of
office,
any of
you found
the
solution? -
Hello,
We've installed SQL Server 2008 and Reporting Services 2008 on a Windows Server 2008 Enterprise box. I could initially access the Report Server at the default URL, but when I attempted to access the Report Manager, I got a 500 Internal Server Error message. When I looked in the RS logs I found the following:
ui!ReportManager_0-2!a34!01/30/2009-11:08:40:: e ERROR: This implementation is not part of the Windows Platform FIPS validated cryptographic algorithms.
ui!ReportManager_0-2!a34!01/30/2009-11:08:40:: e ERROR: HTTP Status Code --> 500
-------Details-------
System.InvalidOperationException: This implementation is not part of the Windows Platform FIPS validated cryptographic algorithms.
at System.Security.Cryptography.RijndaelManaged..ctor()
Once I disabled FIPS compliancy on the server, the issue disappeared and I had full access to the Report Manager. Unfortunately, for this particular project, FIPS compliancy is required, so I need a way to run the manager with FIPS enabled.
I've looked into this elsewhere and found out that a fix was released for the same issue in SQL Server 2005 Reporting Services. Is there a fix or workaround for 2008 yet? Has anyone else come across this problem?
Thanks in advance for any suggestions.
RLGHi RLG,
To work around this problem, change the configuration in the Report Manager Web.config file. Specify that ASP.NET use the Triple Data Encryption Standard (3DES) algorithm to process view state data. To do this, follow these steps:
In a text editor such as Notepad, open the Report Manager Web.config file which is located in the default path: <driver>:\Program Files\Microsoft SQL Server\MSRS10.MSSQLSERVER\Reporting Services\ReportManager.
In the Web.config file, locate the <system.web> section.
Add the following <machineKey> section to in the <system.web> section:
<machineKey validationKey="AutoGenerate,IsolateApps" decryptionKey="AutoGenerate,IsolateApps" validation="3DES" decryption="3DES"/>
Save the Web.config file.
If you have any more questions, please let me know.
Thanks.
***Xiao Min Tan***Microsoft Online Community*** -
I have several Windows Server 2012 R2 hosts. The OS is freshly installed, no roles/3d party software besides Hyper-V role). I also have a freshly installed VMM 2012 R2 server. They all are in the same AD domain. I want to manage those Hyper-V hosts
with this VMM instance, but I have troubles connecting those hosts to VMM.
Whenever I try to add a Hyper-V host in the VMM console, the process is stopped almost immediately after it starts. The failing step is "1.2 Install Virtual Machine Manager Agent". The final error message is as follows:
Error (410)
Agent installation failed on XXX.
Incorrect function (0x80070001)
Recommended Action
Try the operation again. If the problem persists, install the agent locally and then add the managed computer.
If I try to install the agent manually copied from the VMM host (C:\Program Files\Microsoft System Center 2012 R2\Virtual Machine Manager\agents\amd64\3.2.7634.0
as of now) by just clicking on its MSI file in Windows Explorer (and agreeing to the Windows prompt to run it with elevated privileges), the installation fails as well with "Installation success or error status: 1603." in the
server Application log.
The only way I found to install the agent is to run the installation from command prompt with elevated privileges. In this case the installation finishes successfully, and I can add the host to VMM by marking the "Reassociate the host" checkbox
in the VMM wizard.
Why is it so? Isn't the agent supposed to install without manual intervention? As I recall, I had no such problem with previous versions of Windows Server and VMM.
Evgeniy Lotosh
MSCE: Server infractructire, MCSE: MessagingI brought up the share because it is off by default with Hyper-V Server as well as a Core installation. Regardless of the Firewall policy involved.
Maybe, but I don't work with pure Hyper-V and Core servers. I have a full-fledged Windows Server 2012 R2 Datacenter.
You're correct that File Server role is not enabled by default, this is my mistake. I open SMB-IN port manually (with the help of a group policy), and Windows considers it to be am equivalent of the enabled File Server role. Nonetheless, ADMIN$ share is
always accessible in my environment (and without it, for example, I wouldn't be able to remotely install things like SCOM Agent which installs without a glitch). Just in case I manually installed the File Server role, and it didn't help.
What you say about multihomed servers is interesting. The servers in question do have multiple network interfaces, but at the time I tried to install the VMM Agent only one of them (a designated host management / network access interface) had a real IP address.
Two other interfaces were non-configured (I apply a virtual switch configuration after the VMM Agent is installed). Just in case I disabled them when tried to install the VMM Agent remotely on the last host, and the installation still failed immediately
after start. Anyways, after the VMM Agent is installed manually the host can be normally re-associated with VMM, so it's doubtful that I have a network issue.
And, of course, there is no 3d-party software on the hosts (no antiviruses/firewalls in particular) except the EMC Unisphere Host Agent (a piece of software necessary for connecting a host to an EMC storage system) and networking drivers. Actually,
this is a pure Microsoft environment.
So I still believe that is has something to do with the Windows Installer inability to configure Windows Firewall policy after being invoked from Windows Explorer with a double-click on a MSI file. But I don't know how to strictly confirm it.
Evgeniy Lotosh
MSCE: Server infractructire, MCSE: Messaging
Maybe you are looking for
-
Playing a single album....and that's it!
Occaisionally, I want to play a single album and not have to listen to the songs that follow it in the music library. I want to have the experience of walking over to my old record collection, pulling down John Coltrane's A Love Supreme, putting it o
-
BW and R/3 in the same box with a single instance ECC 5.0
Hi anybody using this scenario of having bw and r/3 in the same box....we are planing to consider in our project. will be happy if anybody can provide me some help on this. thanks and regards neel
-
How to deal with the rejected stock if it is rjected by QC
Dear All, please let me know how to deal with the rejected stock from Quality point of view.i.e., for incoming materails and Finished if returned from customer Regards, P.Vijaya
-
The iOS 8.0.2 has been downloading for an hour on my iPad, is that normal?
The iOS 8.0.2 has been downloading for an hour on my iPad, is that normal?
-
Firfox 19.0.2 dont load pages properly
Most pages I open with Firefox give me a "Server cant be found" error message i.e Firefox can't find the server at www....I then have to hit the "try again" button (sometimes more than once) to get the page to load. Some pages when they do load does