WCS and WLC WLAN Config not fully in sync

Hi,
We're facing the issue WCS and WLC WLAN Config is not fully in sync. WLC  showing server 1 is IP:10.160.22.151, Port:1812 but WCS server showing none even  after click on “Audit” button. Any idea how to resolve this issue? Is this causing any wireless problem? Attached is screen captured. Thanks for your help.

You mentioned "audit". Have you done a WCS audit so the WLC and WCS are in SYNC?
If you make a change on the WLC you will not see it in WCS UNLESS they are SYNC. You will see the term "mismatch".
"Satisfaction does not come from knowing the solution, it comes from knowing why." - Rosalind Franklin
‎"I'm in a serious relationship with my Wi-Fi. You could say we have a connection."

Similar Messages

  • WCS and WLC AP values not fully in sync.

    I have recently added several new aps on my network,after they connect to the controller, I set a hostname, and change the ip address to a static. However, WCS still sees the aps by the old ip and host name despite going into each one, hitting audit, and then save, any way to fix this? Thanks.

    You may want to also consider the following:
    1) Both the WCS and the WLC need to be at the same major revs (i.e.: The if the WCS is at v4.2, then the WLC should also be at 4.2). Failure to do so results in some significantly bizarre behavior such as errors after an audit - at least that was my experience.
    2) You may have better success if you make the change from the WCS which pushes the change to the WLC and that way the WCS is already aware of the change. (Normally, this should work - I know of one instance where it does not: changing Master Controller Mode from the WCS).
    3) If you feel strongly about making the change in the WLC (and are running a newer version of code in the WCS/WLC - i.e.: 4.x), there is a setting that forces the WLC to send configuration changes to the WCS once APPLY and "Save Configuration" are clicked:
    From the *WCS*, click on Configure->Controllers and click on the controller you wish to change, and check the "Refresh on Save Config Trap" check box and click OK.
    This will cause the controller to push any configuration changes up to the WCS after an APPLY and "Save Configuration" are clicked.
    4) In terms of getting the WCS to actually synch up with the controller (assuming the WCS and WLC are at the same rev. levels), you may need to do what I did (this was subsequent to upgrading to v4.2 in both the WLC and WCS and having chronic "mismatch" status between the WCS and WLC):
    From the WCS:
    Configure->Controllers, check the controllers you wish to synch up. From the dropdown, select "refresh config from controller"
    Next, select the DELETE option (instead of the RETAIN option). I believe that there are bugs in the software that upgrades earlier revisions to 4.2. I know that it might seem undesirable to DELETE information in the WCS, however, if you choose "DELETE", it seems to get rid of the residual information from the previous revisions that did not upgrade properly and the WCS will now be in synch with the controllers. DELETING the other settings makes the audit errors go away.
    Subsequent audits may go better for you after performing the step shown above. However, you may need to repeat this process in item 4 above once or twice more until the database gets cleaned up, but after that my own experience has been that the WCS and WLC will eventually stay in synch.
    It is unfortunate that we are forced to come up with workarounds like these when the software should clearly be able to handle this on its own, but we do what we must to get the job done.
    Hope this helps,
    - John
    (Please rate helpful posts)

  • Rogue AP - Not in sync with WCS and WLC

    WCS - 7.0.164.0 and WLC - 7.0.98.0.
    For some reason, I am seeing rogue ap alert on WLC and am not seeing on WCS.   How do I clean up database and sync with WCS and WLC.
    I am seeing same thing with coverage holes.
    - Allen -

    Allen,
         On the WLC go to Management > SNMP > Trap Controls, make sure that you have the traps checked.
    HTH,
    Steve
    *Please remember to rate helpful posts*

  • WCS and WLC versions for Cisco 3600 WAP

    Hi,
    I got a few Cisco Aironet 3602i. The minimum WLC version to support these is 7.1.91.0. I am planning to upgrade to 7.2.103.0. The minimum WCS version to support these WAP is 7.0.220.0 and the next available 7.0.230.0. Checking the release notes for both of these WCS versions, there is no mention of support for WLC versions listed above.
    http://www.cisco.com/en/US/docs/wireless/wcs/release/notes/WCS_RN7_0_230.html#wp152663
    Am I missing something here ? What versions would be required on WCS and WLC to make all the three entities (WLC, WCS, WAP) inter-operable ?
    Thanks,
    Regards, Rashid.

    Thanks Scott.
    Table-5 from your link indicates WCS 7.0.230.0 support for WLC 7.1.91.0, although release notes for WCS fails to mention this. I think thats the only option in the our existing WCS based network then. Other option being to upgrade to NCS.
    The NCS page http://www.cisco.com/en/US/products/ps6305/index.html indicates it will be offered to existing WCS customers when releases. Would we be required to pay for the product or both product and licenses or none ?

  • Location Appliance 2700 - is it supported with v7 WCS and WLC?

    The compatibility matrix shows no support for a Location Appliance 2700 for any version 7.0.x.x for WCS and WLC. However, I did see a thread here where a v6.0.x.0 had compatibility. v6.0.202.0 is MD. Is it compatible with v7 WCS and WLC?
    Can any of the experts please comment? Thank you.

    Hi,
    here is the link that will answer ur question!!
    http://www.cisco.com/en/US/docs/wireless/controller/4400/tech_notes/Wireless_Software_Compatibility_Matrix.html#wp78062
    Please dont forget to rate the usefull posts!!
    Regards
    Surendra

  • WCS and WLC syncing

    Gday again,
    I am converting standalone cisco1231AP to LWAPP. In the process, the conversion is always successfull. Run the audit on WCS, refresh values from Controller and restore values from Controller... The process after that involves us running few lightweight templates. Now, with the newly converted AP, I used to be able to see thm on both WCS and WLC. However, I dont see the new APs in WLC anymore. Besides checking the SNMP settings for sync, what else should I check?
    Regards,

    are the APs registered to the WLC? whats the software running on the WLC and WCS??

  • Upgraded and Now TVAP will not fully install

    I upgraded my NB505 (Serial XXXXXXXXX to Windows 7 ultimate, 32 bit.
    I also installed an Atheros wireless Network Card with Bluetooth 4.0 (model AR5B225). Yes it has the BT capability as I know some Atheros cards with same model number do not come with the BT capability.
    I have tried everything I know (which is pretty good) yet when TVAP installs it refuses to load the Flashcards or FN functionality. I tried doing a custom install and that protionof the install is blacked out and not even available for install. I cannot force it to push it on. No Flashcards.
    So I installed the Flashcard utility v2.00.43 and the Flashcard installed and worked fine except I do not have ANY F8 functionality, no card or anything. All other FN keys display work as they are supposed to.
    My question then becomes, is this Atheros card not capable of accepting the FN-8 key combo? I find that hard to buy. The drivers, and I mean all drivers) are the latest and working according to WinBlows 7 Ultimate. End result, I cannot turn on the WIFI therefore I most likely cannot turn on the BT as well.
    I am running the latest TVAP software as reported on the specific netbook page. I double, no triple checked checked to make sure.
    The Atheros drivers are installed using latest version available (both BT and WLAN).  This is a perfectly clean build with nothing but WinBlows on it yet, as well as the TVAP program.
    After about 5 minutes, with the TVAP/Flashcards installed, the system fully locks requiring me to cold boot power off. No keyboard, mouse nothing. Full and total lock down. I boot back into SAFE mode and disable TVAP and the Flashcard Utility using msconfig. No further lockdowns.
    I uniunstalled all Toshiba software... decided to put in the original WLAN only card and low and behold WLAN came back and worked. Any ideas on proper driver or if this is even possible ot run this cardon a Toshiba Netbook/Satellite notebook.
    [Moderator edit to remove serial number.]

    mini notebook NB505-N500BL (PLL50U-01S008)
    Downloads here.
    The order of installation often matters. Install the basic Intel stuff, especially the chipset software and display driver, prior to any other drivers. Install the TVAP before any other Toshiba utility.
    If you change the hardware, all bets are off. Don't be surprised at any incompatibility. The device drivers are tailored to the hardware.
    If you haven't already, you should upgrade the memory from 1 to 2 GB.
    -Jerry

  • WCS and WLC, On the same VLAN ?

    Whats best practice ? Is it better to have the WCS on the same vlan as the controller(s)
    Johann Folkestad

    Given the fact that it is snmp traffic, the WCS to WLC snmp read/writes should be confined to a subnet(s) that are secured by ACLs/firewalls/rfc1918 address space, yada yada....
    One way to do it is to place the WCS behind a firewall on the same or reachable subnet as the WLC service or management ports. I prefer using the service port on the WLC for the WCS snmp traffic, this way I can prune that vlan off the switch trunk ports that the WLC connect to as well as put it in a subnet that is away from prying eyes. I have had it working just fine since 3.0.2x all the way up to the latest rev this way.
    the controller will touch an additional vlan for each dynamic interface you create for wlans
    You can also dual home the WCS server, but the default option on WCS install/upgrade is to bind to one interface (it will detect & prompt in regards to multiple interfaces - at least on the Linux version).
    Also don't forget to lock down https access to WCS web frontend as well

  • WCS and WLC Reporting

    Hello All,
    Does anyone know if there is a way to get the WCS or WLC to report if a change had been made via syslog or snmp?
    Also, is there anything specific that has to be configured in the WCS to send emails of traps or alarms? I see where there are places you can enter emails but I am not sure if that is all that is required for the WCS to send the report to that particular email address.
    Any configuration examples or details would be great.
    Thanks

    On the controller, the WLC can be setup to send messages to a syslog server you may need to specify on the GUI, the level of the messages you want sent for rogue detection, you may need to specify software errors. Also, via WCS, you can have it send emails on the rogue traps / messages. A 3rd method is to setup snmp if you have something like hp open view. the mibs are at the link below, depending upon which image you have.

  • HT1386 I just loaded the latest version of itunes and now my Outlook notes won't sync and notes no longer appears in the advanced section of the info page

    I just loaded the latest version of itunes and now I cannot sync my notes from Outlook 2010 to my iphone.  Notes no longer appears under the advanced section of the info tab.  Since I have not had luck syncing in the cloud I always check the boxes and tell the sync to sync from my computer to my phone.  Does anyone know how to get this to work.

    When you connect your ipod up to the computer. It should show the device, usually with the name of the device, in my case 'jordan's ipod'. This should be on the row which shows 'songs', 'albums' e.t.c on the far right. There when you click on it it should go to a different screen showing a picture of your ipod along with two buttons - Update and Restore. Click update and it should take a 2 mins while your ipod is updated to the latest version of Ios.
    After updating te ipod see if there is a change in results.
    PS: make sure the device is active while syncing so keep tapping the screen.
    Sorry for any incorrect info, i have an ipod touch, but i've had experience with an ipod

  • My ipod and iphone 4s will not erase or sync with my new computer.

    My phone was loaded from this computer when I got it replaced because the last one was defective.  They will not load, unload, or anything.  This is frustrating because before the most recent rounds of updates and "fixes," I never had problems and knew where everything was. 
    It is not a problem with my library being different, because I just moved the library over from my old computer to the new when I got it using my external hard drive and literally just took iTunes and the music, books, etc over at one time.
    Edit: Checking or unchecking the manual management of the library, full sync, and/or partial sync has no effect either.  When I work on trying to make them sync, the computer shows- under the "on this ipod" section- that there is nothing there, but the ipod/phone disagrees and still has everything.

    You can only sync with one computer. To switch syncing computers:
    Syncing to a "New" Computer or replacing a "crashed" Hard Drive: Apple Support Communities
    If all synced media like apps and music are already on the second computer then just backup the iPod to the second computer and restore from that backup
    iOS: Back up and restore your iOS device with iCloud or iTunes       

  • Acs 5.3 and wlc 2504 config with restricted network access

    Hello,
    i submit you the following issue that i'm actually facing:
    i must configure a secured wireless network with access restriction based on SSID. the equipements are : cisco wlc 2504 (soft 7.3) cisco secure acs aplliance 1121 (soft 5.4) .
    the users that will connect to the network are regrouped by identity groups, each identity group having it's own SSID. Clearly each group of users must access only one SSID.
    i followed the procedure below to configure it:
    -- creating user identity groups;
    -- creating users and assigning them to the groups;
    --- creating authorization profiles for each SSID under policy element/ authorization and permission/network access/authorization profiles and putting the Airespace-Wlan-Id(the SSID number) in the radius tab.
    --- assigning the authorization profiles to the identity groups under access policies.
    after all these config the users can access the network using there userid/password configured. But the problem is Every user can access every SSID, seems like the restriction is so not very well configured.
    i found some documentation on this kind of config but the version of ACS used seems older than the one that i use, so menu are very different.
    Please can someone provide with the right steps to follow to achieve this kind of config.
    tkx in advance

    Yes.. you only have to add the end filter like what I posted... as far as the calling station id in the WLC security tab, it doesn't matter because that is not used when using 802.1x.  I would also try to not enable everything that you have just to start from the basic and make sure it works first.  The WAP Authentication Method might or might not work for you.  Uncheck that for now and when you have a successful authentication, look at the monitor log and see what radius attributes are being sent, because those attributes is what you can use to build your policies.
    Thanks,
    Scott
    Help out other by using the rating system and marking answered questions as "Answered"

  • Wcs and wlc snmp

    if you configure a wireless controller to not send any client traps, does that affect client information and stats in wcs?  wcs is managing controllers, and the controllers are also configured to send traps to another third party trap receiver for ticketting.  since the 3rd party trap receiver is not using these client traps for anything, and there are thousands being sent, its putting unnecessary load in the trap receiver.  If I configure the controller to stop sending client traps (like associate/disassociate, etc..) will that affect the client information that wcs reports?              

    Hello,
    Good question. The answer is No.
    WCS would still poll the controller(s) through SNMP to get that information. From WCS, if you navigate under the Administration --> Background tasks page you would see the list of polling tasks there. The snmp traps help in getting the information quicker to the management application rather than waiting for the polling to happen (which could happen only for every 15 to 60 minutes depending on the task). So your Client reporting in WCS should have the data regardless of the TRAP configuration on the WLC's.
    Ram

  • License problem with WCS and WLC

    Hi All,
    I have planned to implement three WLCs and one WCS to manage them.
    AP count is as below :-
         WLC #1     -     10 AP
         WLC #2     -     10 AP
         WLC #3     -     20 AP
    When WLC #1 is down that connected 10 APs should failover to the WLC #3.
    So at normal scenarion, WLC #3 should need 30 AP license; to failover WLC#1 APs properly to the WLC #3
    My problem is, Can I load total AP license (40 license) to WCS without installing them to individual WLCs ?
    If it is possible i can cut off the additional 10 AP license, required to the HA and failover.
    or if I use a WCS may i need to buy additional 40 license to WCS seperately from 40 WLC license ?
    Thanks,
    Charith

    Yes, you required to have seperate licences for WLC & WCS.
    You cannot add WLC licence to WCS & vice versa.
    HTH
    Rasika

  • User admin authentication to WCS and WLC

    Hi Experts,
    Do you know is it possible to configure WLC and WCS management user access to authenticate to TACACs like IOS routers does.
    If its possible do you know where I can find a doco as a guide. Tried to find but to no avail.
    WLC
    Model No. AIR-WLC2106-K9
    Software Version 5.2.178.0
    WCS
    version 6.0.181.0
    ACS
    Cisco ACS 4.2
    Thanks
    Rgds
    Kumar Ramalingam

    I think you are looking for this for WCS
    http://www.cisco.com/en/US/docs/wireless/wcs/5.2/configuration/guide/5_2admin.html#wp1059589
    and the WLC guide is here.
    http://www.cisco.com/en/US/tech/tk722/tk809/technologies_tech_note09186a0080851f7c.shtml#topic6

Maybe you are looking for

  • Errors when using imagex on T500 Laptops

    Greetings, I've been using windows PE and imagex to deploy a standard image to my laptops and desktops which are running Windows Vista (I've used it for Dell Desktops and some T61 boxes).  I've successfully used sysprep to prepare the image (sysprep

  • Problem faced while creating database in oracle 10g

    SQL> get C:\Oracle_Docs\ex\dbcreation_script\DBCREATIONSCRIPT 1 create database db_test 2 logfile group 1 ('C:\oracle\product\10.1.0\oradata\orcl\testdb\REDO01.rdo','C:\oracle\product\10.1.0\oradata\orcl\testdb\REDO02.rdo') size 100 m, 3 group 2 ('C:

  • Arabic Fonts support (Oracle9i)

    Hi all. I'm working on an application and the client wants the output to be in arabic. So my question is whether arabic fonts are supported in Oracle 9i and how?

  • USB 3G cle and Mac book pro

    I cant get my orange fr 3G usb cle do work on my new mac book pro - it automatically downloaded on my friends mac but won't on mine

  • RFC function to return number of records in a table

    Hello, I am looking for a RFC function to return just the number of records in a SAP table. I don't want to use RFC_READ_TABLE since it takes too long when I query a big table. Any advices?