What are the output specs on the creative car and house charg

I found a belkin AC to USB adapter and here are the specs:
Belkin Model: USB-TC-0 Input: 00~240 VAC, .3A, 50~60Hz Output: 5.5 VDC, A Plugs into US standard wall socket Provides one powered USB port
Would this work?
What are the output specs of the creative car and house charger so i can compare it to this?
thanks

Justinw wrote:
is your charger a house one or a car one? thanks for you help.
not sure about the .5v difference
That would be for the house. And it should work with a .5V difference, but dont hold my word on it when your player gets hot. Also this is for a Zen Micro?

Similar Messages

  • What is the recommended number of clients per Mac server? Also what are some recommended specs when purchasing an Apple machine that will have Mac OS X server installed?

    What is the recommended number of clients per Mac server? Also what are some recommended specs when purchasing an Apple machine that will have Mac OS X server installed? We have around 300 clients that need to be enroled on the Mac server. I want to know what is the recommended amount of clients a Mac server should contain. Also what are some recommended specs to make sure the server will flawlessly?

    Hello cpreasbeck,
    Thank you for contacting Apple Support Communities.
    I was able to find the following transition guide for Xserve that provides some workload guidance to determine performance when planning a server deployment.
    Transition Guide Xserve
    http://images.apple.com/xserve/pdf/L422277A_Xserve_Guide.pdf
    On page 9, Performance there is a chart that provides maximum numbers of connected users for various activities such as file sharing, mail, web, calendar, directory services and Time Machine and the CPU used as a server (Xserve, Mac Pro, Mac Mini). This information is a bit dated as the referenced software is Snow Leopard Server (OS X 10.6), and the hardware is older also, but it should give you a general idea of what you might need to look for.
    Regards,
    Jeff D.

  • What are the full specs of the hard drives on Time Capsule?

    Does anyone know the full specs of the "server grade" hard drives of a 4th gen 2TB time capsule? thanks
    Dustin

    It is just the standard WD green drive.
    WD20EARS
    It is "server grade" purely in Apple's mind.
    http://www.anandtech.com/show/4577/airport-extreme-5th-gen-and-time-capsule-4th- gen-review-faster-wifi-/4
    Mind you I think you will find they do not stick to a single brand of drive. They might also be in the same trouble everyone else is in with HDD in short supply at the moment due to floods in Thailand.

  • My iPhone was stolen and I have contacted the police who are using the meid number to locate.  How does this work and what are my chances of getting the phone back?

    My iPhone was stolen.  I used Find My iPhone app to lock it and display a message.  The phone has not connected to the internet to locate it.  I contacted the police and they have taken my meid number.  How does this work and what are my chances of getting the phone back?  Are there other ways the theif can use it.  I was told once they put in a new sim card and use it, whatever software the police have, it will show up.

    Honestly? In the US (I can't speak to other countries, though I doubt it works much differently in a lot of the world) The police took your report and filed it either in their computers or, on paper. They will now not think of this again. The only time it will cross anyones mind is if, in the course of entering information into evidence about items recovered or seized at a crime scene, the serial number of an iPhone that was found/seized happens to match yours, in which case you will be contacted.
    The police in the US can and will do nothing to 'blok' the phone and it's not worth their time to try and locate it unless you know for a fact that it was stolen by a big time drug lord, master criminal, or some other such prime target and they can get a court order to track the location of the phone in order to locate this individual for your own purposes.  If they do that, they'll probably keep him under surveilance for a year or so before they act.
    Basically, the police don't care about your phone. If they find it, they will give it back to you. They are not, however, going to go looking for it. They have better things to do.
    I'm sorry, but that's the way it is.

  • What are options available to cancel the Excise Invoice?

    Hi,
    What are options available to cancel the Excise Invoice?
    Does cancelling the commercial invoice automatically cancels the excise invoice
    if not what are the other options?
    Any settings required to achieve that.
    Usefull answers will be rewarded
    Thanks
    Regards

    Dear Rajiv
    No cancelling commercial invoice will not cancel the excise invoice in background.  For that, you need to run the T.Code J1IH where if you click on Cancel Excise Invoice, system will ask for excise invoice reference, financial year and series group.  Here while giving the excise invoice number, you have to ensure that it is preceded with zeroes as you can see in J1I7.
    thanks
    G. Lakshmipathi

  • Just bought an IPod nano 7th generation.  I have a Mac computer OS X v10.5.8 with 10.6.7 iTunes player. To use the new IPod nano I need a OS X v10.6.8 or later and iTunes 10.7 or later. What are my options to upgrade the Mac?

    Just bought an IPod nano 7th generation.  I have a Mac computer OS X v10.5.8 with 10.6.7 iTunes player. To use the new IPod nano I need a OS X v10.6.8 or later and iTunes 10.7 or later. What are my options to upgrade the Mac? 
    Thanks to your feedback.

    Click here, check that your computer meets the requirements, purchase and install the DVD, and run Software Update.
    (74380)

  • How to view what are all programs maped with the event....

    I am new to this events concept - could you please say
    in SM64 we can give Event....
    <b>How to view what are all programs maped with the event..</b>
    Thanks in advance.

    Hi Sam,
    See these links:
    How-to trigger a process chain using ABAP?
    Re: scheduling process chain 3 specific times a day
    NOTE: If you want to trigger the process chain from R/3, there are many examples in this forum. However, since the search function is not working now, I suggest you look at OSS Note 135637. This will show you how to do it also.
    Hope this helps.
    concerning to sm64 ..
    Triggering events manually ...
    Events let you start background jobs when particular changes in the R/3 System take place. When an event occurs, the background processing system starts all jobs that were scheduled to wait for that event.
    example : JOB_OPEN to create a background job..
    When scheduling a background job, you can specify it to start "after event".
    If you do so, you'll have to create an event in SM62.
    If a job is scheduled after event event and you trigger the event with SM64, the job will start.
    Events can be raised by external systems in SAP by sending a command to a SAP application server. You can also raise event in any program using function mosule BP_EVENT_RAISE.
    Reward if helpful.
    Regards,
    Harini.S

  • Anyone get to know what's the output power of the audio system?

    Hi. It's there anyone could tell me what's the output power of the 2.1 audio system in this 24" LED display?? Thanks

    Gabi759,
    The output on the Audigy 2 ZS is Line Level. We no longer use amplification on the card as that can cause distortion and an overall loss of audio quality. You may want to look at either replacing your speakers (as few sound cards have amplification) or get a preamp for them to power them.
    Jeremy

  • Are the outputs (vallues) of the following queries equal?

    Are the outputs (values) of the following queries equal expained by Oracle?
    SQL> select to_char(sysdate+1/24,'yymmddhh24') from dual;
    TO_CHAR(
    09081513
    SQL> select to_char(sysdate, 'yymmddhh24miss') from dual;
    TO_CHAR(SYSD
    090815130000

    Than you for reply.
    I use it for partitioning the table automatically and automatically get the partition names and ranges (get from the SYSDATE).
    For example create a partition per hour:
    sqlCreate='ALTER TABLE message ADD PARTITION '||'p_message'||
    TO_CHAR(SYSDATE+1/24,'YYMMDDHH24')||' values less than (TO_DATE('
    ''||TO_CHAR(SYSDATE+2/24,'YY/MM/DD HH24')||''
    ',''YY/MM/DD HH24''))';Is the previous code correct?
    Please modify it.
    Thank you

  • Generated Pulse waveform is distorted when I deliver the signal to the output port in the DAQmx

    Problem: Generated Pulse waveform is distorted when I deliver the signal to the output port in the DAQmx.
    Environment: Windows XP sp3 (32bit), Visual Studio 2010 sp1, NI-Measurement Studio 2010
    Device: NI - DAQmx PCI 6251
     Analog Input: 1.00MS/s multi-channel (aggregate)
     Analog Output: 2 Channel 2.00MS/s
    Reference Example: AO_ContGenVoltageWfm_IntClk / AI_ContAcqVoltageSamples_IntClk
    Generated Pulse:
    1) AO0 = Square Waveform /0-5V / 8KHz / 0.5㎲/sample / sample 50% Duty
    2) AO1 = Square Waveform /0-5V / 8KHz / 0.5㎲/sample / (Reverse Image)
    Description: I’d like to deliver the waveform stream satisfied with specified constraints to the 2 channel output port in the DAQmx. To verify accuracy of the generated waveform, I did an electrical wiring from the Analog output channel (2 channels) to the Analog Input channel (2 channels) in DAQmx. As a result of this experiment, I could get a result which has signal distortion. Since the waveform has to satisfy with both high frequency (8KHz) and very short moment interval time (△t = 0.5㎲/sample) between samples, I cannot handle some parameters of the function in the referenced VC++ example. Following formulas shows an approach to deliver the generate pulse waveform to output port satisfied with constraints.
    Analog Output Channel
     Frequency = 8,000 cycles/sec (constraint)
     Sample per Buffer = 2,000,000 = 2*106 samples/buffer
     Cycles per Buffer = 80,000 cycles/buffer
     Sample per Channel = 1,000,000 = 1*106 samples/channel
     Sample Rate  = Frequency * (Sample per Buffer / Cycle per Buffer)
                              = 8,000 * (2*106 / 80,000) = 2*106 samples / sec
     △t  = 1 sec / 2*106 samples / sec
               = 0.5 * 10-6 sec/sample (constraint)
     Buffer Cycle  = Sample Rate / Sample per Channel
                              = (2*106 samples / sec) / (1*106 samples/channel)
                              = 2 channel / sec
    Analog Input Channel
    Sample per Channel = 1,000,000 = 1*106 samples/channel
     Sample Rate  = 1 MS/s * (2 Channel) = 5 * 105 Samples / Sec
    Program Code
    AO_ContGenVoltageWfm_IntClk / AI_ContAcqVoltageSamples_IntClk (VC++ Example)
    Result: The proposed approach was implemented in the experiment environment (VS2010, MStudio2010). As shown in Figure 1, we could get the unsatisfied result. Although I intended to make a ‘square’ pulse wave, the result looks like ‘trapezoid’ pulse wave (Figure.1). However, there is other result which was undertaken with different parameter condition. It looks like the square shape not the trapezoid shape.
    Please let me know what the conditions make the problem of signal distortion. (AO0 = Green line / AO1 = Red line)
    [Figure. 1] Frequency 8000 Hz / Cycle per Buffer = 8000 Result
    [Figure. 2] Frequency 1000 Hz / Cycle per Buffer = 1000 Result
    Questions: Please let me know following questions.
    1) Is it possible to deliver the generated pulse wave satisfied with constraints (f= 8KHz), △t = 0.5㎲/sample) to the output port without distortion using PXI 6251?
    (Is it possible to solve the problem, if I use the LabView or MAX?)
    2) Are there some mistakes in the proposed approach? (H/W or S/W program)
    3) What is the meaning of the Cycle per Buffer?, It could effect to the result?

    Hi Brett Burger,
    Thanks for your reply. For your information, I have set the sampling rate as 10000 as for the sound format, I have set the bits per sample as 16 bit, the rate as 11025 and the sound quality as mono. I tried using your method by changing the sampling rate as 8K but still my program encounter the same problem.
    I wish to also create a button that is able to generate a preformatted report that contains VI documentation, data the VI returns, and report properties, such as the author, company, and number of pages only when I click on the button.  I have created this in my program, but I am not sure why is it not working. Can you help troubleshoot my program. Or do you have any samples to provide me. Hope to hear from you soon.
    Many thanks.
    Regards,
    min
    Attachments:
    Heart Sounds1.vi ‏971 KB

  • Placed an image in a new Illustrator document.  Tried to change the Output Mode in the Output Dialog but could not select "Separations Mode".

    Placed a DCS2 document image in a new Illustrator document. 
    Tried to change the Output Mode in the Output Dialog but could not select "Separations Mode".

    I would check with the makers of ULTRASEPS.
    I never heard of it, just checked their website, I don't think they support Illustrator:
    What do I need to use UltraSeps?
    UltraSeps requires Adobe Photoshop version CS2 or higher on Windows and Macintosh.
    Its also 100% compatible with Photoshop Creative Cloud and Creative Cloud 2014.

  • Content generation [Error: Unable to access the output directory. The directory is not writable, so

    Content generation
    [Error: Unable to access the output directory. The directory is not writable, so the folio cannot be saved.]
    This means?
    This is fun BTW. Two days and two different silly errors applying themselves arbitrarily. Yesterday was the network, today its this.

    heres the fix i used for on a Mac
    1. While in the Finder, select the menu command Finder > Preferences.
    2. In the General panel, ensure the option "Connected Servers" is selected under the heading "Show these items on the desktop:", then close the preferences dialog box.
    3. Choose the menu command Finder > Hide Others.
    4. Close all open Finder windows to ensure you can see all items on your desktop.
    5. If you locate what appears to be a mounted volume with the name "Users", Control + Click on its icon and choose the contextual menu command Eject "Users".
    6.  Add or update your article(s).
    7.  Cross fingers
    8. If doesn't work ask for a refund

  • On the Apple webiste, I read that you must run OS 10.6.8 in order to sync the iPhone 5 with the computer. However, in the tech specs on the "Buy the iPhone now" email  I  received at my .me email address, it list the OS sytem needed as 10.5.8. Which is it

    On the Apple website, I read that you must run OS 10.6.8 in order to sync the iPhone 5 with the computer. However, in the tech specs on the "Buy the iPhone now" email I received at my .me email address, it listed the OS sytem needed as 10.5.8. Which is it?

    In Reply to all fellow Apple fans: It is great that someone found a work-around to the iTunes 11.4 no syncing problem. I think that is fine for the short term. And  I am really glad that we customers have a forum to share information and experiences regarding Apple's products. However, as someone here said, we are all customers; and posting a problem here "IN HOPES THAT APPLE READS THESE POSTS" is NOT a way to resolve this issue or any issue.
    PLEASE CONTACT APPLE: Apple Service Center: 1-800-275-2273   - Once you get a ticket number then and only then is this documented and then Apple can follow-through and alert the engineers who will fix this.
    The "CWA2" work-around band-aid does several things in addition to reverting back to iTunes 11.3.1. :
    1) It ensures that Apple continues to know nothing of the problem.
    2) It ensures that the faulty code that is within 11.4 remains there and is perpetuated into future versions.
    3) It ensures that YOU can never upgrade to future versions. (If the resident faulty code remains and perpetuates)
    So once you have reverted back to 11.3.1, the problem APPEARS to have gone away (FOR YOU) but you have not solved the problem.
    Again, respectfully,
    1) Sending feedback to apple (using the "Report Bugs To Apple" menu item in Safari will get the information to someone, somewhere and add it to the pile of issues, complaints, suggestions, etc.
    2) CALLING the Apple service/support Center at  1-800-275-2273 will put you in touch with a real APPLE person who will begin the process of documenting and forwarding this issue on to those who will fix it.
    and
    3) emailing Apple directly will make sure that they get the information.
    lets get this fixed !!!!!!!!!

  • How to use the Output clause for the updated statment

    How to use the output clause for the below update stament,
    DECLARE @MyTableVar table(
        sname int NOT NULL)
    update A set stat ='USED' 
    from (select top 1 * from #A 
    where stat='AVAILABLE' order by sno)A
    Output inserted.sname
    INTO @MyTableVar;
    SELECT sname
    FROM @MyTableVar;
    Here am getting one error incorrect syntax near Output
    i want to return the updated value from output clause

    see
    http://blogs.msdn.com/b/sqltips/archive/2005/06/13/output-clause.aspx
    Please Mark This As Answer if it solved your issue
    Please Vote This As Helpful if it helps to solve your issue
    Visakh
    My Wiki User Page
    My MSDN Page
    My Personal Blog
    My Facebook Page

  • Maintaining the Output type in the PO from Sales Order

    Hi experts,
    I have developed one application for Sales Order that..there is one link of Purchase order in the Sales order.if i click on PO in the sales order.it goes to me22n screen.if i will maintain the output type in the PO and Click on SAVE button.it gives some error like (No update of sales order 100001 from purchase
                                     order (error V1 275)).
    cud u help me to solve the above issue.its very urgent.
    is there any way to change to va02 to va03...when i am going  from va02 to me22n
    thanx in advance
    regards,
    hpp

    May be because when saving the PO, it's trying to update some sales order related data too and it's locked by you. Try using the save button in output type maintenance screen, or open the sales order in display mode and call ME22N and try maintaining the output type.
    or try using LEAVE TO TRANSACTION ME22N from VA02.
    Regards
    Sridhar
    Message was edited by:
            Sridhar K

Maybe you are looking for