What do I do when I get this Time Machine message? The backup disk image "/Volumes/Mark McConnell's Time Capsu/Mark's MacBook Pro.sparsebundle" is already in use.
What do I do when I get this Time Machine error message?
"The backup disk image “/Volumes/Mark McConnell's Time Capsu/Mark’s MacBook Pro.sparsebundle” is already in use."
Unplug your Time Capsule from power. Wait 10 seconds and then power it on again. When the light goes green try backing up again.
Similar Messages
-
What do I do when I get this message on my Time Machine? "The backup disk image “/Volumes/Data/Jeanne’s iMac.sparsebundle” is already in use."
See C12.
Time Machine Troubleshooting -
I keep getting this error when trying to backup time capsule with time machine. The backup disk image “/Volumes/Data-1/Dan’s iMac.sparsebundle” is already in use.
Make sure that no other Macs are backing up at the time.
Pull the power cable from the back of the Time Capsule
Count to ten
Plug the power cable back into the back of the Tme Capsule
Wait a few minutes, then try a backup again. -
I am getting this error when time machine tries to back up to a time capsule. "The backup disk image “/Volumes/JUDY ARCENEAUX's Time Capsu-1/JUDY ARCENEAUX’s MacBook Air.sparsebundle” is already in use." Same time capsule has worked in the past.
First, restart the computer and the Time Capsule. In most of the cases, this should solve the problem.
If it doesn't work, see > http://pondini.org/TM/C12.html -
I keep getting the message "The backup disk image “/Volumes/Donald Baker's Time Capsul/Donald Baker’s iMac.sparsebundle” could not be accessed (error -1). does anyone know what this means? My time capsule refuses to back up.
Time Capsule and Time Machine master guru Pondini has all the answers.
Check # C17 in his excellent support document Time Machine -- Troubleshooting.
http://Pondini.org/TM/Troubleshooting.html -
i am running 10.7.5 on an older MacBook and getting Time Machine error The backup disk image “/Volumes/Data/Kathy P’s MacBook.sparsebundle” is already in use. what do i do now?
See Pondini's TM FAQs, for starters.
-
Time Machine did not back up:
Time Machine Error; ("The backup disk image "/Volumes/Data/My MacBook Pro.sparsebundle" is already in use.")
How do I correct this issue?
Thanks!You need to be careful Bob.. people might take this literally.
Bob Timmons wrote:
How do I correct this issue?
Call the exterminator to get rid of the bugs in Lion and Mountain Lion.
https://discussions.apple.com/thread/5222487?tstart=0 -
When my time machine tries to backup to my time capsule I get the following message"The backup disk image “/Volumes/Data/Kent’s MacBook Pro.sparsebundle” is already in use. " What do I need to do to fix this?
Restart the Time Capsule.
-
My backup got interrupted and now when I try to backup I get the following message: The backup disk image “/Volumes/Data/Macintosh.sparsebundle” is already in use. What should I do so that I can start backing up again?
1. Restart your MBP and try the back up again. If this fails try step #2 below
2. Unplug your Time Capsule from the AC giving it thirty seconds or so to discharge, plug it back in and retry the back up again once you're back online.
3. if step #1 and #2 fails, go here:
http://pondini.org/TM/C12.html -
I keep getting this message: The backup disk image “/Volumes/Time Capsule/Coyner’s iMac.sparsebundle” is already in use. What should I do?
SeoulTom (Coyner)Make sure that no other Macs are backing up at the time
Pull the power cord from the back of the Time Capsule
Count to ten
Plug the power cord back into the Time Capsule
Wait a few minutes, then try a backup again
Check to make sure that you are running firmware 7.6.4 on the Time Capsule -
When I try to backup I get the error message.The backup disk image"/Volumes/Data/iMac.sparsebundle" could not be accessed(error-1) Any Ideas? it was working fine and i can't think of any changes I made to the system to affect this?
Start with the best resource available..... Time Machine --- Troubleshooting from Pondini, the wizard of all things Time Machine.
" . . . sparse bundle could not be accessed (error -1)" -
time machine: I get the following message: The backup disk image “/Volumes/Data-1/Clemens’s iMac.sparsebundle” is already in use - what to do? Where and how do I find that file and get rid of it?
I'm on Mountain Lion and have version 6.1 of AirPort utility so there is no button to "Disconnect All Users"and the only other option of "removing and re-selecting the drive via Time Machine Prefs" doesn't work either. So this will work.
Launch Airport Utility and select the TC "Edit" button, then select the Disks tab. Deselect "Enable File Sharing" and click "Update". The TC will reboot then follow the same procedure and reselect "Enable File Sharing" and click "Update". After TC reboots again you'll be up and running. Not the neatest way to do it but saves having to unplug the TC which risks disk damage and the whole procedure takes less than a minute.The "Enable File Sharing" button seems to have replaced the "Disconnect All Users" button but with the slight disadvantage that it reboots the TC which takes up additional time. -
I just brought a New Macbook Pro and was successful in transfering data from my old macbook. However when I try to back up to my time capsule I receive this message. "The backup disk image “/Volumes/Salvatore Totino's Time Cap/Lorraine’s MacBook Pro.spars
You may need to reset TM and start with a fresh full backup.
For the particular error see
http://pondini.org/TM/Troubleshooting.html -
how to fix this error message The backup disk image “/Volumes/AirPort Disk/FARES DEL VALLE’s iMac.sparsebundle” could not be accessed (error -1).
The troubleshooting C17 is the specific article.
http://pondini.org/TM/Troubleshooting.html
This is generally a Lion error.. and you will need 5.6 utility to get access to the disk area.
So download the real utility. Run it instead of v6 toy version.
http://support.apple.com/kb/DL1482
Go to the manual setup, disk page and click on disconnect all users.. that will unmount all users connected to the disk and allow it to start working. But there are a number of other issues that are possible cause. Pondini lists some of them. -
I constantly get the following error message: The backup disk image "/volumes/data/jameskehoe.sparsebundle" is already in use. This Time Machine/Time Capsul worked perfectly before I left on a four month trip. Upon returning to my domicle it will not backup and I get the mentioned error message. My wife's Mac Book Pro continues to backup normally but she did not accompany me on this trip so her computer has always remained in contact with the Time Machine. My computer is a MacBook running 10.7.5
Any help solving this problem and letting me once again backup my computer would be greatly appreciated.This question is asked several times every day.. it is a bug.
Look at the more like this column to the right..
Solution is pretty simple..
With the TC hard disk not running.. you can feel the vibration ..
pull out the power cord.. count to 10.. plug in the power cord.
If you still have the problem report back.. mostly 98% of cases that will fix it. -
I am receiving the following error on my time machine, does anyone know what it means? Error message = The backup disk image “/Volumes/Data/Richard’s MacBook Pro.sparsebundle” is already in use.
Please look over the right of this page under the heading of More Like This for multiple answers and solutions for this bug.
Maybe you are looking for
-
My ipod touch says that I am connected to the internet through the setting tab but when i try to get on the internet it says no connection. I tried new downloads and updats and connectioning to other wifi in variouse places and still no luck.
-
Multiple Recipients not Receiving Mail
I have sent an email to multiple bcc'd recipients. I have reduced the number of recipients to less than 100. The message appears in my Sent mail folder, but is not received by any of the recipients, nor do I get any server messages indicating incor
-
How can i update ios 7 to my iphone 4s???
How can i update ios 7 to my iphone 4s???
-
We have a program with several tabs, each of which has different graphs and displays. On one of the tabs is a histogram style bar graph. We've added annotations to each bar to label each bar with a particular identifier. The graphs are set to au
-
Applet won't initialize when testing Applet
I compiled my file with no errors, yet when I test the Applet it tells me that it can not initialize, can anyone help me. Thanks