What is the internal impedance of the NI ELVIS Function Generator?
Does anyone know the load impedance of the function generator? I'm wondering how much it may be tainting the results of Tau for my RC circuit. Thanks.
Impact -
With the NI ELVIS Function Generator, the output impedence is spec'ed
at 50 Ω guaranteed. You can find the block diagram from the
Function Generator on page A-6 and C-6 (Appendix C: Theory of
Operation) of the NI ELVIS User Manual.
NI Educational Laboratory Virtual Instrumentation Suite (NI ELVIS) User Manual - http://digital.ni.com/manuals.nsf/websearch/11E6BA4103D9ADD086257103005C97E0
Good luck with your application!
Mark Walters
Application Engineer
Similar Messages
-
I have a Lucid 2 LG. I have been having trouble with insuffient storage. I have a 8G phone and have spent hours with Tier 2 tech trying to move info from the internal storage to the SD card with no luck, When I go to storage in the settings it states that over 4 gigs is for Misc? System data takes up over 4 gigs. No one can tell me what system data consist of. So My question is does anyone know what system data is? I am assuming I have a 8 gigphone but can only use 4 gigs???
System data is the OS or operating system. That is where the recovery stays separated from the rest of the storage so that it doesn't get corrupted. It is not accessible and non-movable.
-
A shadowy glow on the internal top of the screen...
Hello ppl , i purchased a iphone5s a fortnight ago , I noticed a shadowy glow on the internal top of the screen when i tilted the phone... when to the service centre the service engineer couldnt repair it so i asked for a replacement as the other iphones do not have anything like the one i had ...he told me that he would talk with his higher authorities ... After a day i got a call from him saying that i would not get a replacement as his seniors said that it is within technical grounds they say that they cant replace it, they say only if i have a issue with the performance they are gonna think about it ..very much dissapointed with apple ...paying 53k and getting a defected phone is just unacceptable ...plz tell me what should i do ....
Where did you buy the phone originally?
-
How do you get Photos to recognize the “old” iPhoto Library on an external drive without it copying it to the internal drive on the computer which is low in HD space?
Launch Photos while holding down the alt/options key.
This will show the Library Chooser panel. Select the library on the external drive. Photos will create a Photos Library on the same drive.
Photos may not be able to open the library, however, if your external drive has an incompatible file system. It needs to be formatted MacOS Extended (Journaled) and locally mounted, not a remotely mounted volume, as described here: Format external drives to Mac OS Extended before using with Aperture -
DCIM folder is not available in the internal storage, and the internal storage folder shows it`s empty
Pls help me in resolving the issueDCIM folder is not available in the internal storage, and the internal storage folder shows it`s empty
Pls help me in resolving the issue -
The client connection is not allowed on the internal edge of the Access Edge Server
We are trying to setup Lync 2013 Edge Server, we have a setup as described below
Real IPs for Lync Edge/WebConf/AV
NAT of real IPs through Firewall Juniper to FE IP
Topology with NAT (Firewall IP) IP enabled
Certificates for with SAN for sip.acme.com etc (Both certs are Client Server Auth Templates from Internal MS CA)(Trusted) on Edge
Route 192.215.0.0 255.255.255.0 gateway (=firewall internal ip address)
But when external user connects and we are tracing the connection we are getting below error and lync client is
not able to connect.
TL_INFO(TF_CONNECTION) [1]0AD8.0C30::09/07/2014-08:11:13.091.0000000f
(SIPStack,SIPAdminLog::WriteConnectionEvent:SIPAdminLog.cpp(454))[4150361027] $$begin_recordSeverity: information
Text: TLS negotiation started
Local-IP: 192.215.0.xxx:5061 (Edge IP)
Peer-IP: 192.215.0.xxx:1835 (Firewall IP)
Connection-ID: 0x1100
Transport: TLS
$$end_record
TL_ERROR(TF_CONNECTION) [0]0AD8.0638::09/07/2014-08:12:45.279.0000005d (SIPStack,SIPAdminLog::WriteConnectionEvent:SIPAdminLog.cpp(389))[4150360514] $$begin_record
Severity: error
Text: The client connection is not allowed on the internal edge of the Access Edge Server
Peer-IP: 192.xxx.0.xxx:1322 (firewall ip)
Transport: TLS
Result-Code: 0xc3e93d6b SIPPROXY_E_CONNECTION_INTERNAL_FROM_CLIENT
$$end_recordHi pshetty,
Check the following blog to deploy your Edge Server:
http://jsilverdrake.blogspot.se/2012/04/publishing-lync-with-forefront-tmg-part_25.html
Note: Microsoft is providing this information as a convenience to you. The sites are not controlled by Microsoft. Microsoft cannot make any representations regarding the quality, safety, or suitability of any software or information found there. Please make
sure that you completely understand the risk before retrieving any suggestions from the above link.
You need to create persistent static routes on the internal interface to all internal networks.
Regards,
Lisa Zheng
Lisa Zheng
TechNet Community Support -
Moving data in all the internal tables to the final table t_data
hi all,
how to data in all the internal tables to the final table t_data
*selecting fields from bkpf table
SELECT bukrs
belnr
gjahr
bldat
xblnr
usnam
FROM bkpf
INTO TABLE t_bkpf
WHERE bukrs EQ po_bukrs AND
belnr IN so_belnr AND
budat IN so_budat AND
blart IN so_blart.
IF t_bkpf[] IS INITIAL.
MESSAGE a999(zfi_ap_gl) WITH text-011.
STOP.
ELSE.
*selecting fields from bseg table.
SELECT bukrs
belnr
gjahr
koart
shkzg
dmbtr
zuonr
sgtxt
kostl
hkont
lifnr
prctr
FROM bseg
INTO TABLE t_bseg
FOR ALL ENTRIES IN t_bkpf
WHERE bukrs EQ t_bkpf-bukrs AND
belnr EQ t_bkpf-belnr AND
gjahr EQ t_bkpf-gjahr AND
lifnr IN so_lifnr.
ENDIF.
IF t_bseg[] IS INITIAL.
MESSAGE a999(zfi_ap_gl) WITH text-011.
STOP.
ELSE.
*selecting the companies address from adrc table
SELECT SINGLE addrnumber street str_suppl2 city1
region post_code1
FROM adrc
INTO wa_adrc
WHERE addrnumber EQ w_adrnr.
*selecting adrnr from the lfa1 table
SELECT lifnr adrnr name1 ort01 regio pstlz
FROM lfa1
INTO TABLE t_adrnr
FOR ALL ENTRIES IN t_bseg
WHERE lifnr EQ t_bseg-lifnr.
IF NOT t_adrnr[] IS INITIAL.
*populating the t_vaddress table.
SELECT addrnumber
street
str_suppl2
FROM adrc
INTO TABLE t_vaddress
FOR ALL ENTRIES IN t_adrnr
WHERE addrnumber EQ t_adrnr-adrnr.
*populating the t_vendor table with the vendor address
SELECT lifnr
adrnp_2
namev
name1
INTO TABLE t_vendor
FROM knvk
FOR ALL ENTRIES IN t_adrnr
WHERE lifnr EQ t_adrnr-lifnr AND
adrnp_2 EQ t_adrnr-adrnr.
ENDIF.
ENDIF.Loop the internal table which is having the maximum number of records,then use read table....for other internal tables....in that loop and then append them into final internal table.
Ex-LOOP AT IT_VBRP INTO WA_VBRP.
WA_FINAL-WERKS = WA_VBRP-WERKS_I.
WA_FINAL-KUNAG = WA_VBRP-KUNAG.
WA_FINAL-AEDAT = WA_VBRP-AEDAT.
READ TABLE IT_KONV INTO WA_KONV WITH KEY KNUMV = WA_VBRP-KNUMV
KPOSN = WA_VBRP-POSNR_I.
IF SY-SUBRC EQ 0.
WA_FINAL-KSCHL = WA_KONV-KSCHL.
CLEAR WA_KONV.
ENDIF.
READ TABLE IT_KNA1 INTO WA_KNA1 WITH KEY KUNNR = WA_VBRP-KUNAG.
IF SY-SUBRC EQ 0.
WA_FINAL-NAME1 = WA_KNA1-NAME1.
CLEAR WA_KNA1.
ENDIF.
ENDIF.
APPEND WA_FINAL TO IT_FINAL.
CLEAR: WA_FINAL,WA_KONV,wa_kna1.
ENDLOOP. -
How to Read the internal table for the data download from the spool
HI all,
I have one issue regarding the spool ,we are getting the correct output as per requirement of user but when we send the same to the user in pdf format they did notget the same.
they are telling that the due date is missing from the pdf.
Please advice me how to track the internal table for the spool data converted intopdf in a readable format.
the FM used for the above task is :
call function 'CONVERT_OTFSPOOLJOB_2_PDF'
Please reply if any one worked on the same.
Thanks in advance.
Gaurav,Hi Wang,
Please let me know how you solved your question.
Points will be rewarded.
Thanks,
Arun. -
Format the internal memory of the DMP
Anyone know how I can format the internal memory of the DMP?
I store content in the internal memory of the DMP and USB memory, but a few days from the date the DMPs generate files with strange names (junk files).
To delete these junk files, I remove the drive and formatting on a computer.
But it is hard work, since I have 300 DMPs.
Thanks for your comments.
RegardsYes that would work. You can put two 2gb RAM sticks in your model 2,1 but it can only use 3,3gb. This is a hardware limitation and cannot be changed.
http://en.wikipedia.org/wiki/3_GB_barrier
http://www.everymac.com/systems/apple/macbook_pro/faq/macbook-pro-core-2-duo-3-g b-memory-limitation-details.html
OWC tests have found that there is a slight speed increase with having two 2gb sticks in rather than one 1gb and one 2gb. Your model is in the gray lines at the bottom of the graph. http://eshop.macsales.com/shop/Memory_Benchmark/Apple_MacBook/
These are good online stores for Mac compatible RAM
OWC http://eshop.macsales.com/shop/memory/MacBook/DDR2/ - They offer Mac tested RAM at very good prices.
Crucial Memory http://www.crucial.com/ - good place to buy RAM from all over the world. They also have an excellent memory selector that allows you to choose memory based on your computer's model
Data Memory Systems http://www.datamemorysystems.com/apple-memory.asp - another good, cheap place to buying RAM if you live in the U.S.
Here are instructions on replacing RAM in a MacBook with a removable battery. http://homeoffice.consumerelectronicsnet.com/articles/viewarticle.jsp?id=44404
If you don’t have the tools to open up the MacBook OWC has a set for $5.
http://eshop.macsales.com/item/OWC/TOOLKITMHD/ -
After using the internal mic for the first time I am getting a buzzing feedback from my audio output
After using the internal mic for the first time I am getting a buzzing feedback from my audio output
Go to System Preferences Sound Input and adjust the volume level down by dragging the slider to the left. With an audio app like Logic there is an option for input monitoring when recording so there might be a feedback loop if the volume is set too high. Garage Band works in a similar way. Always be careful when using headphones as the noise can be frightful and cause hearing damage.
-
What does the "Internal" value on the ASM Disk Group Usage Chart represent?
In OEM Grid Control, on the Automatic Storage Management Home page there is the Disk Group Usage Chart.
What does the "Internal (GB)" value on this pie chart represent? and how it has been calculated?
On one of our servers it is 13% of available ASM disk capacity.. and on another it is 0%.Internal space is (Total MB - Free MB) from the @ DiskSpaceUsage - Total MB from the DatabaseDiskSpace usage
It is basically the space occupied by the your DB in the ASM disk space. There are few bugs related to this and need to be refined
regards
Pravin -
The internal hard drive on my early 2009 24" iMac is nearly full. I have already worked to free as much space on the HD as possible. How do I add an external HD and have the iMac read it as though it was part of the internal HD. I know about external HD for additional storage and I do have an external HD, but, it is so much easier to search the drive when it is internal than having to perform a search on the internal drive and then a search on the external drives. And, it is easier to save files to an internal drive so that I don't have to decide which external drive to use to save files. In other words, I want to add an external HD and have it function as though I had purchased a larger internal HD.
That is simply not possible. Every drive is a separate device. It cannot be used to extend an internal drive as though you had a seamlessly larger drive.
What you can do is to create a striped RAID array using the internal drive and an external drive. However, doing this will erase the internal drive and you will lose everything on the internal drive. Furthermore, installing Lion or Mountain Lion becomes a bit of a problem because you cannot create a Recovery HD on a RAID and this tends to make the installer choke. However, you can clone an existing Lion or Mountain Lion system to the RAID and designate the RAID as a startup volume.
I would not recommend the RAID solution, personally, but there are many who do. I prefer the basic solution of spending the money on a larger internal hard drive instead of an external hard drive.
RAID Basics
For basic definitions and discussion of what a RAID is and the different types of RAIDs see RAIDs. Additional discussions plus advantages and disadvantages of RAIDs and different RAID arrays see:
RAID Tutorial;
RAID Array and Server: Hardware and Service Comparison.
Hardware or Software RAID?
RAID Hardware Vs RAID Software - What is your best option?
RAID is a method of combining multiple disk drives into a single entity in order to improve the overall performance and reliability of your system. The different options for combining the disks are referred to as RAID levels. There are several different levels of RAID available depending on the needs of your system. One of the options available to you is whether you should use a Hardware RAID solution or a Software RAID solution.
RAID Hardware is always a disk controller to which you can cable up the disk drives. RAID Software is a set of kernel modules coupled together with management utilities that implement RAID in Software and require no additional hardware.
Pros and cons. Software RAID is more flexible than Hardware RAID. Software RAID is also considerably less expensive. On the other hand, a Software RAID system requires more CPU cycles and power to run well than a comparable Hardware RAID System. Also, because Software RAID operates on a partition by partition basis where a number of individual disk partitions are grouped together as opposed to Hardware RAID systems which generally group together entire disk drives, Software RAID tends be slightly more complicated to run. This is because it has more available configurations and options. An added benefit to the slightly more expensive Hardware RAID solution is that many Hardware RAID systems incorporate features that are specialized for optimizing the performance of your system.
For more detailed information on the differences between Software RAID and Hardware RAID you may want to read: Hardware RAID vs. Software RAID: Which Implementation is Best for my Application? -
Checkbox as one of the field in the internal table in the list
Hi,
I have a requirement of processing the certain records of the internal table for which checkboxes are selected in the list.
The selected records need to be updated in the custom table and the unselected records need to be ignored.
I have created the PF status and the application tool bar and a button on the tool bar.
Then when the report is executed the list is displayed with the records with one of the field as a checkbox.
At user-command.
Then in the at user-command handling the button click event.
I want to know which records are been selected and which are not.
If some one knows please let me know.
Thanks
S PatelThis is exactly what you need to do:-
PBO
CREATE OBJECT g_custom_container
EXPORTING container_name = g_container.
CREATE OBJECT g_grid
EXPORTING i_parent = g_custom_container.
Select data from your table
PERFORM select_data CHANGING pt_outtab[].
Build fieldcat
PERFORM build_fieldcat CHANGING pt_fieldcat.
Exclude standard buttons from the Toolbar
PERFORM exclude_tb_functions CHANGING lt_exclude.
Display output in ALV grid
CALL METHOD g_grid->set_table_for_first_display
EXPORTING
it_toolbar_excluding = lt_exclude
CHANGING
it_fieldcatalog = pt_fieldcat
it_outtab = pt_outtab[].
PAI
Get modified data
CALL METHOD gv_grid->check_changed_data.
LOOP AT gt_output INTO wa_output WHERE zzchkbox EQ c_x.
MOVE-CORRESPONDING wa_output TO wa_selblk.
APPEND wa_selblk TO lt_selblk.
ENDLOOP.
This method will give you all the records which are selected in the list output. Collect them and modify your custom table.
Edited by: Rudresh Chand on Feb 28, 2010 8:26 AM -
Canvas on the Internal Frame overlap the Menus.!!!
hi friends
i have added canvas on the internal frame(contentpane).
when internal frame appears on the screen menus are being overlapped.
it means if i open the menu they will be hide behind canvas and can not be seen.
plzz guide me what to do?This is a typical problem when mixing Swing (JFrame) components with AWT components (Canvas). Make sure you stick to only one of these GUI packages when implementing your own gui.
Have a look at the java tutorial.
http://java.sun.com/docs/books/tutorial/uiswing/painting/overview.html
Manuel Amago. -
Problem with downloading the internal table onto the presentation server.
Hey folks,
I have a problem where in i am downloading one year of sales done by the company. I wrote a program to download the file onto the presentation server . The error occurs in the FM GUI_DOWNLOAD where if the file exceeds 105843504 bytes its giving me a dump saying that
When the program was running , it was established that more memory was needed than the operating system is able to safely to provide.
The current program has to be terminted because of the program already requested 105843504 bytes from the operating system with malloc when the operating system reported after further memory request that there was no more memory space available.
Could somebody provide an alternative soltuion for this.
Its really urgent as i can download the file with 70,000,000 bytes
Regards
RockHi Rock,
Please download the files on to Application Server, else as suggested by Ashish download into 2 or 3 files and merge them manually.
Declare same internal tables may be 5 times.
When you fill the internal table check for a counter and when you hit a certain number stop appending to it and start appending to the next.
After you are done so download all the internal tables.
I guess this would be a good way. I am not sure if there are any ther alternative good methods.
Hope this helps.
Shreekant
Maybe you are looking for
-
How can we generate PDF file by passing a query from package to RDF?
Hi Everyone, I am beginner as SQL Developer, I am stuck in one issue , that is regarding generating PDF or Excel file according to user parameters passed. Detail of Requirement : I have created one package it contains 2 functions and 1 Procedure . Al
-
How to show value and unit in different columns
Hi All, I need ABAP help for the below requirement in BI7.0 Data source contains the field Amount in local currency (Data source is flat file of CSV format) Amount in local currency 1000 INR 2000 INR 1000 GBP 2000 EUR
-
Hello Friends, I am new in InDesign Java Script
Hello Friends, I am new in InDesign Java Script. I want to edit the page's master text Frame Object through Java Script. Any Idea regarding this will help me a lot. thanks in advance
-
Opening pdfs with ibooks ipad: problem
Hi, I found that many people have this problem: opening a pdf (that's attached to an email) with ibooks, used to work perfectly. And now it doens't anymore. Sometimes (1 on 20 tries) it does work. Often the pdf lights up for a second in ibooks, and t
-
hi guys i need your help hope someone can point me to the right direction one of client has their website hosted by a 3rd party company , however they needed exchange 2013 on their environment. at the 3rd party CP has deleted the mx record and A reco