When i active my mac pro all i get is a white screen and  it loading .. and when it fully loaded it turns off and the same thing keep on happening again

when i active my mac pro all i get is a white screen and  it loading and when it fully load its turn off , and it keep on doing the same thing for hours

Hi Shahenaz,
It's a little difficult to understand exactly what's going on with your mac based on the description you gave. Is there anything else you could add? Is it stuck in a reboot loop? Or is it just showing a white screen forever?
I had pretty much the same problem a few days ago, and was worried my mac was screwed permanently, but I got it fixed up no problem!
Follow these steps to try and troubleshoot/fix the problem.
1. Boot into OSX Recovery Mode
First, turn off your Mac. If it isn't responding, or is stuck in a reboot loop, just hold down the power button until it turns off, and you hear the fans stop. Then boot it while holding the Command and R keys. If it successfully boots into OSX Recovery Mode, continue with this step. If not, skip to step two. (My Mac couldn't successfully boot into the recovery mode, so I had to go to step 2)
Select "Disk Utility" from the list of options, and find your built in hard drive from the list on the left. Usually there are two listings/names for your drive. The first should be something like "500GB longchainoflettersnumbers Media". Then the one below will be a little easier on the eyes, named Macintosh HD, if you haven't changed its name. That's the one you want, click it.
Now go to the "First Aid" tab. Click on the "Verify Disk" button in the bottom right corner, and let it do its thing. Once that's done, hit repair disk, also in the bottom right corner. If your disk is corrupted, you may need to run the repair process several times, before it comes up completely clean.
Once this is done, select Shut Down from the Apple menu and, once your Mac is completely off, turn it back on like normal. If it works, great. If not, proceed to step two.
2. SafeBoot
Sometimes, when a mac is acting up and doesn't want to start, all it takes is a safe boot, followed by a regular restart. Or maybe you recently installed a program that either has malicious or errored coding that's causing your troubles. This is where Safe Boot comes in.
Turn off your mac, and reboot it while holding Shift. (If you want to see the process that's going on in the background, boot while holding Shift, Command, and V. This will enter something called Verbose Mode).
If it boots successfully into Safe Mode, great. If you believe that there's a particular program that you recently downloaded that might be causing your trouble, now's the time to delete it. If not, just reboot normally and see if it works! If it doesn't, or if your Mac didn't even Safe Boot like mine, proceed to step 3.
3. Fsck!
For this step, you're going to be booting your mac into Single User Mode. I'm not going to go into details as to what this step does, but it works for some people. Here are the steps.
Turn off your mac, and reboot it while holding Command and S. The screen should go black, and you'll see some white text run across the screen, wait a few seconds, until you see the command prompt. Now type
fsck -fy
and hit the Enter key. This will run a series of system checks, which could take a few minutes. Be patient on this part. Once it's done, it will show one of two messages:
1. "The volume (your Mac) appears to be OK
or
2. "File System Was Modified"
If you got message 1, type reboot and press Return. Hopefully your computer works after this - if not, proceed to step 4.
If you got message 2, run the same command again until you get message 1. If it doesn't seem to be working, turn off your system and proceed to step 4.
If you couldn't even boot into Single User Mode in the first place (like me), go to step 4 anyways.
Step 4: Reset the NVRAM
The NVRAM is another kind of RAM that stores data like the computer volume you had set before you turned it off, or the screen brightness, resolution etc. This memory is saved, unlike with regular RAM. Resetting it isn't harmful to your system, it will just put your screen brightness, volume, etc. to defaults.
Turn off your Mac, and reboot while holding Command, Option, P, and R, and continue holding them down until you hear the computer restart again.
I can't really explain why to do this step, I just know it works for some people, and seems to be what unbricked my MacBook Pro. If none of these steps, fixed your Mac, well the situation is looking pretty grim. Try setting up a meeting with a Mac Genius at your local Apple store. However, I know that many other people with these symptoms ended up having a logic board failure. Apple can swap out your logic board for a new one, but the price is pretty hefty, somewhere around $300 I believe.
Well I wish you luck, I hope this helped you!

Similar Messages

  • I replaced the battery on my RAID card, when I booted my mac pro up, I get the folder with the question mark. I used a boot USB drive to boot and when I looked in the RAID utility, my RAID 5 volumes were no longer showing, advise.

    I replaced the battery on my RAID card, when I booted my mac pro up, I get the folder with the question mark. I used a boot USB drive to boot and when I looked in the RAID utility, my RAID 5 volumes were no longer showing, advise.
    Ernest

    Not sure if I'm following you. I have 4 hard drives installed on my Mac Pro. I had a RAID 5 configured and functional for about 5 months. My battery died on the RAID card. I replaced the battery, seated the RAID card back in the slot I removed it from. When I booted to the USB drive to look in the RAID utility, I could see the battery is charged but my volumes are not showing.
    The drives don't show in disk Utility. I built the RAID with the RAID Utility and they did show there. I have a early 2008 Mac Pro, Mavricks OS running Mac Server

  • After "restoring" my MacBook Pro via time capsule, all I get is a white screen with the apple in the middle and the little spin wheel spinning and spinning and spinning for 24 hrs now...

    After "restoring" my MacBook Pro via time capsule, all I get is a white screen with the apple in the middle and the little spin wheel spinning and spinning and spinning for 24 hrs now...

    Hello kdcha55,
    Thanks for using Apple Support Communities. 
    To troubleshoot this issue where your Mac is stuck on the gray screen with a spinning gear, please follow the steps in the support article linked to below.
    Mac OS X: Gray screen appears during startup
    http://support.apple.com/kb/TS2570
    Take care,
    Alex H.

  • I can't log on to my I mac Desk top, every time I switch it on all I get is a white screen with the apple log , can anyone help pls?

    I can't log on to my I mac Desk top, every time I switch it on all I get is a white screen with the apple log , can anyone help pls?

    Hello,
    Could be many things, we should start with this...
    "Try Disk Utility
    1. Insert the Mac OS X Install disc, then restart the computer while holding the C key.
    2. When your computer finishes starting up from the disc, choose Disk Utility from the Installer menu at top of the screen. (In Mac OS X 10.4 or later, you must select your language first.)
    *Important: Do not click Continue in the first screen of the Installer. If you do, you must restart from the disc again to access Disk Utility.*
    3. Click the First Aid tab.
    4. Select your Mac OS X volume.
    5. Click Repair Disk, (not Repair Permissions). Disk Utility checks and repairs the disk."
    http://docs.info.apple.com/article.html?artnum=106214
    Then try a Safe Boot, (holding Shift key down at bootup), run Disk Utility in Applications>Utilities, then highlight your drive, click on Repair Permissions, reboot when it completes.
    (Safe boot may stay on the gray radian for a long time, let it go, it's trying to repair the Hard Drive.)
    If perchance you can't find your install Disc, at least try it from the Safe Boot part onward.
    If 10.7.0 or later...
    Bootup holding CMD+r, or the Option/alt key to boot from the Restore partitirion & use Disk Utility from there.

  • HT5055 Just updated to lion and my cctv access has stopped functioning all I get is a white screen in the middle of the control panel where the camera shots should be.  I think it is caused by JAVA but am confused as when i view on snow leopard it works 

    Just updated to lion and my cctv access has stopped functioning all I get is a white screen in the middle of the control panel where the camera shots should be.  I think it is caused by JAVA but am confused as when i view on snow leopard it works  can you help

    Open "Java Preferences" either from spotlight or your utilities folder...it's probably going to say you need to install a java runtime. Then just click install!

  • I bought garage band from the app store and downloaded it to my mac mini. When i try to open a screen comes up explaining i need to down load missing files. I do this but when try to open GB again the same thing keeps happening! Can anyone help.

        I bought garage band from the app store and downloaded it to my mac mini. When i try to open a screen comes up explaining i need to down load missing files. I do this but when try to open GB again the same thing keeps happening! Can anyone help.
    Thanks
    Hugh Lockwood

    Hi, Hugo,
    In similar cases it helped to remove the GarageBand "Preferences" file from the User Library.
    Open the folder
        your home folder > Library > Preferences
    and move the file "com.apple.garageband.plist" to the Desktop.
    Then try again to launch GarageBand.
    Regards
    Léonie

  • When i press sleep wake button to turn on my iphone 3gs all i get is a white screen

    trying to open the phone to make a call or answer the phone when i press the sleep wake button all i get is a white screen and cant do anything with the phone constantly turning phone on/off eventually my home page does return anyone know why and what to do.. thanks to all

    MacBook Air Mid 2012?
    "Apple has determined that certain 64GB and 128GB flash storage drives used in the previous generation of MacBook Air systems may fail. These systems were sold between June 2012 through June 2013."
    http://www.apple.com/support/macbookair-flashdrive/

  • When i turn my touch all i get is a white screen  help

    when i turn on my touch all i get is a white screen  help

    Try a system reset.  It cures many ills and it's quick, easy and harmless...
    Hold down the on/off switch and the Home button simultaneously until the screen blacks out or you see the Apple logo.  Ignore the "Slide to power off" text if it appears.  You will not lose any apps, data, music, movies, settings, etc.
    If the Reset doesn't work, try a Restore.  Note that it's nowhere near as quick as a Reset.  From iTunes, select the iPad and then select the Summary tab.  Follow directions for Restore and be sure to say "yes" to the backup.  You will be warned that all data (apps, music, movies, etc.) will be erased but, as the Restore finishes, you will be asked if you wish the contents of the backup to be copied to the iPad.
    There's more to try but let's go a bit at a time.

  • HT201412 when turned on all I get is a white screen

    My Ipod when turned on all I get is a white screen.  I tryed to do a reboot w/power and home button and nothing

    Try:
    - iOS: Not responding or does not turn on
    - Also try DFU mode after try recovery mode
    How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
    - If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
    - Try on another computer
    - If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
      Apple Retail Store - Genius Bar

  • Hello,I have done this successful in the past but on my IPad it shows I have 4 apps that need to be updated so when I hit the update tab all I get is a white screen. When I hit the purchase or other tabs it opens up. What could be the problem?

    ****,I have done this successful in the past but on my IPad it shows I have 4 apps that need to be updated so when I hit the update tab all I get is a white screen. When I hit the purchase or other tabs it opens up. What could be the problem?

    There have been numerous reports on the forum today regarding this issue. It seems to be an issue at Apple, but no information has been posted on the status site.
    http://www.apple.com/support/systemstatus/

  • Hi guys, a game I'm trying to play keeps unexpectedly closing every time I try to play. When I try reopening, the same thing keeps popping up so I don't really know how to fix that problem. Can you help?

    Hi guys, a game I'm trying to play keeps unexpectedly closing every time I try to play. When I try reopening, the same thing keeps popping up so I don't really know how to fix that problem. Can you help?

    Plus this showed up when I looked up the details of why it quit unexpectedly.
    Process:         launchd [458]
    Path:            /Users/USER/Library/Application Support/Steam/*/Starbound.app/Contents/MacOS/starbound
    Identifier:      com.chucklefish
    Version:         ??? (???)
    Code Type:       X86-64 (Native)
    Parent Process:  launchd [154]
    Date/Time:       2014-01-06 19:19:28.898 -0500
    OS Version:      Mac OS X 10.7.5 (11G63b)
    Report Version:  9
    Interval Since Last Report:          1786 sec
    Crashes Since Last Report:           23
    Per-App Crashes Since Last Report:   23
    Anonymous UUID:                      6F40DBC0-08A7-4A21-A80E-185F669D1C93
    Crashed Thread:  Unknown
    Exception Type:  EXC_BAD_ACCESS (SIGSEGV)
    Exception Codes: KERN_INVALID_ADDRESS at 0x00007fff5fc01028
    Backtrace not available
    Unknown thread crashed with X86 Thread State (64-bit):
      rax: 0x0000000000000055  rbx: 0x0000000000000000  rcx: 0x0000000000000000  rdx: 0x0000000000000000
      rdi: 0x0000000000000000  rsi: 0x0000000000000000  rbp: 0x0000000000000000  rsp: 0x0000000000000000
       r8: 0x0000000000000000   r9: 0x0000000000000000  r10: 0x0000000000000000  r11: 0x0000000000000000
      r12: 0x0000000000000000  r13: 0x0000000000000000  r14: 0x0000000000000000  r15: 0x0000000000000000
      rip: 0x00007fff5fc01028  rfl: 0x0000000000010203  cr2: 0x00007fff5fc01028
    Logical CPU: 2
    Binary images description not available
    External Modification Summary:
      Calls made by other processes targeting this process:
        task_for_pid: 1
        thread_create: 0
        thread_set_state: 0
      Calls made by this process:
        task_for_pid: 0
        thread_create: 0
        thread_set_state: 0
      Calls made by all processes on this machine:
        task_for_pid: 1095
        thread_create: 0
        thread_set_state: 0
    Model: MacBookPro8,1, BootROM MBP81.0047.B27, 2 processors, Intel Core i5, 2.3 GHz, 4 GB, SMC 1.68f99
    Graphics: Intel HD Graphics 3000, Intel HD Graphics 3000, Built-In, 384 MB
    Memory Module: BANK 0/DIMM0, 2 GB, DDR3, 1333 MHz, 0x80AD, 0x484D54333235533642465238432D48392020
    Memory Module: BANK 1/DIMM0, 2 GB, DDR3, 1333 MHz, 0x80AD, 0x484D54333235533642465238432D48392020
    AirPort: spairport_wireless_card_type_airport_extreme (0x14E4, 0xD6), Broadcom BCM43xx 1.0 (5.106.198.19.22)
    Bluetooth: Version 4.0.8f17, 2 service, 18 devices, 1 incoming serial ports
    Network Service: Wi-Fi, AirPort, en1
    Network Service: BlackBerry (en3), Ethernet, en3
    Serial ATA Device: TOSHIBA MK3265GSXF, 320.07 GB
    Serial ATA Device: MATSHITADVD-R   UJ-8A8
    USB Device: FaceTime HD Camera (Built-in), apple_vendor_id, 0x8509, 0xfa200000 / 3
    USB Device: hub_device, 0x0424  (SMSC), 0x2513, 0xfa100000 / 2
    USB Device: Apple Internal Keyboard / Trackpad, apple_vendor_id, 0x0252, 0xfa120000 / 5
    USB Device: BRCM2070 Hub, 0x0a5c  (Broadcom Corp.), 0x4500, 0xfa110000 / 4
    USB Device: Bluetooth USB Host Controller, apple_vendor_id, 0x821a, 0xfa113000 / 7
    USB Device: hub_device, 0x0424  (SMSC), 0x2513, 0xfd100000 / 2
    USB Device: RIM Network Device, 0x0fca, 0x8013, 0xfd120000 / 4
    USB Device: IR Receiver, apple_vendor_id, 0x8242, 0xfd110000 / 3

  • All i get is a white screen

    all i get is a white screen then goes black

    Try #2 and 3 in link below.
    Basic troubleshooting steps. 
    17" 2.2GHz i7 Quad-Core MacBook Pro  8G RAM  750G HD + OCZ Vertex 3 SSD Boot HD 

  • When i go to install creavtive cloud it says check the connection, try again but however my connection is fine and i've tried my friends connection and the same thing keeps happening  HELP!!!

    when i go to install creavtive cloud it says check the connection, try again but however my connection is fine and i've tried my friends connection and the same thing keeps happening  HELP!!!

    Sign in, activation, or connection errors | CS5.5 and later
    Mylenium

  • After refusing an update now all I get is a white screen with the firefox logo. If I have to reinstall firefox 3.66, how can I transfer my firefox profile with bookmarks etc, to the new installation?

    After refusing an update now all I get is a white screen with the firefox logo. If I have to reinstall firefox 3.66, how can I transfer my firefox profile with bookmarks etc, to the new installation?
    == This happened ==
    Every time Firefox opened

    -> press '''F11''' to bring the computer out of FullScreen
    -> Tap '''ALT''' key or press '''F10''' to show the Menu Bar
    -> go to View Menu -> '''Zoom''' -> click '''Reset''' -> '''Page Style''' -> select '''Basic Page Style'''
    -> go to View Menu -> Toolbars -> select '''Menu Bar''' and '''Navigation ToolBar''' -> unselect All Unwanted/Incompatible Toolbars
    -> go to Tools Menu -> Options -> General -> '''When Firefox starts : select "Show My Home Page"''' -> Type the address of the website which you want to be your HomePage e.g. http://www.google.com
    -> go to Tools Menu -> Options -> Content -> place Checkmarks on:
    1) Block Pop-up windows 2) Load images automatically 3) Enable JavaScript
    -> go to Tools Menu -> Options -> Privacy -> History section -> '''Firefox will: select "Remember History"'''
    -> go to Tools Menu -> Options -> Security -> place Checkmarks on:
    1) Warn me when sites try to install add-ons 2) Block reported attack sites 3) Block reported web forgeries 4) Remember Passwords for sites
    -> Click OK on Options window
    -> go to Tools Menu -> Add-ons -> Extensions section -> REMOVE All Unwanted/Suspicious/Incompatible Extensions (Add-ons)
    -> go to Tools Menu -> Add-ons -> Appearance section -> REMOVE All Unwanted/Suspicious/Incompatible Themes (Persona)
    Now Restart Firefox. Check and tell if its working.

  • All i get is a white screen. no more firefox

    all i get is a white screen no firefox

    A possible cause is security software (firewall) that blocks or restricts Firefox or the plugin-container process without informing you, possibly after detecting changes (update) to the Firefox program.
    Remove all rules for Firefox from the permissions list in the firewall and let your firewall ask again for permission to get full unrestricted access to internet for Firefox and the plugin-container process and the updater process.
    See:
    *https://support.mozilla.com/kb/Server+not+found
    *https://support.mozilla.com/kb/Firewalls

Maybe you are looking for

  • How can you create a screen width slide show?

    I have created screen width images that resize depending on the screen resolution using the fill option. However, when I use any of the slide show widgets and size them to the edge of the site, it doesn't fill the screen width on the live mode. It al

  • Reader add-on will not stay in IE 10

    I recently upgraded from IE 9 to IE 10.  I cannot open .pdf files in IE 10, although I can save them to my desktop and open them from there.  Firefox opens .pdf files. I went to manage add-ons in IE 10, and Reader was not there.  I re-installed Reade

  • Settlement with KO8G

    Hi, We are running KO8G for collective settlement of work orders & finding some orders in Inappropriate status without explaination of what are those order nos. need to know is there any report in CO or table where 1. We can find out all the orders w

  • Checkpoint not complete error in alert log

    version : 10.2.0.5 , 11.2.0.2 This is what I found about "Checkpoint not complete" from google "+This message indicates that Oracle wants to reuse a redo log file, but the current checkpoint position is still in that log. In this case, Oracle must+ +

  • Batch folder rename

    Is there a way to batch rename folders? I have a series of folders that I have inherited and they all have a digit at the end which I would like to remove. I really don't want to do this manually. I've looked at Automator but can't see a solution the