When I open my Macbook Pro it shows past date

Hi -
Sometimes (pretty consistently lately) when I open my Macbook Pro it shows the screen that was there when I closed it, but everything is greyed. There is a line at the bottom that is moving across and when it finishes the color goes back to normal. But even then, the time is from when I closed it, and the computer is unresponsive. It will sometimes sit in this state for a couple of minutes or longer.
This is a six month old Macbook Pro and this happens pretty regularly, and has off and on since I first got it.
Is this just no more than annoying? I've been using Apple laptops since 2005 and never had this happen until this machine (which is my third personal one - I support two others). Any ideas on cause?
Thanks
Craig

Some users have reported solving this problem by resetting the NVRAM (PRAM.)
If you've installed something called "iCleanMemory," or any other third-party software that is supposed to "clean" or "free up" memory, remove it according to the developer's instructions after backing up all data. Reboot and test. If there's no change, continue.
Please read this whole message before doing anything.
This procedure is a diagnostic test. It’s unlikely to solve your problem. Don’t be disappointed when you find that nothing has changed after you complete it.
The purpose of the test is to determine whether the problem is caused by third-party software that loads automatically at startup or login, by a peripheral device, or by corruption of certain system caches.
Disconnect all wired peripherals except those needed for the test, and remove all aftermarket expansion cards. Boot in safe mode and log in to the account with the problem. Note: If FileVault is enabled on some models, or if a firmware password is set, or if the boot volume is a software RAID, you can’t do this. Ask for further instructions.
Safe mode is much slower to boot and run than normal, and some things won’t work at all, including sound output and Wi-Fi on certain models. The next normal boot may also be somewhat slow.
The login screen appears even if you usually log in automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin. Test while in safe mode. Same problem? After testing, reboot as usual (i.e., not in safe mode) and verify that you still have the problem. Post the results of the test.

Similar Messages

When i open my macbook pro- the screen lights up and then goes black-

When I open my Macbook pro- the screen lights up and then goes black- keybook stays backlite- can not get screen to come back on. Must reboot-
thoughts-?? Macbook is 6 months old and on second hard drive ( failure after 45 days).

Hey! exact same thing happens to me... I use the keyboard shortcut to turn off the screen which is ctrl - shift - eject button. Then just poke a key and it wakes up again fine, it doesn't fix the problem but at elast you don't have to reboot. x

When I open my MacBook Pro for the first time each day, I find condensation on the glass. What can I do to prevent the condensation?

When I open my MacBook Pro for the first time each day, I find condensation on the glass. What can I do to prevent the condensation?

This thread and all the followups are hilarious, if it weren't such a serious problem. OP, you may want to add a bit more information on how this drippy screen problem occurs: where do you live, what are the weather conditions, what are you doing with the Mac when it occurs, etc.
Yes, extreme moisture, to the extent of causing visible condensation, is Very Bad News for any electronic device, and more so with one that isn't tropicalized like the Mac. Besides trying to avoid subjecting it to such extreme temperature changes, using some kind of desiccant to absorb close range moisture and avoidint its use until it dried out, I can suggest placing some kind of absorbent material between the display and the keyboard to prevent the moisture on the glass from finding its way into the computer. Like the protective poliethylene foam protector that came with the Mac when new. Or something like RadTech's ScreenSavrz: http://www.radtech.us/Products/NotebookScreenSavrz.aspx

Put to Sleep and Don't wake up when i open my macbook pro

Hello,
i have a Macbook pro 17' (2,33ghz) using leopard 10.5.2 with all the latest update.
Everytime i put my computer to sleep for more than 10 minutes (random time), when i try to wake up nothing happen, i hear a strange noise of the HD for about 2 seconds and the screen stay Black.
When i close the computer again, the light stay On, when i open the computer again nothing happen, the screen is black, no buttons works, nothing happen.
So i have to press the Power button for a few seconds and then turn on my Mac again.
this happen to me every day !
i try:
Remove the charger = Same Problem
With the charger = Same Problem
With Apple Bluetooth mouse = Same Problem
Without Apple Bluetooth mouse = Same Problem
With External HD = Same Problem
Without External HD = Same Problem
when i try to wake up the Mac, I wait for more than 10 minutes and nothing happen.
i see the Log's and i can't see antything Wrong.
this is not the first time i have this problem
in 10.4.8 i have the problem, when i update to 10.4.9 "fix the problem" until 10.5.2
i have the AppleCare.
i dont know if this is a Hardware or Software problem and if the guarantee cover this?
thinkin that this could be a HD problem so i check in the disk utility and everyting is OK.
Thanks!

Well. in my searching i find an """"Answer"""
Some body was talking about that the new's Mac have something called "Safe Sleep" so when someone sleep the Mac the Information of the Ram make a copy in the HD this can take for 30 seconds to a minute. In this time, if you move the mac or do something else, generate a error and corrupt the Information of the ram and the Mac stop working.
Say that to remove this "Safe Sleep" have to open the terminal and:
The Unix command to disable SafeSleep is:
sudo pmset -a hibernatemode 0
To re-enable SafeSleep, the command is:
sudo pmset -a hibernatemode 3
Maybe Apple going to Fix this in future Updates.
Sorry for my English !

What is the cracking sound when I open my MacBook Pro lid?

When opening and closing MacBook Pro lid, it makes a cracking sound. Does anyone have an idea what it could be? It's not the hard drive because Geek Squad ran a test and everything passed.

Try this: Loosen the screws in the rear of the MBP (by the hinge) and re-torque them. See if that will alleviate the problem. You will need a 00 Philips driver.
Ciao.

Firefox is unresponsive when I open my Macbook Pro or wake it up from sleeping. Is there a fix for this problem?

Whenever I open up my Macbook Pro, Firefix is unresponsive. I can see all of my tabs, but nothing (except the top pull-down menus) are clickable. If I wait a few minutes it seems to work again, but I usually have to force quit. Anyone else have this problem?

Firefox uses plugin-container.exe to run Flash and other plugins. The theory is that if the plugin were to crash, it would not crash all your tabs, just any active plugins. Are you getting a message that a plugin crashed?
If I understand the problem correctly, Firefox is hanging or freezing when trying to open a link, and you are exiting Firefox, after which it won't start up again until you kill firefox.exe in the Task Manager.
Have you noticed any pattern to when Firefox freezes or stalls?
How are you exiting Firefox (for example, from the menu vs. red X button vs. Ctrl+Alt+Delete)?
In case you haven't seen it, this article might be useful: [[Firefox hangs or is not responding - How to fix]].

When I open the MacBook Pro, display doesn't turn on!

I have a new MacBook Pro. It doesn't seem to wake from sleep. Also, when it is operating, it doesn't respond when I try and put it to sleep. Lastly, sometimes when I shut the computer, I notice that it will remain very warm for a long time in my bag, even though it isn't plugged in. These all seem very related.
Any Suggestions?
Thanks!
Tim

Welcome to Apple Discussions!
I also had some sleep problems with my new (in September) MBP running 10.4.10. Mostly a tendency to freeze if the display went to sleep, which does not seem to be the same problem that yours has. When I went to Leopard, all of these problems vanished.
Is yours asleep or frozen? If the sleep light is steady instead of pulsing, it may be frozen. And it should not freeze.
I have never had a problem with the MBP getting warm in my bag, but then, I always shut it down rather than put it to sleep. But I have heard of others getting warm. The MBP uses its aluminum skin to cool itself, and that doesn't work well in a bag. So I don't think it's good to put it in a bag asleep although I am sure others will disagree with this.
Since it's new and under warranty, you can always take these issues up with Apple.
Good luck!

When i open my macbook pro the wifi connect but says no internet connection

Every time i close my Macbook Pro (early 2011 model running OSX Lion) then open it back up the wifi will connect to the right network but says i have no internet connection this lasts for about 5-10 minutes then the internet will finally work. i know it's not the router cause im connected on my phone and on other computers and they work just fine. is this something internal or something with the software?

Hi..
Try Resetting the System Management Controller (SMC)

When I open my MacBook Pro there is a flashing question mark

Hi, I open my MacBook and then I see a flashing question mark with a folder . What do I do?

A flashing question mark appears when you start your Mac

When I open my macbook pro it's not automatically connected to the wifi at home

Hello,
When I open my mac it's just usally is connected to the wifi itself but now I keep getting that I now have to wait 10 seconds or longer after opening my mac to have my mac connected to the wifi ! Has it something to do with Mavericks ?
Kind regards

Some users have reported solving this problem by resetting the NVRAM (PRAM.)
If you've installed something called "iCleanMemory," or any other third-party software that is supposed to "clean" or "free up" memory, remove it according to the developer's instructions after backing up all data. Reboot and test. If there's no change, continue.
Please read this whole message before doing anything.
This procedure is a diagnostic test. It’s unlikely to solve your problem. Don’t be disappointed when you find that nothing has changed after you complete it.
The purpose of the test is to determine whether the problem is caused by third-party software that loads automatically at startup or login, by a peripheral device, or by corruption of certain system caches.
Disconnect all wired peripherals except those needed for the test, and remove all aftermarket expansion cards. Boot in safe mode and log in to the account with the problem. Note: If FileVault is enabled on some models, or if a firmware password is set, or if the boot volume is a software RAID, you can’t do this. Ask for further instructions.
Safe mode is much slower to boot and run than normal, and some things won’t work at all, including sound output and Wi-Fi on certain models. The next normal boot may also be somewhat slow.
The login screen appears even if you usually log in automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin. Test while in safe mode. Same problem? After testing, reboot as usual (i.e., not in safe mode) and verify that you still have the problem. Post the results of the test.

Can someone explain why this shows up when i open my macbook pro?

It says: update necessary. And when i log in, it takes a lot of time to open, with a grey bar loading. Please help me!

Launch the Console application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ Open LaunchPad and start typing the name.
Step 1
For this step, the title of the Console window should be All Messages. If it isn't, select
          SYSTEM LOG QUERIES ▹ All Messages
from the log list on the left. If you don't see that list, select
          View ▹ Show Log List
from the menu bar at the top of the screen.
In the top right corner of the Console window, there's a search box labeled Filter. Initially the words "String Matching" are shown in that box. Enter the name of the crashed application or process. For example, if Safari crashed, you would enter "Safari" (without the quotes.)
Each message in the log begins with the date and time when it was entered. Select the messages from the time of the last crash, if any. Copy them to the Clipboard by pressing the key combination command-C. Paste into a reply to this message by pressing command-V.
☞ The log contains a vast amount of information, almost all of which is irrelevant to solving any particular problem. When posting a log extract, be selective. A few dozen lines are almost always more than enough.
Please don't indiscriminately dump thousands of lines from the log into this discussion.
Please don't post screenshots of log messages—post the text.
☞ Some private information, such as your name, may appear in the log. Anonymize before posting.
Step 2
In the Console window, select
          DIAGNOSTIC AND USAGE INFORMATION ▹ User Diagnostic Reports
(not Diagnostic and Usage Messages) from the log list on the left. There is a disclosure triangle to the left of the list item. If the triangle is pointing to the right, click it so that it points down. You'll see a list of crash reports. The name of each report starts with the name of the process, and ends with ".crash". Select the most recent report related to the process in question. The contents of the report will appear on the right. Use copy and paste to post the entire contents—the text, not a screenshot.
I know the report is long, maybe several hundred lines. Please post all of it anyway.
If you don't see any reports listed, but you know there was a crash, you may have chosen Diagnostic and Usage Messages from the log list. Choose DIAGNOSTIC AND USAGE INFORMATION instead.
In the interest of privacy, I suggest that, before posting, you edit out the “Anonymous UUID,” a long string of letters, numbers, and dashes in the header of the report, if it’s present (it may not be.)
Please don’t post other kinds of diagnostic report—they're very long and rarely helpful.

When i turn my macbook pro on , the apple logo shows up, but it is just loading. I have tried to turn if off , but the same problem appears. Someone know what the problem is?

when i turn my macbook pro on , the apple logo shows up, but it is just loading. I have tried to turn if off , but the same problem appears. Someone know what the problem is?

Boot into Safe Mode
A Safe Mode boot can take a few minutes compared to a normal boot.
Once you are in Safe Mode open System Preferences > Accounts > Login Items
If you have anything listed there to launch when you startup your Mac, delete all items.
Then go to the Apple menu / Restart.
You can also use Safe Mode to do a "live verification" of the startup disk in case it needs repairing.
Help here > Using Disk Utility to verify or repair disks

Why is it that when I plug my Macbook Pro to an external monitor, the external monitor turns black and shows the mouse only

Why is it that when I plug my Macbook Pro to an external monitor, the external monitor turns black and shows the mouse only

Hi, yes preferences sees there is a second display it recognises what make of monitor it is etc but I just get a blank blue screen on the monitor when I change it to the hdmi setting! I have tried with mirroring on and off, rearranging the displays in the preference window and lots of different resolution settings but with no difference.
An old MacBook connects fine so the monitor and hdmi port must be okay. I'm sure we have used the cable before but it could have been with the previous MacBook Air. The current one I'm using is a mid 2011 version running lion and is (according to software update) all up to date.
Any thoughts or help would be appreciated!

When I try to open a Pages document from iCloud, created on my iPad, I get message stating I need a newer version of Pages. When I go to app store all I get is "installed" when looking at pages app. my Macbook pro is up to date with all updates.

When I try to open a Pages document from iCloud, created on my iPad, I get message stating I need a newer version of Pages. When I go to app store all I get is "installed" when looking at pages app. my Macbook pro is up to date with all updates. Any ideas?

You have 2 versions of Pages on your Mac.
Pages 5 is in your Applications folder.
Pages '09/'08 is in your Applications/iWork folder.
You are alternately opening the wrong versions.
Pages '09/'08 can not open Pages 5 files and you will get the warning that you need a newer version.
Pages 5/5.01 can not open Pages 5.1 files and you will get the warning that you need a newer version.
Pages 5.1 sometimes can not open its own files and you will get the warning that you need a newer version.
Pages 5 can open Pages '09 files but may damage/alter them. It can not open Pages '08 files at all.
Once opened and saved in Pages 5 the Pages '09 files can not be opened in Pages '09.
Anything that is saved to iCloud is also converted to Pages 5 files.
All Pages files no matter what version and incompatibility have the same extension .pages.
Pages 5 files are now only compatible with themselves on a very restricted set of hardware, software and Operating Systems and will not transfer correctly on any other server software than iCloud.
Apple has not only managed to confuse all its users, but also itself.
Note: Apple has removed over 100 features from Pages 5 and added many bugs:
http://www.freeforum101.com/iworktipsntrick/viewforum.php?f=22&sid=3527487677f0c 6fa05b6297cd00f8eb9&mforum=iworktipsntrick
Archive/trash Pages 5, after exporting all Pages 5 files to Pages '09 or Word .docx, and rate/review it in the App Store, then get back to work.
Peter

HT201343 When I mirror my macbook pro to my apple tv the only thing that shows up is one video that's on my desktop. How can I watch something that's online on my laptop, on my apple tv?

When I mirror my macbook pro to my apple tv the only thing that shows up is one video that's on my desktop. How can I watch something that's online on my laptop, on my apple tv?

Are you using mirroring or using airplay within iTunes? If you are truly mirroring then you can view anything that is displayed on your computer through Apple Tv
Or provide more info on your issue

When I open my Macbook Pro it shows past date

Similar Messages

Maybe you are looking for