When I run root.sh and I get OCR errors

Hi all,
When I run root.sh and I get following errors. There are two nodes configured on Solaris 10 for Oracle Database 10g RAC Release 10.2.0.1. I am using openfiler 2.3. and ISCSI for data storage. I have create file system OCR & VOT as Raw device and formatted these devices in Solaris skipping ocr voting disk for the first 1MB to avoid overwriting the disk VTOC. Network configuration and disk permissions are set correctly. I have installed the RAC on the same machines a few months ago for training purpose and everything was working very well. Last week, my openfiler hard disk has died. I have cleared the CRS and database on the same machines and wanted to reinstall oracle RAC on Solaris but now have following problems when I run root.sh from first node I get following errors. Please help me to fix this problem.
This is the error I get:
Oracle Database 10g CRS Release 10.2.0.1.0 Production Copyright 1996, 2005 Oracle. All rights reserved.
2009-12-26 17:03:38.158: [ OCRCONF][1]ocrconfig starts...
2009-12-26 17:03:38.158: [ OCRCONF][1]Upgrading OCR data
2009-12-26 17:03:38.173: [ OCRCONF][1]OCR already in current version.
2009-12-26 17:03:38.192: [ OCRCONF][1]Failed to call clsssinit (21)
2009-12-26 17:03:38.192: [ OCRCONF][1]Failed to make a backup copy of OCR
2009-12-26 17:03:38.192: [ OCRCONF][1]Exiting [status=failed]...
This is ifconfig –a output:
lo0: flags=2001000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4,VIRTUAL> mtu 8232 index 1
inet 127.0.0.1 netmask ff000000
nfo0: flags=1000843<UP,BROADCAST,RUNNING,MULTICAST,IPv4> mtu 1500 index 2
inet 192.168.123.110 netmask ffffff00 broadcast 192.168.123.255
ether 0:22:15:19:8:d7
vfe0: flags=1000843<UP,BROADCAST,RUNNING,MULTICAST,IPv4> mtu 1500 index 3
inet 192.168.0.110 netmask ffffff00 broadcast 192.168.0.255
ether 0:1c:f0:c8:36:3a
this is hosts output:
127.0.0.1 localhost
# public network nfo0
192.168.123.110 solaris1
192.168.123.112 solaris2
# privarte interconnect - (vfe0)
192.168.0.110 solaris1-priv
192.168.0.112 solaris2-priv
# Public vertual ip vip on nfo0
192.168.123.120 solaris1-vip
192.168.123.122 solaris2-vip
# private sotartge network for Openfiler - eth0
192.168.0.195 openfiler1
This is the Format output:
AVAILABLE DISK SELECTIONS:
0. c0d0 <DEFAULT cyl 5098 alt 2 hd 255 sec 63>
/pci@0,0/pci-ide@8/ide@0/cmdk@0,0
1. c2t44d0 <DEFAULT cyl 156 alt 2 hd 64 sec 32>
/iscsi/[email protected]%3Atsn.61af7f03092f0001,0
2. c2t45d0 <DEFAULT cyl 60 alt 2 hd 64 sec 32>
/iscsi/[email protected]%3Atsn.61af7f03092f0001,1
3. c2t46d0 <DEFAULT cyl 157 alt 2 hd 64 sec 32>
/iscsi/[email protected]%3Atsn.61af7f03092f0001,2
4. c2t47d0 <DEFAULT cyl 1148 alt 2 hd 255 sec 63>
/iscsi/[email protected]%3Atsn.61af7f03092f0001,3
5. c2t48d0 <DEFAULT cyl 1148 alt 2 hd 255 sec 63>
/iscsi/[email protected]%3Atsn.61af7f03092f0001,4
6. c2t49d0 <DEFAULT cyl 1352 alt 2 hd 255 sec 63>
/iscsi/[email protected]%3Atsn.61af7f03092f0001,5
Specify disk (enter its number):
Thank you

I made a clean installation from scratch. I have prepared the servers step by step and used Metalink Note:367715.1. and I still get following errors. Do you have any recommendation or what to do?
Oracle Database 10g CRS Release 10.2.0.1.0 Production Copyright 1996, 2005 Oracle. All rights reserved.
2010-01-02 18:19:38.860: [ OCRCONF][1]ocrconfig starts...
2010-01-02 18:19:38.861: [ OCRCONF][1]Upgrading OCR data
2010-01-02 18:19:38.870: [ OCRRAW][1]propriogid:1: INVALID FORMAT
2010-01-02 18:19:38.871: [ OCRRAW][1]ibctx:1:ERROR: INVALID FORMAT
2010-01-02 18:19:38.871: [ OCRRAW][1]proprinit:problem reading the bootblock or superbloc 22
2010-01-02 18:19:38.872: [ default][1]a_init:7!: Backend init unsuccessful : [22]
2010-01-02 18:19:38.872: [ OCRCONF][1]Exporting OCR data to [OCRUPGRADEFILE]
2010-01-02 18:19:38.872: [ OCRAPI][1]a_init:7!: Backend init unsuccessful : [33]
2010-01-02 18:19:38.872: [ OCRCONF][1]There was no previous version of OCR. error:[PROC-33: Oracle Cluster Registry is not configured]
2010-01-02 18:19:38.878: [ OCRRAW][1]propriogid:1: INVALID FORMAT
2010-01-02 18:19:38.879: [ OCRRAW][1]ibctx:1:ERROR: INVALID FORMAT
2010-01-02 18:19:38.879: [ OCRRAW][1]proprinit:problem reading the bootblock or superbloc 22
2010-01-02 18:19:38.879: [ default][1]a_init:7!: Backend init unsuccessful : [22]
2010-01-02 18:19:38.885: [ OCRRAW][1]propriogid:1: INVALID FORMAT
2010-01-02 18:19:38.887: [ OCRRAW][1]ibctx:1:ERROR: INVALID FORMAT
2010-01-02 18:19:38.887: [ OCRRAW][1]proprinit:problem reading the bootblock or superbloc 22
2010-01-02 18:19:38.892: [ OCRRAW][1]propriogid:1: INVALID FORMAT
2010-01-02 18:19:38.902: [ OCRRAW][1]propriowv: Vote information on disk 0 [dev/rdsk/c2t1d0s2] is adjusted from [0/0] to [2/2]
2010-01-02 18:19:38.934: [ OCRRAW][1]propriniconfig:No 92 configuration
2010-01-02 18:19:38.934: [ OCRAPI][1]a_init:6a: Backend init successful
2010-01-02 18:19:39.123: [ OCRCONF][1]Initialized DATABASE keys in OCR
2010-01-02 18:19:39.163: [ OCRCONF][1]csetskgfrblock0: clsfmt returned with error [4].
2010-01-02 18:19:39.163: [ OCRCONF][1]Failure in setting block0 [-1]
2010-01-02 18:19:39.163: [ OCRCONF][1]OCR block 0 is not set !
2010-01-02 18:19:39.163: [ OCRCONF][1]Exiting [status=failed]...

Similar Messages

When trying to install itunes and i get a error that says there is a problem with this windos installer package. a prodram required for this install to complete could not be run. contact you support personnel or package vendor

when trying to install itunes and i get a error that says there is a problem with this windos installer package. a prodram required for this install to complete could not be run. contact you support personnel or package vendor

I have the same problem

When I run the Receiving interface i get an error that the period is not open. But all periods are open from Jun 14 through April 15.

I am running the following inserts and all periods are open but I still get this error in the po_interface_errors table.
"Error: Please enter a GL Date within an open inventory accounting period.
Cause:        You provided a GL date that is not within an open inventory accounting period.
Action:        Enter a date that is within an open period."
Here are the inserts.
INSERT INTO rcv_headers_interface
(header_interface_id, GROUP_ID, processing_status_code,
receipt_source_code, transaction_type, last_update_date,
last_updated_by, last_update_login, creation_date, created_by,
vendor_id,expected_receipt_date, validation_flag)
SELECT rcv_headers_interface_s.NEXTVAL, rcv_interface_groups_s.NEXTVAL,
'PENDING', 'VENDOR', v_transaction_type , SYSDATE, v_user_id, 0,SYSDATE, v_user_id,
v_vendor_id, SYSDATE, 'Y'
FROM DUAL;
INSERT INTO rcv_transactions_interface
(interface_transaction_id, GROUP_ID,
last_update_date, last_updated_by, creation_date,
created_by, last_update_login, transaction_type,
transaction_date, processing_status_code,
processing_mode_code, transaction_status_code,
po_header_id, po_line_id, item_id, quantity, unit_of_measure,
po_line_location_id, auto_transact_code,
receipt_source_code, to_organization_code,
source_document_code, document_num,
destination_type_code,
deliver_to_location_id,subinventory,
header_interface_id, validation_flag)
SELECT rcv_transactions_interface_s.NEXTVAL,
rcv_interface_groups_s.CURRVAL, SYSDATE, v_user_id,
SYSDATE, v_user_id, 0, 'RECEIVE', SYSDATE, 'PENDING',
'BATCH', 'PENDING', v_po_header_id,v_po_line_id,
v_item_id, v_quantity,
v_unit_meas_lookup_code,
v_line_location_id, 'DELIVER', 'VENDOR',
v_organization_code, 'PO', v_po_number,
v_destination_type_code,
v_deliver_to_location_id, v_destination_subinventory,
rcv_headers_interface_s.CURRVAL, 'Y'
FROM DUAL;

I went to Inventory > Setup > Organizations
but I do not see a place to open a period under an organization. If there is another place to go let me know.
I looked under calendars but that does not have anything to do with periods as far as I can tell.

I'm running snow leopard. The try to open any .mov file in Quicktime, and I get an error message that says, "The document xyz.mov could not be opened. The movie is not in a format that Quicktime player understands. I'm a recent upgrade to Snow Leopard.

I'm running snow leopard. The try to open any .mov file in Quicktime, and I get an error message that says, "The document xyz.mov could not be opened. The movie is not in a format that Quicktime player understands. I'm a recent upgrade to Snow Leopard.
Help!
Thanks, Mark

Unfortunately, the error message gives no details about what codec might be missing or what it needs.
If the file can't be opened in QT, it only means you cannot use the QT "Inspector" window to check what compression formats were used to create the file. It does not mean you can't use the Finder "Information" window to check on the compression formats or use a third party media information window (e.g., like VLC which will open many compression formats not supported natively by QT) to determine what kind of data is included in the MOV wrapper. If the file cannot be opened in any app, it is usually a good sign that the file itself is corrupted.
It's a stupid error message. Apple should do better than that.
Error trapping is quite extensive but there are still many areas which require human oversight. The message is telling you that either the container has a problem (e.g., not properly terminated, non-standard, or corrupted) or that one or more of the compression formats used is not supported by your current codec component configuration or that the data was encoded using non-standard settings or preferences not supported by QT or that the fourCC code does not match the data contained in the file or that there are timecode inconsistencies, etc., etc., etc. In short there are a near infinite number of possible problems for which it would be very difficult/nearly impossible to program error trapping depending on your sourcing of content and how you process it before it reaches the player app. Think of it like trying to play a BD disc in an DVD player.
I'll call Apple support when I get a chance.
Chances are good that they will end up sending you back here. In any case, it is often a good idea to post a sample file for examination by other QT users. At the very least, they should be able to tell you if the sample file will play on other systems which would indicate whether or not the file itself is bad and under the best of circumstances whould allow them to examing the file in detail for various common problems.

I am having trouble dating to version 3.6.14. I am running Linux/Ubutu OS and I get this error message:/tmp/p7x3vko2.part could not be saved, because the source file could not be read. Please help. Thank you , Deb

I am having trouble dating to version 3.6.14 or updating to the Beta testing. I am running Linux/Ubutu OS and I get this error message:/tmp/p7x3vko2.part could not be saved, because the source file could not be read. Please help. Thank you , Deb

Solved for me.
I set the owner/permissions of my profile's mozilla folder's (and all the files in it) to read/write access, and the problem disappeared.
in linux:''
* cd /home/myusername/.mozilla
* chown -cR myusername:mygroup ./
* chmod -cR +rw ./
'''Never do that with root privs (nor with sudo)'''

When i try to run Dreamweaver CC i always get an error.

When i try to run Dreamweaver CC i always get an error on : ?PeekUTF32@WREncodingMap@@QEBPBIXZ.
This started after i switch the WRServices.dll, when i was getting one other error.
And no one answered me on the phone service.

First, ask in that forum Dreamweaver support forum
The Cloud forum is not about using individual programs
The Cloud forum is about the Cloud as a delivery & install process
If you will start at the Forums Index https://forums.adobe.com/welcome
You will be able to select a forum for the specific Adobe product(s) you use
Click the "down arrow" symbol on the right (where it says All communities) to open the drop down list and scroll
Second, consider UN-installing and running the cleaner and RE-installing if the other Dreamweaver users think your install is corrupted
Discussions of RE-installing
-http://forums.adobe.com/thread/1408331?tstart=0
-http://forums.adobe.com/thread/1398961?tstart=0
-and http://helpx.adobe.com/creative-cloud/help/install-apps.html
-using the cleaner after uninstalling and before reinstalling will usually help
-http://helpx.adobe.com/creative-suite/kb/cs5-cleaner-tool-installation-problems.html

When I try to launch terminal, i get an error "You are not authorized to run this applicationThe administrator has set your shell to an illegal value."

When I try to launch terminal, i get an error "You are not authorized to run this applicationThe administrator has set your shell to an illegal value."

If you'd asked a question in your original post it might have solicited more pertinent responses. As it is, you were stating a fact. No one knew whether you considered that fact a problem, or what you were hoping to gain by doing so.
The simple addition of 'can anyone help me fix this so I can run Terminal' would have counted for a lot.
As it is, your solution is likely to require the Terminal, so you're going to need to fix that one way or another. The simplest would be to create a new admin account (System Preferences -> Users & Groups) then log in using that account.
Then try and launch the terminal. If that works the problem is specific to your original account and can likely be fixed via some command-line tweaking. I'd start with:
dscl . read /Users/<username>
(where <username> is the short name of the account having a problem). This will show the records in the directory data for your account, one of which will be UserShell. Chances are that value is invalid, or missing, and can be corrected via:
sudo dscl . -change /Users/<username> UserShell <currentValue> /bin/bash
(where <currentValue) is the current setting for UserShell) which will change the user's shell to /bin/bash (the default).
Of course, you might already know this and already tried, but since you didn't say so in your original post it's worth checking.

I downloaded the latest version and I get this error when I open it. Problem signature:   Problem Event Name:     InPageError   Error Status Code:     c0000185   Faulting Media Type:     00000003   OS Version:     6.1.7601.2.1.0.768.3. Any clue why or how

I downloaded the latest version and I get this error when I open it. Problem signature:   Problem Event Name:
InPageError   Error Status Code:
c0000185   Faulting Media Type:
00000003   OS Version:
6.1.7601.2.1.0.768.3. Any clue why or how to fix?

InPageError
That one's consistent with disk/file damage. The first thing I'd try with that is running a disk check (chkdsk) over your C drive.
XP instructions in the following document: How to perform disk error checking in Windows XP
Vista instructions in the following document: Check your hard disk for errors
Windows 7 instructions in the following document: How to use CHKDSK (Check Disk)
Select both Automatically fix file system errors and Scan for and attempt recovery of bad sectors, or use chkdsk /r (depending on which way you decide to go about doing this). You'll almost certainly have to schedule the chkdsk to run on startup. The scan should take quite a while ... if it quits after a few minutes or seconds, something's interfering with the scan.
Does the chkdsk find/repair any damage? If so, can you get itunes to launch properly afterwards?

When updating to itune 10.5 I get this error message ,older version of bonjour can not be removed, and older version of apple mobile support cannot be removed, any one know how to fix this.

When updating to itune 10.5 I get this error message ,older version of bonjour can not be removed, and older version of apple mobile support cannot be removed, any one know how to fix this.

1) The older version of Bonjour can not be removed. Contact your technical support group.
Unfortunately, this sort of trouble has gotten more complicated to deal with ever since Microsoft pulled the Windows Installer CleanUp utility from their Download Center on June 25. First we have to find a copy of the utility.
Let's try Googling. (Best not to use Bing, I think.) Look for a working download site for at least version 3.0 of the Windows Installer CleanUp utility. After downloading the utility installer file (msicuu2.exe), scan the file for malware, just in case. (I use the free version of Malwarebytes AntiMalware to do single-file scans for that.)
If the file is clean, to install the utility, doubleclick the msicuu2.exe file you've downloaded.
Now run the utility ("Start > All Programs > Windows Install Clean Up"). In the list of programs that appears in CleanUp, select any Bonjour entries and click "Remove".
Quit out of CleanUp, restart the PC and try installing iTunes again. Does the install go through properly now?
(If you do find a clean download site for the correct version of CleanUp, please don't tell me where it is. Without wishing to sound paranoid (although I grant it does sound paranoid), there is a non-zero chance that posting links to download locations for the utility here at Discussions leads to that download location being shut down.)

When I add a Disc Menu I get an error message: "Sorry, a serious problem occurred and Premiere needs to shut dow..." I am using Premiere Elements 10 on a MacbookPro. I have uninstalled and deactivated and reinstalled but still same error.

When I add a Disc Menu I get an error message: "Sorry, a serious problem occurred and Premiere Elements needs to shut dow..." I am using Premiere Elements 10 on a Apple MacbookPro. I have uninstalled and deactivated and reinstalled but still get same error.

cyclone
What video card/graphics card does your Mac computer use? NVIDIA GeForce? If so, please read the description and solution for the Premiere Elements/NVIDIA GeForce issue in the Announcement on the matter at the top of this forum. Any questions or need clarification on that, please do
not hesitate to ask.
What specific disc menu theme or themes are associated with this program failure? What is the exact place where the problem hit..
a. just clicking on Disc Menu header
b. dragging Disc Menu from the display of themes into the Disc Menu area customization screen
c. selecting your menu in the display of choices and then hitting Apply
d. other
Are you running Premiere Elements 10 from a User Account with Administrative Privileges?
Is this a "it worked before but not now" or "it never worked before" type issue.
On the Windows side of things, application of Run As Administrator as well as the User Account with Administrative Privileges has been know
to resolve some of these issues. I am strictly an Elements Windows user. What is the Mac side of the story for Run As Administrator? At any
rate, are your computer permissions in order?
Just to cover all bases, do you have the latest version of QuickTime installed on your computer with Premiere Elements 10?
Let us start here and then decide what next.
Thank you.
ATR

I got CRS-4402 error when I run root.sh

Hi all,
I am installing Grid Infrastructure in my new environment, and I have a problem when I run root.sh.
In the first node, root.sh was OK, but I got a CRS-4402 error in the anothers two nodes:
"...CRS-4402: The CSS daemon was started in exclusive mode but found an active CSS daemon on node
brloulsrac01, number 1, and is terminating
An active cluster was found during exclusive startup, restarting to join the cluster..."
Please, can anybody help me?
Thanks in advance.
Leonardo.

*Grid Infrastructure 11.2.0.2 Installation or Upgrade may fail due to Multicasting Requirement [ID 1212703.1]*
This note does not apply to 11.2.0.3 GI installations, and I am installing 11.2.0.3 GI .
===================================================================================================
*Clusterware Not Starting On Newly Added RAC Node [ID 1270208.1]*
I don't see any problem in this setup...
[root@brloulsrac01 /]# /u01/11.2.0/grid/bin/oifcfg getif
eth2 7.9.8.0 global public
eth3 172.30.2.0 global cluster_interconnect
[root@brloulsrac01 /]# /u01/11.2.0/grid/bin/oifcfg iflist
eth2 7.9.8.0
eth3 172.30.2.0
eth3 169.254.0.0
[root@brloulsrac02 oraInventory]# /u01/11.2.0/grid/bin/oifcfg getif
PRIF-10: failed to initialize the cluster registry
[root@brloulsrac02 oraInventory]# /u01/11.2.0/grid/bin/oifcfg iflist
eth2 7.9.8.0
eth3 172.30.2.0
[root@brloulsrac03 oraInventory]# /u01/11.2.0/grid/bin/oifcfg getif
PRIF-10: failed to initialize the cluster registry
[root@brloulsrac03 oraInventory]# /u01/11.2.0/grid/bin/oifcfg iflist
eth2 7.9.8.0
eth3 172.30.2.0
====================================================================================================
[grid@brloulsrac01 ~]$ /u01/11.2.0/grid/bin/cluvfy stage -pre crsinst -n brloulsrac02 -verbose
Performing pre-checks for cluster services setup
Checking node reachability...
Check: Node reachability from node "brloulsrac01"
Destination Node Reachable?
brloulsrac02 yes
Result: Node reachability check passed from node "brloulsrac01"
Checking user equivalence...
Check: User equivalence for user "grid"
Node Name Status
brloulsrac02 passed
Result: User equivalence check passed for user "grid"
Checking node connectivity...
Checking hosts config file...
Node Name Status
brloulsrac02 passed
Verification of the hosts config file successful
Interface information for node "brloulsrac02"
Name IP Address Subnet Gateway Def. Gateway HW Address MTU
eth2 7.9.10.216 7.9.8.0 0.0.0.0 7.9.8.2 44:1E:A1:4A:75:20 1500
eth3 172.30.2.3 172.30.2.0 0.0.0.0 7.9.8.2 44:1E:A1:4A:75:24 9000
Check: Node connectivity of subnet "7.9.8.0"
Result: Node connectivity passed for subnet "7.9.8.0" with node(s) brloulsrac02
Check: TCP connectivity of subnet "7.9.8.0"
Source Destination Connected?
brloulsrac01:7.9.10.215 brloulsrac02:7.9.10.216 passed
Result: TCP connectivity check passed for subnet "7.9.8.0"
Check: Node connectivity of subnet "172.30.2.0"
Result: Node connectivity passed for subnet "172.30.2.0" with node(s) brloulsrac02
Check: TCP connectivity of subnet "172.30.2.0"
Source Destination Connected?
brloulsrac01:7.9.10.215 brloulsrac02:172.30.2.3 passed
Result: TCP connectivity check passed for subnet "172.30.2.0"
Interfaces found on subnet "7.9.8.0" that are likely candidates for VIP are:
brloulsrac02 eth2:7.9.10.216
Interfaces found on subnet "172.30.2.0" that are likely candidates for a private interconnect are:
brloulsrac02 eth3:172.30.2.3
Result: Node connectivity check passed
Checking multicast communication...
Checking subnet "7.9.8.0" for multicast communication with multicast group "230.0.1.0"...
Check of subnet "7.9.8.0" for multicast communication with multicast group "230.0.1.0" passed.
Checking subnet "172.30.2.0" for multicast communication with multicast group "230.0.1.0"...
Check of subnet "172.30.2.0" for multicast communication with multicast group "230.0.1.0" passed.
Check of multicast communication passed.
Checking ASMLib configuration.
Node Name Status
brloulsrac02 passed
Result: Check for ASMLib configuration passed.
Check: Total memory
Node Name Available Required Status
brloulsrac02 78.6334GB (8.2453084E7KB) 1.5GB (1572864.0KB) passed
Result: Total memory check passed
Check: Available memory
Node Name Available Required Status
brloulsrac02 78.0306GB (8.1821012E7KB) 50MB (51200.0KB) passed
Result: Available memory check passed
Check: Swap space
Node Name Available Required Status
brloulsrac02 32GB (3.3554424E7KB) 16GB (1.6777216E7KB) passed
Result: Swap space check passed
Check: Free disk space for "brloulsrac02:/u01/11.2.0/grid"
Path Node Name Mount point Available Required Status
/u01/11.2.0/grid brloulsrac02 /u01 44.9492GB 5.5GB passed
Result: Free disk space check passed for "brloulsrac02:/u01/11.2.0/grid"
Check: Free disk space for "brloulsrac02:/tmp"
Path Node Name Mount point Available Required Status
/tmp brloulsrac02 /tmp 2.293GB 1GB passed
Result: Free disk space check passed for "brloulsrac02:/tmp"
Check: User existence for "grid"
Node Name Status Comment
brloulsrac02 passed exists(502)
Checking for multiple users with UID value 502
Result: Check for multiple users with UID value 502 passed
Result: User existence check passed for "grid"
Check: Group existence for "oinstall"
Node Name Status Comment
brloulsrac02 failed does not exist
Result: Group existence check failed for "oinstall"
Check: Group existence for "dba"
Node Name Status Comment
brloulsrac02 passed exists
Result: Group existence check passed for "dba"
Check: Membership of user "grid" in group "oinstall" [as Primary]
Node Name User Exists Group Exists User in Group Primary Status
brloulsrac02 yes yes no N/A failed
Result: Membership check for user "grid" in group "oinstall" [as Primary] failed
Check: Membership of user "grid" in group "dba"
Node Name User Exists Group Exists User in Group Status
brloulsrac02 yes yes yes passed
Result: Membership check for user "grid" in group "dba" passed
Check: Run level
Node Name run level Required Status
brloulsrac02 3 3,5 passed
Result: Run level check passed
Check: Hard limits for "maximum open file descriptors"
Node Name Type Available Required Status
brloulsrac02 hard 65536 65536 passed
Result: Hard limits check passed for "maximum open file descriptors"
Check: Soft limits for "maximum open file descriptors"
Node Name Type Available Required Status
brloulsrac02 soft 1024 1024 passed
Result: Soft limits check passed for "maximum open file descriptors"
Check: Hard limits for "maximum user processes"
Node Name Type Available Required Status
brloulsrac02 hard 16384 16384 passed
Result: Hard limits check passed for "maximum user processes"
Check: Soft limits for "maximum user processes"
Node Name Type Available Required Status
brloulsrac02 soft 2047 2047 passed
Result: Soft limits check passed for "maximum user processes"
Check: System architecture
Node Name Available Required Status
brloulsrac02 x86_64 x86_64 passed
Result: System architecture check passed
Check: Kernel version
Node Name Available Required Status
brloulsrac02 2.6.18-274.el5 2.6.18 passed
Result: Kernel version check passed
Check: Kernel parameter for "semmsl"
Node Name Current Configured Required Status Comment
brloulsrac02 250 250 250 passed
Result: Kernel parameter check passed for "semmsl"
Check: Kernel parameter for "semmns"
Node Name Current Configured Required Status Comment
brloulsrac02 32000 32000 32000 passed
Result: Kernel parameter check passed for "semmns"
Check: Kernel parameter for "semopm"
Node Name Current Configured Required Status Comment
brloulsrac02 100 100 100 passed
Result: Kernel parameter check passed for "semopm"
Check: Kernel parameter for "semmni"
Node Name Current Configured Required Status Comment
brloulsrac02 142 142 128 passed
Result: Kernel parameter check passed for "semmni"
Check: Kernel parameter for "shmmax"
Node Name Current Configured Required Status Comment
brloulsrac02 68719476736 68719476736 4294967295 passed
Result: Kernel parameter check passed for "shmmax"
Check: Kernel parameter for "shmmni"
Node Name Current Configured Required Status Comment
brloulsrac02 4096 4096 4096 passed
Result: Kernel parameter check passed for "shmmni"
Check: Kernel parameter for "shmall"
Node Name Current Configured Required Status Comment
brloulsrac02 4294967296 4294967296 2097152 passed
Result: Kernel parameter check passed for "shmall"
Check: Kernel parameter for "file-max"
Node Name Current Configured Required Status Comment
brloulsrac02 6815744 6815744 6815744 passed
Result: Kernel parameter check passed for "file-max"
Check: Kernel parameter for "ip_local_port_range"
Node Name Current Configured Required Status Comment
brloulsrac02 between 9000.0 & 65500.0 between 9000.0 & 65500.0 between 9000.0 & 65500.0 passed
Result: Kernel parameter check passed for "ip_local_port_range"
Check: Kernel parameter for "rmem_default"
Node Name Current Configured Required Status Comment
brloulsrac02 262144 262144 262144 passed
Result: Kernel parameter check passed for "rmem_default"
Check: Kernel parameter for "rmem_max"
Node Name Current Configured Required Status Comment
brloulsrac02 4194304 4194304 4194304 passed
Result: Kernel parameter check passed for "rmem_max"
Check: Kernel parameter for "wmem_default"
Node Name Current Configured Required Status Comment
brloulsrac02 262144 262144 262144 passed
Result: Kernel parameter check passed for "wmem_default"
Check: Kernel parameter for "wmem_max"
Node Name Current Configured Required Status Comment
brloulsrac02 1048576 1048576 1048576 passed
Result: Kernel parameter check passed for "wmem_max"
Check: Kernel parameter for "aio-max-nr"
Node Name Current Configured Required Status Comment
brloulsrac02 3145728 3145728 1048576 passed
Result: Kernel parameter check passed for "aio-max-nr"
Check: Package existence for "make"
Node Name Available Required Status
brloulsrac02 make-3.81-3.el5 make-3.81 passed
Result: Package existence check passed for "make"
Check: Package existence for "binutils"
Node Name Available Required Status
brloulsrac02 binutils-2.17.50.0.6-20.el5 binutils-2.17.50.0.6 passed
Result: Package existence check passed for "binutils"
Check: Package existence for "gcc(x86_64)"
Node Name Available Required Status
brloulsrac02 gcc(x86_64)-4.1.2-52.el5 gcc(x86_64)-4.1.2 passed
Result: Package existence check passed for "gcc(x86_64)"
Check: Package existence for "libaio(x86_64)"
Node Name Available Required Status
brloulsrac02 libaio(x86_64)-0.3.106-5 libaio(x86_64)-0.3.106 passed
Result: Package existence check passed for "libaio(x86_64)"
Check: Package existence for "glibc(x86_64)"
Node Name Available Required Status
brloulsrac02 glibc(x86_64)-2.5-81 glibc(x86_64)-2.5-24 passed
Result: Package existence check passed for "glibc(x86_64)"
Check: Package existence for "compat-libstdc++-33(x86_64)"
Node Name Available Required Status
brloulsrac02 compat-libstdc++-33(x86_64)-3.2.3-61 compat-libstdc++-33(x86_64)-3.2.3 passed
Result: Package existence check passed for "compat-libstdc++-33(x86_64)"
Check: Package existence for "elfutils-libelf(x86_64)"
Node Name Available Required Status
brloulsrac02 elfutils-libelf(x86_64)-0.137-3.el5 elfutils-libelf(x86_64)-0.125 passed
Result: Package existence check passed for "elfutils-libelf(x86_64)"
Check: Package existence for "elfutils-libelf-devel"
Node Name Available Required Status
brloulsrac02 elfutils-libelf-devel-0.137-3.el5 elfutils-libelf-devel-0.125 passed
WARNING:
PRVF-7584 : Multiple versions of package "elfutils-libelf-devel" found on node brloulsrac02: elfutils-libelf-devel(i386)-0.137-3.el5,elfutils-libelf-devel(x86_64)-0.137-3.el5
Result: Package existence check passed for "elfutils-libelf-devel"
Check: Package existence for "glibc-common"
Node Name Available Required Status
brloulsrac02 glibc-common-2.5-81 glibc-common-2.5 passed
Result: Package existence check passed for "glibc-common"
Check: Package existence for "glibc-devel(x86_64)"
Node Name Available Required Status
brloulsrac02 glibc-devel(x86_64)-2.5-81 glibc-devel(x86_64)-2.5 passed
Result: Package existence check passed for "glibc-devel(x86_64)"
Check: Package existence for "glibc-headers"
Node Name Available Required Status
brloulsrac02 glibc-headers-2.5-81 glibc-headers-2.5 passed
Result: Package existence check passed for "glibc-headers"
Check: Package existence for "gcc-c++(x86_64)"
Node Name Available Required Status
brloulsrac02 gcc-c++(x86_64)-4.1.2-52.el5 gcc-c++(x86_64)-4.1.2 passed
Result: Package existence check passed for "gcc-c++(x86_64)"
Check: Package existence for "libaio-devel(x86_64)"
Node Name Available Required Status
brloulsrac02 libaio-devel(x86_64)-0.3.106-5 libaio-devel(x86_64)-0.3.106 passed
Result: Package existence check passed for "libaio-devel(x86_64)"
Check: Package existence for "libgcc(x86_64)"
Node Name Available Required Status
brloulsrac02 libgcc(x86_64)-4.1.2-52.el5 libgcc(x86_64)-4.1.2 passed
Result: Package existence check passed for "libgcc(x86_64)"
Check: Package existence for "libstdc++(x86_64)"
Node Name Available Required Status
brloulsrac02 libstdc++(x86_64)-4.1.2-52.el5 libstdc++(x86_64)-4.1.2 passed
Result: Package existence check passed for "libstdc++(x86_64)"
Check: Package existence for "libstdc++-devel(x86_64)"
Node Name Available Required Status
brloulsrac02 libstdc++-devel(x86_64)-4.1.2-52.el5 libstdc++-devel(x86_64)-4.1.2 passed
Result: Package existence check passed for "libstdc++-devel(x86_64)"
Check: Package existence for "sysstat"
Node Name Available Required Status
brloulsrac02 sysstat-7.0.2-11.el5 sysstat-7.0.2 passed
Result: Package existence check passed for "sysstat"
Check: Package existence for "ksh"
Node Name Available Required Status
brloulsrac02 ksh-20100621-5.el5 ksh-20060214 passed
Result: Package existence check passed for "ksh"
Checking for multiple users with UID value 0
Result: Check for multiple users with UID value 0 passed
Check: Current group ID
Result: Current group ID check passed
Starting check for consistency of primary group of root user
Node Name Status
brloulsrac02 passed
Check for consistency of root user's primary group passed
Starting Clock synchronization checks using Network Time Protocol(NTP)...
NTP Configuration file check started...
The NTP configuration file "/etc/ntp.conf" is available on all nodes
NTP Configuration file check passed
Checking daemon liveness...
Check: Liveness for "ntpd"
Node Name Running?
brloulsrac02 yes
Result: Liveness check passed for "ntpd"
Check for NTP daemon or service alive passed on all nodes
Checking NTP daemon command line for slewing option "-x"
Check: NTP daemon command line
Node Name Slewing Option Set?
brloulsrac02 yes
Result:
NTP daemon slewing option check passed
Checking NTP daemon's boot time configuration, in file "/etc/sysconfig/ntpd", for slewing option "-x"
Check: NTP daemon's boot time configuration
Node Name Slewing Option Set?
brloulsrac02 yes
Result:
NTP daemon's boot time configuration check for slewing option passed
Checking whether NTP daemon or service is using UDP port 123 on all nodes
Check for NTP daemon or service using UDP port 123
Node Name Port Open?
brloulsrac02 yes
NTP common Time Server Check started...
NTP Time Server "10.35.100.100" is common to all nodes on which the NTP daemon is running
NTP Time Server ".LOCL." is common to all nodes on which the NTP daemon is running
Check of common NTP Time Server passed
Clock time offset check from NTP Time Server started...
Checking on nodes "[brloulsrac02]"...
Check: Clock time offset from NTP Time Server
Time Server: 10.35.100.100
Time Offset Limit: 1000.0 msecs
Node Name Time Offset Status
brloulsrac02 -0.569 passed
Time Server "10.35.100.100" has time offsets that are within permissible limits for nodes "[brloulsrac02]".
Time Server: .LOCL.
Time Offset Limit: 1000.0 msecs
Node Name Time Offset Status
brloulsrac02 0.0 passed
Time Server ".LOCL." has time offsets that are within permissible limits for nodes "[brloulsrac02]".
Clock time offset check passed
Result: Clock synchronization check using Network Time Protocol(NTP) passed
Checking Core file name pattern consistency...
Core file name pattern consistency check passed.
Checking to make sure user "grid" is not in "root" group
Node Name Status Comment
brloulsrac02 passed does not exist
Result: User "grid" is not part of "root" group. Check passed
Check default user file creation mask
Node Name Available Required Comment
brloulsrac02 0022 0022 passed
Result: Default user file creation mask check passed
Checking consistency of file "/etc/resolv.conf" across nodes
Checking the file "/etc/resolv.conf" to make sure only one of domain and search entries is defined
File "/etc/resolv.conf" does not have both domain and search entries defined
Checking if domain entry in file "/etc/resolv.conf" is consistent across the nodes...
domain entry in file "/etc/resolv.conf" is consistent across nodes
Checking if search entry in file "/etc/resolv.conf" is consistent across the nodes...
search entry in file "/etc/resolv.conf" is consistent across nodes
Checking file "/etc/resolv.conf" to make sure that only one search entry is defined
All nodes have one search entry defined in file "/etc/resolv.conf"
Checking DNS response time for an unreachable node
Node Name Status
brloulsrac02 passed
The DNS response time for an unreachable node is within acceptable limit on all nodes
File "/etc/resolv.conf" is consistent across nodes
Check: Time zone consistency
Result: Time zone consistency check passed
Pre-check for cluster services setup was unsuccessful on all the nodes.

When I run the Ipod Updater I get the message Error in service

My 5g Ipod is not recognized and when I run the updater it shows the message Error in Service. Please help

Not sure....Have you tried resetting the iPod and trying it again. Almost sounds like the software issue, but not totally sure. If you haven't tried resetting your iPod, try that and see what you get! If you don't know how to reset your iPod just press and hold the middle button and the menu button. Your iPod will turn off, and reboot

When I run Verify Disk Permissions I get something that can not be repaired.

When I run Verify Disk Permissions I get something that can not be repaired. The message I get is
Permissions differ on “Applications/Safari.app/Contents/Resources/Safari.help/Contents/Resources/inde x.html”; should be lrwxr-xr-x ; they are -rwxr-xr-x .
When I run a repair disk permissions it does not get rid of this.
Any ideas?
Thanks in advance.

aquilafisher --
I would recommend that you don't waste your time with "Verify." Go straight to "Repair Permissions."
The chances are excellent that you will get that one advisory, and at the end it will say "Repair Permissions Completed."
There are lots of those notations that will seem to us everyday users as an "error." But it's just noted changes.
If after running "Repair" it says "Repair Permissions Could Not be Completed," that's the only time you ned to worry.
And, I totally agree with what Niel said. Sorry, did not see his reply when I poster.

I have a wireless network at home. I run my iphone and ipad on it with no problems. Just purchased a MacBook Pro, and now my wi-fi keeps disconnecting and i get an error message saying another device is using the same IP address. What does all this mean?

I have a wireless network at home. I run my iphone and ipad on it with no problems. Just purchased a MacBook Pro, and now my wi-fi keeps disconnecting and i get an error message saying another device is using the same IP address. What does all this mean?

Hello AKCamus
To give you some ideas of what to do next, I have provided a few articles that will give some troubleshooting Wi-Fi connections and recommended Wi-Fi settings.
iOS and OS X: Recommended settings for Wi-Fi routers and access points
http://support.apple.com/kb/HT4199
iOS: Troubleshooting Wi-Fi networks and connections
http://support.apple.com/kb/ts1398
Troubleshooting Wi-Fi issues in OS X Lion and Mac OS X v10.6
http://support.apple.com/kb/HT4628
Thanks for using Apple Support Communities.
Regards,
-Norm G.

Itunes stops working and I get an error message "APPCRASH" when I try to play a downloaded TV show. I have udated Itunes and removed and reinstalled quicktime.

When I try to play a downloaded TV show, itunes stops working and I get a error message "APPCRASH". I have updated itunes and removed and reinstalled quicktime.

Open your QuickTime control panel (either via the Control panels, or by going "Edit > Preferences > QuickTime Preferences" in the Quicktime Player). In the Advanced tab, uncheck Enable Direct3D video acceleration:
... and click OK.
Quit the QuickTime Player if you have it open. Restart the PC and try watching the videos in iTunes again. Do they play now?

When I run root.sh and I get OCR errors

Similar Messages

Maybe you are looking for