When I try to start my macbook it gives an error of Please restart your computer, but when i do this i get the same error.

When I try to start my macbook it gives an error of Please restart your computer, but when i do this i get the same error. This occured after my macbook pro shut down (because of low battery) while it was installing some updates. Please Help?

Try reinstalling OS X. What version did you have installed? If it's Snow Leopard do this:
Reinstall OS X without erasing the drive
Do the following:
1. Repair the Hard Drive and Permissions
Boot from your Snow Leopard Installer disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Utilities menu. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the installer.
If DU reports errors it cannot fix, then you will need Disk Warrior and/or Tech Tool Pro to repair the drive. If you don't have either of them or if neither of them can fix the drive, then you will need to reformat the drive and reinstall OS X.
2. Reinstall Snow Leopard
If the drive is OK then quit DU and return to the installer. Proceed with reinstalling OS X. Note that the Snow Leopard installer will not erase your drive or disturb your files. After installing a fresh copy of OS X the installer will move your Home folder, third-party applications, support items, and network preferences into the newly installed system.
Download and install the Combo Updater for the version you prefer from support.apple.com/downloads/.

Similar Messages

I am unable to use Iboost app, when i try to use it, I get an error "iBoost App is damaged" and reinstall from app store. I get the same error even after installing a fresh copy. Need help to resovle this issue.

“iBoostUp.app” is damaged and can’t be opened. Delete “iBoostUp.app” and download it again from the App Store.
Because of the above error, i am not able to use iboostup application. I have even tried to reinstall from app store, but the issue still continues.
Need help.

Perhaps the damaged file is an auxiliary file outside the app bundle and stored elsewhere on your Mac. Try deleting the app and all it files with an app for that purpose. Afree one is AppCleaner;
http://www.freemacsoft.net/appcleaner/

I downloaded iTunes on my new computer, but when I try to download my already purchased songs a message pops up saying, "Your computer is not authorized." How can I fix this?

I downloaded iTunes on my new computer, but when I try to download my already purchased songs a message pops up saying, "Your computer is not authorized." How can I fix this?

Launch iTunes and click on the click on the store menu item the select authorized this computer.

HT203176 i have a slow macbook, i ran live disk utilities and said I need to repair disk from a cd. did that, I got volume repaired from the external disk. when I reboot from hdd, then run disk utility, I get the same error message i did b4 repair

i have a slow macbook, i ran live disk utilities (from hard drive), turned out I needed to repair disk from a installation disk. Did that, I got the volume (Hard drive) repaired from the installation disk disk. To this point, great!
When I reboot from hdd, then run disk utility, I get the same error message i did b4 repair. I went thru two rounds of this.....
Can anyone help? thanks

Sorry guys, I don't see how to reply to you so I use reply to "me" basically.
So the error I get is "volume header needs minor repair" and then you need to perform repair from the installation disk message.
I did repair not verify from the disk twice. Every time ending in the "the volume had ha been successfully repaired". Then I reboot from the internal disk. Run disk utilities from it, do verify and get the same error message I got before repair. I hope this can shed some light fr you guys. Sorry I didn't include details in the original
MEssage.

I'm getting an error starting Photoshop CS4. Error number 148.3 Licensing for this product has stopped working. I rebooted several times to no avail. Still get the same error message everytime I try to start Photoshop. I'm using Windows 7 -- 64 bit

Error number 148.3 Licensing for this product has stopped working. I rebooted several times to no avail. Still get the same error message everytime I try to start Photoshop. I'm using Windows 7 -- 64 bit

If you can not use CS4 menu Help>Activate|Deactivate to get the install working again you may need to re-install CS4.

I have an older Macbook with OS/X. Tried to download iTunes 10 a few times now, but when installing I always get the same error message: Run Preinstall Script for Apple Mobile Device Support. What can I do to finalise the installation?

I have an older Macbook with OS/X. Tried to download iTunes 10 a few times now, but when installing I always get the same error message: Run Preinstall Script for Apple Mobile Device Support. What can I do to finalise the installation?

Thanks. Short of the sort of "generic" suggestions of restaring your system, if you haven't, and repairing disk permissions and verifying the disk, I don't have any advice right now. I'll do some research and see if I can come across anything. Meanwhile, someone else may have an idea.
Regards.

CS6 on Windows 7 - when I try and send my project to Adobe Link, then to Encore I repeatedly get the error message "Encore has stopped working, windows will close the program". I get the same error message when I try and open Encore on its own. Help wou

Both when I open Encore as a standalone program, and when I try and export my work via Adobe Link to Send to Encore, I get the same error message - "Adobe Encore has stopped working. Windows will close the program. Help would really be appreciated. Thanks.

Now that is impressive Stan, thankyou! So simple ... I don't suppose you know why the "build" button is greyed out do you? Don't worry if you don't have more "magic dust" at your fingertips, I'll re-check my settings again, and again ... Thanks for your help. Doreen.

I was installing a new update on my MacBook Pro. With only 20% left it said "an unknown error had occured, please restart your computer." Now that I've restarted - I can't log in!

Ok, my MacBook haven't had any issues earlier, until today. At first Safari was acting kind of weird in that sense that a lot of letters were missing when you went on certain webpages, so I thought of updating since an alert-window popped up and notified that new updates were ready to be installed. So I opened up App Store through my Applications-folder and selected update.
First it asked if I wanted to connect my Mac to a powersource but since I had charged the battery to 79% I didn't think it was necessary. So I continued, computer restarted and began installing the updates.
Everything went fine until it was approximately three minutes left. An error message popped up and said something like "An unknown error has occured. Please restart your computer and try again". I pressed OK, rebooted my computer and when it asked for my password I typed it in. After I pressed OK, the computer indicated it was the wrong password. I tried multiple times and sometimes with different passwords... so now I can't simply log in! What's the problem?
TL;DR - Updated mac, failed after five minutes and now I can't log back in since "I have the wrong password"

Forgot Your Account Password
For Lion/Mountain Lion
    Boot to the Recovery HD:
Restart the computer and after the chime press and hold down the COMMAND and R keys until the menu screen appears. Alternatively, restart the computer and after the chime press and hold down the OPTION key until the boot manager screen appears. Select the Recovery HD and click on the downward pointing arrow button.
     When the menubar appears select Terminal from the Utilities menu.
     Enter resetpassword at the prompt and press RETURN. Follow
     instructions in the dialog window that will appear.
     Or see Reset a Mac OS X 10.7 Lion Password and
     OS X Lion- Apple ID can be used to reset your user account password.

Well I was using my iphone 5, When restart and it did not turn on gets stuck in the presentation of apple (the apple) and at the top left of the screen above the apple logo reincia Appears this text, down and then turns back on and i get the same error ,

Well I was using my iphone 5, When restart and it did not turn on gets stuck in the presentation of apple (the apple) and at the top left of the screen above the apple logo reincia Appears this text, down and then turns back on and i get the same error , i try to restore with itunes restore mode and throws me error!, could anyone help? I'm going crazy!. Thank you!
This is the mistake That I get up the logo and then reboots iphone and Continues to Appear;
(NAND) _findflashmediaandkeepout: 601 physical nand block offset 1
(NAND) start: 356 this 0x96959400 PROVIDER = 0x96b1de80 falshmedia = 0x96b1de80
(NAND) WMR_Start: 149 apple PNN NAND Driver, Read / Write
(NAND) WMR_Start: 174 FIL_INT (OK)
(NAND) WMR_open :371 vfl_open (ok)
(NAND) s_cxt_boot:88 sftl: error, unclean shutdown; adopted 7775 spans
(NAND) WMR_open:420 FTL_open (ok)
(NAND)_publishServices:642 FTL capabilities: 0x00000001
(NAND)_ppnvflGetStruct:3469 checking borrowed blocks-count:23 max_count:23
(NAND)_fetchBorrowedList:881 number of borrowed blocks 16

Hi Guys!
I'm German, so my english writing might not be perfect
I had the same Issue on a 5 i bought. Exact same screen and writing. Battery was totally drawn, first thing I had to replace. The screen had been replaced and since then it wouldn't work anymore according to the previous owner.
It took me a couple hours, after recieving a few errors like 4013 it just never completed the restore, got really hot as well. The Flexwire of the Dock Connector seemed damaged, replaced the dock, but that didn't help.
I almost gave up, thought the Logic Board was bad.
BUT! Then i deceided to check if it has anything to do with the Screen assembly, and it did.
Long story short, on mine the front facing camera, and sensor assy were bad.
Anyhow, the phone works ''perfect'' when i leave them unplugged. So I just ordered a new one and we will see if thats the problem or if the damage is in the Logic Board.
If so, i can live without the sensor and front cam.
Just wanted to share, good luck everyone.

I can not open iPhoto. this is the messageShut down and restart your computer, and then open iPhoto again. If the problem persists, try rebuilding your photo library. To do this, quit iPhoto, and then reopen it while keeping the Option and Command ki get.

Shut down and restart your computer, and then open iPhoto again. If the problem persists, try rebuilding your photo library. To do this, quit iPhoto, and then reopen it while keeping the Option and Command keys pressed. You can also try restoring your photo library from a backup.

Before anyone can help, they need information to work with. Basic stuff:
- What version of iPhoto.
- What version of the Operating System.
- Details. What were you doing when the problem arose?
- Did it ever work properly?
- Are there error messages?
- What steps have you tried already to solve the issue.
Anything else you can think of that might allow someone else to understand your issue.
With this kind of information somebody can develop a starting point for troubleshooting the issue.
Posts that consist of "iPhoto doesn't work. Help" or "iPhoto won't print" or "Suddenly I have no photos!!!!!!!!!!" mean that any helper is simply guessing. With information, s/he may be able to get your issue resolved sooner.

My iTunes will not start. The box on the error message APSDaemon.exe, And message says "This application failed to start because MSVC80.dll was not found. Reinstalling may fix." I did the reinstall and I get the same error.

My iTunes will not start. The box on the error message APSDaemon.exe, And message says "This application failed to start because MSVC80.dll was not found. Reinstalling may fix." I did the reinstall and I get the same error. The error first happened after I approved the an iTurns update.

Same problem today. Took five times to reinstall without any error messages. Apple has posted a way to fix and you should follow their's first. I finally got to upldate correctly by doing their fix but with one difference. I did the following:
1) Went to the C:\program files (x86)\iTunes and C:\program files\iTunes folders and moved every file ending in .dll to the desktop (even if two files in same location had the same name, just replace)
2) Restarted computer and still got error message
3) Uninstalled all apple programs possible in the following order......itunes, apples software update, apple mobile device support, bonjour, and apple application support.....all performed using the microsoft control panel
4) put all the .dll files on the desktop in the trash and emptied (this is a step apple support did not specifically put in their fix but for a final try I wanted to delete everything apple).
5) Restarted computer.
6) Re-installed itunes from apple website
No error messages during re-install and was able to open shortcut in one try. Even updated my ipad to make sure everything was working.

I can't Start, Uninstall or Install new iTunes. I'm getting the same error message: Window Installer Service could not be accessed. No other programs have similar problem. Any suggestion what can be done?

I can't Start, Uninstall of Install new iTunes. I'm getting the same error message: "Window Installer Service could not be accessed". No other programs having similar problem. Any suggestions how to fix it?

For general advice see Troubleshooting issues with iTunes for Windows updates.
The steps in the second box are a guide to removing everything related to iTunes and then rebuilding it which is often a good starting point unless the symptoms indicate a more specific approach. Review the other boxes and the list of support documents further down the page in case one of them applies.
The further information area has direct links to the current and recent builds in case you have problems downloading, need to revert to an older version or want to try the iTunes for Windows (64-bit - for older video cards) (not for XP) release as a workaround for installation or performance issues, or compatibility with QuickTime or third party software.
Your library should be unaffected by these steps but there are also links to backup and recovery advice should it be needed.
tt2

HT1645 whether i use a DL DVD or just a DVD R, it tells me there was an error during multiplexing. I have tried changing every setting, best performance, professional quality, etc. and still get the same error message every time i try to burn to dvd.

whether i use a DL DVD or just a DVD R, it tells me there was an error during multiplexing. I have tried changing every setting, best performance, professional quality, etc. and still get the same error message every time i try to burn to dvd.

Welcome to the forums.
Looks like that error message does refer to encoding (see http://support.apple.com/kb/HT1645) but a problem could be that your video has to be reloaded into iDVD if you started the encoding process and then switched settings. You could start a new iDVD project, or try deleting encoded assets.
Let's start from the beginning -- what length of video are you trying to fit on the DVD? (this will indicate what encoding options you have). Double layer DVDs can be finicky and are used for video more than 2 hrs long.
Use good quality media -- Verbatim is often recommended around here, and I've used Sony DVD-R with good results.
For a detailed treatise, see: https://discussions.apple.com/thread/3926901?tstart=0
John

I was exporting one of my iMovie projects, and then iMovie suddenly froze. I restarted my computer but when I opened iMovie my project wasn't there anymore. I don't have time machine is there a way to get my project back? PLEASE HELP

I was exporting one of my iMovie projects, and then iMovie suddenly froze. I restarted my computer but when I opened iMovie my project wasn't there anymore. I don't have time machine is there a way to get my project back? PLEASE HELP

If the system just Restarted on it's own, Shut down while you were working on something then started back up all those changes, edits, you had done in that app, document, are gone.

I cannot open iphoto- the message I am getting says Shut down and restart your computer, and then open iPhoto again. If the problem persists, try rebuilding your photo library. To do this, quit iPhoto, and then reopen it while keeping the Option and Comma

i cannot open iphoto- the message I am getting says Shut down and restart your computer, and then open iPhoto again. If the problem persists, try rebuilding your photo library. To do this, quit iPhoto, and then reopen it while keeping the Option and Command-
I tries and it doesnt work!!

What version of iPhoto? Assuming 09 or later:
Option 1
Back Up and try rebuild the library: hold down the command and option (or alt) keys while launching iPhoto. Use the resulting dialogue to rebuild. Choose to Repair Database. If that doesn't help, then try again, this time using Rebuild Database.
If that fails:
Option 2
Download iPhoto Library Manager and use its rebuild function. (In early versions of Library Manager it's the File -> Rebuild command. In later versions it's under the Library menu.)
This will create an entirely new library. It will then copy (or try to) your photos and all the associated metadata and versions to this new Library, and arrange it as close as it can to what you had in the damaged Library. It does this based on information it finds in the iPhoto sharing mechanism - but that means that things not shared won't be there, so no slideshows, books or calendars, for instance - but it should get all your events, albums and keywords, faces and places back.
Because this process creates an entirely new library and leaves your old one untouched, it is non-destructive, and if you're not happy with the results you can simply return to your old one.
Regards
TD

When I try to start my macbook it gives an error of Please restart your computer, but when i do this i get the same error.

Similar Messages

Maybe you are looking for