When in transport, which is better have the MBP shut down or sleep mode?

when in transport, which is better have the MBP shut down or in sleep mode?

Read the user manual that came w/your computer.  Personally, I shut down when transporting.  
It all comes down to personal preference.  "Different Strokes For Different Folks"

Similar Messages

  • What is better for a MBP, shut down or sleep?? when you go to bed.

    hi everyone, my question is, what is better for a MBP, to shut it down o sleep, i undestand to pun it into sleep when you go out for a time, or you need to move, but what shoul i do when i go to bed and the mac won´t be use for about 8 hours.
    thanks regards

    If you don't have any documents or programs open that need to stay open for the night then give your Mac a rest and Shut it down.
    If you're updating or have stuff loaded that you want to start back on right in the morning, you could just put it to sleep so you're all set for the morning(make sure you plug it in though). It's personal preference really.

  • MBP shuts down after sleep when 2% battery left

    Sorry guys if u find it irritating to see the similar question again n again but i couldnt stop myself from asking this...
              i have my mbp just 3 weeks old and i tried to callibrate the battery just few hrs ago...i continuously used my mbp until the battery level reached to 2% (the warning message showed when it was 6%)...just then i had to received a phone call. When i was busy talking, i noticed that the mbp has gone to sleep mode...but when i returned (2-3 mins later), i found it shut down...
              well, i think it should have remained to sleep mode but it didnt...then after an hour i connected the power cord and switched on and noticed a progress bar which i saw for the first time....i have been charging it for 40-50 mins, now...
              also the health of my battery keeps fluctuating between 95-100 %...istat shows this...is this normal???
              So what i want to know is, Is this normal for mbp to shut down when the battery reach that low?? OR there is some problem in my MBP???
    if there is should i be going to my mbp reseller shop for service or it is something i can handle myself????
    thanks in advance..

    then how am i supposed to callibrate if it shuts down before completely draining the battery???
    and what about the battery health % being fluctuating? my battery have completed only 9 cycles and the health shown at the moment is 97%

  • My MBP shuts down or sleeps (?) when I close the lid

    Hi
    Forgive me if this is a stupid question, but I haven't been able to solve it on my own by investigating, asking others og reading this forum.
    My MBP from late 2007 has recently started to shut down/sleep (or maybe even "hibernate" - not sure which is the right term) when I close the lid - meaning that when I open it, it *doesn't wake up automatically* like it used to. *I need to push the "on" button and it takes it a while to start up*. It doesn't start up from scratch; it shows the last screen shaded in a light grey tone - and it's takes quite a few seconds to get ready. As far as I recall, it "woke up" automatically before.
    I haven't changed my preferences - and they are all set to "never", as my MBP is nerly always connected to the adaptor.
    Any clues to what happened and how I can change it? It's really annoying!
    Thanks,
    Carina

    Welcome!
    When my MBP started that same behavior, I found that I had accumulated a huge list of wireless networks on my travels. Reviewing the system log, I found my computer was trying to connect to one, a hotel network to which I had connected weeks before and miles away.
    Here's how I fixed it (I have 10.5.8, not 10.6, but the fix should be the same):
    1) Open System Preferences and select "Network."
    2) Be sure "Airport" is selected in the left side of that preference pane.
    3) Click the "Advanced" button. If the next screen does not have the "Airport" tab selected, select it. There should be a window with a list of networks.
    4) Use the + and - buttons below to remove any networks you have accumulated that are not needed. Example: on mine, I removed all but two networks--our home network and the one at a local museum where I volunteer.
    5) Once you'd cleaned off the list to the bare necessities, uncheck the option labeled, "Remember any network this computer has joined." This will not prevent you from using other networks on later travels but will prevent them building up and creating problems.
    That completely cured my wake-from-sleep problems. and other have said it worked for them, too.

  • Which is better: shutting down, or sleep mode?

    Hi Everyone,
    What is better for the longevity of my computer . . . shutting it down, or putting it in sleep mode? I use my computer throughout the day, so I guess it makes sense to keep it on sleep mode, right? However, I had problems with my screens on a previous apple laptop and someone mentioned that might be because I was putting it in sleep mode all the time. What should I do? Thanks!!!

    There's reason to believe that over the long haul that sleeping is probably better than turning it on and off all the time. But whether you wind up with an extra day, month, or year of use...who knows? More to the point is this: under what circumstances are you unwilling to wait for the computer to restart and log in and under what circumstances are you willing to wait? My answer is simple: I want to open the lid and start using my computer - I don't want to wait 2-3 minutes - and my habit doesn't seem to have hurt longevity much. My old Tangerine iBook is still in use (8 years old now) and my white iBook is also still in use (5 years old) and the current owners of both use them just as I did.

  • OS X Mavericks v10.9.4 Update still does not fix the wifi shut off in sleep mode problem

    OS X Mavericks v10.9.4 Update was supposed to fix the wifi connectivity problem with my iMac. Wifi disconnects in sleep mode and does not connect when awakened.  Must reconnect manually every time. PITA.

    Your observation is correct about wifi disconnection in sleep mode. That is normal, you may want to check to see if your Mac supports Power Nap/is enabled- OS X: About Power Nap
    The reconnect should be automatic within a few seconds.
    Does it happen with multiple wifi networks or just one?
    Have you tried deleting and re-adding the wifi network?

  • Which is better for computer and program... sleep or turn off?

    When not using, which is better for the program, sleep or turn off the computer and any explanations are welcome...

    I advise shutting down rather than sleep. A good shut down often clears up nascent problems, and of course you're saving electricity by not running your machine and also saving those precious MTBF hours on all the mechanical components. Think of the hours it would sleep vs. the number of hours you actually use the machine. Even though sleep consumes less electricity, it still consumes.

  • When playing my music, the iMac shuts down after 5 or 6 songs. How can I lengthen the time?

    When playing my music in I tunes, the iMac shuts down after 5 or 6 songs. How can I set it so it plays until I shut it off manually?

    Never Mind, I figured it out.

  • 2011 MBP shuts down when connected to external display

    I've been using my 2011 15" MBP for about a week now with no problem until today when I tried to connect it to my old 20" cinema display. I have the mini display port hooked up to the dvi adapter and a usb connection hooked up to external keyboard and mouse. Everything works just fine if I keep the lid up on the MBP, but if I shut the lid, the MBP shuts down. Down, not that the big screen goes black & then comes on again. It turns itself off.
    Any way I can avoid a trip to the Apple store? In the past, the "geniuses" knew less about external displays than I did. Is there an issue because of the dual graphics cards?

    no - I realized later that the machine doesn't shut off it just acts like it. The hard drive stops spinning & the screen remains black no matter what I do. This doesn't happen when I just shut the lid & then go back to working on it.
    Then if I shut it again & try to get the monitor to respond, I get a blue screen of death color with a two inch band of blue noise along the left side. Very weird.

  • MBP shuts down when battery at appox. 30%

    Hello,
    I have a 17" MBP 2.33GHz Intel Core 2 Duo.
    Recently (in the last 3-4 days) it has decided to shut down completely when the battery charge falls to around 30%. Prior to these symptoms appearing, it behaved normally with the 'low battery warning' appearing at about 5% and then going to sleep mode as opposed to shutting down.
    I have reset the SMU by removing the adapter, battery and pressing the power button for 5 secs. Unfortunately the symptoms remain. Obviously I cannot re-calibrate the battery as it won't carry on below 30% charge without the MBP shutting down.
    I'll be taking a trip to my local Apple dealer in the next few days but was wondering if anyone else here has any further suggestions I could try.
    Many thanks in advance.
    Da Vinci

    glavender wrote:
    ...Hopefully Apple will do something about this. It doesn't seem right that the battery would fail this early! Especially after spending so much on a computer!
    Umm... of course Apple will do something. I do not understand why you felt you had to add that to your reply. Allow me to explain:
    1. I have AppleCare, therefore if it's a hardware issue then any repair will be carried out without any cost to me.
    2. Apple have introduced a 'battery exchange and extension' program:
    http://www.apple.com/support/macbook_macbookpro/batteryupdate/
    If the battery is at fault, regardless of whether I have AppleCare or not, the battery will be replaced as it falls within the terms of the extension program.
    I have just now reset the PRAM and am running on battery power. I'll know in the next couple of hours whether that has had any effect or not.
    Meantime, if anyone else has any additional suggestions as opposed to 'me too' type replies I would be very grateful.
    Many thanks.
    Da Vinci

  • Is it better for your battery if you let it run down all the way and then charge it? Or to charge it whenever you have the opportunity?  Which is better for the life of the battery?

    I was wondering it the life of the battery would last longer if you let the battery run down all the way and then charge it? Or to charge it whenever you have the opportunity even if it doesn't have a low battery?  Which is better for the life of the battery and prolong the life of the battery?

    I've had a iPhone 4s since March 2012, and it's battery is pretty useless now.  I was using the app Battery Doctor (Battery Saver, Battery Life) by Beijing Kingsoft Internet Security software, which encourages the user to charge more often, whenever battery life drops below 100% full and greater than 20% full, and gives ratings according to the number of full, partial & overcharges done, but I'm concerned that charging like that actually results in worse battery life??
    I now have an new iPhone 5 and don't want the battery to only last as short as the last one did
    Any advice/comments please

  • I am facing a problem while working in Muse... The issue is I cannot delete a page from my plan, when I am trying to delete it showing an error and the application shuts down. I am working on an emergency project which I got to submit it tomorrow I hope y

    I am facing a problem while working in Muse... The issue is I cannot delete a page from my plan, when I am trying to delete it showing an error and the application shuts down. I am working on an emergency project which I got to submit it tomorrow I hope you will find a solution for the same.Help with using Adobe Muse CC

    Thanks,
    I have tried with a new site it's working perfectly.
    See the screenshot of the error.
    Thanks for your support Rohit

  • I'm working on my iMac PowerMac8,2 PowerPC G5 (3.1) 2 GHz machine and have been having problems with the computer shutting down unpredictably. After the problem becoming impossible to work with, I shut the machine down. Now a little better, but reoccuring

    I'm working with my iMac PPC G5, PowerMac8,2, 2 GHz machine running OS X 10.4.11, and was having a problem for a while with the machine shutting down unexpectedly. There was no clear pattern to when it was shutting down as far as I could tell. For a while, it would also not restart when buttoned on.
    I set the machine aside for a while, probably a month or more, and then got it back out after its rustication. It started up and runs significantly better than it had been, but I have noticed it shutting down sometimes now again, though not as frequently as before. Sometimes it runs for a good long time between active work, sleep mode, and active work again. Once in a while it does shut down when no one is working on it (while asleep). But now it always restarts when buttoned on.
    I've done the thorough vacuuming of any dust from the unit vents. I wonder if there's anything else I should try. In most other ways the machine works pretty well and has become the family desktop for basic uses, so I'd like to keep it running if I can. A little frustrating to not be able to upgrade all programs (iTunes) to useable versions, but that's another story....
    I would appreciate any ideas about the shut down problem.
    TCC

    Option 1
    Reset your PRAM.  Press and hold down the Command Option P R keys while starting your computer.  You will hear the startup chime.  continue holding down those keys until you hear the startup chime a second time.  Release the keys.  If the computer restarts, you will need to reset your Date and Time.  It might be time to replace your PRAM battery.  The G5 iMacs require a 3 volt CR2032 lithium watch/camera battery like below:
    http://eshop.macsales.com/item/NewerTech/CR2032/
    You can find these batteries at Walmart, Kmart, Target, most local drugstore chains, for between $3-$5, or at Radio Shack for $12-$20.
    If you have any G5 iMac model EXCEPT the iSight version, you can probably do the battery install yourself.  Watch this video on upgrading your iMac's RAM to show you how to remove the back of your iMac, if you don't already know how:
    http://eshop.macsales.com/installvideos/imac_g5_mem_m/
    While you have the back off, use a can of compressed air to blow the dust out the vents at the bottom of the iMac, the fans, and anywhere else you can.  Also inspect the 28-30 capacitors on the logic board.  Look for dark spots, if they look puffy or swollen, or leaks.
    Option 2
    Reset the SMC by removing all cables (USB, Firewire, Ethernet, Modem, Power cord) from the back of your computer.  Let it sit for one minute.  Press and hold the power on button on the back of the iMac while plugging in the power cord.  Release the power on button.  Count to five, the press the power on button again.
    Option 3
    Place your original, came with the iMac when purchased install disk, into the slot on the iMac, press and hold the C key while pressing the power on button on the back of the computer.  (If you have upgraded your OS from when you purchased your iMac, example your iMac came with OS 10.3 installed, and you're now using OS 10.5, then use the OS 10.5 Retail Install disk that you had used to upgrade your OS instead of the original, came with the iMac disk.) 
    Continue holding the C key until you see the OS starting to load.  DO NOT do an OS installation.  At the top Menu bar, select Utilities or Utility, and pull down to Disk Utility.  On the left side of the window that opens,select your normal OS drive.  Click First Aid at the top middle of the window if it isn't already selected.  Click Repair Disk from the lower right area of the window.  When that is done, click Repair Permissions to the left of the Repair Disk button you clicked earlier.
    When that is done, quit Disk Utility.  From the top Menu bar (I think its under Utilities) select the Start Up Manager, and choose your normal boot volume as the startup disk.  Restart the computer.  If successful, and you've rebooted from your normal startup disk, eject the install DVD/CD, and you're good to go.
    Good luck.

  • Hi All, I recently bought a Mac Book Pro and transferred all my photos from my hard drive onto the Mac. I realised that there were some folders which didn't have the camera information embedded in the files and these files refuse to open on iPhoto. HELP!!

    Hi All, I recently bought a Mac Book Pro and transferred all my photos from my hard drive onto the Mac. I realised that there were some folders which didn't have the camera information embedded in the files and these files refuse to open on iPhoto. I know that the folders that have the problem were not transferred to the hard drive via a photo transfer application (I have a Canon camera) but I simply copied them out of the photo card and onto my old PC.
    Is there some way I can open these pictures on my Mac? They work fine on a PC.

    Thanks for your reply.
    The files don't open in preview either. In preview I get the error message 'The file "xxxx_xxx.jpg" could not be opened. It may be damaged or use a file format that Preview doesn't recognize'. The folders with these un-openable pictures do not even get imported into iPhoto. When I try to import them I get an error message about the files being unreadable.
    The color profile information on the un-openable files is not visible but I see that all the other files from my old drive are RGB.

  • When it will be possible to have the armenian keyboard on the iPad iOS6?

    when it will be possible to have the armenian keyboard on the iPad iOS6?

    Hey Mantas,
    Do not expect that feature any time soon. I do not even see that being a feature this year.
    Considering all that is going on and required to be finished and sorted a lot more is/will need to be done.
    In terms of what you can do I have done things like used the refer a friend form which you can style and use that to send emails out to the needed people. I have submitted multiple web forms with ajax etc as well.
    You have the custom fields for the people and emails (if not you can add them) and you can use those to send emails off to people, you just do not have a workflow so your not pestered with it but the notification message is the one that goes out and can have a template applied.
    So there is a number of things you can do to get that going along those lines. I have done a few variations of this on different sites.
    Warning note though - Ajax submission for custom web forms has a total character limit (all fields) of 1024 characters, which is not a lot.

Maybe you are looking for

  • Order to script creation of objects? Some reference each other.

    I'm writing a script that will add objects to a 10g schema. I have packages containing functions and procedures. The functions and procedures reference some views that also need to be added. The views themselves reference some of the package's functi

  • How to set the conversation id programmatically in a BPM process

    Hi all, I am using BPM/SOA 11g PS3. Is it possible to set the conversation id programmatically in a BPM process starting with a none start event? I know I can set it easily if I use a BPM process starting with a message start event. All I have to do

  • Cannot convert character sets for one or more characters

    Hello, Issue: Source File:   Test.csv Source file dropped on application server as csv file via FTP Total records in csv file 102396 I can able to load only 38,000 records after that I am getting error message  " convert character sets for one or mor

  • Is it possible to avoid duplicate material in Sale order creation

    Dear SD gurus Is it possible to avoid material duplication in va01 sale order creation. For amendment purpose the marketing user making new line item with amended qty instead of quantity change. kindly advise me to solve the problem. Thanks & Regards

  • Call_form problem in Forms 10g

    I am using Developer 10g R2. I tried to call a form named form1 from another form. But it can not open the form and shows the following error: FRM 40010: Can not read form form1. Then I tried other functions open_form, Go_form. But it does not work.