White iMac will not boot after 10.6.8 upgrade

I downloaded the 10.6.8 upgrade last night. This morning, the white plastic iMac will not boot.
I have tried evey known keyboard option.
I have tried booting from the snow leopard dvd.
I have zapped the pram.
Nothing!
Please, any help would be great.

We bought 2 iMac's 27inch with i7 Quad-core. Did the update a couple of hours ago. My Mac asked to reboot after update, but i didn't accept and worked with iTunes for a while. Then rebooted manually. After reboot it took about 15 minutes to reboot (light-blue screen with nothing on it, not even a mouse). My Wife also did the update of 10.6.8 and rebooted when asked. Her iMac also took 15 minutes to reboot, bus update was unsuccesful! So did update again and then denied reboot and rebooted manually! (Apple-logo and then choose "restart").
When we did that, iMac was very fast and updateproblem was solved! So deny reboot and reboot manually and problems are over. Same deal with 2 brandnew iMac. I'm guessing this is an issue. To much of a coincidence for me!

Similar Messages

IMac will not boot after 10.10.2 update

Hello all, I could really use some help. I downloaded 10.10.2 from the app store on my iMac (previously upgraded to Yosemite through app store), and when the system restarted, I would see the white screen with the apple logo and the progress bar about a third of the way across. then the system would ether restart or hang. Here is what I have done so far.
1. I am unable to boot to recovery mode using 'command R'... nothing happens and it goes back to the apple logo and a progress bar that get to a third of the way and stops.
2. I am able to press 'option' during boot and get 3 options for loading (system, recovery, and a Yosemite install disk i made on a USB). selecting any of these options returns me to the apple logo and the progress bar that gets stuck at a one third complete.
3. I am able to select safe and verbose mode. the machine will sometimes get all the way to "system up time in milliseconds" before it reboots.
4. I am able to boot to single user mode. I have run '/sbin/fsck -fy' until it no longer displays 'modification have been made' and it displays 'volume appears to be ok" (takes 2 runs). from here i have tried both rebooting, and exiting, both result in the white screen with the apple logo and the progress bar getting to a third of the way.
5. i have tried clearing the NVRAM
6. I don't have another mac with firewire or thunderbolt to try targeted disk mode
7. i have had 1 success in getting to the log in screen using verbose mode. during the boot there was a whole screen of the same line repeated many times, it said "BUG in process suhelperdt[167]: over-released legacy external boost assertions (1 total, 1 external, 0 legacy-external). after i logged in it reported that the system has un-expectedly shutdown, and that it would send a report to apple (is this a kernel panic?). i hit yes and then show the details. then the system hung up, and rebooted. then hung up again during boot with the same "BUG" message above.
I've got good time machine backups, and don't mind doing a complete reload if i can ever get to that option.
Thanks in advance for the help.

I have a 27 inch imac (10,1 late 09) that was doing the same intermittently during 10.10.2. In a fit of frustration, I updated yesterday to 10.10.3 and now the computer is doing exactly as you describe. I cannot get past the white screen at all. I have booted into recovery, verified and fixed the drive even though it it checked out fine. and attempted a fresh download on a clean partition. nada... i can get into safe mode, and I tried installing the SMC fan control, switching off transparency, and lowering my resolution. none worked.
I was convinced my hard drive was dying (when I had 10.10.2), and replaced it last week with a SSD. The SSD ran great for about a week, then had the same problems. I never had a problem with 10.10.1 or prior. I have checked my ram, and that does not fix the problem (swapping all four into the front dime slots in sequence).
This computer has run great since 09, and I have never had any issues until now, but it is now a very expensive paperweight. I cannot do the internet recovery that sets up the original OS the machine shipped with (too old for that feature), and it will not let me download a previous version of OS X from the app store (I have mavericks, lion, etc there).
I think my apple love affair is officially over. Looks like i will be searching for a pre-yosimite computer to download a usb version of mavericks or lion, and I sure as **** am not buying another apple product in the near future! I was very close to pulling the trigger on a new macbook, sure glad I did not waste my money -again-.

Imac will not boot after trying to upgrade OS

A friend gave me an iMac 266MHz, one of the old tangerine models. He thought the firmware was upgraded but it had an old OS. I installed my OSX on it but when it was shut down it will not reboot. I am getting the same error message as above. I tried to boot from an 8.5 installer disk but it will not work.
Do I need the original startup disks for this machine? I do not have them. Is there any tricks I should know about trying to boot from the disks? I have used macs for a little while but I am not very familiar with this area {boot errors}

ok you needed to upgrade the firmware before installing os x and now you need a reinstallation cd for the mac as well now don't panic you need to find a mac os 9.2.2 restore cd i use the gray cd on my imac and it works great then you need to insert the cd press c on the keyboard as the computer starts up then once the os 9.2.2 cd shows up and boots you need to format the hard drive let the mac choose the type of format then install os 9.2.2 then upgrade the firmware then reinstall mac os x but a warning here from what i have read at the forums here i don't know if mac os x is compatible with that version of mac so you may need to look at the support section here to find out or the os x section
I hope this helps

Computer will not boot after 10.6.8 upgrade

Just did the 10.6.8 upgrade to a computer and not it wont boot. Stuck at the grey start up screen with the apple and the spinning wheel of death. Zapped the PRAM to no avail and reset the SMU and still the same. Any advice?

Reinstall OS X without erasing the drive
Do the following:
1. Repair the Hard Drive and Permissions
Boot from your Snow Leopard Installer disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Utilities menu. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the installer.
If DU reports errors it cannot fix, then you will need Disk Warrior and/or Tech Tool Pro to repair the drive. If you don't have either of them or if neither of them can fix the drive, then you will need to reformat the drive and reinstall OS X.
2. Reinstall Snow Leopard
If the drive is OK then quit DU and return to the installer. Proceed with reinstalling OS X. Note that the Snow Leopard installer will not erase your drive or disturb your files. After installing a fresh copy of OS X the installer will move your Home folder, third-party applications, support items, and network preferences into the newly installed system.
Download and install the Combo Updater for the version you prefer from support.apple.com/downloads/.

My iMac will not boot up from the Leopard upgrade disk nor will it eject it.

My iMac is very slow and sluggish. Followed online instructions to use the Disk Utility to run repair. After doing so it told to reboot my system from the install disk and then run the Disk Uitility to run repair from it. I put in my Leopard upgrade disk and tried to reboot. I get the chime and the Apple logo and hear the disk trying to be read, but after about 5 minutes my iMac shuts completely off. I have tried to eject the disk using all the methods found in the community and nothing works. I want to try my orignal Mac OS X install disk to see if that works. My computer is about a 2007 model. It worked great until just a couple days ago. Frankly I can't afford to take it in so I will have to figure this out on my own with your help. :-(

I cannot open terminal. When booting I get the gray screen with the Apple logo and the twirling comb goes for a while and shut the computer completely off.
I got into the single-mode user and learned the following: disk1s3: I/O error. SAM Multimedia: Read & Write failed, SENSE_KEY = 0x03, ASC = 0x02m ASCQ = 0x00.
Singleuser boot -- fsck not done
Root device is mounted read-only.
If you want to make modifcations to files: /sbin/fsck -fy
/sbin/mount -uw /
I typed in the drutil eject and got:
SAM Multimedia: Read & Write failed, SENSE_KEY = 0x03, ASC = 0x02m ASCQ = 0x00.
Library not loaded. Reason: not suiteable image found.
It did find:
/system/library/rivateframeworks/installserver.framwork/versions/a/installserver : unknown file type, firfst eight bytes: 0xCA 0xfe 0xba 0xbe 0x00 0x00 0x00 0x04 Trace/BPT trap.
I have tried holding the left mouse key, the eject key and nothing happens. To bad I can't pull the
thing out with tweezers.
So where do I go from here?

Imac will not boot past Apple Logo

My imac will not boot after the good chime and apple logo (i don't even get a spinning wheel). I have held the option key down and selected the OS 10.6 disk with the same result. I was able to erase the drive and reinstall OS 10.6 using target mode and another computer. In target mode I can boot the other computer from the IMac HD but not the IMac. Have also tried holding the shift key and booting into safe mode with the same result. Additional note: I reset the PRAM and the SMU. At first on PRAM reset it would take 45 seconds for the machine to chime again, after OS reinstall and SMU reset, PRAM reset chimes within 10 seconds.... any help would be appreciated...

Kind of late but your solution helped me remember what once worked for me, a few years back.
Started iMAC in Target mode Used a firewire cable to a MacBook Pro
Started the Macbook Pro using the option Key and then restarted with the iMac as the Hard drive
Then I updated to 10.6.8 and allof the other updates.
shut down and rebooted and everything was fine.
But first I did quite a few other things before the update such as
It all started with a DiskWarrior finding overlapped files, I have been around the block a time or two so after it found three overlapped files, I shut down diskwarrior started up disk utility did a restore of the messed up drive to another external drive,
of course this copied overlapped files and all to the new external drive It took 24 huors or so, to back up the drive once it was done, I also tried a few times to correct the overlapped files to no avail,
so then I started the iMac up in target mode used the MacBook to format and erase the original drive, used the 10.6.3 DVD installer to install onto the hard drive, using the macBook DVD. After I was finished with the install to the iMAC,,,,,,,,,,this is where I got the three beeps like bad ram So idid the PRAM and SMC to no avail.
The operating system was evidently not new enough so once I did what i said at the begining of this post all went well.
Sometimes It is tough to remember some of the stuff that you learned several years ago.
and tired hard to forget.
I hoped this post does not scare away to many people, I was just about done with this computer until I read your post, one of several dozen, and it all came back to me.
Thanks a Bunch
I hope this can help others
themacprofessor

My imac will not load after I enter my password. The only thing I get is the arrow from my mouse on top of a blank white screen. Can anyone tell me what this is? I've restarted and turned off several times. I left it on in this state for 8 hours and

My imac will not load after I enter my password. The only thing I get is the arrow from my mouse on top of a blank white screen. Can anyone tell me what this is? I've restarted and turned off several times. I left it on in this state for 8 hours hoping it would reload and work. No luck.

Hello KCC4ME,
You may try booting your Mac in Safe Boot, as it can resolve many issues that may prevent a successful login.
OS X: What is Safe Boot, Safe Mode?
http://support.apple.com/kb/HT1564
If a Safe Boot allows you to successfully log in, you may have issues with one or more login itmes (while the following article is labelled as a Mavericks article, it is viable for earlier versions of the Mac OS, as well).
OS X Mavericks: If you think you have incompatible login items
http://support.apple.com/kb/PH14201
Cheers,
Allen

My 2011 IMac will not boot up past the White apple logo screen with the whirly circle

My 2011 IMac will not boot up past the White apple logo screen with the whirly circle. I have tried various commands but to no avail. does anybody have any advice?

Take each of these steps that you haven't already tried. Stop when the problem is resolved.
Step 1
The first step in dealing with a startup failure is to secure the data. If you want to preserve the contents of the startup drive, and you don't already have at least one current backup, you must try to back up now, before you do anything else. It may or may not be possible. If you don't care about the data that has changed since the last backup, you can skip this step.
There are several ways to back up a Mac that is unable to start. You need an external hard drive to hold the backup data.
a. Start up from the Recovery partition, or from a local Time Machine backup volume (option key at startup.) When the OS X Utilities screen appears, launch Disk Utility and follow the instructions in this support article, under “Instructions for backing up to an external hard disk via Disk Utility.” The article refers to starting up from a DVD, but the procedure in Recovery mode is the same. You don't need a DVD if you're running OS X 10.7 or later.
b. If Step 1a fails because of disk errors, and no other Mac is available, then you may be able to salvage some of your files by copying them in the Finder. If you already have an external drive with OS X installed, start up from it. Otherwise, if you have Internet access, follow the instructions on this page to prepare the external drive and install OS X on it. You'll use the Recovery installer, rather than downloading it from the App Store.
c. If you have access to a working Mac, and both it and the non-working Mac have FireWire or Thunderbolt ports, start the non-working Mac in target disk mode. Use the working Mac to copy the data to another drive. This technique won't work with USB, Ethernet, Wi-Fi, or Bluetooth.
d. If the internal drive of the non-working Mac is user-replaceable, remove it and mount it in an external enclosure or drive dock. Use another Mac to copy the data.
Step 2
If the startup process stops at a blank gray screen with no Apple logo or spinning "daisy wheel," then the startup volume may be full. If you had previously seen warnings of low disk space, this is almost certainly the case. You might be able to start up in safe mode even though you can't start up normally. Otherwise, start up from an external drive, or else use the technique in Step 1b, 1c, or 1d to mount the internal drive and delete some files. According to Apple documentation, you need at least 9 GB of available space on the startup volume (as shown in the Finder Info window) for normal operation.
Step 3
Sometimes a startup failure can be resolved by resetting the NVRAM.
Step 4
If you use a wireless keyboard, trackpad, or mouse, replace or recharge the batteries. The battery level shown in the Bluetooth menu item may not be accurate.
Step 5
If there's a built-in optical drive, a disc may be stuck in it. Follow these instructions to eject it.
Step 6
Press and hold the power button until the power shuts off. Disconnect all wired peripherals except those needed to start up, and remove all aftermarket expansion cards. Use a different keyboard and/or mouse, if those devices are wired. If you can start up now, one of the devices you disconnected, or a combination of them, is causing the problem. Finding out which one is a process of elimination.
Step 7
If you've started from an external storage device, make sure that the internal startup volume is selected in the Startup Disk pane of System Preferences.
Start up in safe mode. Note: If FileVault is enabled, or if a firmware password is set, or if the startup volume is a Fusion Drive or a software RAID, you can’t do this. Post for further instructions.
Safe mode is much slower to start and run than normal, and some things won’t work at all, including wireless networking on certain Macs.
The login screen appears even if you usually log in automatically. You must know the login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
When you start up in safe mode, it's normal to see a dark gray progress bar on a light gray background. If the progress bar gets stuck for more than a few minutes, or if the system shuts down automatically while the progress bar is displayed, the startup volume is corrupt and the drive is probably malfunctioning. In that case, go to Step 11. If you ever have another problem with the drive, replace it immediately.
If you can start and log in in safe mode, empty the Trash, and then open the Finder Info window on the startup volume ("Macintosh HD," unless you gave it a different name.) Check that you have at least 9 GB of available space, as shown in the window. If you don't, copy as many files as necessary to another volume (not another folder on the same volume) and delete the originals. Deletion isn't complete until you empty the Trash again. Do this until the available space is more than 9 GB. Then restart as usual (i.e., not in safe mode.)
If the startup process hangs again, the problem is likely caused by a third-party system modification that you installed. Post for further instructions.
Step 8
Launch Disk Utility in Recovery mode (see Step 1.) Select the startup volume, then run Repair Disk. If any problems are found, repeat until clear. If Disk Utility reports that the volume can't be repaired, the drive has malfunctioned and should be replaced. You might choose to tolerate one such malfunction in the life of the drive. In that case, erase the volume and restore from a backup. If the same thing ever happens again, replace the drive immediately.
This is one of the rare situations in which you should also run Repair Permissions, ignoring the false warnings it may produce. Look for the line "Permissions repair complete" at the end of the output. Then restart as usual.
Step 9
If the startup device is an aftermarket SSD, it may need a firmware update and/or a forced "garbage collection." Instructions for doing this with a Crucial-branded SSD were posted here. Some of those instructions may apply to other brands of SSD, but you should check with the vendor's tech support.
Step 10
Reinstall the OS. If the Mac was upgraded from an older version of OS X, you’ll need the Apple ID and password you used to upgrade.
Step 11
Do as in Step 9, but this time erase the startup volume in Disk Utility before installing. The system should automatically restart into the Setup Assistant. Follow the prompts to transfer the data from a Time Machine or other backup.
Step 12
This step applies only to models that have a logic-board ("PRAM") battery: all Mac Pro's and some others (not current models.) Both desktop and portable Macs used to have such a battery. The logic-board battery, if there is one, is separate from the main battery of a portable. A dead logic-board battery can cause a startup failure. Typically the failure will be preceded by loss of the settings for the startup disk and system clock. See the user manual for replacement instructions. You may have to take the machine to a service provider to have the battery replaced.
Step 13
If you get this far, you're probably dealing with a hardware fault. Make a "Genius" appointment at an Apple Store, or go to another authorized service provider.

IMac will not boot up, all I get is white screen help

MY iMac will not boot up, all I get is white screen?
what do I need to do to start machine please?

Start with a google search for white screen site:apple.com and peruse the many hits.

Intel iMac will not boot past gray screen

Intel iMac will not boot past gray screen
my system:
new (month old) 24" intel imac, 2.8 ghz, 4 gb ram.
running: leopard (upgraded from tiger, which was pre-installed at purchase), installed 10.5.1 update right before this huge problem occurred.
install discs on-hand: two-disc tiget set, single leopard upgrade disc.
what led to this:
i wanted to install windows using bootcamp on a 50 gb partition.
at this point i was running leopard 10.5
i followed all bootcamp instructions, printing out the guide, as well. once i got into the windows setup, i was prompted to choose a partition to install windows. unlike the bootcamp guide, which showed three partitions, one clearly labeled "bootcamp", i saw only one partition. not wanting to risk writing over my mac partition, i quit the setup and rebooted the mac os. after some googling around, i looked for firmware updates (didn't need any), and then software updates. i decided to try updating to 10.5.1.
i then ran through boot camp again, deleting my previous windows partition, creating a new one, and moving forward as before. once again, i was only shown one partition to choose from in the windows setup. i exited the setup again to reboot through the mac os, but this time, i was only given a blank gray screen.
here's what i have tried so far:
booting from a CD, holding down the C or D keys: no response (in fact, i have to restart the computer holding down the mouse button to be able to eject the CD)
booting with option key held down: gray screen
booting with option key held down with external bootable firewire drive attached: the firewire drive appears as a boot icon, and i can click on it within a five second window, but then the screen freezes after that time period, and nothing changes
booting into target mode while attached to another mac: gray screen (no firewire icon, and drive never shows up on other mac)
resetting NVRAM: i'm able to hear the boot chimes, but no difference in performance. gray screen every time
Safe boot: nothing but a gray screen
Verbose mode: gray screen
Single user mode: gray screen
Single user mode with firewire drive attached: occasionally (not every time), i am able to get the white on black terminal to show up. from here, i'm able to run fsck, but it appears to only be checking the firewire drive. i have tried several times to boot from here, and once it took me to a blue screen with movable arrow cursor, but it never went beyond this.
is there anything else left to try before taking it to apple?
any help would be greatly appreciated.
thanks,
Casey Burns
Casey Burns Illustration and Design
http://CaseyBurns.com

I'd call Apple support at this point. You'll need
to put this issue on the record.
Call U.S. iPod and Mac technical support: 1-800-APL-CARE (1-800-275-2273)
The wait may be long for an agent to come on the line
so expect that and have some other stuff to do in the meantime.
If you have the applecare protection plan, I'd ask about "onsite"
service.
I like your work ! Good luck !
Slim
Message was edited by: slimpikkunz

IMac will not boot up when printer is plugged in USB

After buying my new iMac (with Tiger) I successfully transfered everything from my old iMac (with Panther) and all was well.
The problem is that when my printer (Canon Pixma MP130) is plugged in on start up, the iMac will not boot up (no gears turning on the white/grey screen). When I unplug the printer from the USB and start it up, it works fine. Its not a super big deal because I can just plug the printer in when I need it. But why does it do this?
I foound on the internet someone else who had the same issues. It was suggested to him to search the printer manufacturers website for updated drivers. I did this, installed them etc..... still no luck.
I am without any mac guru's here in Yellowknife......help!
Angie

Hello there,
I hope it is OK to recycle this old thread.  I did not want to create a new one since I am experiencing the exact same issue as the original poster *flying girl* as well as other posters in the following threads:
http://discussions.apple.com/thread.jspa?messageID=4190807
http://discussions.apple.com/thread.jspa?messageID=3950255
http://discussions.apple.com/thread.jspa?messageID=4201169
http://discussions.apple.com/thread.jspa?messageID=4490899&#4490899
http://discussions.apple.com/thread.jspa?messageID=4470944
I have two Macs, a PowerBook G4 and an Intel iMac 20" (Aluminum)--please refer to my signature or profile for the specs of these machines.  Of course, I got the PowerBook before I got the iMac.  I am running the latest version of the Canon MP130 drivers, printer drivers version 4.8.3 and scanner drivers version 12.11.0, on both machines.
When I turn on my PowerBook with the Canon PIXMA MP130 multifunction turned ON and connected via USB to the PowerBook, the PowerBook boots up just fine.  I have even experimented with both a USB hub and a direct connection to the Canon MP130, and the PowerBook boots fine in both instances.
However, when I turn on my iMac with the Canon MP130 turned ON and connected via USB to the iMac, the startup tone plays, and then the iMac hangs at the blue/gray solid screen--it does not even show the Apple logo or the spokes--that is, until I turn the Canon MP130 OFF.  When I turn it off, the Apple logo appears, the spokes move, and my iMac boots up just fine.  And as long as the MP130 is OFF, I can boot the iMac fine from scratch too.
I tried starting in verbose mode (⌘V) and single-user mode (⌘S), and the gray/blue screen still appears after the startup tone plays; again, if I turn the Canon MP130 OFF, the rest of the boot sequence resumes as normal, and only then do I get to see the descriptive text for those startup modes.  But the text goes by so fast that I miss most of it--I did manage to catch something that said something like "get full config descriptor = NULL," but I am not sure if that was the exact wording.  I would need a good camcorder or even just a digital camera or another device to capture exactly what the screen says in verbose mode.  If I had those options, I would post pictures here.
I was thinking about contacting Canon, but since the issue happens on one Mac only, I figured they would tell me that it is a problem with my Mac.  So hopefully posting the information here is OK.
Another key feature is that the Canon MP130 has a built-in card reader.  I made sure that my Startup Disk preferences were set to boot from the system drive, and they still are.  And I have reset the SMC and PRAM on the iMac.
I would like to mention the following link:
http://www.ehmac.ca/anything-mac/50389-intel-imac-wont-boot-when-canon-printer-p lugged.html
If you go to page 2 on that above thread, it shows one user who allegedly physically disconnected the card reader connection from the inside of the Canon MP130 (I would NOT recommend that myself).  I just wonder if there is a more feasible resolution to this issue.
Does anyone else experience the same issue with other printers or multifunctions?  Also, why does the issue occur only on my Intel iMac 20" (aluminum), and NOT on my PowerBook G4?
Please let us know about your experience as it seems many of us are at a loss for a solution.
Thank you very much for your help; we await!  :)
Cya!
\m/ Mad Metal Mage \m/

IMac will not boot, hard drive file problem? Can't install OS in 2nd part.

The iMac will not boot. The Apple displays on the screen, the cursor spins for awhile, and then it loops into a reboot effort.
Last night, I was doing a lot of custom file sharing settings using the include enclosed folders option at the bottom of the Get Info window.
Question 1: Could that file sharing process have messed things up?
In an effort to get things going........ A few weeks back, I used Disk Utility to create a 2nd partition, with the intent of installing Ubuntu Linux there. I never attempted the install, as far as I can remember, while playing with the Ubuntu Live CD. So, I thought I would install 10.5.6 from the CD in the 2nd partition. But I get an error message that says "The installer could not create the folder "/Volumes/Ubuntu 9.10/BaseSystem.pkg.161nDNDdQ.""
Question 2: I also shared that partition, could that have caused the OS install failure?
Question 3: If I understand the book correctly, I can try to install the OS from the CD on the 1st partition, and not lose my data, correct? Unfortunately, I don't have any backup for the data, as I don't own any drives large enough yet to accommodate the data on the drive.
Question 4: Anyone have any other thoughts as to what ent wrong?

Hi, Grant.
Sometimes, it just pays to think on a problem. I awoke thinking, if it will boot the OS X install CD, it ought to boot my Ubuntu Live CD. And then, maybe I can change permissions on the first partition. As soon as I thought that, it occurred to me, if the problems are with the permissions, what if I used the OS X disk, and erased (formatted) the Ubuntu partition. That should set all the permissions on that partition back to default. Would OS X install then to the Ubuntu partition?
You better believe it did!! I'm typing this from the Mac after updating my 10.5.6 to 10.5.8 in the 2nd partition, and I'm booting from the 2nd partition.
I then did as you suggested, and from the Mac, I repaired the permissions to the first partition. But, the result was the same, there are a few permissions that do not match, and Disk Utility cannot, does not, or will not correct them.
I'm currently downloading the 10.5.8 combo update .dmg file. My thought is to burn that to a disk, and then install it over the version in partition 1. And trust that the current installation on partition 1 does not have any cross linked files that will destroy some data.
I do have some old ATA IDE drives I can hook externally to the Mac, and copy some of the information I have from the Mac to those drives before doing the 10.5.8 install.
Can you think of a better solution?

Sometimes iMac will not boot up

hey guys i have been having this on going problem for about a week now. Ok so here's what's happening, this usually happens at night. It seems that my iMac will not boot up, I have my computer put to sleep when I go to sleep and I can wake it up again in the morning. Now when I go out in the evening today for example, I just got home, woke my computer up and everything seemed fine. After a little bit my computer froze so, I restarted it and it will not boot up it would get stuck on the gray screen, sometimes the apple and the spinning thing under it (not the beach ball one) would show up and sometimes I would have just a grey screen. Over the past week I've tried the following:
Reset the Pram
Booted up from the installation cd.
Removed all the cords waited for a couple min. then tried again
Eventually I can boot up, However I am very concerned to what the problem might be.
O yea I also ran a permission repair
One final thing if knows how to protect macs with an anti virus or something similar, it would really help me out.
Thanks

Hi Karim
The symptoms you describe could be caused by bad RAM.
Follow this link to learn about testing memory.
With your iMac you should have received an Apple Hardware Test CD, if not it's included on the Installation DVD (it would state that written somewhere on the DVD). There's also a RAM test included, but it isn't as dependable as memtest (mentioned in the link above) in my experience.
Follow this link to learn how to start the Apple Hardware Test.
Kind regards
--greg

My iMac will not boot through Snow Leopard but will boot through Windows OS

My 2010 iMac will not boot in Snow Leopard, only Windows. Have tried reinstalling Snow leopard a few times and works only for a couple of minutes before freezing and doesnt reboot. Windows works perfect. Snow leopard just doesnt want to boot up past the Apple Logo. It was working fine one day and the next day it froze up and was able to reboot back into Snow Leopard but kept freezing. Now it doesnt load at all into Mac OS.
Brian

Possible scenarios:
1: The 10.6.3 SL retail disk is bad, it happens.
2: Your not using the 10.6.3 SL retail disk but one from another machine which doesn't have the drivers for that machine.
3: Your optical drive is funky or some other hardware issues.
4: Your trying to install 10.6 onto a PowerPC based Mac, no can do.
5: Your not using a wired keyboard for boot key commands, have some other hardware conflicts.
Possible solutions.
1: Copy the SL 10.6.3 disk using Disk Utility to another DVD, the error checking may resolve the original disk's issue.
http://www.brokenhomeboy.co.uk/pierow/blog/2011/10/make-a-bootable-backup-snow-l eopard-install-disc/
2: Make a SL bootable USB
http://www.maciverse.com/install-os-x-snow-leopard-from-usb-flash-drive.html
3: Call Apple for a new 10.6.3 disk (and make copies for backup before Apple discontinues selling it)
If your upgrading to 10.6 to get to 10.6.8 to upgrade to 10.7, be warned of this:
1: Your 10.5 software will not work in 10.7, no more Rosetta or PPC based code.
2: Your hardware will not qualify if it's a 32 bit Intel Core Duo, also you may experience slowdowns in performance over 10.6 (10.6 is the fastest OS X version for Intel Macs) in older Intel hardware (I suggest Early 2011 Mac's and later only for Lion)
3: Mountain Lion 10.8 is reportingly coming out this summer and will not run on a lot of older Intel based Mac's because of heftier graphics requirements.
4: 10.6 has the widest range of current avaialble software and drivers for third party hardware.
My advice, stick with 10.6.8 and stay there, buy a new Mountain Lion machine after this summer. Skip Lion completely.

My iMac will not boot past the logo and spinning gear

My iMac will not boot past the logo and spinning gear (After a Rogue Amoeba update). I can't access the recovery disk I made on a flash drive. (Am I doing it correctly? - Hold down option while switching on? It just stays on the logo). What (if anything) can I do please?

If you installed Lion onto your machine, it should have created a Recovery HD (hidden from view, but visible in Disk Utility with its Debug menu enabled, under Show all Partitions).
That article states:
Note: In order to create an external Lion Recovery using the Lion Recovery Assistant, the Mac must have an existing Recovery HD.
Would I see the recovery menu (by holding down option on power up)
Yes.
if there was no recovery disc connected do you think?
Shouldn't matter, since your int HD is always connected.

White iMac will not boot after 10.6.8 upgrade

Similar Messages

Maybe you are looking for